Secondary vrs sub interfaces
Hi everyone, What's the difference between secondary and sub interfaces and when and where are they applied. Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Email vrs Web Browsing
Hello guys, We have this wireless internet distribution through a Cisco 3600 backbone router to the internet. We have set up one wireless site which can browse and send emails. The 2nd site has the same setup, the only difference being that it has a different network address, cannot browse. Only emails can be sent (i.e from out Microsoft outlook) and yahoo messenger can be used to chat. No web browsing is successful. When you try to browse, it says web site found and waiting for reply and thats it! You can ping yahoo, netscape etc, etc with a response, but just cannot browse. What could be wrong Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Email vrs Web Browsing
Get free email and a permanent address at http://www.netaddress.com/?N=3D= 1 > Received: from groupstudy.com [63.104.50.75] by nmcst150 via mtad (34FM.0700.12.01) > with ESMTP id 628FBXoG20154M21; Sat, 24 Feb 2001 14:32:57 GMT > Received: from localhost (mail@localhost) > by groupstudy.com (8.9.3/8.9.3) with SMTP id KAA09050; > Sat, 24 Feb 2001 10:30:14 -0500 > Received: by groupstudy.com (bulk_mailer v1.12); Sat, 24 Feb 2001 10:06:01 -0500 > Received: (from listserver@localhost) > by groupstudy.com (8.9.3/8.9.3) id KAA06136 > GroupStudy Mailer; Sat, 24 Feb 2001 10:06:00 -0500 > Received: from nw178.netaddress.usa.net (nw178.netaddress.usa.net [204.68.24.78]) > by groupstudy.com (8.9.3/8.9.3) with SMTP id KAA06116 > GroupStudy Mailer; Sat, 24 Feb 2001 10:05:59 -0500 > Received: (qmail 18538 invoked by uid 60001); 24 Feb 2001 13:57:43 - > Message-ID: <[EMAIL PROTECTED]> > Received: from 204.68.24.78 by nw178 for [63.109.248.105] via >web-mailer(34FM.0700.15B.01) on Sat Feb 24 13:57:43 GMT 2001 > Date: 24 Feb 2001 06:57:43 MST > From: Charles Nunie <[EMAIL PROTECTED]> > To: [EMAIL PROTECTED] > Subject: Email vrs Web Browsing > X-Mailer: USANET web-mailer (34FM.0700.15B.01) > X-MIME-Autoconverted: from quoted-printable to 8bit by groupstudy.com id KAA06116 > Sender: [EMAIL PROTECTED] > Reply-To: Charles Nunie <[EMAIL PROTECTED]> > Precedence: bulk > > Hello guys, > > We have this wireless internet distribution through a Cisco 3600 backbone > router to the internet. > > We have set up one wireless site which can browse and send emails. The 2nd > site has the same setup, the only difference being that it has a different > network address, cannot browse. Only emails can be sent (i.e from out > Microsoft outlook) and yahoo messenger can be used to chat. > > No web browsing is successful. When you try to browse, it says web site found > and waiting for reply and thats it! You can ping yahoo, netscape etc, etc with > a response, but just cannot browse. > > What could be wrong > > Dzilo > > > Get free email and a permanent address at http://www.netaddress.com/?N=1 > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
HHEELLPP!!
We have a wireless Internet distribution. Our radios plug into a 3600 Cisco. We keep getting this error "00:26:50: %AMDP2_FE-5-LATECOLL: FastEthernet0/1 transmit error" This did not happen before. This slows down the Internet Access the eventually throws everyone off. Please HELP Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
HH EE LL PP !!
We have a wireless Internet distribution. Our radios plug into a 3600 Cis= co. We keep getting this error = "00:26:50: %AMDP2_FE-5-LATECOLL: FastEthernet0/1 transmit error" This did not happen before. This slows down the Internet Access the eventually throws everyone off. Please HELP Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=3D= 1 > Received: from 204.68.23.64 by nwcst319 for [63.109.248.105] via >web-mailer(34FM.0700.16.05) on Fri Mar 2 18:57:43 GMT 2001 > Date: 2 Mar 2001 11:57:43 MST > From: Charles Nunie <[EMAIL PROTECTED]> > To: [EMAIL PROTECTED] > Subject: HHEELLPP!! > X-Mailer: USANET web-mailer (34FM.0700.16.05) > Mime-Version: 1.0 > Content-Type: text/plain; charset=US-ASCII > Content-Transfer-Encoding: quoted-printable > > We have a wireless Internet distribution. Our radios plug into a 3600 Cis= > co. > We keep getting this error = > > > "00:26:50: AMDP2_FE-5-LATECOLL: FastEthernet0/1 transmit error" > > This did not happen before. This slows down the Internet Access the event= > ually > throws everyone off. > > Please HELP > > Dzilo > > > Get free email and a permanent address at http://www.netaddress.com/?N=3D= > 1 > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: [RE: HH EE LL PP !!]
Thanx a million. There was a an interface mismatch. Were ok now. "McMasters, Eric" <[EMAIL PROTECTED]> wrote: Verify that both devices are set to the same duplex either half or full. Don't trust the auto settings because they usually don't work. Hard set the interfaces at each end to 100Mb full duplex and this will eliminate the possibility of collisions. Let me know how it works. Eric -Original Message- From: Charles Nunie To: [EMAIL PROTECTED] Sent: 3/2/01 12:26 PM Subject: HH EE LL PP !! We have a wireless Internet distribution. Our radios plug into a 3600 Cis= co. We keep getting this error = "00:26:50: %AMDP2_FE-5-LATECOLL: FastEthernet0/1 transmit error" This did not happen before. This slows down the Internet Access the eventually throws everyone off. Please HELP Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=3D= 1 > Received: from 204.68.23.64 by nwcst319 for [63.109.248.105] via web-mailer(34FM.0700.16.05) on Fri Mar 2 18:57:43 GMT 2001 > Date: 2 Mar 2001 11:57:43 MST > From: Charles Nunie <[EMAIL PROTECTED]> > To: [EMAIL PROTECTED] > Subject: HHEELLPP!! > X-Mailer: USANET web-mailer (34FM.0700.16.05) > Mime-Version: 1.0 > Content-Type: text/plain; charset=US-ASCII > Content-Transfer-Encoding: quoted-printable > > We have a wireless Internet distribution. Our radios plug into a 3600 Cis= > co. > We keep getting this error = > > > "00:26:50: AMDP2_FE-5-LATECOLL: FastEthernet0/1 transmit error" > > This did not happen before. This slows down the Internet Access the event= > ually > throws everyone off. > > Please HELP > > Dzilo > > > Get free email and a permanent address at http://www.netaddress.com/?N=3D= > 1 > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
GROUPSTUDY REGISTRATION
Hello everyone, My pal wants to join in on this studygroup but the web page is off. Any help? Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Deciphering error logs
Hello, Where can I get interpretation on the errors in my log file? Meanwhile can someone decipher this: 00:00:02: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram 00:00:13: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down 00:00:13: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up 00:00:13: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up 00:00:13: %SYS-5-CONFIG_I: Configured from memory by console 00:00:14: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed sta te to up 00:00:14: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, chang ed state to down 00:00:14: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, change Thanks Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: [RE: Password Utility]
Hi, I am interested, pleasen give more info [EMAIL PROTECTED] (Timothy Metz) wrote: There's also one for the palm pilot, I'll look up the url if you're interested... Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > John Neiberger > Sent: Monday, March 19, 2001 5:53 PM > To: [EMAIL PROTECTED] > Cc: [EMAIL PROTECTED] > Subject: Re: Password Utility > > > http://www.alcrypto.co.uk/cisco/ > > >>> "The.Rock" <[EMAIL PROTECTED]> 3/19/01 9:39:18 AM >>> > Anyone have the password hash utility to de-crypt a password? > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Aeronet Comparisons
Hello Everyone, We are gearing up to launch the Aeronet in our local market. Can anyone tell em how well the Aeronet compare with other Wireless LAN equipment on the market. Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 Hi everyone, we have implemented both a radio and a dial-up link from a branch office to the head office of a firm. since the branch office has no router but rather a switch, we have set up each workstation/equipment on the lan to see the radio as its primary gateway and the branch dial-up access server as the secondary gateway. how do we get the cisco4500 router at the head office to accept information through the dial up when the radio link goes down. better still how do we get the cisco4500 to dynamically route between the two links Get free email and a permanent address at http://www.netaddress.com/?N=1
Re: [re - A silly question - modified]
Thanx. For years I've tried to figure that one out. Dzilo [EMAIL PROTECTED] wrote: I believe it is ctrl+shift+6 al at the same time. Gene >While I try to ping a remote ip address from the router CLI, I am asked to >type escape sequence to abort. > >I know I would sound silly asking this question, But to be honest, I don't >know the answer for this. Can anyone tell me what is the escape sequence to >abort pinging from the CLI. > > >*** I am pinging from within a telnet session to the Router *** > >Thanks in Advance, >S.Kalidasan _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: [re - A silly question - modified]
Thanx. For years I've tried to figure that one out. Dzilo [EMAIL PROTECTED] wrote: I believe it is ctrl+shift+6 al at the same time. Gene >While I try to ping a remote ip address from the router CLI, I am asked to >type escape sequence to abort. > >I know I would sound silly asking this question, But to be honest, I don't >know the answer for this. Can anyone tell me what is the escape sequence to >abort pinging from the CLI. > > >*** I am pinging from within a telnet session to the Router *** > >Thanks in Advance, >S.Kalidasan _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Wierd network
Hi everyone, We have this network setup linking two offices. There was a link failure and we had to replace the routers. The same settings were used but. The server cannot ping across the network (only the immediate router interface). All workstations can ping across and some were also working off this same server. The server was isolated and its IP used on a laptop could go across!!. The server, routers and everything was working the night before the breakdown and everything had been reset. Its working now but, what caused it? It just came up after about 3 hours. Regards, Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Timeouts on Ethernet and WAN interface
Hi, We have this 3600 router connected to a WAN through a PRI interface an a LAN through an ethernet interface. We have recently been experiencing timeouts on these interfaces. Over noght the timeouts did not appear, just this morning it has started again. What could be wrong? Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Netflow Bandwidth Manager
Hello, We are using a cisco 3620 as our backbone router to the internet running 12.1(5) IOS. We have a billing system (RODOPI) which is able to run with Cisco's Netflow for bandwidth management. To connect to the internet we have a WAN which uses private and public IP addresses and we want to use the Netflow to perform bandwidth management. This would assign a particular bandwith (eg. 64, 128kbps) to a public or private IP address on our WAN. No matter the location of the IP address on our WAN, we would want that assigned bandwidth to be assigned to that IP address. Please advise on the version of IOS we need to upgrade to and the configuration parameters for the configuration of the bandwidth manager. Regards, Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Crazy 2611
Hi everyone, We have two Cisco 2611 routers which we intend to use for VoIP for a client. It has the 11.3(2) XA4 version of bootstrap and an 11.3T IOS which we replaced with 12.0(7) XK1. Each time we issue commands like copy run start or write mem, it says: Attempting to overwrite an NVRAM configuration previously written by a different version of the system image and then asks for confirmation after which it reboots without making any permanent changes. It also says system received a segV exception. Other confirguration commands like dial-peer voice. pots, show run, more system: running - config etc. also causes the system to reboot in which situation all configurations are lost. What could be wrong please. Regards, Francis Amanor Get free email and a permanent address at http://www.netaddress.com/?N=1 **NOTE: New CCNA/CCDA List has been formed. For more information go to http://www.groupstudy.com/list/Associates.html _ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Sniffer Pro 3.5
Hi everyone, I bought this Sniffer Pro 3.5 which looks great. Can I have a URL where I can info on the best way to understand and use it? Regards, Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Dynamic routing on cisco4500
Hi everyone, we have implemented both a radio and a dial-up link from a branch office to the head office of a firm. since the branch office has no router but rather a switch, we have set up each workstation/equipment on the lan to see the radio as its primary gateway and the branch dial-up access server as the secondary gateway. how do we get the cisco4500 router at the head office to accept information through the dial up when the radio link goes down. better still how do we get the cisco4500 to dynamically route between the two links Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE:Ethernet to Serial Converters available!
Hi Guys, There is an ethernet to serial converter from "Avaya Communications". Unfortunately these are about to be discontinued. Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: [RE: utilization rate calculation]
Hi, Talking about MIB II etc, where can I find information on these definitions and how to use SNMP with its variables? I mean all there is to know about SNMP!! Thanks in advance Dzilo "Luong, David" <[EMAIL PROTECTED]> wrote: Thank-you John for the clear explaination. I think I got confused when the book stated "MIB II variables are stored as counters, you must take two poll cycles...". Two? why two? But now I know that is just a minimum to get a rate calculation..not a value that u MUST use. -Original Message- From: John Neiberger [mailto:[EMAIL PROTECTED]] Sent: Monday, April 02, 2001 10:17 AM To: [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Subject: RE: utilization rate calculation You can poll it as often as you feel like. Look at it like this, we'll use a car as an example. Let's say you want to know how fast a car is going and the only tools you have available are a stopwatch and the odometer on the car. The speedometer is broken. If you only look at the odometer once and it says "100", does that tell you anything about the speed of the car? Nope. However, if you look at the odometer again after one minute and it says "102" then you know two things: 1) the car has gone two miles in one minute and hence is going 120 miles per hour, and 2) the driver should lose his license. (No offense Dave, I know you'll read this!) The same principle holds for MIB counters. The counters we're talking about increment once for each byte transmitted or received. Looking at it once doesn't help you much because you can't derive a rate from a single sample. If you have a lot of traffic perhaps one sample a minute isn't good enough for you, especially if the traffic is bursty. In a situation like that you might want to sample every 5 or 10 seconds just for fun to watch the ebb and flow of traffic on a link. >>> "Luong, David" <[EMAIL PROTECTED]> 4/2/01 10:30:05 AM >>> It makes more sense now. So it is like 2 polling cycle is MINIMUM in order to get a rate? I could use more than 2? David. -Original Message- From: John Neiberger [mailto:[EMAIL PROTECTED]] Sent: Monday, April 02, 2001 8:25 AM To: [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Subject: Re: utilization rate calculation I'll try to restate this in a way that makes sense, but the text you quoted says it pretty well. The MIB data you are accessing is stored as a counter that increments for each byte transmitted and received. Let's say you polled the router and got this information: InOctets: 543980 OutOctets: 234095 Does that tell you anything? Not really. However if you wait a minute and poll it again you could see the amount of traffic in and out of that interface over a period of time, which gives you a rate. A single poll will not give you any usefull information. To get a rate, you need to sample the data over time. In this case the data is stored in bytes so you multiply times eight to get the rate in bits per second. Does that help? If not, I'll try again later after some more coffee. John >>> "Luong, David" <[EMAIL PROTECTED]> 4/2/01 8:50:40 AM >>> Hi Techies, I have recenty been reading Cisco Press' new book called "Peformance and Fault Management" and they stated to measure utilization on a WAN interface (full-duplex); it is recommended to use the following formula: max ( delta(ifInOctets), delta(ifOutOctets) x 8 x 100) -- (number of seconds in delta) x ifSpeed They state because of "MIB II variables are stored as counters, you must take two poll cycles and figure the difference between the two" hence the delta number. I don't understand why two poll cycles are needed and why is using "counters" attributed to this? Thanks, David Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Cisco2600 proxy
Hi Guys, How can a Cisco be setup as a proxy server. Any leads to sites would also be welcome. Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: [7:43]
Hi, The 2600 is between a wireless network and our POP. All our wireless Internet subscribers access the Internet through this router. We want to be able to monitor and control all wireless users (proxy type of thing) Regards, Dzilo Priscilla Oppenheimer wrote: What do you want it to proxy? It can act as a proxy in a variety of ways. Priscilla At 12:04 PM 4/9/01, Charles Nunie wrote: >Hi Guys, > >How can a Cisco be setup as a proxy server. Any leads to sites would also be >welcome. > >Dzilo > > >Get free email and a permanent address at http://www.netaddress.com/?N=1 Priscilla Oppenheimer http://www.priscilla.com Get free email and a permanent address at http://www.netaddress.com/?N=1 Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=43&t=43 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
QoS [7:1346]
Hi, Can Cisco 2600 and 3600 be configured to provide Quality of Service? We want to dedicate bandwidth to our wireless Internet subscribers Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=1346&t=1346 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
OT quick, easy & cheap [7:4989]
Hi Guys, Our WAN interface are all ethernet. We have a bandwidth manager in place to manage bandwidth over our WAN. What is the quickest, easyest and cheapest way to measure the throughput to a client which has been set to say 64k. Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=4989&t=4989 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: [Re: OT quick, easy & cheap [7:4989]
Hi, All traffic destined for the WAN goes over the ethernet interface. Its a private network wholly owned by a Bank. The radios used are supposed to have a throughput of 500kbps which is very very suspect. We want to check our throughput. These same radios are being used for broadband Internet Access for which we would also like to determine the throuhghput. Regards, Dzilo David Chandler wrote: Need more Details. 1. Is all of your traffic destined for the WAN being passed to a service providers Router across an ethernet connection? 2. Does the WAN provider have 64K links to the clients? 3. Is #2 why you are looking for a way to monitor throughput? DaveC Charles Nunie wrote: > > Hi Guys, > > Our WAN interface are all ethernet. We have a bandwidth manager in place to > manage bandwidth over our WAN. What is the quickest, easyest and cheapest way > to measure the throughput to a client which has been set to say 64k. > > Dzilo > > > Get free email and a permanent address at http://www.netaddress.com/?N=1 > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Get free email and a permanent address at http://www.netaddress.com/?N=1 Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=5184&t=4989 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Attractive Jumpers [7:7950]
Hi, We are adding extra mem to a 1700 router. The router does not recognise the extra memory (16MB). What do I do? There are some jumpers which look attractive. Would shifting them help? Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=7950&t=7950 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Frame Relay Presentation
Hi, I need information on Frame Relay for a presentation. Can someone give me a lead to a web page? Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
NAT Configuration
Hi, How would you configure network address translation (NAT) on a cisco router, and what series is recommended Dzilo Get free email and a permanent address at http://www.netaddress.com/?N=1 ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]