RE: VoIP Question AGAIN... [7:57747]
Andrew- Without having done this, I could be wrong, but from your excerpt "You can think of the ephones with the numbers that were assigned to the ephone-dn's as FXS ports on the routers.", I would say then that all you have to do is create your dial-plan, and then define VOIP Dial-peers with the destination target being the IP address of the IP Phones. If it is that simple, then you will up and running in a heartbeat. Be sure and look at cisco's router to router (FXS to FXS) dial-peer samples to get an idea of your syntax. You may have to play around with voice quality settings though. Good luck Mark (Aspiring AVVID Engineer/Architect) :) -Original Message- From: Andrew Dorsett [mailto:[EMAIL PROTECTED]] Sent: Wednesday, November 20, 2002 8:07 AM To: [EMAIL PROTECTED] Subject: Re: VoIP Question AGAIN... [7:57747] Bruce - Actually I'm not missing any pieces. Check out this link on the CCO to see exactly what I'm trying to accomplish: http://www.cisco.com/en/US/tech/tk652/tk701/technologies_configuration_e xample09186a00800ffdcc.shtml#background The router (3640,etc) utilizes the ITS feature set to act as the call manager for the network and create a small IP Key system without a few of the call manager features that I don't need in this case. And yes I want to use the 79xx phones behind the switch that I didn't mention is behind the router. I will use the FXO ports on the router to plug the incoming lines into. The page shows everything from how to do hold music to how to configure the phones XML interface. However it leaves out the PSTN setup section which is where I'm stuck at. I think I can do a session target to the ephone-dn but I'm not sure of the syntax. "Configuring the PSTN Connection on the Cisco ITS Router Assuming that the ITS router has voice interface cards, you will now want to configure those cards so that calls can be placed to and from the IP phones. This is not significantly different than other voice connections on a router. You can think of the ephones with the numbers that were assigned to the ephone-dn's as FXS ports on the routers." Thanks, Andrew On Wed, 20 Nov 2002, Bruce Enders wrote: > Andrew, > You are asking how to set something up without all the pieces necessary > to make it work. And you are describing developing a dialplan that does > not adhere to common conventions. That part is okay, you can define how > you route calls in-to and out-of your own voice network pretty much any > way you want. > The 3640 with an analog FXO is okay to act as a gateway to the PSTN. The > same router with FXS VIC ALSO will allow you to connect and originate > calls internally. However, you state you want to place "VOIP" phones on > the network behind the 3640. What "VOIP" phones would those be? If you > mean 79XX series IP Telephones from Cisco, you also need a CallManager > Server to control those phones. > As far as the dialing rules in this network, it is up to you what you use > to direct calls out to the world. Using "9" to classify all telephone > numbers that follow it as being sent to the PSTN is a convention not a > rule. The only real rule is that you have to give the system the means to > route a call based on what the User dials. AND, if you are handing the > call off to the PSTN or any other telephone switch, you have to give that > switch the call routing information (telephone number) that it needs to > route the call. > In coming calls are a whole different topic. Try reading one of the many > VoX books that are now available. > Hope this helps, > Bruce > > Andrew Dorsett wrote: > > Second call for this one. I never received any answers to my question. I > want to know how to setup the link between the VoIP phones and the FXO's. > Basically a dialplan, but how do I route inbound calls from the PSTN to > the VoIP phones? And how do I route outbound calls from the VoIP phones > over > the FXO to the PSTN? I would like to avoid a system that uses 9 to dial > an outside line. I want to do direct dialing to the PSTN without > any special steps. > > Thanks, > Andrew > > On Thu, 14 Nov 2002, Andrew Dorsett wrote: > > Hey everyone, I'm playing with an idea. I want to get ahold of a 3640 > with FXO's and interface it to the PSTN and connect to some VOIP phones > on > a network behind it. I have done all of my research on the CCO and have > found how to configure everything for phone connection and FXO > > configuration. > > However I haven't found out how to configure dialplans to dial the > outside > world. I basically need one that would say "all 4 digit dialed calls are > VoIP phones and all other numbers are outside
Re: VoIP Question AGAIN... [7:57747]
Bruce - Actually I'm not missing any pieces. Check out this link on the CCO to see exactly what I'm trying to accomplish: http://www.cisco.com/en/US/tech/tk652/tk701/technologies_configuration_example09186a00800ffdcc.shtml#background The router (3640,etc) utilizes the ITS feature set to act as the call manager for the network and create a small IP Key system without a few of the call manager features that I don't need in this case. And yes I want to use the 79xx phones behind the switch that I didn't mention is behind the router. I will use the FXO ports on the router to plug the incoming lines into. The page shows everything from how to do hold music to how to configure the phones XML interface. However it leaves out the PSTN setup section which is where I'm stuck at. I think I can do a session target to the ephone-dn but I'm not sure of the syntax. "Configuring the PSTN Connection on the Cisco ITS Router Assuming that the ITS router has voice interface cards, you will now want to configure those cards so that calls can be placed to and from the IP phones. This is not significantly different than other voice connections on a router. You can think of the ephones with the numbers that were assigned to the ephone-dn's as FXS ports on the routers." Thanks, Andrew On Wed, 20 Nov 2002, Bruce Enders wrote: > Andrew, > You are asking how to set something up without all the pieces necessary > to make it work. And you are describing developing a dialplan that does > not adhere to common conventions. That part is okay, you can define how > you route calls in-to and out-of your own voice network pretty much any > way you want. > The 3640 with an analog FXO is okay to act as a gateway to the PSTN. The > same router with FXS VIC ALSO will allow you to connect and originate > calls internally. However, you state you want to place "VOIP" phones on > the network behind the 3640. What "VOIP" phones would those be? If you > mean 79XX series IP Telephones from Cisco, you also need a CallManager > Server to control those phones. > As far as the dialing rules in this network, it is up to you what you use > to direct calls out to the world. Using "9" to classify all telephone > numbers that follow it as being sent to the PSTN is a convention not a > rule. The only real rule is that you have to give the system the means to > route a call based on what the User dials. AND, if you are handing the > call off to the PSTN or any other telephone switch, you have to give that > switch the call routing information (telephone number) that it needs to > route the call. > In coming calls are a whole different topic. Try reading one of the many > VoX books that are now available. > Hope this helps, > Bruce > > Andrew Dorsett wrote: > > Second call for this one. I never received any answers to my question. I > want to know how to setup the link between the VoIP phones and the FXO's. > Basically a dialplan, but how do I route inbound calls from the PSTN to > the VoIP phones? And how do I route outbound calls from the VoIP phones > over > the FXO to the PSTN? I would like to avoid a system that uses 9 to dial > an outside line. I want to do direct dialing to the PSTN without > any special steps. > > Thanks, > Andrew > > On Thu, 14 Nov 2002, Andrew Dorsett wrote: > > Hey everyone, I'm playing with an idea. I want to get ahold of a 3640 > with FXO's and interface it to the PSTN and connect to some VOIP phones > on > a network behind it. I have done all of my research on the CCO and have > found how to configure everything for phone connection and FXO > > configuration. > > However I haven't found out how to configure dialplans to dial the > outside > world. I basically need one that would say "all 4 digit dialed calls are > VoIP phones and all other numbers are outside PSTN phone numbers." And > another question that I haven't found is how to link inbound calls from > the PSTN to my VoIP phones. Say I have 555-1221 for one line and I want > it > as line 1 on my phones, and > 555-1234 as the other line on my phones. I haven't found how to map the > inbound calls to a VoIP extension. > > 555-1221 -- | || | || > | 3640 ||SWITCH|-|IP Phone| > 555-1234 -- | || | || > > My primary info source has been: > > > http://www.cisco.com/en/US/tech/tk652/tk701/technologies_configuration_example09186a00800ffdcc.shtml#ITS3660 > > Thanks, > Andrew > --- > http://www.andrewsworld.net/ICQ: 2895251 > Cisco Certified Network Associate > > "Learn from the mistakes of others. You won't live long enough to make > all > of them yourself." > > http://www.andrewsworld.net/ ICQ: 2895251 > Cisco Certified Network Associate > > "Learn from the mistakes of others. You won't live long enough to make all > of them yourself." > -- > >
Re: VoIP Question AGAIN... [7:57747]
Andrew, You are asking how to set something up without all the pieces necessary to make it work. And you are describing developing a dialplan that does not adhere to common conventions. That part is okay, you can define how you route calls in-to and out-of your own voice network pretty much any way you want. The 3640 with an analog FXO is okay to act as a gateway to the PSTN. The same router with FXS VIC ALSO will allow you to connect and originate calls internally. However, you state you want to place "VOIP" phones on the network behind the 3640. What "VOIP" phones would those be? If you mean 79XX series IP Telephones from Cisco, you also need a CallManager Server to control those phones. As far as the dialing rules in this network, it is up to you what you use to direct calls out to the world. Using "9" to classify all telephone numbers that follow it as being sent to the PSTN is a convention not a rule. The only real rule is that you have to give the system the means to route a call based on what the User dials. AND, if you are handing the call off to the PSTN or any other telephone switch, you have to give that switch the call routing information (telephone number) that it needs to route the call. In coming calls are a whole different topic. Try reading one of the many VoX books that are now available. Hope this helps, Bruce Andrew Dorsett wrote: Second call for this one. I never received any answers to my question. I want to know how to setup the link between the VoIP phones and the FXO's. Basically a dialplan, but how do I route inbound calls from the PSTN to the VoIP phones? And how do I route outbound calls from the VoIP phones over the FXO to the PSTN? I would like to avoid a system that uses 9 to dial an outside line. I want to do direct dialing to the PSTN without any special steps. Thanks, Andrew On Thu, 14 Nov 2002, Andrew Dorsett wrote: Hey everyone, I'm playing with an idea. I want to get ahold of a 3640 with FXO's and interface it to the PSTN and connect to some VOIP phones on a network behind it. I have done all of my research on the CCO and have found how to configure everything for phone connection and FXO configuration. However I haven't found out how to configure dialplans to dial the outside world. I basically need one that would say "all 4 digit dialed calls are VoIP phones and all other numbers are outside PSTN phone numbers." And another question that I haven't found is how to link inbound calls from the PSTN to my VoIP phones. Say I have 555-1221 for one line and I want it as line 1 on my phones, and 555-1234 as the other line on my phones. I haven't found how to map the inbound calls to a VoIP extension. 555-1221 -- | || | || | 3640 ||SWITCH|-|IP Phone| 555-1234 -- | || | || My primary info source has been: http://www.cisco.com/en/US/tech/tk652/tk701/technologies_configuration_example09186a00800ffdcc.shtml#ITS3660 Thanks, Andrew --- http://www.andrewsworld.net/ICQ: 2895251 Cisco Certified Network Associate "Learn from the mistakes of others. You won't live long enough to make all of them yourself." http://www.andrewsworld.net/ ICQ: 2895251 Cisco Certified Network Associate "Learn from the mistakes of others. You won't live long enough to make all of them yourself." -- Bruce Enders Email: [EMAIL PROTECTED] Chesapeake NetCraftsmeno:(410)-280-6927, c:(443)-994-0678 1290 Bay Dale Drive, Suite 312 WWW: http://www.netcraftsmen.net Arnold, MD 21012-2325 Cisco CCSI# 96047 Efax 443-331-0651 Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=57765&t=57747 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: VoIP Question AGAIN... [7:57747]
On Tue, 19 Nov 2002, Juan Blanco wrote: > Andrew > The following links will explain in full details how to accomplish what you > want Thanks, BUT...I had already found all of those URL's. They show how to create a dial plan to send the data across a "cloud" but they never show how to do it all in one device. I want to use one router as my call gateway for the entire network (no other routers because the voice gateway is internal). The URL that I sent out was a great resource and shows it can be done, but it LACKS horribly in the fact that it leaves out the crucial part of the configuration, the dial plan mapping. My confusion comes over the part where you do a session target for the incoming PSTN to VoIP calls. Do you point the session target to localhost if you are only using one router? Thanks, Andrew --- http://www.andrewsworld.net/ ICQ: 2895251 Cisco Certified Network Associate "Learn from the mistakes of others. You won't live long enough to make all of them yourself." Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=57750&t=57747 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: VoIP Question AGAIN... [7:57747]
Andrew The following links will explain in full details how to accomplish what you want Juan Blanco http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/12cgcr/voice _c/vcprt1/ http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/mult i_c/mcprt1/ http://www.cisco.com/warp/public/10/wwtraining/certprog/testing/current_exam s/9E0-423.html#examdesc -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Andrew Dorsett Sent: Tuesday, November 19, 2002 9:18 PM To: [EMAIL PROTECTED] Subject: VoIP Question AGAIN... [7:57747] Second call for this one. I never received any answers to my question. I want to know how to setup the link between the VoIP phones and the FXO's. Basically a dialplan, but how do I route inbound calls from the PSTN to the VoIP phones? And how do I route outbound calls from the VoIP phones over the FXO to the PSTN? I would like to avoid a system that uses 9 to dial an outside line. I want to do direct dialing to the PSTN without any special steps. Thanks, Andrew On Thu, 14 Nov 2002, Andrew Dorsett wrote: > Hey everyone, I'm playing with an idea. I want to get ahold of a 3640 > with FXO's and interface it to the PSTN and connect to some VOIP phones on > a network behind it. I have done all of my research on the CCO and have > found how to configure everything for phone connection and FXO configuration. > However I haven't found out how to configure dialplans to dial the outside > world. I basically need one that would say "all 4 digit dialed calls are > VoIP phones and all other numbers are outside PSTN phone numbers." And > another question that I haven't found is how to link inbound calls from > the PSTN to my VoIP phones. Say I have 555-1221 for one line and I want it > as line 1 on my phones, and > 555-1234 as the other line on my phones. I haven't found how to map the > inbound calls to a VoIP extension. > > 555-1221 -- | || | || > | 3640 ||SWITCH|-|IP Phone| > 555-1234 -- | || | || > > My primary info source has been: > http://www.cisco.com/en/US/tech/tk652/tk701/technologies_configuration_examp le09186a00800ffdcc.shtml#ITS3660 > > Thanks, > Andrew > --- > > http://www.andrewsworld.net/ > ICQ: 2895251 > Cisco Certified Network Associate > > "Learn from the mistakes of others. You won't live long enough to make all > of them yourself." http://www.andrewsworld.net/ ICQ: 2895251 Cisco Certified Network Associate "Learn from the mistakes of others. You won't live long enough to make all of them yourself." Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=57749&t=57747 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
VoIP Question AGAIN... [7:57747]
Second call for this one. I never received any answers to my question. I want to know how to setup the link between the VoIP phones and the FXO's. Basically a dialplan, but how do I route inbound calls from the PSTN to the VoIP phones? And how do I route outbound calls from the VoIP phones over the FXO to the PSTN? I would like to avoid a system that uses 9 to dial an outside line. I want to do direct dialing to the PSTN without any special steps. Thanks, Andrew On Thu, 14 Nov 2002, Andrew Dorsett wrote: > Hey everyone, I'm playing with an idea. I want to get ahold of a 3640 > with FXO's and interface it to the PSTN and connect to some VOIP phones on > a network behind it. I have done all of my research on the CCO and have > found how to configure everything for phone connection and FXO configuration. > However I haven't found out how to configure dialplans to dial the outside > world. I basically need one that would say "all 4 digit dialed calls are > VoIP phones and all other numbers are outside PSTN phone numbers." And > another question that I haven't found is how to link inbound calls from > the PSTN to my VoIP phones. Say I have 555-1221 for one line and I want it > as line 1 on my phones, and > 555-1234 as the other line on my phones. I haven't found how to map the > inbound calls to a VoIP extension. > > 555-1221 -- | || | || > | 3640 ||SWITCH|-|IP Phone| > 555-1234 -- | || | || > > My primary info source has been: > http://www.cisco.com/en/US/tech/tk652/tk701/technologies_configuration_example09186a00800ffdcc.shtml#ITS3660 > > Thanks, > Andrew > --- > > http://www.andrewsworld.net/ > ICQ: 2895251 > Cisco Certified Network Associate > > "Learn from the mistakes of others. You won't live long enough to make all > of them yourself." http://www.andrewsworld.net/ ICQ: 2895251 Cisco Certified Network Associate "Learn from the mistakes of others. You won't live long enough to make all of them yourself." Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=57747&t=57747 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
