Re: [gentoo-user] Help with Promise RAID & Gentoo [SOLVED]
OK, AT LASSTT Here's what you do to get it all working. You install as usual. Loading the ataraid module and pdcraid module. You compile your kernel with these options: ATA/IDE/MFM/RLL support ---> <*> ATA/IDE/MFM/RLL support IDE, ATA and ATAPI Block devices ---> [*] PROMISE PDC202{46|62|65|67|68|69|70} support [*] Special UDMA Feature [*] Special FastTrak Feature <*> Support for IDE Raid controllers (EXPERIMENTAL) <*>Support Promise software RAID (Fasttrak(tm)) Remember to start /boot right from the begining by formating it again. When install grub, don't do the setup (hd0) etc etc yet. Just emerge grub and then skip to the section on the howoto about making the floppy disk. Now its not a good idea to use an existing one. Create a NEW one using the commands in the howto. Then you reboot with the floppy and do: grub> root (hd0,0) // Your boot partition grub> setup (hd0) That should do it. In grub.conf you should have: title=Gentoo Linux RAID root (hd0,0) kernel /bzImage root=/dev/ataraid/disc0/part1 Thats all you need. and IT WWOOORRKKKSSS FOR ME > I've seen grub fail on SCSI RAIDS so I just went with > lilo. > > > On Thu, 5 Jun 2003 10:56:58 -0700 > [EMAIL PROTECTED] wrote: >>I gave up using grub for this, and used (groan) lilo. My >>/etc/fstab >>looks like this: >> >>/dev/ataraid/disc0/part1/boot ext2 >>noauto,noatime 1 1 >>/dev/ataraid/disc0/part3/ ext3 >>noatime 1 1 >>/dev/ataraid/disc0/part2noneswap sw >> 0 0 >>/dev/ataraid/disc0/part5/usr ext3 >> noatime 1 1 >>/dev/ataraid/disc0/part6/var ext3 >> noatime 1 2 >>/dev/ataraid/disc0/part7/usr/local ext3 >> noatime 1 2 >>/dev/ataraid/disc0/part8/opt ext3 >> noatime 1 2 >>/dev/ataraid/disc0/part9/home ext3 >> noatime 1 2 >> >>And my /etc/lilo.conf looks like this: >> >>menu-scheme=Wb >>prompt >>timeout = 50 >>lba32 >>boot=/dev/ataraid/disc0/disc >>disk = /dev/ataraid/disc0/disc >> bios = 0x80 >> >>map = /boot/System.map >>delay = 50 >>vga = normal# Normal VGA console >> >># End LILO global section >># Linux bootable partition config begins >> image = /boot/vmlinuz >> root = /dev/ataraid/disc0/part3 >> append = "idebus=66, ide0=ata66" >> label = Gentoo >> read-only # read-only for checking >> >> image = /boot/vmlinuz.old >> root = /dev/ataraid/disc0/part3 >> label = Old.kernel >> read-only # read-only for checking >> >>I hope this helps. If you find a way to make grub work, >>please let me >>know, as I would much prefer to be using grub. >> >>Cheers, >>Dennis >>-- >>Dennis Soper [EMAIL PROTECTED] >>Network Supervisor >>Facilities Services-- The University of Oregon >>1276 University of Oregon phone: 541-346-2286 >>Eugene, OR 97403 fax:541-346-2299 >> >>Voice or no voice the people can always be brought to the >>bidding of the >>leaders. That is easy. All you have to do is to tell >>them they are being >>attacked, and denounce the pacifists for lack of >>patriotism and exposing the >>country to danger. It works the same in any country. >>--Hermann >>Goering >> >> >>-- >>[EMAIL PROTECTED] mailing list >> > > > -- > [EMAIL PROTECTED] mailing list > > - Please wait while you are redirected to my signature.. -- [EMAIL PROTECTED] mailing list
RE: [gentoo-user] Help with Promise RAID & Gentoo
I would like to ask one thing tho. You have part1 as /boot and part2 as root. But i have hda1 as /boot and part1 as root. Where do you install grub? is it hda's mbr? or disc0's mbr? if it is disc0 then how to you choose that disc? did you choose in your BIOS to boot that disc first? > Re-check your kernel config, and change ur grub.conf > to your root partion: /dev/ataraid/disc0/part3 not part1 > acording to your fstab > >>> /dev/ataraid/disc0/part1/boot ext2 >>> noauto,noatime >>> 1 1 >>> /dev/ataraid/disc0/part3/ ext3 noatime >>> 1 1 > > > RNuno > > > > -Original Message- > From: MooktaKiNG [mailto:[EMAIL PROTECTED] > Sent: quinta-feira, 5 de Junho de 2003 21:17 > To: [EMAIL PROTECTED] > Subject: RE: [gentoo-user] Help with Promise RAID & Gentoo > > > Well it loads the kernel and then at the end it says there's no > ataraid/disc0/part1 and i should append it. > > But i'll try reinstalling again tonight. > >> Well my system is working :) >> >> cat /proc/pci >> >> . >> >> Bus 0, device 9, function 0: >> RAID bus controller: Promise Technology, Inc. 20268R (rev 2). >> IRQ 5. >> Master Capable. Latency=64. Min Gnt=4.Max Lat=18. >> I/O at 0xa400 [0xa407]. >> I/O at 0xa800 [0xa803]. >> I/O at 0xac00 [0xac07]. >> I/O at 0xb000 [0xb003]. >> I/O at 0xb400 [0xb40f]. >> Non-prefetchable 32 bit memory at 0xf600 [0xf600]. >> >> Anyway i have 2.4.20-gentoo-r5 kernel and i compiled >> with this options: >> >> ATA/IDE/MFM/RLL support ---> >> <*> ATA/IDE/MFM/RLL support >> IDE, ATA and ATAPI Block devices ---> >> [*] PROMISE PDC202{46|62|65|67|68|69|70} support >> [*] Special UDMA Feature >> [*] Special FastTrak Feature >> <*> Support for IDE Raid controllers (EXPERIMENTAL) >> <*>Support Promise software RAID (Fasttrak(tm)) >> (EXPERIMENTAL) >> >> So basicly i access my drives like if i used modeprobe pdcraid >> on /dev/ataraid/disc0 (for the first array) ..disc1 for the second >> array. >> >> What is the error that you are getting ? >> >> regards, >> RNuno >> >> >> >> -Original Message- >> From: MooktaKiNG [mailto:[EMAIL PROTECTED] >> Sent: quinta-feira, 5 de Junho de 2003 20:51 >> To: [EMAIL PROTECTED] >> Subject: RE: [gentoo-user] Help with Promise RAID & Gentoo >> >> >> Ricardo: >> >> I don't understand how you got it working with >> root=/dev/ataraid/disc0/part2 >> >> i thought grub excepts d0p2. weird. >> >> Did you do anything special with the kernel? >> >> Are any options you need to compile in. I mean i think i compiled >> the correct modules but, who knows. >> >> The weirdest thing is different people says different things. >> >>> hi, >>> >>> I have a PROMISE controler also and i got it to work with grub. >>> here is my config. >>> >>> /etc/fstab >>> >>> /dev/ataraid/disc0/part1/boot ext3 >>> noauto,noatime 1 1 >>> /dev/ataraid/disc0/part2/ ext3 >>> noatime >>> 0 0 >>> /dev/ataraid/disc0/part3/usrext3 >>> noatime >>> 0 0 >>> /dev/ataraid/disc0/part5/home ext3 >>> noatime >>> 0 0 >>> /dev/ataraid/disc0/part6 none swap >>> sw >>> 0 0 >>> /dev/ataraid/disc0/part7/str0 ext3 >>> noatime >>> 0 0 >>> >>> >>> /boot/grub/grub.conf >>> >>> default 0 >>> timeout 30 >>> splashimage=(hd0,0)/boot/grub/splash.xpm.gz >>> >>> title=Gentoo Linux on RAID >>> root (hd0,1) >>> kernel (hd0,0)/boot/bzImage root=/dev/ataraid/disc0/part2 >>> >>> >>> Hope it helps, lemme now if it worked for you >>> >>> RNuno >>> >>> -Original Message- >>> From: [EMAIL PROTECTED] >>> [mailto:[EMAIL PROTECTED] >>> Sent: quinta-feira, 5 de Junho de 2003 18:57 >>> To: [EMAIL PROTECTED] >>> Cc: [EMAIL PROTECTED] >>> Subject: Re: [gentoo-user] Help with Promise RAID & Gentoo >>> >>> >>> On Thu, Jun 05, 2003 at 06:54:36PM +0100, MooktaKiNG wrote
Re: [gentoo-user] Help with Promise RAID & Gentoo
I've seen grub fail on SCSI RAIDS so I just went with lilo. On Thu, 5 Jun 2003 10:56:58 -0700 [EMAIL PROTECTED] wrote: I gave up using grub for this, and used (groan) lilo. My /etc/fstab looks like this: /dev/ataraid/disc0/part1/boot ext2 noauto,noatime 1 1 /dev/ataraid/disc0/part3/ ext3 noatime 1 1 /dev/ataraid/disc0/part2noneswap sw 0 0 /dev/ataraid/disc0/part5/usr ext3 noatime 1 1 /dev/ataraid/disc0/part6/var ext3 noatime 1 2 /dev/ataraid/disc0/part7/usr/local ext3 noatime 1 2 /dev/ataraid/disc0/part8/opt ext3 noatime 1 2 /dev/ataraid/disc0/part9/home ext3 noatime 1 2 And my /etc/lilo.conf looks like this: menu-scheme=Wb prompt timeout = 50 lba32 boot=/dev/ataraid/disc0/disc disk = /dev/ataraid/disc0/disc bios = 0x80 map = /boot/System.map delay = 50 vga = normal# Normal VGA console # End LILO global section # Linux bootable partition config begins image = /boot/vmlinuz root = /dev/ataraid/disc0/part3 append = "idebus=66, ide0=ata66" label = Gentoo read-only # read-only for checking image = /boot/vmlinuz.old root = /dev/ataraid/disc0/part3 label = Old.kernel read-only # read-only for checking I hope this helps. If you find a way to make grub work, please let me know, as I would much prefer to be using grub. Cheers, Dennis -- Dennis Soper[EMAIL PROTECTED] Network Supervisor Facilities Services-- The University of Oregon 1276 University of Oregon phone: 541-346-2286 Eugene, OR 97403 fax:541-346-2299 Voice or no voice the people can always be brought to the bidding of the leaders. That is easy. All you have to do is to tell them they are being attacked, and denounce the pacifists for lack of patriotism and exposing the country to danger. It works the same in any country. --Hermann Goering -- [EMAIL PROTECTED] mailing list -- [EMAIL PROTECTED] mailing list
RE: [gentoo-user] Help with Promise RAID & Gentoo
Re-check your kernel config, and change ur grub.conf to your root partion: /dev/ataraid/disc0/part3 not part1 acording to your fstab >> /dev/ataraid/disc0/part1/boot ext2 >> noauto,noatime >> 1 1 >> /dev/ataraid/disc0/part3/ ext3 noatime >> 1 1 RNuno -Original Message- From: MooktaKiNG [mailto:[EMAIL PROTECTED] Sent: quinta-feira, 5 de Junho de 2003 21:17 To: [EMAIL PROTECTED] Subject: RE: [gentoo-user] Help with Promise RAID & Gentoo Well it loads the kernel and then at the end it says there's no ataraid/disc0/part1 and i should append it. But i'll try reinstalling again tonight. > Well my system is working :) > > cat /proc/pci > > . > > Bus 0, device 9, function 0: > RAID bus controller: Promise Technology, Inc. 20268R (rev 2). > IRQ 5. > Master Capable. Latency=64. Min Gnt=4.Max Lat=18. > I/O at 0xa400 [0xa407]. > I/O at 0xa800 [0xa803]. > I/O at 0xac00 [0xac07]. > I/O at 0xb000 [0xb003]. > I/O at 0xb400 [0xb40f]. > Non-prefetchable 32 bit memory at 0xf600 [0xf600]. > > Anyway i have 2.4.20-gentoo-r5 kernel and i compiled > with this options: > > ATA/IDE/MFM/RLL support ---> > <*> ATA/IDE/MFM/RLL support > IDE, ATA and ATAPI Block devices ---> > [*] PROMISE PDC202{46|62|65|67|68|69|70} support > [*] Special UDMA Feature > [*] Special FastTrak Feature > <*> Support for IDE Raid controllers (EXPERIMENTAL) > <*>Support Promise software RAID (Fasttrak(tm)) > (EXPERIMENTAL) > > So basicly i access my drives like if i used modeprobe pdcraid > on /dev/ataraid/disc0 (for the first array) ..disc1 for the second > array. > > What is the error that you are getting ? > > regards, > RNuno > > > > -----Original Message- > From: MooktaKiNG [mailto:[EMAIL PROTECTED] > Sent: quinta-feira, 5 de Junho de 2003 20:51 > To: [EMAIL PROTECTED] > Subject: RE: [gentoo-user] Help with Promise RAID & Gentoo > > > Ricardo: > > I don't understand how you got it working with > root=/dev/ataraid/disc0/part2 > > i thought grub excepts d0p2. weird. > > Did you do anything special with the kernel? > > Are any options you need to compile in. I mean i think i compiled > the correct modules but, who knows. > > The weirdest thing is different people says different things. > >> hi, >> >> I have a PROMISE controler also and i got it to work with grub. >> here is my config. >> >> /etc/fstab >> >> /dev/ataraid/disc0/part1/boot ext3 >> noauto,noatime 1 1 >> /dev/ataraid/disc0/part2/ ext3 >> noatime >> 0 0 >> /dev/ataraid/disc0/part3/usrext3 >> noatime >> 0 0 >> /dev/ataraid/disc0/part5/home ext3 >> noatime >> 0 0 >> /dev/ataraid/disc0/part6 none swapsw >> 0 0 >> /dev/ataraid/disc0/part7/str0 ext3 >> noatime >> 0 0 >> >> >> /boot/grub/grub.conf >> >> default 0 >> timeout 30 >> splashimage=(hd0,0)/boot/grub/splash.xpm.gz >> >> title=Gentoo Linux on RAID >> root (hd0,1) >> kernel (hd0,0)/boot/bzImage root=/dev/ataraid/disc0/part2 >> >> >> Hope it helps, lemme now if it worked for you >> >> RNuno >> >> -Original Message- >> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] >> Sent: quinta-feira, 5 de Junho de 2003 18:57 >> To: [EMAIL PROTECTED] >> Cc: [EMAIL PROTECTED] >> Subject: Re: [gentoo-user] Help with Promise RAID & Gentoo >> >> >> On Thu, Jun 05, 2003 at 06:54:36PM +0100, MooktaKiNG wrote: >> >>> OK. this is the most frustrating thing i've ever had with Gentoo. >>> >>> I can boot with the liveCD. I can load the produles, ataraid and >>> pdcraid. it does work. I install successfully. Then i install >>> Grub. >>> I follow the howto and do root=/dev/ataraid/d0p1 >>> My /boot is a seperate partition in hda1. >>> >>> But it just doesn't boot. >> >> I gave up using grub for this, and used (groan) lilo. My >> /etc/fstab >> looks like this: >> >> /dev/ataraid/disc0/part1/boot ext2 >> noauto,noatime >> 1 1 >> /dev/ataraid/disc0/part3/ ext3 noatime >> 1 1 >> /dev/ataraid/disc0/part2noneswap sw >> 0 0 >> /dev/atarai
RE: [gentoo-user] Help with Promise RAID & Gentoo
Well it loads the kernel and then at the end it says there's no ataraid/disc0/part1 and i should append it. But i'll try reinstalling again tonight. > Well my system is working :) > > cat /proc/pci > > . > > Bus 0, device 9, function 0: > RAID bus controller: Promise Technology, Inc. 20268R (rev 2). > IRQ 5. > Master Capable. Latency=64. Min Gnt=4.Max Lat=18. > I/O at 0xa400 [0xa407]. > I/O at 0xa800 [0xa803]. > I/O at 0xac00 [0xac07]. > I/O at 0xb000 [0xb003]. > I/O at 0xb400 [0xb40f]. > Non-prefetchable 32 bit memory at 0xf600 [0xf600]. > > Anyway i have 2.4.20-gentoo-r5 kernel and i compiled > with this options: > > ATA/IDE/MFM/RLL support ---> > <*> ATA/IDE/MFM/RLL support > IDE, ATA and ATAPI Block devices ---> > [*] PROMISE PDC202{46|62|65|67|68|69|70} support > [*] Special UDMA Feature > [*] Special FastTrak Feature > <*> Support for IDE Raid controllers (EXPERIMENTAL) > <*>Support Promise software RAID (Fasttrak(tm)) > (EXPERIMENTAL) > > So basicly i access my drives like if i used modeprobe pdcraid > on /dev/ataraid/disc0 (for the first array) ..disc1 for the second > array. > > What is the error that you are getting ? > > regards, > RNuno > > > > -Original Message- > From: MooktaKiNG [mailto:[EMAIL PROTECTED] > Sent: quinta-feira, 5 de Junho de 2003 20:51 > To: [EMAIL PROTECTED] > Subject: RE: [gentoo-user] Help with Promise RAID & Gentoo > > > Ricardo: > > I don't understand how you got it working with > root=/dev/ataraid/disc0/part2 > > i thought grub excepts d0p2. weird. > > Did you do anything special with the kernel? > > Are any options you need to compile in. I mean i think i compiled > the correct modules but, who knows. > > The weirdest thing is different people says different things. > >> hi, >> >> I have a PROMISE controler also and i got it to work with grub. >> here is my config. >> >> /etc/fstab >> >> /dev/ataraid/disc0/part1/boot ext3 >> noauto,noatime 1 1 >> /dev/ataraid/disc0/part2/ ext3 >> noatime >> 0 0 >> /dev/ataraid/disc0/part3/usrext3 >> noatime >> 0 0 >> /dev/ataraid/disc0/part5/home ext3 >> noatime >> 0 0 >> /dev/ataraid/disc0/part6 none swapsw >> 0 0 >> /dev/ataraid/disc0/part7/str0 ext3 >> noatime >> 0 0 >> >> >> /boot/grub/grub.conf >> >> default 0 >> timeout 30 >> splashimage=(hd0,0)/boot/grub/splash.xpm.gz >> >> title=Gentoo Linux on RAID >> root (hd0,1) >> kernel (hd0,0)/boot/bzImage root=/dev/ataraid/disc0/part2 >> >> >> Hope it helps, lemme now if it worked for you >> >> RNuno >> >> -Original Message- >> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] >> Sent: quinta-feira, 5 de Junho de 2003 18:57 >> To: [EMAIL PROTECTED] >> Cc: [EMAIL PROTECTED] >> Subject: Re: [gentoo-user] Help with Promise RAID & Gentoo >> >> >> On Thu, Jun 05, 2003 at 06:54:36PM +0100, MooktaKiNG wrote: >> >>> OK. this is the most frustrating thing i've ever had with Gentoo. >>> >>> I can boot with the liveCD. I can load the produles, ataraid and >>> pdcraid. it does work. I install successfully. Then i install >>> Grub. >>> I follow the howto and do root=/dev/ataraid/d0p1 >>> My /boot is a seperate partition in hda1. >>> >>> But it just doesn't boot. >> >> I gave up using grub for this, and used (groan) lilo. My >> /etc/fstab >> looks like this: >> >> /dev/ataraid/disc0/part1/boot ext2 >> noauto,noatime >> 1 1 >> /dev/ataraid/disc0/part3/ ext3 noatime >> 1 1 >> /dev/ataraid/disc0/part2noneswap sw >> 0 0 >> /dev/ataraid/disc0/part5/usr ext3noatime >> 1 1 >> /dev/ataraid/disc0/part6/var ext3noatime >> 1 2 >> /dev/ataraid/disc0/part7/usr/local ext3noatime >> 1 >> 2 >> /dev/ataraid/disc0/part8/opt ext3noatime >> 1 2 >> /dev/ataraid/disc0/part9/home ext3noatime >> 1 2 >> >> And my /etc/lilo.conf looks like this: >> >> menu-scheme=Wb >> pr
RE: [gentoo-user] Help with Promise RAID & Gentoo
Well my system is working :) cat /proc/pci . Bus 0, device 9, function 0: RAID bus controller: Promise Technology, Inc. 20268R (rev 2). IRQ 5. Master Capable. Latency=64. Min Gnt=4.Max Lat=18. I/O at 0xa400 [0xa407]. I/O at 0xa800 [0xa803]. I/O at 0xac00 [0xac07]. I/O at 0xb000 [0xb003]. I/O at 0xb400 [0xb40f]. Non-prefetchable 32 bit memory at 0xf600 [0xf600]. Anyway i have 2.4.20-gentoo-r5 kernel and i compiled with this options: ATA/IDE/MFM/RLL support ---> <*> ATA/IDE/MFM/RLL support IDE, ATA and ATAPI Block devices ---> [*] PROMISE PDC202{46|62|65|67|68|69|70} support [*] Special UDMA Feature [*] Special FastTrak Feature <*> Support for IDE Raid controllers (EXPERIMENTAL) <*>Support Promise software RAID (Fasttrak(tm)) (EXPERIMENTAL) So basicly i access my drives like if i used modeprobe pdcraid on /dev/ataraid/disc0 (for the first array) ..disc1 for the second array. What is the error that you are getting ? regards, RNuno -Original Message- From: MooktaKiNG [mailto:[EMAIL PROTECTED] Sent: quinta-feira, 5 de Junho de 2003 20:51 To: [EMAIL PROTECTED] Subject: RE: [gentoo-user] Help with Promise RAID & Gentoo Ricardo: I don't understand how you got it working with root=/dev/ataraid/disc0/part2 i thought grub excepts d0p2. weird. Did you do anything special with the kernel? Are any options you need to compile in. I mean i think i compiled the correct modules but, who knows. The weirdest thing is different people says different things. > hi, > > I have a PROMISE controler also and i got it to work with grub. > here is my config. > > /etc/fstab > > /dev/ataraid/disc0/part1/boot ext3 > noauto,noatime 1 1 > /dev/ataraid/disc0/part2/ ext3 > noatime > 0 0 > /dev/ataraid/disc0/part3/usrext3 > noatime > 0 0 > /dev/ataraid/disc0/part5/home ext3 > noatime > 0 0 > /dev/ataraid/disc0/part6 none swapsw > 0 0 > /dev/ataraid/disc0/part7/str0 ext3 > noatime > 0 0 > > > /boot/grub/grub.conf > > default 0 > timeout 30 > splashimage=(hd0,0)/boot/grub/splash.xpm.gz > > title=Gentoo Linux on RAID > root (hd0,1) > kernel (hd0,0)/boot/bzImage root=/dev/ataraid/disc0/part2 > > > Hope it helps, lemme now if it worked for you > > RNuno > > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] > Sent: quinta-feira, 5 de Junho de 2003 18:57 > To: [EMAIL PROTECTED] > Cc: [EMAIL PROTECTED] > Subject: Re: [gentoo-user] Help with Promise RAID & Gentoo > > > On Thu, Jun 05, 2003 at 06:54:36PM +0100, MooktaKiNG wrote: > >> OK. this is the most frustrating thing i've ever had with Gentoo. >> >> I can boot with the liveCD. I can load the produles, ataraid and >> pdcraid. it does work. I install successfully. Then i install >> Grub. >> I follow the howto and do root=/dev/ataraid/d0p1 >> My /boot is a seperate partition in hda1. >> >> But it just doesn't boot. > > I gave up using grub for this, and used (groan) lilo. My /etc/fstab > looks like this: > > /dev/ataraid/disc0/part1/boot ext2 noauto,noatime > 1 1 > /dev/ataraid/disc0/part3/ ext3 noatime > 1 1 > /dev/ataraid/disc0/part2noneswap sw > 0 0 > /dev/ataraid/disc0/part5/usr ext3noatime > 1 1 > /dev/ataraid/disc0/part6/var ext3noatime > 1 2 > /dev/ataraid/disc0/part7/usr/local ext3noatime > 1 > 2 > /dev/ataraid/disc0/part8/opt ext3noatime > 1 2 > /dev/ataraid/disc0/part9/home ext3noatime > 1 2 > > And my /etc/lilo.conf looks like this: > > menu-scheme=Wb > prompt > timeout = 50 > lba32 > boot=/dev/ataraid/disc0/disc > disk = /dev/ataraid/disc0/disc > bios = 0x80 > > map = /boot/System.map > delay = 50 > vga = normal# Normal VGA console > # End LILO global section > # Linux bootable partition config begins > image = /boot/vmlinuz > root = /dev/ataraid/disc0/part3 > append = "idebus=66, ide0=ata66" > label = Gentoo > read-only # read-only for checking > > image = /boot/vmlinuz.old > root = /dev/ataraid/disc0/part3 > label = Old.kernel > read-only # read-only for checking > > I hope this helps. If you find a way to make grub work, please let > me > know, as I would much prefer to be using g
RE: [gentoo-user] Help with Promise RAID & Gentoo
Ricardo: I don't understand how you got it working with root=/dev/ataraid/disc0/part2 i thought grub excepts d0p2. weird. Did you do anything special with the kernel? Are any options you need to compile in. I mean i think i compiled the correct modules but, who knows. The weirdest thing is different people says different things. > hi, > > I have a PROMISE controler also and i got it to work with grub. > here is my config. > > /etc/fstab > > /dev/ataraid/disc0/part1/boot ext3 > noauto,noatime 1 1 > /dev/ataraid/disc0/part2/ ext3 > noatime > 0 0 > /dev/ataraid/disc0/part3/usrext3 > noatime > 0 0 > /dev/ataraid/disc0/part5/home ext3 > noatime > 0 0 > /dev/ataraid/disc0/part6 none swapsw > 0 0 > /dev/ataraid/disc0/part7/str0 ext3 > noatime > 0 0 > > > /boot/grub/grub.conf > > default 0 > timeout 30 > splashimage=(hd0,0)/boot/grub/splash.xpm.gz > > title=Gentoo Linux on RAID > root (hd0,1) > kernel (hd0,0)/boot/bzImage root=/dev/ataraid/disc0/part2 > > > Hope it helps, lemme now if it worked for you > > RNuno > > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] > Sent: quinta-feira, 5 de Junho de 2003 18:57 > To: [EMAIL PROTECTED] > Cc: [EMAIL PROTECTED] > Subject: Re: [gentoo-user] Help with Promise RAID & Gentoo > > > On Thu, Jun 05, 2003 at 06:54:36PM +0100, MooktaKiNG wrote: > >> OK. this is the most frustrating thing i've ever had with Gentoo. >> >> I can boot with the liveCD. I can load the produles, ataraid and >> pdcraid. it does work. I install successfully. Then i install >> Grub. >> I follow the howto and do root=/dev/ataraid/d0p1 >> My /boot is a seperate partition in hda1. >> >> But it just doesn't boot. > > I gave up using grub for this, and used (groan) lilo. My /etc/fstab > looks like this: > > /dev/ataraid/disc0/part1/boot ext2 noauto,noatime > 1 1 > /dev/ataraid/disc0/part3/ ext3 noatime > 1 1 > /dev/ataraid/disc0/part2noneswap sw > 0 0 > /dev/ataraid/disc0/part5/usr ext3noatime > 1 1 > /dev/ataraid/disc0/part6/var ext3noatime > 1 2 > /dev/ataraid/disc0/part7/usr/local ext3noatime > 1 > 2 > /dev/ataraid/disc0/part8/opt ext3noatime > 1 2 > /dev/ataraid/disc0/part9/home ext3noatime > 1 2 > > And my /etc/lilo.conf looks like this: > > menu-scheme=Wb > prompt > timeout = 50 > lba32 > boot=/dev/ataraid/disc0/disc > disk = /dev/ataraid/disc0/disc > bios = 0x80 > > map = /boot/System.map > delay = 50 > vga = normal# Normal VGA console > # End LILO global section > # Linux bootable partition config begins > image = /boot/vmlinuz > root = /dev/ataraid/disc0/part3 > append = "idebus=66, ide0=ata66" > label = Gentoo > read-only # read-only for checking > > image = /boot/vmlinuz.old > root = /dev/ataraid/disc0/part3 > label = Old.kernel > read-only # read-only for checking > > I hope this helps. If you find a way to make grub work, please let > me > know, as I would much prefer to be using grub. > > Cheers, > Dennis > -- > Dennis Soper [EMAIL PROTECTED] > Network Supervisor > Facilities Services-- The University of Oregon > 1276 University of Oregon phone: 541-346-2286 > Eugene, OR 97403 fax:541-346-2299 > > Voice or no voice the people can always be brought to the bidding of > the > leaders. That is easy. All you have to do is to tell them they are > being > attacked, and denounce the pacifists for lack of patriotism and > exposing the > country to danger. It works the same in any country. >--Hermann Goering > > > -- > [EMAIL PROTECTED] mailing list > > > > -- > [EMAIL PROTECTED] mailing list > > - Please wait while you are redirected to my signature.. -- [EMAIL PROTECTED] mailing list
RE: [gentoo-user] Help with Promise RAID & Gentoo
hi, I have a PROMISE controler also and i got it to work with grub. here is my config. /etc/fstab /dev/ataraid/disc0/part1/boot ext3 noauto,noatime 1 1 /dev/ataraid/disc0/part2/ ext3noatime 0 0 /dev/ataraid/disc0/part3/usrext3noatime 0 0 /dev/ataraid/disc0/part5/home ext3noatime 0 0 /dev/ataraid/disc0/part6 none swapsw 0 0 /dev/ataraid/disc0/part7/str0 ext3noatime 0 0 /boot/grub/grub.conf default 0 timeout 30 splashimage=(hd0,0)/boot/grub/splash.xpm.gz title=Gentoo Linux on RAID root (hd0,1) kernel (hd0,0)/boot/bzImage root=/dev/ataraid/disc0/part2 Hope it helps, lemme now if it worked for you RNuno -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Sent: quinta-feira, 5 de Junho de 2003 18:57 To: [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Subject: Re: [gentoo-user] Help with Promise RAID & Gentoo On Thu, Jun 05, 2003 at 06:54:36PM +0100, MooktaKiNG wrote: > OK. this is the most frustrating thing i've ever had with Gentoo. > > I can boot with the liveCD. I can load the produles, ataraid and > pdcraid. it does work. I install successfully. Then i install Grub. > I follow the howto and do root=/dev/ataraid/d0p1 > My /boot is a seperate partition in hda1. > > But it just doesn't boot. I gave up using grub for this, and used (groan) lilo. My /etc/fstab looks like this: /dev/ataraid/disc0/part1/boot ext2 noauto,noatime 1 1 /dev/ataraid/disc0/part3/ ext3 noatime 1 1 /dev/ataraid/disc0/part2noneswap sw 0 0 /dev/ataraid/disc0/part5/usr ext3noatime 1 1 /dev/ataraid/disc0/part6/var ext3noatime 1 2 /dev/ataraid/disc0/part7/usr/local ext3noatime 1 2 /dev/ataraid/disc0/part8/opt ext3noatime 1 2 /dev/ataraid/disc0/part9/home ext3noatime 1 2 And my /etc/lilo.conf looks like this: menu-scheme=Wb prompt timeout = 50 lba32 boot=/dev/ataraid/disc0/disc disk = /dev/ataraid/disc0/disc bios = 0x80 map = /boot/System.map delay = 50 vga = normal# Normal VGA console # End LILO global section # Linux bootable partition config begins image = /boot/vmlinuz root = /dev/ataraid/disc0/part3 append = "idebus=66, ide0=ata66" label = Gentoo read-only # read-only for checking image = /boot/vmlinuz.old root = /dev/ataraid/disc0/part3 label = Old.kernel read-only # read-only for checking I hope this helps. If you find a way to make grub work, please let me know, as I would much prefer to be using grub. Cheers, Dennis -- Dennis Soper[EMAIL PROTECTED] Network Supervisor Facilities Services-- The University of Oregon 1276 University of Oregon phone: 541-346-2286 Eugene, OR 97403 fax:541-346-2299 Voice or no voice the people can always be brought to the bidding of the leaders. That is easy. All you have to do is to tell them they are being attacked, and denounce the pacifists for lack of patriotism and exposing the country to danger. It works the same in any country. --Hermann Goering -- [EMAIL PROTECTED] mailing list -- [EMAIL PROTECTED] mailing list
Re: [gentoo-user] Help with Promise RAID & Gentoo
On Thu, Jun 05, 2003 at 06:54:36PM +0100, MooktaKiNG wrote: > OK. this is the most frustrating thing i've ever had with Gentoo. > > I can boot with the liveCD. I can load the produles, ataraid and > pdcraid. it does work. I install successfully. Then i install Grub. > I follow the howto and do root=/dev/ataraid/d0p1 > My /boot is a seperate partition in hda1. > > But it just doesn't boot. I gave up using grub for this, and used (groan) lilo. My /etc/fstab looks like this: /dev/ataraid/disc0/part1/boot ext2 noauto,noatime 1 1 /dev/ataraid/disc0/part3/ ext3 noatime 1 1 /dev/ataraid/disc0/part2noneswap sw 0 0 /dev/ataraid/disc0/part5/usr ext3noatime 1 1 /dev/ataraid/disc0/part6/var ext3noatime 1 2 /dev/ataraid/disc0/part7/usr/local ext3noatime 1 2 /dev/ataraid/disc0/part8/opt ext3noatime 1 2 /dev/ataraid/disc0/part9/home ext3noatime 1 2 And my /etc/lilo.conf looks like this: menu-scheme=Wb prompt timeout = 50 lba32 boot=/dev/ataraid/disc0/disc disk = /dev/ataraid/disc0/disc bios = 0x80 map = /boot/System.map delay = 50 vga = normal# Normal VGA console # End LILO global section # Linux bootable partition config begins image = /boot/vmlinuz root = /dev/ataraid/disc0/part3 append = "idebus=66, ide0=ata66" label = Gentoo read-only # read-only for checking image = /boot/vmlinuz.old root = /dev/ataraid/disc0/part3 label = Old.kernel read-only # read-only for checking I hope this helps. If you find a way to make grub work, please let me know, as I would much prefer to be using grub. Cheers, Dennis -- Dennis Soper[EMAIL PROTECTED] Network Supervisor Facilities Services-- The University of Oregon 1276 University of Oregon phone: 541-346-2286 Eugene, OR 97403 fax:541-346-2299 Voice or no voice the people can always be brought to the bidding of the leaders. That is easy. All you have to do is to tell them they are being attacked, and denounce the pacifists for lack of patriotism and exposing the country to danger. It works the same in any country. --Hermann Goering -- [EMAIL PROTECTED] mailing list
RE: [gentoo-user] Help with Promise RAID & Gentoo
->-Original Message- ->From: MooktaKiNG [mailto:[EMAIL PROTECTED] ->Sent: Thursday, June 05, 2003 1:55 PM ->To: [EMAIL PROTECTED] ->Subject: [gentoo-user] Help with Promise RAID & Gentoo -> -> ->OK. this is the most frustrating thing i've ever had with Gentoo. -> ->I can boot with the liveCD. I can load the produles, ataraid and ->pdcraid. it does work. I install successfully. Then i install Grub. ->I follow the howto and do root=/dev/ataraid/d0p1 ->My /boot is a seperate partition in hda1. -> ->But it just doesn't boot. -> ->Grub does not know what /dev/ataraid/d0p1 is. To it it doesn't work. -> ->My hd's are: -> ->hda= 40Gb HD use it for this and that. /boot is loacted here. ->hdb= My backup HD and i also usually have swap here ->hde & hdg= Raid striping. each is a 20Gb ATA100 drives. -> ->In BIOS hda is the first to boot. -> ->My raid is partitioned: -> ->hda1 is /boot ->disc0/part1 as root ->disc0/part5 is swap -> ->I know a LOT of people have got this working. -> ->I tried everything that i found in gentoo's forum ->Without any luck. -> ->Its just Grub. thats whats making me very angry. I spent numerous hours last weekend trying to get gentoo to boot completely from a promise raid also. It saw the bood drive and started the kernel just fine finally, but I could never get it past the root filesystem. kernel panic every time. tried both gentoo and ac sources etc. I finally gave up, put everything on the regular ide channel, then mounted the raide after the fact. kev -- [EMAIL PROTECTED] mailing list