Very many thanks to everyone who responded to my request for help. Happily
the fault turned out to be something very simple. Rob at Elecraft suggested
the LPA FETs may have failed as the current measurements I had taken
indicated the FETs were not drawing the bias current they should be. I
checked
Check that TX INHIBIT is off in the menu.
Victor 4X6GP
> On 16 Jun 2020, at 0:35, G4BVH wrote:
>
>
>
>
>
>
>Hi Bill,The rig doesnot produce any RF out in any mode. Everything
> looks normal on the display, LEDs etc, the rig keys via mic or paddle but
> just no RF.Some have sugg
Hi Bill,The rig does not produce any RF out in any mode. Everything
looks normal on the display, LEDs etc, the rig keys via mic or paddle but just
no RF.Some have suggested a bad internal cable connection or bad board edge
connector. I am working my way through those. 73,
DOES k3 xmit ssb with a mic in usb ?
what mode ( TXDATA) are you using ...
usually when I have that symptom, turns out that computer sound card is
NOT putting out TX audio to rig.
On 6/15/2020 4:04 AM, G4BVH wrote:
Hi,
I have had a fault develop on my K3 whereby there is no RF being p
On 6/15/2020 1:10 AM, Dick Dievendorff wrote:
Is TX test on?
73 de Dick, K6KR
On Jun 15, 2020, at 01:06, G4BVH wrote:
Hi,
I have had a fault develop on my K3 whereby there is no RF being produced. I
have emailed the details to Elecraft support and am hoping to receive a
reply with sugges
I had a problem with no output, but the radio was keying. I reseated all
cables going to the synthesizer, and rf output returned.
73, Will, wj9b
CWops #1085
CWA Advisor levels II and III
http://cwops.org/
On Monday, June 15, 2020, 01:04:50 AM PDT, G4BVH
wrote:
Hi,
I have had a
Is TX test on?
73 de Dick, K6KR
> On Jun 15, 2020, at 01:06, G4BVH wrote:
>
> Hi,
>
>
>
> I have had a fault develop on my K3 whereby there is no RF being produced. I
> have emailed the details to Elecraft support and am hoping to receive a
> reply with suggestions. However, I thought I wou
Hi,
I have had a fault develop on my K3 whereby there is no RF being produced. I
have emailed the details to Elecraft support and am hoping to receive a
reply with suggestions. However, I thought I would also send the details
here in case anyone can suggest something to try or investigate furth
Check your TMP cable connections.
Sent from Mail for Windows 10
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hoste
Hello Readers,
i need to understand which point in the signal path i have to control/measure
to investigate further damages in my K3 after water damage event.
yes, VOX is on.
When i have the place where the issue starts, i want to understand what is
causing that behavior.
Currently receiver is wo
Is VOX On?
Sent from my iPhone
...nr4c. bill
> On Jul 21, 2019, at 2:32 PM, Harald Fritzsche wrote:
>
> Dear Readers,
>
> i made a water damage of my K3. Meanwhile Receiver is working again, after
> some repairs.
>
> But there is still no RF output.
>
> Main symptom is, that in case of TX
Dear Readers,
i made a water damage of my K3. Meanwhile Receiver is working again, after some
repairs.
But there is still no RF output.
Main symptom is, that in case of TX (key down in CW) i find at J7 (8.215 MHz
TXIF1) a 8.230MHz signal, but no signal passing the filter, expected
approxymate
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Gregg
W6IZT
Sent: Sunday, November 9, 2014 1:15 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 No RF output
I am getting 0 RF output from my K3 on all bands regardless of the commanded
power leve
-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Gregg
W6IZT
Sent: Sunday, November 9, 2014 1:15 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 No RF output
I am getting 0 RF output from my K3 on all bands regardless of the commanded
power level. Pressing the TX button
It means TX Inh(ibit) has been activated. Check your menu setting.
73,
Rick, WA6NHC
iPad = small keypad = typos = sorry ;-)
> On Nov 9, 2014, at 10:14 AM, Gregg W6IZT wrote:
>
> I am getting 0 RF output from my K3 on all bands regardless of the commanded
> power level. Pressing the TX button
I am getting 0 RF output from my K3 on all bands regardless of the commanded
power level. Pressing the TX button results in -- where the SWR would
normally be displayed.
Any suggestions or ideas on how to resolve this issue are greatly
appreciated.
Thanks
Gregg w6izt
n but as stated now there is no RF being produced at all. Thanks
again and it looks like a trip to Elecraft for the K3.
Todd
-Original Message-
From: Jim N7US
Sent: Sunday, April 29, 2012 9:09 AM
To: 'Elecraft List'
Cc: 'Gary Surrency'
Subject: Re: [Elecraft]
Todd,
I experienced the same problem a couple of months ago. I never noticed a
fault, but maybe it did it, and I didn't notice.
I emailed Gary (supp...@elecraft.com) and tried the EE INIT including
reloading previously saved configurations. I ended up sending the radio
(S/N 3598) in. Keith fou
18 matches
Mail list logo
