[Flexradio] Hearing a very brief bust of audio from adjacent frequency signal when tuning with mouse wheel.

I am hearing a strange phenomenon when tuning with the mouse wheel on my Flex 5000A with PSDR v1.10.4. While listening on a quiet 20m SSB frequency for example if I rock the mouse wheel back and forth slowly just one click I can hear a very brief burst of audio from a relatively strong (S7 or more

[Flexradio] W2RF PowerSDR I/Q "problem"

Ed, Thanks for your patience with my W2RF PowerSDR I/Q questions. All, the problem I reported with Ed's console sending I/Q to CW Skimmer was a user error. I failed to read the documentation (in CW Skimmer Help) that clearly states that the W2RF version of the PowerSDR application only supports

[Flexradio] 160 meter arcing

I am experiencing an internal arcing/frying sound from inside the 5000a on 160 meters anytime the RF power gets above 50 watts on any mode. This has occurred since day on one my 5000. It occurs on all antenna ports and both of my 160 meter antennas (shunt fed tower and inverted Vee) as well as my

[Flexradio] 6 meters

Plil, I work a station in Ohio (W8IF) daily from my QTH in Southwest Florida, (950 mile path) seven days a week on a schedule. I use an SDR5000, a HB 6 meter amplifier (1000 watts) and a good 6 meter yagi. I also use an Advance Receiver Research 6 meter receiver preamp. ($80) With the BNC RX1 I

[Flexradio] 6 meter performance

Disheartening comments by Joel, W5ZN (although he didn't intend it so...just honest candor). The Ft-920 is over 10 years old and is on the used market for about $800 or so. These are not off the wall opinions from just another crackpot. Check out his credentials on QRZ. I would have hoped for bette

Re: [Flexradio] 6 meters

I hope you were listening this morning. Six was open in the CO-IA-MN direction from my QTH (EM00xb) and some of the beacon signals were 599. I worked several stations with signals ranging from S3 to S9 using a three element beam at 50 feet. Bob K5KDN -Original Message- From: [EMAIL PROT

[Flexradio] 2008/May/24 FRF TeamSpeak audio

The 24/May Flex Radio Friends TeamSpeak zipped mp3 (1 hour 15 minutes) plus a text file of channel comments is available at: < http://www.hamsdr.com/dnld.aspx?id=805 > or < http://www.hamsdr.com/dnld.aspx > Post-Dayton and power supply horror stories. I am still experiencing dropouts about

Re: [Flexradio] FlexRadio Digest, Vol 37, Issue 24

Six Meters on the Flex 5000 For those who have complained about 6 meter reception the on the 5K, I experienced a similar situation. I won't say it was real bad, but it wasn't quite as good as my old IC-756 Pro II which I sold soon after acquiring the 5K. Checking with a beacon abt 80 miles away

Re: [Flexradio] TV signals and 6 meters

Check this URL for a guide to TV sigs near you. http://www.w9wi.com/tvdb/natv.htm The audio carrier for KDKA channel 2 on 55.74 MHz is 10 over S-9 into my SDR-1000 connected to my vertical antenna. SWR is about 7:1. I'm about 20 miles away from their antenna, as the Crow flies... > Message

Re: [Flexradio] Direct I/Q output for CW Skimmer

Ed, I'm sure I'm misunderstanding something... and I appreciate your patience. When I send the output to VAC as I change modes on PowerSDR, the CW Skimmer waterfall changes. When I change the filters in PowerSDR, then the waterfall in CW skimmer only shows signals in a narrow band (as wide as t

Re: [Flexradio] Direct I/Q output for CW Skimmer

Hi Mark, If VAC output is set up properly Skimmer will process the entire sampled spectrum of 48, 96, or 192khz. There is no need to do any special filter setup. The demod audio continues as normal. For example, while I am processing 96khz of spectrum into Skimmer, I am running PowerSDR with

Re: [Flexradio] 6 meters

I can answer my own question upon closer examination. Only the transmit antenna is fixed to ANT 3, the receive antenna can be selected to any of them. 73 Self -Original Message- From: Ross Stenberg [mailto:[EMAIL PROTECTED] Sent: Saturday, May 24, 2008 4:51 AM To: 'Dudley Hurry'

[Flexradio] FW: Direct I/Q output for CW Skimmer

Ed W2RF Thanks for building in the VAC I/Q output into your branch! I've been using it this morning, and it's really fun to watch the contest in progress. In order to use it I had to make some changes to the the CW Pitch and Audio IF in CW Skimmer (version 1.1) to get the display to line up wit

Re: [Flexradio] 6 meters

Why is it that my SDR-5000 receives 6 meters fine on ANT 1 or ANT 3? Will it only transmit on ANT 3? I of course used the antenna control tab to switch between them. 73 Ross K9COX -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Dudley Hurry Sent