Re: [Asterisk-Users] Fedora Core 4 not recognizing X100P cards
como'n folks.. ... Well, as I told earlier.. my asterisk was running great with one fxo and one fxs module of a TDM400P All i tried last night to run asterisk with non-root I must did something wrong while I was trying to do that FXO module on channel # 1 FXS module on channel # 4 /etc/zaptel.conf - loadzone = us defaultzone=us fxoks=1 fxsks=4 /etc/asterisk/zapata.conf signalling=fxo_ks channel=1 signalling=fxs_ks channel=4 Did I made any mistake above? /etc/modprobe.conf - install wcfxo /sbin/modprobe --ignore-install wcfxo /sbin/ztcfg install wctdm /sbin/modprobe --ignore-install wctdm /sbin/ztcfg # there have more line in it.. i guess they are not important here alias wcfxs wctdm /etc/rc.d/init.d/asterisk - #important lines are below start) /sbin/modprobe wctdm daemon /usr/sbin/asterisk stop) killproc asterisk /sbin/modprobe -r wctdm Here is the output of asterisk -vvvc Sep 13 22:18:11 WARNING[3982]: chan_zap.c:887 zt_open: Unable to specify channel 1: No such device Sep 13 22:18:11 ERROR[3982]: chan_zap.c:6612 mkintf: Unable to open channel 1: No such device here = 0, tmp-channel = 1, channel = 1 Sep 13 22:18:11 ERROR[3982]: chan_zap.c:9990 setup_zap: Unable to register channel '1' Sep 13 22:18:11 WARNING[3982]: loader.c:403 __load_resource: chan_zap.so: load_module failed, returning -1 Sep 13 22:18:11 WARNING[3982]: loader.c:543 load_modules: Loading module chan_zap.so failed! see I have channel # 1 [EMAIL PROTECTED] ~]# ls -l /dev/zap/ total 0 crw-rw 1 root asterisk 196, 1 Sep 13 22:20 1 crw-rw 1 root asterisk 196, 2 Sep 13 22:20 2 crw-rw 1 root asterisk 196, 3 Sep 13 22:20 3 crw-rw 1 root asterisk 196, 4 Sep 13 22:20 4 crw-rw 1 root asterisk 196, 254 Sep 13 22:20 channel crw-rw 1 root asterisk 196, 0 Sep 13 22:20 ctl crw-rw 1 root asterisk 196, 255 Sep 13 22:20 pseudo crw-rw 1 root asterisk 196, 253 Sep 13 22:20 timer After all of this, if I comment out this from /etc/asterisk/zapata.conf /etc/asterisk/zapata.conf ;signalling=fxo_ks ;channel=1 signalling=fxs_ks channel=4 My asterisk run fine .. I just dont able to use my phone set attaced to my fxs module. And all I had to do is .. forward all incoming call to my voicemail box !! Should I consider my fxs card has burnt out !! Thanks for reading.. hope someone will reply me to help. Thanks again, ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] Fedora Core 4 not recognizing X100P cards
On Tue, Sep 13, 2005 at 12:01:21PM -0800, Mojo with Horan Company, LLC wrote: hisax seems to be a loadable module for an ISDN card. if: # lsmod | grep hisax prints any output, try # rmmod hisax; modprobe zaptel What information does kudzu use? Why doesn't it know that those PCI IDs are used for zaptel as well? Doesn't it update its modules information from the installed modules? Also: isn't there a simple way to load some modules in andvance and/or blacklist others? (/etc/modules and /etc/hotplug/blacklist , respectively on debian). -- Tzafrir Cohen | [EMAIL PROTECTED] | VIM is http://tzafrir.org.il | | a Mutt's [EMAIL PROTECTED] | | best ICQ# 16849755 | | friend ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] Fedora Core 4 not recognizing X100P cards
just an update for all curious folks I just replaced my FXS card and everything is working great .. I am running asterisk as non-root user. Moreover, I couldn't figure it out how/why my FXS card got damaged. Thanks, -Original Message- From: [EMAIL PROTECTED] Sent: Wed, 14 Sep 2005 06:44:45 -0800 To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Fedora Core 4 not recognizing X100P cards como'n folks.. ... Well, as I told earlier.. my asterisk was running great with one fxo and one fxs module of a TDM400P All i tried last night to run asterisk with non-root I must did something wrong while I was trying to do that FXO module on channel # 1 FXS module on channel # 4 /etc/zaptel.conf - loadzone = us defaultzone=us fxoks=1 fxsks=4 /etc/asterisk/zapata.conf signalling=fxo_ks channel=1 signalling=fxs_ks channel=4 Did I made any mistake above? /etc/modprobe.conf - install wcfxo /sbin/modprobe --ignore-install wcfxo /sbin/ztcfg install wctdm /sbin/modprobe --ignore-install wctdm /sbin/ztcfg # there have more line in it.. i guess they are not important here alias wcfxs wctdm /etc/rc.d/init.d/asterisk - #important lines are below start) /sbin/modprobe wctdm daemon /usr/sbin/asterisk stop) killproc asterisk /sbin/modprobe -r wctdm Here is the output of asterisk -vvvc Sep 13 22:18:11 WARNING[3982]: chan_zap.c:887 zt_open: Unable to specify channel 1: No such device Sep 13 22:18:11 ERROR[3982]: chan_zap.c:6612 mkintf: Unable to open channel 1: No such device here = 0, tmp-channel = 1, channel = 1 Sep 13 22:18:11 ERROR[3982]: chan_zap.c:9990 setup_zap: Unable to register channel '1' Sep 13 22:18:11 WARNING[3982]: loader.c:403 __load_resource: chan_zap.so: load_module failed, returning -1 Sep 13 22:18:11 WARNING[3982]: loader.c:543 load_modules: Loading module chan_zap.so failed! see I have channel # 1 [EMAIL PROTECTED] ~]# ls -l /dev/zap/ total 0 crw-rw 1 root asterisk 196, 1 Sep 13 22:20 1 crw-rw 1 root asterisk 196, 2 Sep 13 22:20 2 crw-rw 1 root asterisk 196, 3 Sep 13 22:20 3 crw-rw 1 root asterisk 196, 4 Sep 13 22:20 4 crw-rw 1 root asterisk 196, 254 Sep 13 22:20 channel crw-rw 1 root asterisk 196, 0 Sep 13 22:20 ctl crw-rw 1 root asterisk 196, 255 Sep 13 22:20 pseudo crw-rw 1 root asterisk 196, 253 Sep 13 22:20 timer After all of this, if I comment out this from /etc/asterisk/zapata.conf /etc/asterisk/zapata.conf ;signalling=fxo_ks ;channel=1 signalling=fxs_ks channel=4 My asterisk run fine .. I just dont able to use my phone set attaced to my fxs module. And all I had to do is .. forward all incoming call to my voicemail box !! Should I consider my fxs card has burnt out !! Thanks for reading.. hope someone will reply me to help. Thanks again, ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
[Asterisk-Users] Fedora Core 4 not recognizing X100P cards
I am getting quite frustrated today, so please bear with me. I just installed Fedora Core 4 (was running RedHat 9 with a working Asterisk) now my Fedora does not appear to be recognizing my X100P (clone) at all. Hardware browser just shows them as unknown device. driver: hisax So, of course, my zaptel drivers do not work and therefore my asterisk does not work. any help would be greatly appreciated.. Shawn ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] Fedora Core 4 not recognizing X100P cards
hisax seems to be a loadable module for an ISDN card. if: # lsmod | grep hisax prints any output, try # rmmod hisax; modprobe zaptel ? hth Mojo Shawn Porter wrote: I am getting quite frustrated today, so please bear with me. I just installed Fedora Core 4 (was running RedHat 9 with a working Asterisk) now my Fedora does not appear to be recognizing my X100P (clone) at all. Hardware browser just shows them as unknown device. driver: hisax So, of course, my zaptel drivers do not work and therefore my asterisk does not work. any help would be greatly appreciated….. Shawn ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- Mojo [EMAIL PROTECTED] Office Manger, Horan Company, LLC (907) 747- x112 ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] Fedora Core 4 not recognizing X100P cards
I have the same problem. I've been having a bit of trouble getting the cards to work with asterisk, and I thought perhaps you might know what I might be doing wrong. I installed them in a linux box, and when I check to see if the OS has recognized them it looks fine: They show up as HSP56 MicroModem (rev 04) [EMAIL PROTECTED] lspci 00:00.0 Host bridge: Intel Corporation 82850 850 (Tehama) Chipset Host Bridge (MCH) (rev 04) 00:01.0 PCI bridge: Intel Corporation 82850 850 (Tehama) Chipset AGP Bridge (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 04) 00:1f.0 ISA bridge: Intel Corporation 82801BA ISA Bridge (LPC) (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801BA IDE U100 (rev 04) 00:1f.2 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #1) (rev 04) 00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus (rev 04) 00:1f.5 Multimedia audio controller: Intel Corporation 82801BA/BAM AC'97 Audio (rev 04) 01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 4000 AGP 8x] (rev c1) 02:01.0 USB Controller: NEC Corporation USB (rev 41) 02:01.1 USB Controller: NEC Corporation USB (rev 41) 02:01.2 USB Controller: NEC Corporation USB 2.0 (rev 02) 02:09.0 Modem: PCTel Inc HSP56 MicroModem (rev 04) 02:0a.0 Modem: PCTel Inc: Unknown device 2181 (rev 04) 02:0b.0 Modem: PCTel Inc HSP56 MicroModem (rev 04) 02:0c.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78) 02:0d.0 Modem: PCTel Inc HSP56 MicroModem (rev 04) But when I try to start the wcfxo module it doesn't work: [EMAIL PROTECTED] modprobe wcfxo Notice: Configuration file is /etc/zaptel.conf line 146: Unable to open master device '/dev/zap/ctl' And the linux kernel doesn't quite recognize them: Sep 6 18:58:45 asterisk2 kernel: zaptel: no version for struct_module found: kernel tainted. Sep 6 18:58:45 asterisk2 kernel: Zapata Telephony Interface Registered on major 196 When I try to configure the ztcfg it doesn't find anything on channel 1: [EMAIL PROTECTED] /sbin/ztcfg -vvv Zaptel Configuration == Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS Kewlstart (Default) (Slaves: 04) 4 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address (6) And Asterisk can't get them working: [chan_zap.so] = (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found Sep 6 19:01:34 WARNING[2549]: chan_zap.c:778 zt_open: Unable to specify channel 1: No such device or address Sep 6 19:01:34 ERROR[2549]: chan_zap.c:6239 mkintf: Unable to open channel 1: No such device or address here = 0, tmp-channel = 1, channel = 1 Sep 6 19:01:34 ERROR[2549]: chan_zap.c:9191 setup_zap: Unable to register channel '1-4' Sep 6 19:01:34 WARNING[2549]: loader.c:345 ast_load_resource: chan_zap.so: load_module failed, returning -1 == Unregistered channel type 'Tor' == Unregistered channel type 'Zap' Sep 6 19:01:34 WARNING[2549]: loader.c:440 load_modules: Loading module chan_zap.so failed! I've tried most of the pci cards and they all give the same result. When using a different type of card in that same PC i don't get those errors. I thought perhaps there is some software upgrade necessary for them to work, or something along those lines? Any help you could mention would be very appreciated. Thanks -- Ing CIP Alejandro Celi Mariátegui [EMAIL PROTECTED] El mar, 13-09-2005 a las 15:01, Mojo with Horan Company, LLC escribió: hisax seems to be a loadable module for an ISDN card. if: # lsmod | grep hisax prints any output, try # rmmod hisax; modprobe zaptel ? hth Mojo Shawn Porter wrote: I am getting quite frustrated today, so please bear with me. I just installed Fedora Core 4 (was running RedHat 9 with a working Asterisk) now my Fedora does not appear to be recognizing my X100P (clone) at all. Hardware browser just shows them as unknown device. driver: hisax So, of course, my zaptel drivers do not work and therefore my asterisk does not work. any help would be greatly appreciated….. Shawn ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] Fedora Core 4 not recognizing X100P cards
On Tue, 13 Sep 2005 15:21:02 -0400, Shawn Porter wrote I am getting quite frustrated today, so please bear with me. I just installed Fedora Core 4 (was running RedHat 9 with a working Asterisk) now my Fedora does not appear to be recognizing my X100P (clone) at all. Hardware browser just shows them as unknown device. driver: hisax So, of course, my zaptel drivers do not work and therefore my asterisk does not work. The trick to installing X100P clones on FC is that since Kudzu always configures them as an hisax device, you have to add a line removing the hisax module from memory before loading the zaptel modules. I inserted this into the start) section of /etc/init.d/zaptel modprobe -r hisax /dev/null Now the zaptel modules can load properly. -- Carlos Chavez Director de Tecnología Telecomunicaciones Abiertas de México S.A. de C.V. Tel: +52-55-91169161 Ext 2001 ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] Fedora Core 4 not recognizing X100P cards
My TDM400 on fc4 was working great.. all of sudden ..i am having the same issue ..you guys are having all i tried to run asterisk as non-root user.. and I was able to run it as non-root and was able to receive and send call using asterisk.. I am not sure.. what thing I did wrong and coz all the trouble.. Thanks -Original Message- From: [EMAIL PROTECTED] Sent: Tue, 13 Sep 2005 15:09:52 -0500 To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Fedora Core 4 not recognizing X100P cards I have the same problem. I've been having a bit of trouble getting the cards to work with asterisk, and I thought perhaps you might know what I might be doing wrong. I installed them in a linux box, and when I check to see if the OS has recognized them it looks fine: They show up as HSP56 MicroModem (rev 04) [EMAIL PROTECTED] lspci 00:00.0 Host bridge: Intel Corporation 82850 850 (Tehama) Chipset Host Bridge (MCH) (rev 04) 00:01.0 PCI bridge: Intel Corporation 82850 850 (Tehama) Chipset AGP Bridge (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 04) 00:1f.0 ISA bridge: Intel Corporation 82801BA ISA Bridge (LPC) (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801BA IDE U100 (rev 04) 00:1f.2 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #1) (rev 04) 00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus (rev 04) 00:1f.5 Multimedia audio controller: Intel Corporation 82801BA/BAM AC'97 Audio (rev 04) 01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 4000 AGP 8x] (rev c1) 02:01.0 USB Controller: NEC Corporation USB (rev 41) 02:01.1 USB Controller: NEC Corporation USB (rev 41) 02:01.2 USB Controller: NEC Corporation USB 2.0 (rev 02) 02:09.0 Modem: PCTel Inc HSP56 MicroModem (rev 04) 02:0a.0 Modem: PCTel Inc: Unknown device 2181 (rev 04) 02:0b.0 Modem: PCTel Inc HSP56 MicroModem (rev 04) 02:0c.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78) 02:0d.0 Modem: PCTel Inc HSP56 MicroModem (rev 04) But when I try to start the wcfxo module it doesn't work: [EMAIL PROTECTED] modprobe wcfxo Notice: Configuration file is /etc/zaptel.conf line 146: Unable to open master device '/dev/zap/ctl' And the linux kernel doesn't quite recognize them: Sep 6 18:58:45 asterisk2 kernel: zaptel: no version for struct_module found: kernel tainted. Sep 6 18:58:45 asterisk2 kernel: Zapata Telephony Interface Registered on major 196 When I try to configure the ztcfg it doesn't find anything on channel 1: [EMAIL PROTECTED] /sbin/ztcfg -vvv Zaptel Configuration == Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS Kewlstart (Default) (Slaves: 04) 4 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address (6) And Asterisk can't get them working: [chan_zap.so] = (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found Sep 6 19:01:34 WARNING[2549]: chan_zap.c:778 zt_open: Unable to specify channel 1: No such device or address Sep 6 19:01:34 ERROR[2549]: chan_zap.c:6239 mkintf: Unable to open channel 1: No such device or address here = 0, tmp-channel = 1, channel = 1 Sep 6 19:01:34 ERROR[2549]: chan_zap.c:9191 setup_zap: Unable to register channel '1-4' Sep 6 19:01:34 WARNING[2549]: loader.c:345 ast_load_resource: chan_zap.so: load_module failed, returning -1 == Unregistered channel type 'Tor' == Unregistered channel type 'Zap' Sep 6 19:01:34 WARNING[2549]: loader.c:440 load_modules: Loading module chan_zap.so failed! I've tried most of the pci cards and they all give the same result. When using a different type of card in that same PC i don't get those errors. I thought perhaps there is some software upgrade necessary for them to work, or something along those lines? Any help you could mention would be very appreciated. Thanks -- Ing CIP Alejandro Celi Mariátegui [EMAIL PROTECTED] El mar, 13-09-2005 a las 15:01, Mojo with Horan Company, LLC escribió: hisax seems to be a loadable module for an ISDN card. if: # lsmod | grep hisax prints any output, try # rmmod hisax; modprobe zaptel ? hth Mojo Shawn Porter wrote: I am getting quite frustrated today, so please bear with me. I just installed Fedora Core 4 (was running RedHat 9 with a working Asterisk) now my Fedora does not appear to be recognizing my X100P (clone) at all. Hardware browser just shows them as unknown device. driver: hisax So, of course, my zaptel drivers do not work and therefore my asterisk does not work. any help would be greatly appreciated….. Shawn
Re: [Asterisk-Users] Fedora Core 4 not recognizing X100P cards
We had our share of problems with the Fritz Card on FC4. Everything was OK except the speech was one-way in the outgoing direction. We spent days on it and couldn't find a solution to it. We discovered that the device nodes were not created correctly by udev. Enough was enough, we switched to SuSE 9.2 and within a day everything worked beautifully without much effort. I think FC4 has some serious problems with udev (some even claimed that it's not stable release) and I have never seen anyone successfully ran Asterisk on it. If you have a choice, switch to SuSE or other Linux distribution such as Debian. /Y.T. --- Innocent Evil [EMAIL PROTECTED] wrote: My TDM400 on fc4 was working great.. all of sudden ..i am having the same issue ..you guys are having all i tried to run asterisk as non-root user.. and I was able to run it as non-root and was able to receive and send call using asterisk.. I am not sure.. what thing I did wrong and coz all the trouble.. Thanks -Original Message- From: [EMAIL PROTECTED] Sent: Tue, 13 Sep 2005 15:09:52 -0500 To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Fedora Core 4 not recognizing X100P cards I have the same problem. I've been having a bit of trouble getting the cards to work with asterisk, and I thought perhaps you might know what I might be doing wrong. I installed them in a linux box, and when I check to see if the OS has recognized them it looks fine: They show up as HSP56 MicroModem (rev 04) [EMAIL PROTECTED] lspci 00:00.0 Host bridge: Intel Corporation 82850 850 (Tehama) Chipset Host Bridge (MCH) (rev 04) 00:01.0 PCI bridge: Intel Corporation 82850 850 (Tehama) Chipset AGP Bridge (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 04) 00:1f.0 ISA bridge: Intel Corporation 82801BA ISA Bridge (LPC) (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801BA IDE U100 (rev 04) 00:1f.2 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #1) (rev 04) 00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus (rev 04) 00:1f.5 Multimedia audio controller: Intel Corporation 82801BA/BAM AC'97 Audio (rev 04) 01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 4000 AGP 8x] (rev c1) 02:01.0 USB Controller: NEC Corporation USB (rev 41) 02:01.1 USB Controller: NEC Corporation USB (rev 41) 02:01.2 USB Controller: NEC Corporation USB 2.0 (rev 02) 02:09.0 Modem: PCTel Inc HSP56 MicroModem (rev 04) 02:0a.0 Modem: PCTel Inc: Unknown device 2181 (rev 04) 02:0b.0 Modem: PCTel Inc HSP56 MicroModem (rev 04) 02:0c.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78) 02:0d.0 Modem: PCTel Inc HSP56 MicroModem (rev 04) But when I try to start the wcfxo module it doesn't work: [EMAIL PROTECTED] modprobe wcfxo Notice: Configuration file is /etc/zaptel.conf line 146: Unable to open master device '/dev/zap/ctl' And the linux kernel doesn't quite recognize them: Sep 6 18:58:45 asterisk2 kernel: zaptel: no version for struct_module found: kernel tainted. Sep 6 18:58:45 asterisk2 kernel: Zapata Telephony Interface Registered on major 196 When I try to configure the ztcfg it doesn't find anything on channel 1: [EMAIL PROTECTED] /sbin/ztcfg -vvv Zaptel Configuration == Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS Kewlstart (Default) (Slaves: 04) 4 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address (6) And Asterisk can't get them working: [chan_zap.so] = (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found Sep 6 19:01:34 WARNING[2549]: chan_zap.c:778 zt_open: Unable to specify channel 1: No such device or address Sep 6 19:01:34 ERROR[2549]: chan_zap.c:6239 mkintf: Unable to open channel 1: No such device or address here = 0, tmp-channel = 1, channel = 1 Sep 6 19:01:34 ERROR[2549]: chan_zap.c:9191 setup_zap: Unable to register channel '1-4' Sep 6 19:01:34 WARNING[2549]: loader.c:345 ast_load_resource: chan_zap.so: load_module failed, returning -1 == Unregistered channel type 'Tor' == Unregistered channel type 'Zap' Sep 6 19:01:34 WARNING[2549]: loader.c:440 load_modules: Loading module chan_zap.so failed! I've tried most of the pci cards and they all give the same result. When using a different type of card in that same PC i don't get those errors. I thought perhaps there is some software upgrade necessary for them to work, or something along those lines? Any help you could mention would be very appreciated. Thanks -- Ing CIP Alejandro Celi Mariátegui [EMAIL PROTECTED] El mar, 13-09-2005 a las 15:01, Mojo with Horan Company, LLC
Re: [Asterisk-Users] Fedora Core 4 not recognizing X100P cards
Shawn Porter, just a few hours ago, after rmmod-ing hisax and modprobe-ing zaptel, seems to have success on FC4. Still working good, Shawn? I have heard of some other successful reports too on FC4, but I have heard rumors of instability/inadequacy for reasons other than udev I think. YT Lim wrote: We had our share of problems with the Fritz Card on FC4. Everything was OK except the speech was one-way in the outgoing direction. We spent days on it and couldn't find a solution to it. We discovered that the device nodes were not created correctly by udev. Enough was enough, we switched to SuSE 9.2 and within a day everything worked beautifully without much effort. I think FC4 has some serious problems with udev (some even claimed that it's not stable release) and I have never seen anyone successfully ran Asterisk on it. If you have a choice, switch to SuSE or other Linux distribution such as Debian. /Y.T. --- Innocent Evil [EMAIL PROTECTED] wrote: My TDM400 on fc4 was working great.. all of sudden ..i am having the same issue ..you guys are having all i tried to run asterisk as non-root user.. and I was able to run it as non-root and was able to receive and send call using asterisk.. I am not sure.. what thing I did wrong and coz all the trouble.. Thanks -Original Message- From: [EMAIL PROTECTED] Sent: Tue, 13 Sep 2005 15:09:52 -0500 To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Fedora Core 4 not recognizing X100P cards I have the same problem. I've been having a bit of trouble getting the cards to work with asterisk, and I thought perhaps you might know what I might be doing wrong. I installed them in a linux box, and when I check to see if the OS has recognized them it looks fine: They show up as HSP56 MicroModem (rev 04) [EMAIL PROTECTED] lspci 00:00.0 Host bridge: Intel Corporation 82850 850 (Tehama) Chipset Host Bridge (MCH) (rev 04) 00:01.0 PCI bridge: Intel Corporation 82850 850 (Tehama) Chipset AGP Bridge (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 04) 00:1f.0 ISA bridge: Intel Corporation 82801BA ISA Bridge (LPC) (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801BA IDE U100 (rev 04) 00:1f.2 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #1) (rev 04) 00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus (rev 04) 00:1f.5 Multimedia audio controller: Intel Corporation 82801BA/BAM AC'97 Audio (rev 04) 01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 4000 AGP 8x] (rev c1) 02:01.0 USB Controller: NEC Corporation USB (rev 41) 02:01.1 USB Controller: NEC Corporation USB (rev 41) 02:01.2 USB Controller: NEC Corporation USB 2.0 (rev 02) 02:09.0 Modem: PCTel Inc HSP56 MicroModem (rev 04) 02:0a.0 Modem: PCTel Inc: Unknown device 2181 (rev 04) 02:0b.0 Modem: PCTel Inc HSP56 MicroModem (rev 04) 02:0c.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78) 02:0d.0 Modem: PCTel Inc HSP56 MicroModem (rev 04) But when I try to start the wcfxo module it doesn't work: [EMAIL PROTECTED] modprobe wcfxo Notice: Configuration file is /etc/zaptel.conf line 146: Unable to open master device '/dev/zap/ctl' And the linux kernel doesn't quite recognize them: Sep 6 18:58:45 asterisk2 kernel: zaptel: no version for struct_module found: kernel tainted. Sep 6 18:58:45 asterisk2 kernel: Zapata Telephony Interface Registered on major 196 When I try to configure the ztcfg it doesn't find anything on channel 1: [EMAIL PROTECTED] /sbin/ztcfg -vvv Zaptel Configuration == Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS Kewlstart (Default) (Slaves: 04) 4 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address (6) And Asterisk can't get them working: [chan_zap.so] = (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found Sep 6 19:01:34 WARNING[2549]: chan_zap.c:778 zt_open: Unable to specify channel 1: No such device or address Sep 6 19:01:34 ERROR[2549]: chan_zap.c:6239 mkintf: Unable to open channel 1: No such device or address here = 0, tmp-channel = 1, channel = 1 Sep 6 19:01:34 ERROR[2549]: chan_zap.c:9191 setup_zap: Unable to register channel '1-4' Sep 6 19:01:34 WARNING[2549]: loader.c:345 ast_load_resource: chan_zap.so: load_module failed, returning -1 == Unregistered channel type 'Tor' == Unregistered channel type 'Zap' Sep 6 19:01:34 WARNING[2549]: loader.c:440 load_modules: Loading module chan_zap.so failed! I've tried most of the pci cards and they all give the same result. When using a different type of card in that same PC i don't get those errors. I thought perhaps there is some software upgrade necessary for them to work, or something along those lines? Any
Re: [Asterisk-Users] Fedora Core 4 not recognizing X100P cards
Well, as I told earlier.. my asterisk was running great with one fxo and one fxs module of a TDM400P All i tried last night to run asterisk with non-root I must did something wrong while I was trying to do that FXO module on channel # 1 FXS module on channel # 4 /etc/zaptel.conf - loadzone = us defaultzone=us fxoks=1 fxsks=4 /etc/asterisk/zapata.conf signalling=fxo_ks channel=1 signalling=fxs_ks channel=4 Did I made any mistake above? /etc/modprobe.conf - install wcfxo /sbin/modprobe --ignore-install wcfxo /sbin/ztcfg install wctdm /sbin/modprobe --ignore-install wctdm /sbin/ztcfg # there have more line in it.. i guess they are not important here alias wcfxs wctdm /etc/rc.d/init.d/asterisk - #important lines are below start) /sbin/modprobe wctdm daemon /usr/sbin/asterisk stop) killproc asterisk /sbin/modprobe -r wctdm Here is the output of asterisk -vvvc Sep 13 22:18:11 WARNING[3982]: chan_zap.c:887 zt_open: Unable to specify channel 1: No such device Sep 13 22:18:11 ERROR[3982]: chan_zap.c:6612 mkintf: Unable to open channel 1: No such device here = 0, tmp-channel = 1, channel = 1 Sep 13 22:18:11 ERROR[3982]: chan_zap.c:9990 setup_zap: Unable to register channel '1' Sep 13 22:18:11 WARNING[3982]: loader.c:403 __load_resource: chan_zap.so: load_module failed, returning -1 Sep 13 22:18:11 WARNING[3982]: loader.c:543 load_modules: Loading module chan_zap.so failed! see I have channel # 1 [EMAIL PROTECTED] ~]# ls -l /dev/zap/ total 0 crw-rw 1 root asterisk 196, 1 Sep 13 22:20 1 crw-rw 1 root asterisk 196, 2 Sep 13 22:20 2 crw-rw 1 root asterisk 196, 3 Sep 13 22:20 3 crw-rw 1 root asterisk 196, 4 Sep 13 22:20 4 crw-rw 1 root asterisk 196, 254 Sep 13 22:20 channel crw-rw 1 root asterisk 196, 0 Sep 13 22:20 ctl crw-rw 1 root asterisk 196, 255 Sep 13 22:20 pseudo crw-rw 1 root asterisk 196, 253 Sep 13 22:20 timer After all of this, if I comment out this from /etc/asterisk/zapata.conf /etc/asterisk/zapata.conf ;signalling=fxo_ks ;channel=1 signalling=fxs_ks channel=4 My asterisk run fine .. I just dont able to use my phone set attaced to my fxs module. And all I had to do is .. forward all incoming call to my voicemail box !! Should I consider my fxs card has burnt out !! Thanks for reading.. hope someone will reply me to help. Thanks again, -Original Message- From: [EMAIL PROTECTED] Sent: Wed, 14 Sep 2005 09:37:00 +1000 (EST) To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Fedora Core 4 not recognizing X100P cards We had our share of problems with the Fritz Card on FC4. Everything was OK except the speech was one-way in the outgoing direction. We spent days on it and couldn't find a solution to it. We discovered that the device nodes were not created correctly by udev. Enough was enough, we switched to SuSE 9.2 and within a day everything worked beautifully without much effort. I think FC4 has some serious problems with udev (some even claimed that it's not stable release) and I have never seen anyone successfully ran Asterisk on it. If you have a choice, switch to SuSE or other Linux distribution such as Debian. /Y.T. --- Innocent Evil [EMAIL PROTECTED] wrote: My TDM400 on fc4 was working great.. all of sudden ..i am having the same issue ..you guys are having all i tried to run asterisk as non-root user.. and I was able to run it as non-root and was able to receive and send call using asterisk.. I am not sure.. what thing I did wrong and coz all the trouble.. Thanks -Original Message- From: [EMAIL PROTECTED] Sent: Tue, 13 Sep 2005 15:09:52 -0500 To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Fedora Core 4 not recognizing X100P cards I have the same problem. I've been having a bit of trouble getting the cards to work with asterisk, and I thought perhaps you might know what I might be doing wrong. I installed them in a linux box, and when I check to see if the OS has recognized them it looks fine: They show up as HSP56 MicroModem (rev 04) [EMAIL PROTECTED] lspci 00:00.0 Host bridge: Intel Corporation 82850 850 (Tehama) Chipset Host Bridge (MCH) (rev 04) 00:01.0 PCI bridge: Intel Corporation 82850 850 (Tehama) Chipset AGP Bridge (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 04) 00:1f.0 ISA bridge: Intel Corporation 82801BA ISA Bridge (LPC) (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801BA IDE U100 (rev 04) 00:1f.2 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #1) (rev 04) 00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus (rev 04) 00:1f.5 Multimedia audio controller: Intel Corporation 82801BA/BAM AC'97 Audio
