Re: [Chevelle-list] Thermostat ?'s
Krister- The hotter you run your engine, the more efficient it gets, which is why new cars tend to run between 200 and 230 degrees. Same reason Nascar runs theirs so hot. On the other hand a cooler engine with a cooler intake charge will tend to make more power. I was taught to drill a hole in the flange of the tstat years ago by a guy who had been wrenching since dirt was new. It does 2 things: When you do the initial fill of an engine with coolant, it allows the air to escape while the coolant comes up under the thermostat. Without coolant on the thermostat to make it hot, it may not open at all and seriously overheat your engine. The other reason is that each time you start your engine up cold, the water pump is pushing coolant out the bottom of the pump, up through the radiator through the upper hose and against the tstat. Having that small hole there allows the pressure to release somewhat, making it less likely to blow a hose somewhere. Devin _ From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of [EMAIL PROTECTED] Sent: Thursday, April 26, 2007 1:43 PM To: Chevelle List Subject: [Chevelle-list] Thermostat ?'s I am replacing a leaking thermostat gasket and will replace thermostat while apart. Currently it has a 195* and works fine holding temp a 195*. Autoparts store suggested to put a 180* to run it a little cooler. Good, Bad or Indifferent? Secondly: I have read in the past about drilling an 1/8” hole in the thermostat flange to relieve an air bubble if it forms at the thermostat. Anyone do this? Autoparts store said many already come with a hole. The Stant I bought did not. Thank you, Krister Meister '66 SS #'s No virus found in this incoming message. Checked by AVG Free Edition. Version: 7.5.463 / Virus Database: 269.6.1/776 - Release Date: 4/25/2007 12:19 PM No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.5.467 / Virus Database: 269.6.1/778 - Release Date: 4/27/2007 1:39 PM
Re: [Chevelle-list] Thermostat ?'s
In a message dated 4/26/2007 4:32:42 PM Central Daylight Time, [EMAIL PROTECTED] writes: I’ve heard of drilling a hole in the stat, 1/16 yes i have done this!! sure can't hurt!! Harlan ** See what's free at http://www.aol.com.
[Chevelle-list] Thermostat ?'s
I am replacing a leaking thermostat gasket and will replace thermostat while apart. Currently it has a 195* and works fine holding temp a 195*. Autoparts store suggested to put a 180* to run it a little cooler. Good, Bad or Indifferent? Secondly: I have read in the past about drilling an 1/8 hole in the thermostat flange to relieve an air bubble if it forms at the thermostat. Anyone do this? Autoparts store said many already come with a hole. The Stant I bought did not. Thank you, Krister Meister '66 SS #'s
Re: [Chevelle-list] Thermostat ?'s
All 66 V8s w/o A.I.R. came with 180 degree stats, those with A.I.R. came with 195 degree stats. Cylinder wear can occur with too cool an engine as well as too hot an engine. Published optimum performance figures I've seen for water temp is between 170 and 185 or so and optimum overall operating water temp is about 180 to 200. If it runs fine now and doesn't overheat with the 195, I'd use the same. With summer coming on, the 180 may give you a little more buffer zone against overheating when caught in traffic if that's a concern. I've heard of drilling a hole in the stat, either 1/16 or 1/8, especially on a big block when the bypass hose is removed. Many new cars come with a bleed hole (or holes) in the stat to avoid trapping air. Drilling a hole is free and couldn't hurt if your replacement doesn't have one. You can do some research on the web and, for the price of a gasket, remove the stat and drill a hole in it. People will say they've run stats for years with no stinking hole in them and never had a problem. People used to drive on 2-ply/4-ply rating bias tires too but technology moves on. :*) Dale McIntosh http://www.chevellecd.com 1966/67 Chevelle Reference CDs ChevelleStuff.com http://www.chevellestuff.com ACES #1709/TC GOLD #92 http://www.chevellecd.com _ From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of [EMAIL PROTECTED] Sent: Thursday, April 26, 2007 3:43 PM To: Chevelle List Subject: [Chevelle-list] Thermostat ?'s I am replacing a leaking thermostat gasket and will replace thermostat while apart. Currently it has a 195* and works fine holding temp a 195*. Autoparts store suggested to put a 180* to run it a little cooler. Good, Bad or Indifferent? Secondly: I have read in the past about drilling an 1/8 hole in the thermostat flange to relieve an air bubble if it forms at the thermostat. Anyone do this? Autoparts store said many already come with a hole. The Stant I bought did not. Thank you, Krister Meister '66 SS #'s _ avast! Antivirus http://www.avast.com : Outbound message clean. Virus Database (VPS): 000736-2, 04/26/2007 Tested on: 4/26/2007 4:25:40 PM avast! - copyright (c) 1988-2007 ALWIL Software.
Re: [Chevelle-list] Thermostat ?'s
HELLO, my 427 likes it around 165-180. As for drilling a pin hole (unsure) I have never had any problems with air pockets 67ss. Perry /HTML
[Chevelle-list] Thermostat
Looking to change / replace the thermostat in my ' 69 Chevelle . Not sure what temp. thermostat is in there now . What would be a good temp thermostat to install , 160 ? Engine is 396/402 .Looking to do some work on the cooling system , ie replace radiator , hoses ,etc and thought it would be a good time to change the thermostat . Pete Hnat ' 69 Chevelle SS
Re: [Chevelle-list] Thermostat
I use a 160 in my 396. Have for 15 years.
Re: [Chevelle-list] Thermostat
Pete, Your engine most likely came with a 180 thermostat. 160 would be fine as well. Neither will effect the ultimate temp, just how quick it get's there. mike - Original Message - From: Peter Hnat [EMAIL PROTECTED] To: chevelle-list@chevelles.net Sent: Wednesday, July 06, 2005 9:24 AM Subject: [Chevelle-list] Thermostat Looking to change / replace the thermostat in my ' 69 Chevelle . Not sure what temp. thermostat is in there now . What would be a good temp thermostat to install , 160 ? Engine is 396/402 .Looking to do some work on the cooling system , ie replace radiator , hoses ,etc and thought it would be a good time to change the thermostat . Pete Hnat ' 69 Chevelle SS
RE: [Chevelle-list] Thermostat
I think youll find three basic choices 160, 180, and 195. Personally, Ive always used 180s, and like the previous poster, have done so for 15 years. I think 160 is a little cool for full temp, but thats me. Youd do fine with either. 195 is a common OEM thermostat temp, I believe. -Dave From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of [EMAIL PROTECTED] Sent: Wednesday, July 06, 2005 10:28 AM To: Chevelle-list@chevelles.net Subject: Re: [Chevelle-list] Thermostat I use a 160 in my 396. Have for 15 years.
Re: [Chevelle-list] Thermostat
Yeah,I run a 180 thermostat year round in my car. Works well in summer and winter. Clint HooperHH Custom,owner1969 El Camino ProTourer2001 H-D FLHR custom baggerhttp://dalesplace.com/misc/friends/clint/clint_hooper.htm - Original Message - From: Dave Studly I think youll find three basic choices 160, 180, and 195. Personally, Ive always used 180s, and like the previous poster, have done so for 15 years. I think 160 is a little cool for full temp, but thats me. Youd do fine with either. 195 is a common OEM thermostat temp, I believe. -Dave From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of [EMAIL PROTECTED]Sent: Wednesday, July 06, 2005 10:28 AMTo: Chevelle-list@chevelles.netSubject: Re: [Chevelle-list] Thermostat I use a 160 in my 396. Have for 15 years.
Re: [Chevelle-list] Thermostat
From: Mike Holleman [EMAIL PROTECTED] Subject: Re: [Chevelle-list] Thermostat Pete, Your engine most likely came with a 180 thermostat. 160 would be fine as well. Neither will effect the ultimate temp, just how quick it get's there. mike That may be true in summer, but in cold weather the cooling system will run close to the thermostat setting. It will also effect heater output. Pete driven to work w/ cardboard blocking radiator Geurds
Re: [Chevelle-list] thermostat question
WOW- Never expected to get such a wide response rate with my dinky little thermostat question! Anyhow, here's the details on my '66: 1. shroud installed (don't know if there was one there when it came from the factory or not) 2. stock 4-blade fan 3. stock water pump pulley (the pump is from Auto Zone, but it's for a stock 327) 4. thermostat came from Auto Zone too (at that point I didn't know there were so many choices for thermostats) 5. radiator is a new replacement radiator that is for a '66 Chevelle with a 327 (don't remember how many rows, but I can check when I get home tonite) I ordered the 180 degree thermostat from Jegs, and will keep you all posted on whether or not it helps- They banged me over the head with a $10 shipping charge though, so it must be made out of solid gold 8^] Thanks for all the input! Jim '66 Malibu '59 Corvette 1959 Corvette Registry, Webmaster http://59vette.cjb.net --- Dave Benjamin [EMAIL PROTECTED] wrote: When doing a show car and wanting to keep the original look etc. You don't add a 7 blade fan, you don't butcher a fan shroud into THE CAR EITHER. I changed the thermostat to keep it running COOL. YES THAT IS MY POINT AND I HOPE IT HELPS YOUR DISCUSSION JOHN Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/ - Original Message - From: John Nasta [EMAIL PROTECTED] To: The Chevelle Mailing List [EMAIL PROTECTED] Sent: Thursday, April 01, 2004 1:51 PM Subject: RE: [Chevelle-list] thermostat question I believe you. Is that connected in any way to this discussion of how to achieve better cooling in a car that runs hot? -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Dave Benjamin Sent: Thursday, April 01, 2004 1:05 PM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question My 66 was factory 4 blade fan, rad size with 2 spd and no shroud. Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/ - Original Message - From: John Nasta [EMAIL PROTECTED] To: The Chevelle Mailing List [EMAIL PROTECTED] Sent: Thursday, April 01, 2004 12:53 PM Subject: RE: [Chevelle-list] thermostat question As Brad pointed out, the thermostat has more to do with engine warming than cooling. A fan shroud, a higher volume fan, a smaller WP pulley, or a bigger (or less restricted) radiator would help. John Nasta -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Dave Benjamin Sent: Thursday, April 01, 2004 12:29 PM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question I tried a 160 in my 1966 chevelle and it didn't work very well. There was no fan shroud factory and ounce the motor got up to 160 it wouldn't (open/ close) cycle. It would stay open therefore not very good cooling. The 180 worked fine it it. Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/ __ Do you Yahoo!? Yahoo! Small Business $15K Web Design Giveaway http://promotions.yahoo.com/design_giveaway/
RE: [Chevelle-list] thermostat question
I ordered the 180 degree thermostat from Jegs, and will keep you all posted on whether or not it helps- They banged me over the head with a $10 shipping charge though, so it must be made out of solid gold 8^] Ouch, you did get banged on that. Your local Autozone should have one of those in stock for less than $5. Certainly less than $10. -Dave
Re: [Chevelle-list] thermostat question
Gotta ask that dreaded shipping price first!!Especially on e-bay if not stated!! I fell into that paid more for shipping than item cost once - Original Message - From: Dave Studly [EMAIL PROTECTED] To: The Chevelle Mailing List [EMAIL PROTECTED] Sent: Friday, April 02, 2004 11:05 AM Subject: RE: [Chevelle-list] thermostat question I ordered the 180 degree thermostat from Jegs, and will keep you all posted on whether or not it helps- They banged me over the head with a $10 shipping charge though, so it must be made out of solid gold 8^] Ouch, you did get banged on that. Your local Autozone should have one of those in stock for less than $5. Certainly less than $10. -Dave
RE: [Chevelle-list] thermostat question
One good thing about ordering via the web is that you get to see the shipping cost before concluding the ordering process. However, there are some things you should never order through the mail, mainly because your local auto parts store has them and it is much faster and cheaper to buy them locally.
RE: [Chevelle-list] thermostat question
Well Jeg's shipping is actually free, they just nab you a flat rate for handling...Big orders are the way to go with them.. Ron http://home.comcast.net/~cutter169/index.htm -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of John Nasta Sent: Friday, April 02, 2004 12:24 PM To: The Chevelle Mailing List Subject: RE: [Chevelle-list] thermostat question One good thing about ordering via the web is that you get to see the shipping cost before concluding the ordering process. However, there are some things you should never order through the mail, mainly because your local auto parts store has them and it is much faster and cheaper to buy them locally.
[Chevelle-list] thermostat question
Hi Gang, I just ordered a Be Cool 180 degree thermostat for my '66 327 from Jeg's, and had a question about it- They also offered a 160 degree model. I spoke w/another car enthusiast, and they advised to stick with the 180 thermostat, as the 160 might impact how well the heater performs in the Winter. Can anyone provide any feedback on the 2 options, and will this definitely help my motor run cooler? She currently runs a constant 210. I wanted to see what options I had without having to install an electric fan just yet.. Thanks! Jim '66 Malibu '59 Corvette 1959 Corvette Registry, Webmaster http://59vette.cjb.net __ Do you Yahoo!? Yahoo! Small Business $15K Web Design Giveaway http://promotions.yahoo.com/design_giveaway/
Re: [Chevelle-list] thermostat question
Unless you live in a hot climate (which you don't) a 180 thermostat is fine for the street. However, if your cooling system currently is at 210 the thermostat alone won't fix it; it'll open earlier (do you have a 195 in there now?) and slow the temperature ascent but eventually it'll still reach 210. Have you verified that this 210 reading is accurate? Factory gauge or aftermarket? How old is the sending unit? GM gauges work based on resistance and if you can locate the resistance scale for your car (a factory service manual might contain it) you can use a combination of resistors to check the accuracy of the gauge. A fan shroud always helps with a mechanical fan but I don't know if '66s came with one from the factory or what your feeling is regarding the addition of one. I personally like fixed-blade fans used in conjuction with thermal clutches. The radiator isn't very old, is it? How long has it been since the system's been flushed? Brad O. I just ordered a Be Cool 180 degree thermostat for my '66 327 from Jeg's, and had a question about it- They also offered a 160 degree model. I spoke w/another car enthusiast, and they advised to stick with the 180 thermostat, as the 160 might impact how well the heater performs in the Winter. Can anyone provide any feedback on the 2 options, and will this definitely help my motor run cooler? She currently runs a constant 210. I wanted to see what options I had without having to install an electric fan just yet.. Thanks! Jim
RE: [Chevelle-list] thermostat question
Try a smaller WP pulley. Just think of a 10-speed bike. It will make your fan turn at a higher RPM. John Nasta Old Car Network http://oldcarnetwork.com -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of [EMAIL PROTECTED] Sent: Thursday, April 01, 2004 11:48 AM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question Unless you live in a hot climate (which you don't) a 180 thermostat is fine for the street. However, if your cooling system currently is at 210 the thermostat alone won't fix it; it'll open earlier (do you have a 195 in there now?) and slow the temperature ascent but eventually it'll still reach 210. Have you verified that this 210 reading is accurate? Factory gauge or aftermarket? How old is the sending unit? GM gauges work based on resistance and if you can locate the resistance scale for your car (a factory service manual might contain it) you can use a combination of resistors to check the accuracy of the gauge. A fan shroud always helps with a mechanical fan but I don't know if '66s came with one from the factory or what your feeling is regarding the addition of one. I personally like fixed-blade fans used in conjuction with thermal clutches. The radiator isn't very old, is it? How long has it been since the system's been flushed? Brad O. I just ordered a Be Cool 180 degree thermostat for my '66 327 from Jeg's, and had a question about it- They also offered a 160 degree model. I spoke w/another car enthusiast, and they advised to stick with the 180 thermostat, as the 160 might impact how well the heater performs in the Winter. Can anyone provide any feedback on the 2 options, and will this definitely help my motor run cooler? She currently runs a constant 210. I wanted to see what options I had without having to install an electric fan just yet.. Thanks! Jim
Re: [Chevelle-list] thermostat question
I tried a 160 in my 1966 chevelle and it didn't work very well. There was no fan shroud factory and ounce the motor got up to 160 it wouldn't (open/ close) cycle. It would stay open therefore not very good cooling. The 180 worked fine it it. Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/ - Original Message - From: John Nasta [EMAIL PROTECTED] To: The Chevelle Mailing List [EMAIL PROTECTED] Sent: Thursday, April 01, 2004 12:19 PM Subject: RE: [Chevelle-list] thermostat question Try a smaller WP pulley. Just think of a 10-speed bike. It will make your fan turn at a higher RPM. John Nasta Old Car Network http://oldcarnetwork.com -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of [EMAIL PROTECTED] Sent: Thursday, April 01, 2004 11:48 AM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question Unless you live in a hot climate (which you don't) a 180 thermostat is fine for the street. However, if your cooling system currently is at 210 the thermostat alone won't fix it; it'll open earlier (do you have a 195 in there now?) and slow the temperature ascent but eventually it'll still reach 210. Have you verified that this 210 reading is accurate? Factory gauge or aftermarket? How old is the sending unit? GM gauges work based on resistance and if you can locate the resistance scale for your car (a factory service manual might contain it) you can use a combination of resistors to check the accuracy of the gauge. A fan shroud always helps with a mechanical fan but I don't know if '66s came with one from the factory or what your feeling is regarding the addition of one. I personally like fixed-blade fans used in conjuction with thermal clutches. The radiator isn't very old, is it? How long has it been since the system's been flushed? Brad O. I just ordered a Be Cool 180 degree thermostat for my '66 327 from Jeg's, and had a question about it- They also offered a 160 degree model. I spoke w/another car enthusiast, and they advised to stick with the 180 thermostat, as the 160 might impact how well the heater performs in the Winter. Can anyone provide any feedback on the 2 options, and will this definitely help my motor run cooler? She currently runs a constant 210. I wanted to see what options I had without having to install an electric fan just yet.. Thanks! Jim
RE: [Chevelle-list] thermostat question
As Brad pointed out, the thermostat has more to do with engine warming than cooling. A fan shroud, a higher volume fan, a smaller WP pulley, or a bigger (or less restricted) radiator would help. John Nasta -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Dave Benjamin Sent: Thursday, April 01, 2004 12:29 PM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question I tried a 160 in my 1966 chevelle and it didn't work very well. There was no fan shroud factory and ounce the motor got up to 160 it wouldn't (open/ close) cycle. It would stay open therefore not very good cooling. The 180 worked fine it it. Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/
Re: [Chevelle-list] thermostat question
My 66 was factory 4 blade fan, rad size with 2 spd and no shroud. Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/ - Original Message - From: John Nasta [EMAIL PROTECTED] To: The Chevelle Mailing List [EMAIL PROTECTED] Sent: Thursday, April 01, 2004 12:53 PM Subject: RE: [Chevelle-list] thermostat question As Brad pointed out, the thermostat has more to do with engine warming than cooling. A fan shroud, a higher volume fan, a smaller WP pulley, or a bigger (or less restricted) radiator would help. John Nasta -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Dave Benjamin Sent: Thursday, April 01, 2004 12:29 PM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question I tried a 160 in my 1966 chevelle and it didn't work very well. There was no fan shroud factory and ounce the motor got up to 160 it wouldn't (open/ close) cycle. It would stay open therefore not very good cooling. The 180 worked fine it it. Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/
Re: [Chevelle-list] thermostat question
Which also runs the pump faster and may not allow the water to go through the radiator slow enough for thermal efficiency. Have you heard of people putting restrictors on the return side of the radiator to do just that? But unless the radiator is new or obviously in perfect condition, I've always found that the best place to start with a heating problem. My .02. ER John Nasta wrote: Try a smaller WP pulley. Just think of a 10-speed bike. It will make your fan turn at a higher RPM. John Nasta Old Car Network http://oldcarnetwork.com -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of [EMAIL PROTECTED] Sent: Thursday, April 01, 2004 11:48 AM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question Unless you live in a hot climate (which you don't) a 180 thermostat is fine for the street. However, if your cooling system currently is at 210 the thermostat alone won't fix it; it'll open earlier (do you have a 195 in there now?) and slow the temperature ascent but eventually it'll still reach 210. Have you verified that this 210 reading is accurate? Factory gauge or aftermarket? How old is the sending unit? GM gauges work based on resistance and if you can locate the resistance scale for your car (a factory service manual might contain it) you can use a combination of resistors to check the accuracy of the gauge. A fan shroud always helps with a mechanical fan but I don't know if '66s came with one from the factory or what your feeling is regarding the addition of one. I personally like fixed-blade fans used in conjuction with thermal clutches. The radiator isn't very old, is it? How long has it been since the system's been flushed? Brad O. I just ordered a Be Cool 180 degree thermostat for my '66 327 from Jeg's, and had a question about it- They also offered a 160 degree model. I spoke w/another car enthusiast, and they advised to stick with the 180 thermostat, as the 160 might impact how well the heater performs in the Winter. Can anyone provide any feedback on the 2 options, and will this definitely help my motor run cooler? She currently runs a constant 210. I wanted to see what options I had without having to install an electric fan just yet.. Thanks! Jim
RE: [Chevelle-list] thermostat question
I believe you. Is that connected in any way to this discussion of how to achieve better cooling in a car that runs hot? -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Dave Benjamin Sent: Thursday, April 01, 2004 1:05 PM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question My 66 was factory 4 blade fan, rad size with 2 spd and no shroud. Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/ - Original Message - From: John Nasta [EMAIL PROTECTED] To: The Chevelle Mailing List [EMAIL PROTECTED] Sent: Thursday, April 01, 2004 12:53 PM Subject: RE: [Chevelle-list] thermostat question As Brad pointed out, the thermostat has more to do with engine warming than cooling. A fan shroud, a higher volume fan, a smaller WP pulley, or a bigger (or less restricted) radiator would help. John Nasta -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Dave Benjamin Sent: Thursday, April 01, 2004 12:29 PM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question I tried a 160 in my 1966 chevelle and it didn't work very well. There was no fan shroud factory and ounce the motor got up to 160 it wouldn't (open/ close) cycle. It would stay open therefore not very good cooling. The 180 worked fine it it. Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/
Re: [Chevelle-list] thermostat question
If it runs at a constant 210 a thermostat will do nothing for you if your current one is operation correctlly. Radiator and water pump(pulley) would be where to look for cooler constant temp. I agree that most times the radiator is at fault... whether is is too small, old, partially blocked... etc. Mikey _ Find a broadband plan that fits. Great local deals on high-speed Internet access. https://broadband.msn.com/?pgmarket=en-us/go/onm00200360ave/direct/01/
RE: [Chevelle-list] thermostat question
That's a good point. Assuming the radiator is good, I would try a 7-blade fan. A restrictor also means that the coolant is staying in the block longer. It may be self-defeating. Doesn't sound like a good idea to me. As Brad said, a shroud also helps quite a bit. You can also have an air dam down below to help force the fan to pull air through the radiator rather than from under the bumper. John Nasta -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Ed Riggins Sent: Thursday, April 01, 2004 1:29 PM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question Which also runs the pump faster and may not allow the water to go through the radiator slow enough for thermal efficiency. Have you heard of people putting restrictors on the return side of the radiator to do just that? But unless the radiator is new or obviously in perfect condition, I've always found that the best place to start with a heating problem. My .02. ER John Nasta wrote: Try a smaller WP pulley. Just think of a 10-speed bike. It will make your fan turn at a higher RPM. John Nasta Old Car Network http://oldcarnetwork.com
Re: [Chevelle-list] thermostat question
I read a bunch of he replies,, some vary good points. Still not sure if your 210 Deg is with a thermostat installed ? A 195 deg will keep the coolant in the radiator the longest = the lowest possible coolant temp re entering the block... If you Rad at present dose not have the ability to dissipate the heat.. a number of the options can help.. !. fan shroud 2. larger air flow fan 3. HI flow water pump ( higher exchange rate = more time for coolant in the rad ) 4. smaller dia pulley see above,plus higher fan speed at low RPM's Wayne ACES # 1556 TC # 186 From: J. Brady [EMAIL PROTECTED] To: [EMAIL PROTECTED] Sent: Thursday, April 01, 2004 11:23 AM Subject: [Chevelle-list] thermostat question Hi Gang, I just ordered a Be Cool 180 degree thermostat for my '66 327 from Jeg's, and had a question about it- They also offered a 160 degree model. I spoke w/another car enthusiast, and they advised to stick with the 180 thermostat, as the 160 might impact how well the heater performs in the Winter. Can anyone provide any feedback on the 2 options, and will this definitely help my motor run cooler? She currently runs a constant 210. I wanted to see what options I had without having to install an electric fan just yet.. Thanks! Jim '66 Malibu '59 Corvette 1959 Corvette Registry, Webmaster http://59vette.cjb.net __ Do you Yahoo!? Yahoo! Small Business $15K Web Design Giveaway http://promotions.yahoo.com/design_giveaway/
RE: [Chevelle-list] thermostat question
Reading what Stewart (a popular name in aftermarket water pumps) says about thermostats: A common misconception is that if coolant flows too quickly through the system, that it will not have time to cool properly. However the cooling system is a closed loop, so if you are keeping the coolant in the radiator longer to allow it to cool, you are also allowing it to stay in the engine longer, which increases coolant temperatures. Coolant in the engine will actually boil away from critical heat areas within the cooling system if not forced through the cooling system at a sufficiently high velocity. This situation is a common cause of so-called hot spots, which can lead to failures. Years ago, cars used low pressure radiator caps with upright-style radiators. At high RPM, the water pump pressure would overcome the radiator cap's rating and force coolant out, resulting in an overheated engine. Many enthusiasts mistakenly believed that these situations were caused because the coolant was flowing through the radiator so quickly, that it did not have time to cool. Using restrictors or slowing water pump speed prevented the coolant from being forced out, and allowed the engine to run cooler. However, cars built in the past thirty years have used cross flow radiators that position the radiator cap on the low pressure (suction) side of the system. This type of system does not subject the radiator cap to pressure from the water pump, so it benefits from maximizing coolant flow, not restricting it. Dale McIntosh
Re: [Chevelle-list] thermostat question
When doing a show car and wanting to keep the original look etc. You don't add a 7 blade fan, you don't butcher a fan shroud into THE CAR EITHER. I changed the thermostat to keep it running COOL. YES THAT IS MY POINT AND I HOPE IT HELPS YOUR DISCUSSION JOHN Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/ - Original Message - From: John Nasta [EMAIL PROTECTED] To: The Chevelle Mailing List [EMAIL PROTECTED] Sent: Thursday, April 01, 2004 1:51 PM Subject: RE: [Chevelle-list] thermostat question I believe you. Is that connected in any way to this discussion of how to achieve better cooling in a car that runs hot? -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Dave Benjamin Sent: Thursday, April 01, 2004 1:05 PM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question My 66 was factory 4 blade fan, rad size with 2 spd and no shroud. Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/ - Original Message - From: John Nasta [EMAIL PROTECTED] To: The Chevelle Mailing List [EMAIL PROTECTED] Sent: Thursday, April 01, 2004 12:53 PM Subject: RE: [Chevelle-list] thermostat question As Brad pointed out, the thermostat has more to do with engine warming than cooling. A fan shroud, a higher volume fan, a smaller WP pulley, or a bigger (or less restricted) radiator would help. John Nasta -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Dave Benjamin Sent: Thursday, April 01, 2004 12:29 PM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question I tried a 160 in my 1966 chevelle and it didn't work very well. There was no fan shroud factory and ounce the motor got up to 160 it wouldn't (open/ close) cycle. It would stay open therefore not very good cooling. The 180 worked fine it it. Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/
RE: [Chevelle-list] thermostat question
When doing a show car and wanting to keep the original look etc. You don't worry about it overheating in traffic, because it is not a driver. As pointed out all too many times already, changing to s higher degree thermostat will not prevent the car from running hot. Calm down, honcho. Thank you, John Nasta -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Dave Benjamin Sent: Thursday, April 01, 2004 11:22 PM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question When doing a show car and wanting to keep the original look etc. You don't add a 7 blade fan, you don't butcher a fan shroud into THE CAR EITHER. I changed the thermostat to keep it running COOL. YES THAT IS MY POINT AND I HOPE IT HELPS YOUR DISCUSSION JOHN Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/
Re: [Chevelle-list] thermostat question
I believe you. Is that connected in any way to this discussion of how to achieve better cooling in a car that runs hot? Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/ - Original Message - From: John Nasta [EMAIL PROTECTED] To: The Chevelle Mailing List [EMAIL PROTECTED] Sent: Thursday, April 01, 2004 11:57 PM Subject: RE: [Chevelle-list] thermostat question When doing a show car and wanting to keep the original look etc. You don't worry about it overheating in traffic, because it is not a driver. As pointed out all too many times already, changing to s higher degree thermostat will not prevent the car from running hot. Calm down, honcho. Thank you, John Nasta -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Dave Benjamin Sent: Thursday, April 01, 2004 11:22 PM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question When doing a show car and wanting to keep the original look etc. You don't add a 7 blade fan, you don't butcher a fan shroud into THE CAR EITHER. I changed the thermostat to keep it running COOL. YES THAT IS MY POINT AND I HOPE IT HELPS YOUR DISCUSSION JOHN Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/
RE: [Chevelle-list] thermostat question
No, but it is connected to YOUR discussion of YOUR car and YOUR beliefs about it. If somebody asks how to keep their car from running hot and I offer free advice to help that person reach his goal, I would hope that the discussion would not be limited to YOUR beliefs about YOUR car. Thank you, John Nasta -Original Message- I believe you. Is that connected in any way to this discussion of how to achieve better cooling in a car that runs hot? Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/ - Original Message - From: John Nasta [EMAIL PROTECTED] To: The Chevelle Mailing List [EMAIL PROTECTED] Sent: Thursday, April 01, 2004 11:57 PM Subject: RE: [Chevelle-list] thermostat question When doing a show car and wanting to keep the original look etc. You don't worry about it overheating in traffic, because it is not a driver. As pointed out all too many times already, changing to s higher degree thermostat will not prevent the car from running hot. Calm down, honcho. Thank you, John Nasta -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Dave Benjamin Sent: Thursday, April 01, 2004 11:22 PM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question When doing a show car and wanting to keep the original look etc. You don't add a 7 blade fan, you don't butcher a fan shroud into THE CAR EITHER. I changed the thermostat to keep it running COOL. YES THAT IS MY POINT AND I HOPE IT HELPS YOUR DISCUSSION JOHN Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/
Re: [Chevelle-list] thermostat question
When I built the 1966 chevelle I built it to be fun and drivable.( because it is not a driver) why build the car. I went to car shows, did poker runs with 30 other hot rods etc. Now that is the reason to drive them. I am not going to be someone who loads there car up on a trailer to go to a show. I DRIVE IT. That is why I had to figure out my cooling problem. SORRY Done now. DaveIngersoll,OntarioMy web site: http://members.tripod.com/benj30/ - Original Message - From: "John Nasta" [EMAIL PROTECTED]To: "The Chevelle Mailing List" [EMAIL PROTECTED]Sent: Thursday, April 01, 2004 11:57 PMSubject: RE: [Chevelle-list] thermostat question When doing a show car and wanting to keep the original look etc. You don't worry about it overheating in traffic, because it is not a driver. As pointed out all too many times already, changing to s higher degree thermostat will not prevent the car from running hot. Calm down, honcho. Thank you, John Nasta -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Dave Benjamin Sent: Thursday, April 01, 2004 11:22 PM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question When doing a show car and wanting to keep the original look etc. You don't add a 7 blade fan, you don't butcher a fan shroud into THE CAR EITHER. I changed the thermostat to keep it running COOL. YES THAT IS MY POINT AND I HOPE IT HELPS YOUR DISCUSSION JOHN Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/
RE: [Chevelle-list] thermostat question
Well, good for you. Hopefully I will be able to answer a question for you some day, and hopefully Jim got some considerable advice about HIS car. Thank you, John Nasta -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]On Behalf Of Dave Benjamin Sent: Friday, April 02, 2004 12:07 AM To: [EMAIL PROTECTED] Subject: Re: [Chevelle-list] thermostat question When I built the 1966 chevelle I built it to be fun and drivable.( because it is not a driver) why build the car. I went to car shows, did poker runs with 30 other hot rods etc. Now that is the reason to drive them. I am not going to be someone who loads there car up on a trailer to go to a show. I DRIVE IT. That is why I had to figure out my cooling problem. SORRY Done now. Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/ - Original Message - From: John Nasta [EMAIL PROTECTED] To: The Chevelle Mailing List [EMAIL PROTECTED] Sent: Thursday, April 01, 2004 11:57 PM Subject: RE: [Chevelle-list] thermostat question When doing a show car and wanting to keep the original look etc. You don't worry about it overheating in traffic, because it is not a driver. As pointed out all too many times already, changing to s higher degree thermostat will not prevent the car from running hot. Calm down, honcho. Thank you, John Nasta -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Dave Benjamin Sent: Thursday, April 01, 2004 11:22 PM To: The Chevelle Mailing List Subject: Re: [Chevelle-list] thermostat question When doing a show car and wanting to keep the original look etc. You don't add a 7 blade fan, you don't butcher a fan shroud into THE CAR EITHER. I changed the thermostat to keep it running COOL. YES THAT IS MY POINT AND I HOPE IT HELPS YOUR DISCUSSION JOHN Dave Ingersoll,Ontario My web site: http://members.tripod.com/benj30/
Re: [Chevelle-List] thermostat recommendations?
Clint, That's what I ran in my FZR600, but then I ran it into the back of a car :-( later Dan McIntosh Pavement Scraping 1964 Impala SS http://www.alloldchevy.com - Original Message - From: Clint Hooper [EMAIL PROTECTED] To: [EMAIL PROTECTED] Sent: Monday, June 30, 2003 12:13 PM Subject: Re: [Chevelle-List] thermostat recommendations? In the summertime when you need maximum cooling,you can reduce the ratio to 75-80% water to 20-25% coolant. As I mentioned before,antifreeze does not dissipate heat as well as pure water. ZR-1's can be hard to cool sometimes so we run 100% distilled water and two bottles of Redline WaterWetter. Clint Hooper LT5 Registry Director http://www.LT5Registry.net/ ACES #1650 http://dalesplace.com/misc/friends/clint_hooper.htm - Original Message - From: Krister Meister [EMAIL PROTECTED] I have always been under the schooling that a 50/50 mix is the happy medium - giving you the best freezing protection and lowest boil over temp at the same time. Anybody else support this logic? Krister Meister Bloomingdale, IL '66 SS #'s matching It's good for about a 10-15 degree drop on an all-aluminum LT5 engine in a ZR-1. Something that works almost as well is drop the ratio of antifreeze to water. Antifreeze doesn't dissipate heat as well as pure water. Clint Hooper LT5 Registry Director http://www.LT5Registry.net/ ACES #1650 http://dalesplace.com/misc/friends/clint_hooper.htm - Original Message - From: [EMAIL PROTECTED] In a message dated 6/28/2003 11:41:12 PM Eastern Daylight Time, [EMAIL PROTECTED] writes: Dan,,,a sure help is to pour in a treatment of water wetter,,it lowers temp by about 30 degrees !!! I have yet to see that stuff work on a big block. Tom - To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED] - To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED] - To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED]
Re: [Chevelle-List] thermostat recommendations?
I have always been under the schooling that a 50/50 mix is the happy medium - giving you the best freezing protection and lowest boil over temp at the same time. Anybody else support this logic? Krister Meister Bloomingdale, IL '66 SS #'s matching It's good for about a 10-15 degree drop on an all-aluminum LT5 engine in a ZR-1. Something that works almost as well is drop the ratio of antifreeze to water. Antifreeze doesn't dissipate heat as well as pure water. Clint Hooper LT5 Registry Director http://www.LT5Registry.net/ ACES #1650 http://dalesplace.com/misc/friends/clint_hooper.htm - Original Message - From: [EMAIL PROTECTED] In a message dated 6/28/2003 11:41:12 PM Eastern Daylight Time, [EMAIL PROTECTED] writes: Dan,,,a sure help is to pour in a treatment of water wetter,,it lowers temp by about 30 degrees !!! I have yet to see that stuff work on a big block. Tom - To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED]
Re: [Chevelle-List] thermostat recommendations?
In the summertime when you need maximum cooling,you can reduce the ratio to 75-80% water to 20-25% coolant. As I mentioned before,antifreeze does not dissipate heat as well as pure water. ZR-1's can be hard to cool sometimes so we run 100% distilled water and two bottles of Redline WaterWetter. Clint Hooper LT5 Registry Director http://www.LT5Registry.net/ ACES #1650 http://dalesplace.com/misc/friends/clint_hooper.htm - Original Message - From: Krister Meister [EMAIL PROTECTED] I have always been under the schooling that a 50/50 mix is the happy medium - giving you the best freezing protection and lowest boil over temp at the same time. Anybody else support this logic? Krister Meister Bloomingdale, IL '66 SS #'s matching It's good for about a 10-15 degree drop on an all-aluminum LT5 engine in a ZR-1. Something that works almost as well is drop the ratio of antifreeze to water. Antifreeze doesn't dissipate heat as well as pure water. Clint Hooper LT5 Registry Director http://www.LT5Registry.net/ ACES #1650 http://dalesplace.com/misc/friends/clint_hooper.htm - Original Message - From: [EMAIL PROTECTED] In a message dated 6/28/2003 11:41:12 PM Eastern Daylight Time, [EMAIL PROTECTED] writes: Dan,,,a sure help is to pour in a treatment of water wetter,,it lowers temp by about 30 degrees !!! I have yet to see that stuff work on a big block. Tom - To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED] - To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED]
Re: [Chevelle-List] thermostat recommendations?
At 11:13 AM 06/30/2003 -0500, you wrote: In the summertime when you need maximum cooling,you can reduce the ratio to 75-80% water to 20-25% coolant. As I mentioned before,antifreeze does not dissipate heat as well as pure water. ZR-1's can be hard to cool sometimes so we run 100% distilled water and two bottles of Redline WaterWetter. Clint Hooper LT5 Registry Director http://www.LT5Registry.net/ ACES #1650 http://dalesplace.com/misc/friends/clint_hooper.htm - Original Message - From: Krister Meister [EMAIL PROTECTED] I have always been under the schooling that a 50/50 mix is the happy medium - giving you the best freezing protection and lowest boil over temp at In TX you can run 60/40 or 65/35 (water to antifreeze) yr round. Like the worst winter here was 10 deg. It depends on where you live if you don't mind changing it come winter. - To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED]
Re: [Chevelle-List] thermostat recommendations?
man, you guys kick butt!! Thanks for all the info, It hasn't been that hot lately, so new news yet... Dan McIntoshPavement Scraping 1964 Impala SShttp://www.alloldchevy.com - Original Message - From: Clint Hooper To: [EMAIL PROTECTED] Sent: Sunday, June 29, 2003 12:09 AM Subject: Re: [Chevelle-List] thermostat recommendations? It's good for about a 10-15 degree drop on an all-aluminum LT5 engine in a ZR-1. Something that works almost as well is drop the ratio of antifreeze to water. Antifreeze doesn't dissipate heat as well as pure water. Clint HooperLT5 Registry Directorhttp://www.LT5Registry.net/ACES #1650http://dalesplace.com/misc/friends/clint_hooper.htm - Original Message - From: [EMAIL PROTECTED] In a message dated 6/28/2003 11:41:12 PM Eastern Daylight Time, [EMAIL PROTECTED] writes: Dan,,,a sure help is to pour in a treatment of water wetter,,it lowers temp by about 30 degrees !!!I have yet to see that stuff work on a big block.Tom
Re: [Chevelle-List] thermostat recommendations?
Dan,,,a sure help is to pour in a treatment of water wetter,,it lowers temp by about 30 degrees !!! - Original Message - From: Mike Holleman To: [EMAIL PROTECTED] Sent: Thursday, June 26, 2003 5:18 PM Subject: Re: [Chevelle-List] thermostat recommendations? Dan, Both guys responding are right. The 350 needs a 180 thermostat. If you have not changed your coolant lately, try a 70/30 mix, distilled water/antifreeze. This will protect you down to around 10 below and will cool better than a higher antifreeze mix ratio. Also, be sure you rad. cap is a high enough pressure cap for your system. I tried a 7 lb cap on my 283 Malibu and it would bypass and dump about a half gallonof coolant when the engine got up to temp. A 13 lb cap cured the problem and keptthe coolant in the rad. to bring my operating temp back below 190. Hope this helps. Mike Holleman Aces #4910 - Original Message - From: Dan McIntosh To: [EMAIL PROTECTED] Sent: Thursday, June 26, 2003 3:58 PM Subject: [Chevelle-List] thermostat recommendations? Howdy.. On the way to a show the other day, my car got up to about 220°F. I think the current thermostat is a 210°F unit... This was in stop and go traffic on a high 80's, low 90's type of day... I am running the stock 5 blade fan, anda full shroud. It is a 1971 El Camino 350 engine.. in a 1964 Impala Is this a common operating temp for this motor? What do you all commonly do to reduce the temp... I used water wetter in my Mustang, and it seemed to work OK, but it could have been the placebo effect... Thanks people! Dan McIntoshPavement Scraping 1964 Impala SShttp://www.alloldchevy.com
Re: [Chevelle-List] thermostat recommendations?
In a message dated 6/28/2003 11:41:12 PM Eastern Daylight Time, [EMAIL PROTECTED] writes: Dan,,,a sure help is to pour in a treatment of water wetter,,it lowers temp by about 30 degrees !!! I have yet to see that stuff work on a big block. Tom
Re: [Chevelle-List] thermostat recommendations?
It's good for about a 10-15 degree drop on an all-aluminum LT5 engine in a ZR-1. Something that works almost as well is drop the ratio of antifreeze to water. Antifreeze doesn't dissipate heat as well as pure water. Clint HooperLT5 Registry Directorhttp://www.LT5Registry.net/ACES #1650http://dalesplace.com/misc/friends/clint_hooper.htm - Original Message - From: [EMAIL PROTECTED] In a message dated 6/28/2003 11:41:12 PM Eastern Daylight Time, [EMAIL PROTECTED] writes: Dan,,,a sure help is to pour in a treatment of water wetter,,it lowers temp by about 30 degrees !!!I have yet to see that stuff work on a big block.Tom
Re: [Chevelle-List] thermostat recommendations?
In a message dated 6/26/2003 2:58:45 PM Eastern Standard Time, [EMAIL PROTECTED] writes: Howdy.. On the way to a show the other day, my car got up to about 220°F. I think the current thermostat is a 210°F unit... This was in stop and go traffic on a high 80's, low 90's type of day... I am running the stock 5 blade fan, and a full shroud. It is a 1971 El Camino 350 engine.. in a 1964 Impala Is this a common operating temp for this motor? What do you all commonly do to reduce the temp... I used water wetter in my Mustang, and it seemed to work OK, but it could have been the placebo effect... Thanks people! Dan McIntosh Pavement Scraping 1964 Impala SS http://www.alloldchevy.com Dan: If all else in your cooling system is OK, the quickest, easiest, cheapest thing to try is a 180 thermostat. 220 is pushing it. Why do you have a 210 in there anyway? based on your current stats this would put you about 190 in traffic which is acceptable in the heat. Water wetter is good too and a mixture of 50/50 water/antifreeze is advisable also. Phil G. 65 SS - To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED]
[Chevelle-List] thermostat recommendations?
Howdy.. On the way to a show the other day, my car got up to about 220°F. I think the current thermostat is a 210°F unit... This was in stop and go traffic on a high 80's, low 90's type of day... I am running the stock 5 blade fan, anda full shroud. It is a 1971 El Camino 350 engine.. in a 1964 Impala Is this a common operating temp for this motor? What do you all commonly do to reduce the temp... I used water wetter in my Mustang, and it seemed to work OK, but it could have been the placebo effect... Thanks people! Dan McIntoshPavement Scraping 1964 Impala SShttp://www.alloldchevy.com
RE: [Chevelle-List] thermostat recommendations?
Dan, Ive always used 180 degree thermostats in my small blocks. Allegedly, a hotter thermostat will offer a little better milage, while colder ones offer better performance. In my not-so-humble opinion, I think 160 stats are too cold for street use, although I know many people do run them. My 400 always runs a little warmer than 180, unless its below 70 degrees out. This morning, caught in that mess on 480 Westbound, where I idled the better part of three miles, my engine never went over 195. I have an electric fan from a GM3.8 FWD. My 72 Elky (stock 350, stock fan shroud) also runs a 180 thermostat and Ive never had any problems with it either, although I dont have a temp gauge. 210 is on the high end of safe. At 220, Id turn the heater on or let the car cool down a bit. As for tips to lower the temp, change the thermostat and make sure the shroud is properly fitted against the radiator. The fan blades should be partially in the shroud. Ive never used Redline Water Wetter before, but have heard of people having success with it on many occasions. Also, while not easy to diagnose, the water pump could be suspect if the impeller blades are corroded away, not circulating as much water as it should. -Dave -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]On Behalf Of Dan McIntosh Sent: Thursday, June 26, 2003 3:59 PM To: [EMAIL PROTECTED] Subject: [Chevelle-List] thermostat recommendations? Howdy.. On the way to a show the other day, my car got up to about 220°F. I think the current thermostat is a 210°F unit... This was in stop and go traffic on a high 80's, low 90's type of day... I am running the stock 5 blade fan, anda full shroud. It is a 1971 El Camino 350 engine.. in a 1964 Impala Is this a common operating temp for this motor? What do you all commonly do to reduce the temp... I used water wetter in my Mustang, and it seemed to work OK, but it could have been the placebo effect... Thanks people! Dan McIntosh Pavement Scraping 1964 Impala SS http://www.alloldchevy.com
RE: [Chevelle-List] thermostat recommendations?
First of all if this is the stock engine 220 deg is too hot. They originally were designed to run around 190 deg and had about 180 deg thermostat in them. The thermostat is really only designed to inhibit the water flow to allow the engine to warm to the normal operating temperature. If you are running within 10 deg of the thermostat rating then your cooling system is probably OK. Try a lower temperature thermostat first and if you still warm up to 220 deg them you need to start troubleshooting your cooling system. If this is a late model engine then they were designed to run at a higher temperature. -Original Message-From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]On Behalf Of Dan McIntoshSent: Thursday, June 26, 2003 12:59 PMTo: [EMAIL PROTECTED]Subject: [Chevelle-List] thermostat recommendations? Howdy.. On the way to a show the other day, my car got up to about 220°F. I think the current thermostat is a 210°F unit... This was in stop and go traffic on a high 80's, low 90's type of day... I am running the stock 5 blade fan, anda full shroud. It is a 1971 El Camino 350 engine.. in a 1964 Impala Is this a common operating temp for this motor? What do you all commonly do to reduce the temp... I used water wetter in my Mustang, and it seemed to work OK, but it could have been the placebo effect... Thanks people! Dan McIntoshPavement Scraping 1964 Impala SShttp://www.alloldchevy.com
Re: [Chevelle-List] thermostat recommendations?
Put a 180 in it. I run a 180 in my 454 in the 70 and in my 350 in my 86 Cutlass. They both hover around 190 degrees unless they are running hard. I just put a 160 in my Cutlass as a temp fix because the stat stuck closed and right now with the 160, it is running too hot becasue the stat is not functioning right in this engine. I have to put a 180 back in it tonight. Tom - To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED]
Re: [Chevelle-List] thermostat recommendations?
Dan, Both guys responding are right. The 350 needs a 180 thermostat. If you have not changed your coolant lately, try a 70/30 mix, distilled water/antifreeze. This will protect you down to around 10 below and will cool better than a higher antifreeze mix ratio. Also, be sure you rad. cap is a high enough pressure cap for your system. I tried a 7 lb cap on my 283 Malibu and it would bypass and dump about a half gallonof coolant when the engine got up to temp. A 13 lb cap cured the problem and keptthe coolant in the rad. to bring my operating temp back below 190. Hope this helps. Mike Holleman Aces #4910 - Original Message - From: Dan McIntosh To: [EMAIL PROTECTED] Sent: Thursday, June 26, 2003 3:58 PM Subject: [Chevelle-List] thermostat recommendations? Howdy.. On the way to a show the other day, my car got up to about 220°F. I think the current thermostat is a 210°F unit... This was in stop and go traffic on a high 80's, low 90's type of day... I am running the stock 5 blade fan, anda full shroud. It is a 1971 El Camino 350 engine.. in a 1964 Impala Is this a common operating temp for this motor? What do you all commonly do to reduce the temp... I used water wetter in my Mustang, and it seemed to work OK, but it could have been the placebo effect... Thanks people! Dan McIntoshPavement Scraping 1964 Impala SShttp://www.alloldchevy.com
Re: [Chevelle-List] thermostat recommendations?
OK, thanks guys... a 180 it is then... I'll see what happens with that.. I have a brand new chrome water pump I was waiting till winter to put on, if the stat doesn't help much, I'll put the pump on and see what happens.. BTW, the shroud is tight, the fan is inside the shroud, and I recently had the rad. flow and pressure tested... Hey Dave... 480 Westbound?? where on the map are you located?? Dan McIntoshPavement Scraping 1964 Impala SShttp://www.alloldchevy.com - Original Message - From: Dave Studly To: [EMAIL PROTECTED] Sent: Thursday, June 26, 2003 4:13 PM Subject: RE: [Chevelle-List] thermostat recommendations? Dan, Ive always used 180 degree thermostats in my small blocks. Allegedly, a hotter thermostat will offer a little better milage, while colder ones offer better performance. In my not-so-humble opinion, I think 160 stats are too cold for street use, although I know many people do run them. My 400 always runs a little warmer than 180, unless its below 70 degrees out. This morning, caught in that mess on 480 Westbound, where I idled the better part of three miles, my engine never went over 195. I have an electric fan from a GM3.8 FWD. My 72 Elky (stock 350, stock fan shroud) also runs a 180 thermostat and Ive never had any problems with it either, although I dont have a temp gauge. 210 is on the high end of safe. At 220, Id turn the heater on or let the car cool down a bit. As for tips to lower the temp, change the thermostat and make sure the shroud is properly fitted against the radiator. The fan blades should be partially in the shroud. Ive never used Redline Water Wetter before, but have heard of people having success with it on many occasions. Also, while not easy to diagnose, the water pump could be suspect if the impeller blades are corroded away, not circulating as much water as it should. -Dave -Original Message-From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]On Behalf Of Dan McIntoshSent: Thursday, June 26, 2003 3:59 PMTo: [EMAIL PROTECTED]Subject: [Chevelle-List] thermostat recommendations? Howdy.. On the way to a show the other day, my car got up to about 220°F. I think the current thermostat is a 210°F unit... This was in stop and go traffic on a high 80's, low 90's type of day... I am running the stock 5 blade fan, anda full shroud. It is a 1971 El Camino 350 engine.. in a 1964 Impala Is this a common operating temp for this motor? What do you all commonly do to reduce the temp... I used water wetter in my Mustang, and it seemed to work OK, but it could have been the placebo effect... Thanks people! Dan McIntoshPavement Scraping 1964 Impala SShttp://www.alloldchevy.com
Re: [Chevelle-List] thermostat recommendations?
Not sure what guages you are using to read the temp, but if it is a mechanical one, you might want to test it (it is fairly easy) to be sure the readings that you are getting are accurate. I struggled with a similar problem years ago and then discovered that my guage was reading 15 degrees high and I really didn't have the problem that I though I had. Just a thought. Gene OK, thanks guys... a 180 it is then... I'll see what happens with that.. I have a brand new chrome water pump I was waiting till winter to put on, if the stat doesn't help much, I'll put the pump on and see what happens.. BTW, the shroud is tight, the fan is inside the shroud, and I recently had the rad. flow and pressure tested... Hey Dave... 480 Westbound?? where on the map are you located?? Dan McIntosh Pavement Scraping 1964 Impala SS http://www.alloldchevy.com - Original Message - Wrom: KBRNVWWCUFPE To: [EMAIL PROTECTED] Sent: Thursday, June 26, 2003 4:13 PM Subject: RE: [Chevelle-List] thermostat recommendations? Dan, I've always used 180 degree thermostats in my small blocks. Allegedly, a hotter thermostat will offer a little better milage, while colder ones offer better performance. In my not-so-humble opinion, I think 160 stats are too cold for street use, although I know many people do run them. My 400 always runs a little warmer than 180, unless it's below 70 degrees out. This morning, caught in that mess on 480 Westbound, where I idled the better part of three miles, my engine never went over 195. I have an electric fan from a GM3.8 FWD. My '72 Elky (stock 350, stock fan shroud) also runs a 180 thermostat and I've never had any problems with it either, although I don't have a temp gauge. 210 is on the high end of safe. At 220, I'd turn the heater on or let the car cool down a bit. As for tips to lower the temp, change the thermostat and make sure the shroud is properly fitted against the radiator. The fan blades should be partially in the shroud. I've never used Redline Water Wetter before, but have heard of people having success with it on many occasions. Also, while not easy to diagnose, the water pump could be suspect if the impeller blades are corroded away, not circulating as much water as it should. -Dave -Original Message- Wrom: GAUTFJMVRESKPNKMBIPBARHDMNNSKVFVWR [mailto:[EMAIL PROTECTED] Behalf Of Dan McIntosh Sent: Thursday, June 26, 2003 3:59 PM To: [EMAIL PROTECTED] Subject: [Chevelle-List] thermostat recommendations? Howdy.. On the way to a show the other day, my car got up to about 220°F. I think the current thermostat is a 210°F unit... This was in stop and go traffic on a high 80's, low 90's type of day... I am running the stock 5 blade fan, and a full shroud. It is a 1971 El Camino 350 engine.. in a 1964 Impala Is this a common operating temp for this motor? What do you all commonly do to reduce the temp... I used water wetter in my Mustang, and it seemed to work OK, but it could have been the placebo effect... Thanks people! Dan McIntosh Pavement Scraping 1964 Impala SS http://www.alloldchevy.com - To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED]
RE: [Chevelle-List] thermostat recommendations?
I live in Lyndhurst, and work in Cleveland on W. 130th between 480 and 71. I know youve mentioned youre a Clevelander, and I remember how shitty the roads were the day you posted about wrecking your truck. 3 Rollover accidents on the freeways today.. yikes. -Dave -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]On Behalf Of Dan McIntosh Sent: Thursday, June 26, 2003 5:36 PM To: [EMAIL PROTECTED] Subject: Re: [Chevelle-List] thermostat recommendations? OK, thanks guys... a 180 it is then... I'll see what happens with that.. I have a brand new chrome water pump I was waiting till winter to put on, if the stat doesn't help much, I'll put the pump on and see what happens.. BTW, the shroud is tight, the fan is inside the shroud, and I recently had the rad. flow and pressure tested... Hey Dave... 480 Westbound?? where on the map are you located?? Dan McIntosh Pavement Scraping 1964 Impala SS http://www.alloldchevy.com - Original Message - From: Dave Studly To: [EMAIL PROTECTED] Sent: Thursday, June 26, 2003 4:13 PM Subject: RE: [Chevelle-List] thermostat recommendations? Dan, Ive always used 180 degree thermostats in my small blocks. Allegedly, a hotter thermostat will offer a little better milage, while colder ones offer better performance. In my not-so-humble opinion, I think 160 stats are too cold for street use, although I know many people do run them. My 400 always runs a little warmer than 180, unless its below 70 degrees out. This morning, caught in that mess on 480 Westbound, where I idled the better part of three miles, my engine never went over 195. I have an electric fan from a GM3.8 FWD. My 72 Elky (stock 350, stock fan shroud) also runs a 180 thermostat and Ive never had any problems with it either, although I dont have a temp gauge. 210 is on the high end of safe. At 220, Id turn the heater on or let the car cool down a bit. As for tips to lower the temp, change the thermostat and make sure the shroud is properly fitted against the radiator. The fan blades should be partially in the shroud. Ive never used Redline Water Wetter before, but have heard of people having success with it on many occasions. Also, while not easy to diagnose, the water pump could be suspect if the impeller blades are corroded away, not circulating as much water as it should. -Dave -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]On Behalf Of Dan McIntosh Sent: Thursday, June 26, 2003 3:59 PM To: [EMAIL PROTECTED] Subject: [Chevelle-List] thermostat recommendations? Howdy.. On the way to a show the other day, my car got up to about 220°F. I think the current thermostat is a 210°F unit... This was in stop and go traffic on a high 80's, low 90's type of day... I am running the stock 5 blade fan, anda full shroud. It is a 1971 El Camino 350 engine.. in a 1964 Impala Is this a common operating temp for this motor? What do you all commonly do to reduce the temp... I used water wetter in my Mustang, and it seemed to work OK, but it could have been the placebo effect... Thanks people! Dan McIntosh Pavement Scraping 1964 Impala SS http://www.alloldchevy.com
Re: [Chevelle-List] Thermostat
ever since I had a problem with a brand new 'stat, I've always tested them...it save taking everything apart again. Plus it reduces the explictives alot!! :) Bill C Ct - To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED]
Re: [Chevelle-List] Thermostat
Well this is the first I've heard of doing it, but it appears that a lot of you do this... guess I'll be doing it too now :) Rodney. 71 Chevelle El Mirage, AZ - Original Message - From: [EMAIL PROTECTED] To: [EMAIL PROTECTED] Sent: Wednesday, September 18, 2002 4:39 AM Subject: Re: [Chevelle-List] Thermostat ever since I had a problem with a brand new 'stat, I've always tested them...it save taking everything apart again. Plus it reduces the explictives alot!! :) Bill C Ct - To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED] - To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED]
Re: [Chevelle-List] Thermostat
You gotta see the look on your wifes face when she comes into the kitchen and finds you standing over a boiling pot of water checking the water temperature with a themometer. When I say I'm working on my car, she just throws up her hands and walks away. But anyhow, you can easily check the openning temperature on a thermostat easily enough. If you look around the kitchen, you can find all the tools you need to do this...or buy your own thermometer. Bill C - To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED]
Re: [Chevelle-List] Thermostat
At 07:44 AM 09/17/2002 -0400, you wrote: You gotta see the look on your wifes face when she comes into the kitchen and finds you standing over a boiling pot of water checking the water temperature with a themometer. When I say I'm working on my car, she just throws up her hands and walks away. But anyhow, you can easily check the openning temperature on a thermostat easily enough. If you look around the kitchen, you can find all the tools you need to do this...or buy your own thermometer. Bill C Yep, I always do that some are 15 to 20 degs off ! - To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED]