ISDN DDR and Routing Protocols [7:47301]
Hy I have a ISDN Dial up and dont want have any Routing Protocol over it. What is the right access-list, and which features should you Block over the ISDN link. access-list 101 permit icmp 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 ( or any any ) access-list 101 deny Tcp 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 eq bgp ( or 179 ) access-list 101 permit ip 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 ip access-group 101 out ( on the BRI interface both sites ) no cdp enable ( is this nessecary? ) passiv-interface BRI 0 ( on specific Routing process ) is this enough to stop all the Routing Protocols over the ISDN link or missed I something Thanks for Help Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=47301&t=47301 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
IPX and Timers [7:52850]
Hy guys I have a problem with the IPX timers, if I would change the IPX eigrp hold-time , I can do this with ipx hold-time inteval ... command, other possibility is to change the ipx hello interval , that should work but in all the possibility that I tryed out it will not work. Ciscos statement is if the hold time is smaller then twice a hello interval , the timers should be synchronize. ( will not work ) any ideas are VERY welcome. Other if i change the Hold time of 60 seconds on a ethernet , the ipx hello interval will stay on 5 seconds , no synch?? now if someone cxan help me to get this question answered , that would be super. Regards Philipp PS: Already tryed several IOS version. Not work Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=52850&t=52850 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: IPX and Timers [7:52850]
Hy I also know on my Lab , and i already tryed out to have the same timers on al interfaces within the AS, but no success. I created a very small AS. Router---Et0Et1---Router the whole is ipx router eig 200 , ipx network 100 ipx rip is off But it still do not synchronize the ipx timers. What I do wrong?? Regards philipp -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Hello Goodbye Sent: Samstag, 7. September 2002 20:37 To: [EMAIL PROTECTED] Subject: Re: IPX and Timers [7:52850] First, have you made sure that all the hello and hold times are the same on all interfaces on all routers in the AS. http://www.cisco.com/univercd/cc/td/doc/cisintwk/itg_v1/tr1908.htm#xtocid15 The default hold time is 3 times the hello time. Is there any reason to not keep this relationship? I'm going to play with this in my lab this weekend to verify that all the timers need to be set the same but I have a feeling that DUAL will get messed up if they are not. Ben --- hagedorn wrote: > Hy guys > > I have a problem with the IPX timers, if I would > change the IPX eigrp > hold-time , I can do this with ipx hold-time inteval > ... command, other > possibility is to change the ipx hello interval , > that should work but in > all the possibility that I tryed out it will not > work. > Ciscos statement is if the hold time is > smaller then twice a hello > interval , the timers should be synchronize. ( will > not work ) any ideas are > VERY welcome. > Other if i change the Hold time of 60 seconds on a > ethernet , the ipx hello > interval will stay on 5 seconds , no synch?? > now if someone cxan help me to get this question > answered , that would be > super. > > Regards Philipp > > PS: Already tryed several IOS version. Not work [EMAIL PROTECTED] __ Do You Yahoo!? Yahoo! Finance - Get real-time stock quotes http://finance.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=52885&t=52850 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: IPX and Timers [7:52850]
hy here are the cisco statement. Regards Philipp ipx hold-time eigrp To specify the length of time a neighbor should consider IPX enhanced IGRP hello packets valid, use the ipx hold-time eigrp interface configuration command. To restore the default time, use the no form of this command. ipx hold-time eigrp autonomous-system-number seconds no ipx hold-time eigrp autonomous-system-number seconds Syntax Description autonomous-system-numberIPX enhanced IGRP autonomous system number. It can be a decimal integer from 1 to 65535. seconds Hold time, in seconds. The hold time is advertised in hello packets and indicates to neighbors the length of time they should consider the sender valid. The default hold time is 15 seconds, which is three times the hello interval. Default 15 seconds Command Mode Interface configuration Usage Guidelines If the current value for the hold time is less than two times the interval between hello packets, the hold time will be reset to three times the hello interval. If a router does not receive a hello packet within the specified hold time, routes through the router are considered available. Increasing the hold time delays route convergence across the network. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Hello Goodbye Sent: Montag, 9. September 2002 06:41 To: [EMAIL PROTECTED] Subject: RE: IPX and Timers [7:52850] I tried to update just one of the ipx eigrp timers and found the other did not update as well. I'm not thinking that this can be done in eigrp. I just dont see how they would ever synchronize in eigrp. With IPX RIP you can change the update interval and the time it takes the route to be marked invalid will update with this. You can change the ratio with the ipx rip-multiplier command. I have been unable to figure anything like this out for eigrp. Where did you read or hear otherwise? Ben --- hagedorn wrote: > Hy > > I also know on my Lab , and i already tryed out to > have the same timers on > al interfaces within the AS, but no success. > I created a very small AS. > > Router---Et0Et1---Router > > the whole is ipx router eig 200 , ipx network 100 > ipx rip is off > > But it still do not synchronize the ipx timers. What > I do wrong?? > Regards philipp > > -Original Message- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED]]On Behalf Of > Hello Goodbye > Sent: Samstag, 7. September 2002 20:37 > To: [EMAIL PROTECTED] > Subject: Re: IPX and Timers [7:52850] > > > First, have you made sure that all the hello and > hold > times are the same on all interfaces on all routers > in > the AS. > > http://www.cisco.com/univercd/cc/td/doc/cisintwk/itg_v1/tr1908.htm#xtocid15 > > The default hold time is 3 times the hello time. Is > there any reason to not keep this relationship? > > I'm going to play with this in my lab this weekend > to > verify that all the timers need to be set the same > but > I have a feeling that DUAL will get messed up if > they > are not. > > Ben > > --- hagedorn wrote: > > Hy guys > > > > I have a problem with the IPX timers, if I would > > change the IPX eigrp > > hold-time , I can do this with ipx hold-time > inteval > > ... command, other > > possibility is to change the ipx hello interval , > > that should work but in > > all the possibility that I tryed out it will not > > work. > > Ciscos statement is if the hold time is > > smaller then twice a hello > > interval , the timers should be synchronize. ( > will > > not work ) any ideas are > > VERY welcome. > > Other if i change the Hold time of 60 seconds on a > > ethernet , the ipx hello > > interval will stay on 5 seconds , no synch?? > > now if someone cxan help me to get this question > > answered , that would be > > super. > > > > Regards Philipp > > > > PS: Already tryed several IOS version. Not work > [EMAIL PROTECTED] > > > __ > Do You Yahoo!? > Yahoo! Finance - Get real-time stock quotes > http://finance.yahoo.com [EMAIL PROTECTED] __ Do You Yahoo!? Yahoo! Finance - Get real-time stock quotes http://finance.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=52956&t=52850 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
DHCP on Ethernet or Fastethernet [7:17690]
How Can someone help me how i can configured a ethernet or a fastethernet interface as a DHCP client, for that the interface gets a ip address from the DHCP server. This is actually a new features but i dont know on which IOS version. When someone has a idea that would be very great. Regards philipp Philipp Hagedorn Network Integration System Engineer CCNP / VOICE/ IP Telephony Tel:+41 (0) 1 839 19 17 Mobile: +41 (0) 76 382 14 59 mailto:[EMAIL PROTECTED] Getronics (Schweiz) AG Industriestrasse 50a CH-8304 Wallisellen Tel:+41 (0) 1 839 16 11 Fax:+41 (0) 1 839 17 85 URL:http://www.getronics.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=17690&t=17690 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
