RE: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129]
Resolved!!! Turns out our equipment provider sent us the wrong cable They sent the HSSI Null Modem cable (CAB-HNUL) and not the CAB-HSI1! Thanks for everyone's insight. Cheers, MKJ -Original Message- From: Jablonski, Michael [mailto:[EMAIL PROTECTED] Sent: Wednesday, July 30, 2003 8:56 AM To: [EMAIL PROTECTED] Subject: RE: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129] Yeah it's a HSSI cable... CAB-HSI1 is the part. Telco is using the default HDLC for encapsulation. I've got telco coming out today to test the line. According to Kentrox's doc, a T3 w/HSSI interface has an allowed range of 1-35MHz; or 45 if both are set to 45MHz. I currently have the transmit and receive set at 12MHz. Below is the "sh contr hssi1/0" Interesting, received clockrate says 1582! Shouldn't that be 12000? M1T-HSSI-B: show controller: PAS unit 0, subunit 0, f/w version 3-92, rev ID 0x281, version 3 idb = 0x621D1178, ds = 0x621D2E70, ssb=0x621D31A4 Clock mux=0x31, ucmd_ctrl=0x8, port_status=0x5 Serial config=0x8, line config=0x1B0202, rx line config=0x80202 maxdgram=4584, bufpool=128Kb, 120 particles LC=down CA=down TM=down LB=down TA=up LA=down line state: down HSSI DTE, received clockrate 1582 base0 registers=0x3C80, base1 registers=0x3C802000 rx_base0 registers=0x3C90, rx_base1 registers=0x3C902000 mxt_ds=0x62684E5C, rx ring entries=124, tx ring entries=126 statring=0x7CD1FA0, statr shadow=0x621D39AC, stat_head=0 plus_pa: rx_statring=0x7CD21E0, rx_statr shadow=0x621D3DD8, rx_stat_head=0 rxring=0x7CD1D60, rxr shadow=0x621D3380, rx_head=0 txring=0x7CD27A0, txr shadow=0x621D4204, tx_head=0, tx_tail=0, tx_count=0 throttled=0, enabled=0 halted=0, last halt reason=0 Microcode fatal errors=0 rx_no_eop_err=0, rx_no_stp_err=0, rx_no_eop_stp_err=0 rx_no_buf=0, rx_soft_overrun_err=0, dump_err= 0, bogus=0, mxt_flags=0xC tx_underrun_err=0, tx_soft_underrun_err=0, tx_limited=0(126) tx_fullring=0, tx_started=0 rx_int_count=0, tx_int_count=0 Thanks for all your input Cheers, Mike J -Original Message- From: s vermill [mailto:[EMAIL PROTECTED] Sent: Tuesday, July 29, 2003 2:30 PM To: [EMAIL PROTECTED] Subject: RE: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129] Jablonski, Michael wrote: > > Has anyone had any experience w/the following combination? > > 3640 & NM-1HSSI & Kentrox DataSMART T3/E3 IDSU > > I've been trying, to no avail, to bring the HSSI up for a 12M > DS3 The > CSU/DSU, according to the lights, is ready to send and receive > data; but > when I bring up the int on the router, it shows down down. Are you sure you have a HSSI cable? SCSI 2 will physically fit the connectors, but is pinned out very differently. Make sure that's good to go... > Here's the > router info: > ~~~ > interface Hssi1/0 > bandwidth 12000 > ip address x.x.x.x 255.255.255.252 > serial restart_delay 0 > no cdp enable > > Hssi1/0 is down, line protocol is down > Hardware is M1T-HSSI-B > Internet address is x.x.x.x/30 > MTU 4470 bytes, BW 12000 Kbit, DLY 200 usec, > reliability 255/255, txload 1/255, rxload 1/255 > Encapsulation HDLC, crc 16, loopback not set > Keepalive set (10 sec) > Restart-Delay is 0 secs > Last input never, output never, output hang never > Last clearing of "show interface" counters never > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output > drops: 0 > Queueing strategy: fifo > Output queue :0/40 (size/max) > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 0 bits/sec, 0 packets/sec > 0 packets input, 0 bytes, 0 no buffer > Received 0 broadcasts, 0 runts, 0 giants, 0 throttles > 0 parity > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 > abort > 0 packets output, 0 bytes, 0 underruns > 0 output errors, 0 applique, 8 interface resets > 0 output buffer failures, 0 output buffers swapped out > 13 carrier transitions LC=down CA=down TM=down > LB=down TA=up > LA=down Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=73247&t=73129 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129]
Yeah it's a HSSI cable... CAB-HSI1 is the part. Telco is using the default HDLC for encapsulation. I've got telco coming out today to test the line. According to Kentrox's doc, a T3 w/HSSI interface has an allowed range of 1-35MHz; or 45 if both are set to 45MHz. I currently have the transmit and receive set at 12MHz. Below is the "sh contr hssi1/0" Interesting, received clockrate says 1582! Shouldn't that be 12000? M1T-HSSI-B: show controller: PAS unit 0, subunit 0, f/w version 3-92, rev ID 0x281, version 3 idb = 0x621D1178, ds = 0x621D2E70, ssb=0x621D31A4 Clock mux=0x31, ucmd_ctrl=0x8, port_status=0x5 Serial config=0x8, line config=0x1B0202, rx line config=0x80202 maxdgram=4584, bufpool=128Kb, 120 particles LC=down CA=down TM=down LB=down TA=up LA=down line state: down HSSI DTE, received clockrate 1582 base0 registers=0x3C80, base1 registers=0x3C802000 rx_base0 registers=0x3C90, rx_base1 registers=0x3C902000 mxt_ds=0x62684E5C, rx ring entries=124, tx ring entries=126 statring=0x7CD1FA0, statr shadow=0x621D39AC, stat_head=0 plus_pa: rx_statring=0x7CD21E0, rx_statr shadow=0x621D3DD8, rx_stat_head=0 rxring=0x7CD1D60, rxr shadow=0x621D3380, rx_head=0 txring=0x7CD27A0, txr shadow=0x621D4204, tx_head=0, tx_tail=0, tx_count=0 throttled=0, enabled=0 halted=0, last halt reason=0 Microcode fatal errors=0 rx_no_eop_err=0, rx_no_stp_err=0, rx_no_eop_stp_err=0 rx_no_buf=0, rx_soft_overrun_err=0, dump_err= 0, bogus=0, mxt_flags=0xC tx_underrun_err=0, tx_soft_underrun_err=0, tx_limited=0(126) tx_fullring=0, tx_started=0 rx_int_count=0, tx_int_count=0 Thanks for all your input Cheers, Mike J -Original Message- From: s vermill [mailto:[EMAIL PROTECTED] Sent: Tuesday, July 29, 2003 2:30 PM To: [EMAIL PROTECTED] Subject: RE: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129] Jablonski, Michael wrote: > > Has anyone had any experience w/the following combination? > > 3640 & NM-1HSSI & Kentrox DataSMART T3/E3 IDSU > > I've been trying, to no avail, to bring the HSSI up for a 12M > DS3 The > CSU/DSU, according to the lights, is ready to send and receive > data; but > when I bring up the int on the router, it shows down down. Are you sure you have a HSSI cable? SCSI 2 will physically fit the connectors, but is pinned out very differently. Make sure that's good to go... > Here's the > router info: > ~~~ > interface Hssi1/0 > bandwidth 12000 > ip address x.x.x.x 255.255.255.252 > serial restart_delay 0 > no cdp enable > > Hssi1/0 is down, line protocol is down > Hardware is M1T-HSSI-B > Internet address is x.x.x.x/30 > MTU 4470 bytes, BW 12000 Kbit, DLY 200 usec, > reliability 255/255, txload 1/255, rxload 1/255 > Encapsulation HDLC, crc 16, loopback not set > Keepalive set (10 sec) > Restart-Delay is 0 secs > Last input never, output never, output hang never > Last clearing of "show interface" counters never > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output > drops: 0 > Queueing strategy: fifo > Output queue :0/40 (size/max) > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 0 bits/sec, 0 packets/sec > 0 packets input, 0 bytes, 0 no buffer > Received 0 broadcasts, 0 runts, 0 giants, 0 throttles > 0 parity > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 > abort > 0 packets output, 0 bytes, 0 underruns > 0 output errors, 0 applique, 8 interface resets > 0 output buffer failures, 0 output buffers swapped out > 13 carrier transitions LC=down CA=down TM=down > LB=down TA=up > LA=down Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=73239&t=73129 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129]
Jablonski, Michael wrote: > > Has anyone had any experience w/the following combination? > > 3640 & NM-1HSSI & Kentrox DataSMART T3/E3 IDSU > > I've been trying, to no avail, to bring the HSSI up for a 12M > DS3 The > CSU/DSU, according to the lights, is ready to send and receive > data; but > when I bring up the int on the router, it shows down down. Are you sure you have a HSSI cable? SCSI 2 will physically fit the connectors, but is pinned out very differently. Make sure that's good to go... > Here's the > router info: > ~~~ > interface Hssi1/0 > bandwidth 12000 > ip address x.x.x.x 255.255.255.252 > serial restart_delay 0 > no cdp enable > > Hssi1/0 is down, line protocol is down > Hardware is M1T-HSSI-B > Internet address is x.x.x.x/30 > MTU 4470 bytes, BW 12000 Kbit, DLY 200 usec, > reliability 255/255, txload 1/255, rxload 1/255 > Encapsulation HDLC, crc 16, loopback not set > Keepalive set (10 sec) > Restart-Delay is 0 secs > Last input never, output never, output hang never > Last clearing of "show interface" counters never > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output > drops: 0 > Queueing strategy: fifo > Output queue :0/40 (size/max) > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 0 bits/sec, 0 packets/sec > 0 packets input, 0 bytes, 0 no buffer > Received 0 broadcasts, 0 runts, 0 giants, 0 throttles > 0 parity > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 > abort > 0 packets output, 0 bytes, 0 underruns > 0 output errors, 0 applique, 8 interface resets > 0 output buffer failures, 0 output buffers swapped out > 13 carrier transitions LC=down CA=down TM=down > LB=down TA=up > LA=down > > Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=73193&t=73129 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129]
Check the linespeed - from memory the kentrox is pretty limited to what data rate you can specify. If the other end (ISP end) is Cisco, you can ask them to change it to match yours. -Original Message- From: John Neiberger [mailto:[EMAIL PROTECTED] Sent: 29 July 2003 15:30 To: [EMAIL PROTECTED] Subject: Re: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129] Mike, I'd try replacing the cable first if you have one available. Even if the DS3 isn't configured correctly your interface should be up if you're router is speaking to your IDSU. I'd also try resetting the IDSU to its defaults just to make sure something in the config on the IDSU isn't breaking communication with the router. If the serial line comes up at that point you'll know it's a config issue. It's been a while since I even looked at an IDSU (even though we have almost an identical setup) and I don't recall what options are available so I might be way off base. If I can find the documentation I'll take a look at it and see if anything else comes to mind. Regards, John >>> Jablonski, Michael 7/28/03 5:06:53 PM >>> Has anyone had any experience w/the following combination? 3640 & NM-1HSSI & Kentrox DataSMART T3/E3 IDSU I've been trying, to no avail, to bring the HSSI up for a 12M DS3 The CSU/DSU, according to the lights, is ready to send and receive data; but when I bring up the int on the router, it shows down down. Here's the router info: ~~~ interface Hssi1/0 bandwidth 12000 ip address x.x.x.x 255.255.255.252 serial restart_delay 0 no cdp enable Hssi1/0 is down, line protocol is down Hardware is M1T-HSSI-B Internet address is x.x.x.x/30 MTU 4470 bytes, BW 12000 Kbit, DLY 200 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation HDLC, crc 16, loopback not set Keepalive set (10 sec) Restart-Delay is 0 secs Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue :0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 parity 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 applique, 8 interface resets 0 output buffer failures, 0 output buffers swapped out 13 carrier transitions LC=down CA=down TM=down LB=down TA=up LA=down === This message has been checked for all known viruses by the Sirocom Virus Scanning Service === === This message has been checked for all known viruses by the Sirocom Virus Scanning Service WWW.SIROCOM.COM === Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=73180&t=73129 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129]
Mike, I'd try replacing the cable first if you have one available. Even if the DS3 isn't configured correctly your interface should be up if you're router is speaking to your IDSU. I'd also try resetting the IDSU to its defaults just to make sure something in the config on the IDSU isn't breaking communication with the router. If the serial line comes up at that point you'll know it's a config issue. It's been a while since I even looked at an IDSU (even though we have almost an identical setup) and I don't recall what options are available so I might be way off base. If I can find the documentation I'll take a look at it and see if anything else comes to mind. Regards, John >>> Jablonski, Michael 7/28/03 5:06:53 PM >>> Has anyone had any experience w/the following combination? 3640 & NM-1HSSI & Kentrox DataSMART T3/E3 IDSU I've been trying, to no avail, to bring the HSSI up for a 12M DS3 The CSU/DSU, according to the lights, is ready to send and receive data; but when I bring up the int on the router, it shows down down. Here's the router info: ~~~ interface Hssi1/0 bandwidth 12000 ip address x.x.x.x 255.255.255.252 serial restart_delay 0 no cdp enable Hssi1/0 is down, line protocol is down Hardware is M1T-HSSI-B Internet address is x.x.x.x/30 MTU 4470 bytes, BW 12000 Kbit, DLY 200 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation HDLC, crc 16, loopback not set Keepalive set (10 sec) Restart-Delay is 0 secs Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue :0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 parity 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 applique, 8 interface resets 0 output buffer failures, 0 output buffers swapped out 13 carrier transitions LC=down CA=down TM=down LB=down TA=up LA=down Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=73170&t=73129 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129]
FWIW, here is a current working config, 3640 to a Kentrox. If you have the cable connected and the CSU powered you should get an up/down state. interface Hssi3/0 description to Qwest x ip address x.x.x.x 255.255.255.252 encapsulation ppp load-interval 30 serial restart-delay 0 Dave Jablonski, Michael wrote: > Has anyone had any experience w/the following combination? > > 3640 & NM-1HSSI & Kentrox DataSMART T3/E3 IDSU > > I've been trying, to no avail, to bring the HSSI up for a 12M DS3 The > CSU/DSU, according to the lights, is ready to send and receive data; but > when I bring up the int on the router, it shows down down. Here's the > router info: > ~~~ > interface Hssi1/0 > bandwidth 12000 > ip address x.x.x.x 255.255.255.252 > serial restart_delay 0 > no cdp enable > > Hssi1/0 is down, line protocol is down > Hardware is M1T-HSSI-B > Internet address is x.x.x.x/30 > MTU 4470 bytes, BW 12000 Kbit, DLY 200 usec, > reliability 255/255, txload 1/255, rxload 1/255 > Encapsulation HDLC, crc 16, loopback not set > Keepalive set (10 sec) > Restart-Delay is 0 secs > Last input never, output never, output hang never > Last clearing of "show interface" counters never > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 > Queueing strategy: fifo > Output queue :0/40 (size/max) > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 0 bits/sec, 0 packets/sec > 0 packets input, 0 bytes, 0 no buffer > Received 0 broadcasts, 0 runts, 0 giants, 0 throttles > 0 parity > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort > 0 packets output, 0 bytes, 0 underruns > 0 output errors, 0 applique, 8 interface resets > 0 output buffer failures, 0 output buffers swapped out > 13 carrier transitions LC=down CA=down TM=down LB=down TA=up > LA=down -- David Madland CCIE# 2016 Sr. Network Engineer Qwest Communications 612-664-3367 "Government can do something for the people only in proportion as it can do something to the people." -- Thomas Jefferson Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=73169&t=73129 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129]
What does the physical layer say? sh controller (intf) Martijn -Oorspronkelijk bericht- Van: Jablonski, Michael [mailto:[EMAIL PROTECTED] Verzonden: dinsdag 29 juli 2003 0:24 Aan: [EMAIL PROTECTED] Onderwerp: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129] Has anyone had any experience w/the following combination? 3640 & NM-1HSSI & Kentrox DataSMART T3/E3 IDSU I've been trying, to no avail, to bring the HSSI up for a 12M DS3 The CSU/DSU, according to the lights, is ready to send and receive data; but when I bring up the int on the router, it shows down down. Here's the router info: ~~~ interface Hssi1/0 bandwidth 12000 ip address x.x.x.x 255.255.255.252 serial restart_delay 0 no cdp enable Hssi1/0 is down, line protocol is down Hardware is M1T-HSSI-B Internet address is x.x.x.x/30 MTU 4470 bytes, BW 12000 Kbit, DLY 200 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation HDLC, crc 16, loopback not set Keepalive set (10 sec) Restart-Delay is 0 secs Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue :0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 parity 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 applique, 8 interface resets 0 output buffer failures, 0 output buffers swapped out 13 carrier transitions LC=down CA=down TM=down LB=down TA=up LA=down Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=73144&t=73129 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129] (2) [7:73145]
What encap did you agree on, I see that you left the default on? Also some eletronics should be working because of the interface resets etc? (clear the counters just for the statistics). Replace the cable and caal the provider to test the line until the modem? Martijn Jansen OCN WAN Maatwerk Levering *070 - 44 12285 * [EMAIL PROTECTED] -Oorspronkelijk bericht- Van: Jablonski, Michael [mailto:[EMAIL PROTECTED] Verzonden: dinsdag 29 juli 2003 0:24 Aan: [EMAIL PROTECTED] Onderwerp: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129] Has anyone had any experience w/the following combination? 3640 & NM-1HSSI & Kentrox DataSMART T3/E3 IDSU I've been trying, to no avail, to bring the HSSI up for a 12M DS3 The CSU/DSU, according to the lights, is ready to send and receive data; but when I bring up the int on the router, it shows down down. Here's the router info: ~~~ interface Hssi1/0 bandwidth 12000 ip address x.x.x.x 255.255.255.252 serial restart_delay 0 no cdp enable Hssi1/0 is down, line protocol is down Hardware is M1T-HSSI-B Internet address is x.x.x.x/30 MTU 4470 bytes, BW 12000 Kbit, DLY 200 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation HDLC, crc 16, loopback not set Keepalive set (10 sec) Restart-Delay is 0 secs Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue :0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 parity 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 applique, 8 interface resets 0 output buffer failures, 0 output buffers swapped out 13 carrier transitions LC=down CA=down TM=down LB=down TA=up LA=down Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=73145&t=73145 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129]
Don't you need clock on serials? /Nadeem Jablonski, Michael wrote: >Has anyone had any experience w/the following combination? > >3640 & NM-1HSSI & Kentrox DataSMART T3/E3 IDSU > >I've been trying, to no avail, to bring the HSSI up for a 12M DS3 The >CSU/DSU, according to the lights, is ready to send and receive data; but >when I bring up the int on the router, it shows down down. Here's the >router info: >~~~ >interface Hssi1/0 > bandwidth 12000 > ip address x.x.x.x 255.255.255.252 > serial restart_delay 0 > no cdp enable > >Hssi1/0 is down, line protocol is down > Hardware is M1T-HSSI-B > Internet address is x.x.x.x/30 > MTU 4470 bytes, BW 12000 Kbit, DLY 200 usec, > reliability 255/255, txload 1/255, rxload 1/255 > Encapsulation HDLC, crc 16, loopback not set > Keepalive set (10 sec) > Restart-Delay is 0 secs > Last input never, output never, output hang never > Last clearing of "show interface" counters never > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 > Queueing strategy: fifo > Output queue :0/40 (size/max) > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 0 bits/sec, 0 packets/sec > 0 packets input, 0 bytes, 0 no buffer > Received 0 broadcasts, 0 runts, 0 giants, 0 throttles > 0 parity > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort > 0 packets output, 0 bytes, 0 underruns > 0 output errors, 0 applique, 8 interface resets > 0 output buffer failures, 0 output buffers swapped out > 13 carrier transitions LC=down CA=down TM=down LB=down TA=up >LA=down Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=73137&t=73129 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129]
Has anyone had any experience w/the following combination? 3640 & NM-1HSSI & Kentrox DataSMART T3/E3 IDSU I've been trying, to no avail, to bring the HSSI up for a 12M DS3 The CSU/DSU, according to the lights, is ready to send and receive data; but when I bring up the int on the router, it shows down down. Here's the router info: ~~~ interface Hssi1/0 bandwidth 12000 ip address x.x.x.x 255.255.255.252 serial restart_delay 0 no cdp enable Hssi1/0 is down, line protocol is down Hardware is M1T-HSSI-B Internet address is x.x.x.x/30 MTU 4470 bytes, BW 12000 Kbit, DLY 200 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation HDLC, crc 16, loopback not set Keepalive set (10 sec) Restart-Delay is 0 secs Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue :0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 parity 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 applique, 8 interface resets 0 output buffer failures, 0 output buffers swapped out 13 carrier transitions LC=down CA=down TM=down LB=down TA=up LA=down Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=73129&t=73129 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]