RE: Frame-Relay issue [7:63446]
ISP and verify your Frame Relay configuration parameters. (LMI-Type, DLCI, etc.) On the No Shut command, I'd use it last on each interface you configure. -Mark -Original Message- From: Monu Sekhon [mailto:[EMAIL PROTECTED] Sent: Thursday, February 20, 2003 7:40 PM To: [EMAIL PROTECTED] Subject: Re: Frame-Relay issue [7:63446] Hi Larry/John, I forgot to mention no shut in the above confif while writing here, Its still there and connection does not come out See I mentioned that while giving command by command manually connection comes out. It seems to me that while the interface is down during that frame-relay LMIs think that interface is down and make the link down. I am rather confused.I dont know but this is happening. again writing config: -- interface Serial0 shut (if i give here no shut then link comes up at one go) encapsulation frame-relay frame-relay lmi-type cisco no shut exit interface Serial0/0.1 point-to-point no shutdown ip address 1.1.1.1 255.255.255.0 frame-relay interface-dlci 108 exit and also John try these in your router but at one go the interface will not come up as far i know .I agree with ur confguration and mine is also correct .Its said by Prisicilla and others that shutting a interface is good practise while configuring encap types.This i read in one of the previous Posts. so can u all reply what is the problem here in show ip interface it shows as protocol down , physical link up. sh frame-relay pvs shows as inactive.no lmi are exchanged. any help will be appreciated. - Larry Letterman wrote: enter the no shut command into your cut and paste script for the Int Ser0 and it will come up..all interfaces in a router are always defaulted to shutdown..In your case the Main interface needs to be no shut in order for the logical interface to work... -- Larry Letterman Network Engineer Cisco Systems Monu Sekhon wrote in message news:[EMAIL PROTECTED] Hi All Hey I am facing a strange problem in frame-relay My config -- my initial config int serial 0 (nothing confgured initially) Then I cut paste this config and my link does not come up means Interface does not come up. interface Serial0 shut (if i give here no shut then link comes up at one go) encapsulation frame-relay frame-relay lmi-type cisco exit interface Serial0/0.1 point-to-point no shutdown ip address 1.1.1.1 255.255.255.0 frame-relay interface-dlci 108 exit I have to do shut and no shut on main interface why ? if the above commands i execute one by one then the link comes up. Is it a differnece between pasting the config at one go or what when i give command single by single. I enable debugging for frame-relay packets and it shows encap faiiled once only on the above sub interface.is anything frame-relay lmis has anything to do. I am very confused. Thanx in advance [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=64027t=63446 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Frame-Relay issue [7:63446]
Hi Monu I tried the configuration given by you. But i didnt find any problem in bringing up the interface when i cut and paste the configuration. Here is the config when i cut n paste the config from a text file yourname(config)#interface Serial1/1 yourname(config-if)#shut yourname(config-if)#encapsulation frame-relay yourname(config-if)#frame-relay lmi-type cisco yourname(config-if)#no shut yourname(config-if)#exit yourname(config)#interface Serial1/1.1 point-to-point yourname(config-subif)#no shutdown yourname(config-subif)#ip address 20.20.20.11 255.255.255.0 yourname(config-subif)#frame-relay interface-dlci 108 yourname(config-fr-dlci)#exit yourname(config-subif)# yourname(config-subif)# *Mar 1 00:48:19.271: %LINK-3-UPDOWN: Interface Serial1/1, changed state to up yourname(config-subif)# yourname(config-subif)# yourname(config-subif)# yourname(config-subif)#^Z yourname# yourname# *Mar 1 00:48:28.811: %SYS-5-CONFIG_I: Configured from console by console yourname# yourname#sh ip int brief *Mar 1 00:48:30.271: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/1, changed state to up Interface IP-Address OK? Method Status Prot ocol FastEthernet0/0172.20.110.8YES manual up up FastEthernet0/1unassigned YES unset up down ATM0/0 unassigned YES unset up up ATM0/1 unassigned YES unset up up Serial1/0 unassigned YES unset down down Serial1/0.1unassigned YES manual deleted down Serial1/1 unassigned YES unset up up Serial1/1.120.20.20.11 YES manual up up Serial1/2 unassigned YES unset down down FastEthernet1/0unassigned YES unset up down FastEthernet1/1unassigned YES unset up down yourname# Please let me know ur comments Regards Deepak Priscilla Oppenheimer wrote: There's obviously no good answer to why there are no problems bringing the link up/up when you type in the commands one by one but there are problems when you copy and paste them. Here are some suggestions, though: 1) You work for Cisco. Report it as a bug. 2) The copy and paste is corrupting a character, forgetting to do carriage return or something of that nature. Do all the commands end up the in the running config? 3) There's some sort of timing issue. To fix the problem: Don't do copy and paste that fast. :-) Priscilla Monu Sekhon wrote: Hi Mark, Thanx for reply.but I mentioned that when we do shut no shut again link comes up.no dlci, no lmi problem: I am testing in lab setup two rouetrs connnected to frame-relay cloud Please do help anybody in this regard, why the link doesnot come at one instant why it requiers again shut and no shut, when i copy paste the config and when i give command by command then without gving shut and noshut the link comes up. Mark W. Odette II wrote: in show ip interface it shows as protocol down , physical link up. sh frame-relay pvs shows as inactive.no lmi are exchanged. Usually Protocol Down, Link Up indicates that you have mismatched encapsulation, LMI-Type, or even incorrect IP Addressing (wrong Subnet or incorrect Subnet Mask) between your end and the other end of the FR Network. If no LMI is exchanged, then the LMI-Type is incorrect between that Serial Interface and the Service Provider Frame Switch. If this is a Frame Relay LAB setup, double-check your Frame Relay Switch configuration. If this is a Production Setup, contact your ISP and verify your Frame Relay configuration parameters. (LMI-Type, DLCI, etc.) On the No Shut command, I'd use it last on each interface you configure. -Mark -Original Message- From: Monu Sekhon [mailto:[EMAIL PROTECTED] Sent: Thursday, February 20, 2003 7:40 PM To: [EMAIL PROTECTED] Subject: Re: Frame-Relay issue [7:63446] Hi Larry/John, I forgot to mention no shut in the above confif while writing here, Its still there and connection does not come out See I mentioned that while giving command by command manually connection comes out. It seems to me that while the interface is down during that frame-relay LMIs think that interface is down and make the link down. I am rather confused.I dont know but this is happening. again writing config: -- interface Serial0 shut (if i give here no shut then link comes up at one go) encapsulation frame-relay frame-relay lmi-type cisco no shut exit interface Serial0/0.1 point-to-point
RE: Frame-Relay issue [7:63446]
Hi Mark, Thanx for reply.but I mentioned that when we do shut no shut again link comes up.no dlci, no lmi problem: I am testing in lab setup two rouetrs connnected to frame-relay cloud Please do help anybody in this regard, why the link doesnot come at one instant why it requiers again shut and no shut, when i copy paste the config and when i give command by command then without gving shut and noshut the link comes up. Mark W. Odette II wrote: in show ip interface it shows as protocol down , physical link up. sh frame-relay pvs shows as inactive.no lmi are exchanged. Usually Protocol Down, Link Up indicates that you have mismatched encapsulation, LMI-Type, or even incorrect IP Addressing (wrong Subnet or incorrect Subnet Mask) between your end and the other end of the FR Network. If no LMI is exchanged, then the LMI-Type is incorrect between that Serial Interface and the Service Provider Frame Switch. If this is a Frame Relay LAB setup, double-check your Frame Relay Switch configuration. If this is a Production Setup, contact your ISP and verify your Frame Relay configuration parameters. (LMI-Type, DLCI, etc.) On the No Shut command, I'd use it last on each interface you configure. -Mark -Original Message- From: Monu Sekhon [mailto:[EMAIL PROTECTED]] Sent: Thursday, February 20, 2003 7:40 PM To: [EMAIL PROTECTED] Subject: Re: Frame-Relay issue [7:63446] Hi Larry/John, I forgot to mention no shut in the above confif while writing here, Its still there and connection does not come out See I mentioned that while giving command by command manually connection comes out. It seems to me that while the interface is down during that frame-relay LMIs think that interface is down and make the link down. I am rather confused.I dont know but this is happening. again writing config: -- interface Serial0 shut (if i give here no shut then link comes up at one go) encapsulation frame-relay frame-relay lmi-type cisco no shut exit interface Serial0/0.1 point-to-point no shutdown ip address 1.1.1.1 255.255.255.0 frame-relay interface-dlci 108 exit and also John try these in your router but at one go the interface will not come up as far i know .I agree with ur confguration and mine is also correct .Its said by Prisicilla and others that shutting a interface is good practise while configuring encap types.This i read in one of the previous Posts. so can u all reply what is the problem here in show ip interface it shows as protocol down , physical link up. sh frame-relay pvs shows as inactive.no lmi are exchanged. any help will be appreciated. - Larry Letterman wrote: enter the no shut command into your cut and paste script for the Int Ser0 and it will come up..all interfaces in a router are always defaulted to shutdown..In your case the Main interface needs to be no shut in order for the logical interface to work... -- Larry Letterman Network Engineer Cisco Systems Monu Sekhon wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... Hi All Hey I am facing a strange problem in frame-relay My config -- my initial config int serial 0 (nothing confgured initially) Then I cut paste this config and my link does not come up means Interface does not come up. interface Serial0 shut (if i give here no shut then link comes up at one go) encapsulation frame-relay frame-relay lmi-type cisco exit interface Serial0/0.1 point-to-point no shutdown ip address 1.1.1.1 255.255.255.0 frame-relay interface-dlci 108 exit I have to do shut and no shut on main interface why ? if the above commands i execute one by one then the link comes up. Is it a differnece between pasting the config at one go or what when i give command single by single. I enable debugging for frame-relay packets and it shows encap faiiled once only on the above sub interface.is anything frame-relay lmis has anything to do. I am very confused. Thanx in advance [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=63495t=63446 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Frame-Relay issue [7:63446]
There's obviously no good answer to why there are no problems bringing the link up/up when you type in the commands one by one but there are problems when you copy and paste them. Here are some suggestions, though: 1) You work for Cisco. Report it as a bug. 2) The copy and paste is corrupting a character, forgetting to do carriage return or something of that nature. Do all the commands end up the in the running config? 3) There's some sort of timing issue. To fix the problem: Don't do copy and paste that fast. :-) Priscilla Monu Sekhon wrote: Hi Mark, Thanx for reply.but I mentioned that when we do shut no shut again link comes up.no dlci, no lmi problem: I am testing in lab setup two rouetrs connnected to frame-relay cloud Please do help anybody in this regard, why the link doesnot come at one instant why it requiers again shut and no shut, when i copy paste the config and when i give command by command then without gving shut and noshut the link comes up. Mark W. Odette II wrote: in show ip interface it shows as protocol down , physical link up. sh frame-relay pvs shows as inactive.no lmi are exchanged. Usually Protocol Down, Link Up indicates that you have mismatched encapsulation, LMI-Type, or even incorrect IP Addressing (wrong Subnet or incorrect Subnet Mask) between your end and the other end of the FR Network. If no LMI is exchanged, then the LMI-Type is incorrect between that Serial Interface and the Service Provider Frame Switch. If this is a Frame Relay LAB setup, double-check your Frame Relay Switch configuration. If this is a Production Setup, contact your ISP and verify your Frame Relay configuration parameters. (LMI-Type, DLCI, etc.) On the No Shut command, I'd use it last on each interface you configure. -Mark -Original Message- From: Monu Sekhon [mailto:[EMAIL PROTECTED] Sent: Thursday, February 20, 2003 7:40 PM To: [EMAIL PROTECTED] Subject: Re: Frame-Relay issue [7:63446] Hi Larry/John, I forgot to mention no shut in the above confif while writing here, Its still there and connection does not come out See I mentioned that while giving command by command manually connection comes out. It seems to me that while the interface is down during that frame-relay LMIs think that interface is down and make the link down. I am rather confused.I dont know but this is happening. again writing config: -- interface Serial0 shut (if i give here no shut then link comes up at one go) encapsulation frame-relay frame-relay lmi-type cisco no shut exit interface Serial0/0.1 point-to-point no shutdown ip address 1.1.1.1 255.255.255.0 frame-relay interface-dlci 108 exit and also John try these in your router but at one go the interface will not come up as far i know .I agree with ur confguration and mine is also correct .Its said by Prisicilla and others that shutting a interface is good practise while configuring encap types.This i read in one of the previous Posts. so can u all reply what is the problem here in show ip interface it shows as protocol down , physical link up. sh frame-relay pvs shows as inactive.no lmi are exchanged. any help will be appreciated. - Larry Letterman wrote: enter the no shut command into your cut and paste script for the Int Ser0 and it will come up..all interfaces in a router are always defaulted to shutdown..In your case the Main interface needs to be no shut in order for the logical interface to work... -- Larry Letterman Network Engineer Cisco Systems Monu Sekhon wrote in message news:[EMAIL PROTECTED] Hi All Hey I am facing a strange problem in frame-relay My config -- my initial config int serial 0 (nothing confgured initially) Then I cut paste this config and my link does not come up means Interface does not come up. interface Serial0 shut (if i give here no shut then link comes up at one go) encapsulation frame-relay frame-relay lmi-type cisco exit interface Serial0/0.1 point-to-point no shutdown ip address 1.1.1.1 255.255.255.0 frame-relay interface-dlci 108 exit I have to do shut and no shut on main interface why ? if the above commands i execute one by one then the link comes up. Is it a differnece between pasting the config at one go or what when i give command single by single. I enable debugging for frame-relay packets and it shows encap faiiled once only on the above sub interface.is anything frame-relay lmis has anything to do. I am very confused. Thanx in advance [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=63523t
RE: Frame-Relay issue [7:63446]
I would check your settings such as the LMI type, Have you done any other fault finding yet ? Such as sh frame relay pvc ? Once you hit no shutdown, the interface becomes live in a way of speaking. Here is an example of one of my configs. interface Serial0/0 no ip address encapsulation frame-relay IETF ! interface Serial0/0.1AA point-to-point description Johns Config ip address x.x.x.x b.b.b.b no cdp enable frame-relay interface-dlci AA IETF I have replaced some values here with letters for security John ** visit http://www.solution6.com UK Customers - http://www.solution6.co.uk ** The Solution 6 Head Office and NSW Branch has moved premises. Please make sure you have updated your records with our new details. Level 14, 383 Kent Street, Sydney NSW 2000. General Phone: 61 2 9278 0666 General Fax: 61 2 9278 0555 ** This email message (and attachments) may contain information that is confidential to Solution 6. If you are not the intended recipient you cannot use, distribute or copy the message or attachments. In such a case, please notify the sender by return email immediately and erase all copies of the message and attachments. Opinions, conclusions and other information in this message and attachments that do not relate to the official business of Solution 6 are neither given nor endorsed by it. * Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=63449t=63446 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Frame-Relay issue [7:63446]
enter the no shut command into your cut and paste script for the Int Ser0 and it will come up..all interfaces in a router are always defaulted to shutdown..In your case the Main interface needs to be no shut in order for the logical interface to work... -- Larry Letterman Network Engineer Cisco Systems Monu Sekhon wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... Hi All Hey I am facing a strange problem in frame-relay My config -- my initial config int serial 0 (nothing confgured initially) Then I cut paste this config and my link does not come up means Interface does not come up. interface Serial0 shut (if i give here no shut then link comes up at one go) encapsulation frame-relay frame-relay lmi-type cisco exit interface Serial0/0.1 point-to-point no shutdown ip address 1.1.1.1 255.255.255.0 frame-relay interface-dlci 108 exit I have to do shut and no shut on main interface why ? if the above commands i execute one by one then the link comes up. Is it a differnece between pasting the config at one go or what when i give command single by single. I enable debugging for frame-relay packets and it shows encap faiiled once only on the above sub interface.is anything frame-relay lmis has anything to do. I am very confused. Thanx in advance [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=63454t=63446 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Frame-Relay issue [7:63446]
Hi Larry/John, I forgot to mention no shut in the above confif while writing here, Its still there and connection does not come out See I mentioned that while giving command by command manually connection comes out. It seems to me that while the interface is down during that frame-relay LMIs think that interface is down and make the link down. I am rather confused.I dont know but this is happening. again writing config: -- interface Serial0 shut (if i give here no shut then link comes up at one go) encapsulation frame-relay frame-relay lmi-type cisco no shut exit interface Serial0/0.1 point-to-point no shutdown ip address 1.1.1.1 255.255.255.0 frame-relay interface-dlci 108 exit and also John try these in your router but at one go the interface will not come up as far i know .I agree with ur confguration and mine is also correct .Its said by Prisicilla and others that shutting a interface is good practise while configuring encap types.This i read in one of the previous Posts. so can u all reply what is the problem here in show ip interface it shows as protocol down , physical link up. sh frame-relay pvs shows as inactive.no lmi are exchanged. any help will be appreciated. - Larry Letterman wrote: enter the no shut command into your cut and paste script for the Int Ser0 and it will come up..all interfaces in a router are always defaulted to shutdown..In your case the Main interface needs to be no shut in order for the logical interface to work... -- Larry Letterman Network Engineer Cisco Systems Monu Sekhon wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... Hi All Hey I am facing a strange problem in frame-relay My config -- my initial config int serial 0 (nothing confgured initially) Then I cut paste this config and my link does not come up means Interface does not come up. interface Serial0 shut (if i give here no shut then link comes up at one go) encapsulation frame-relay frame-relay lmi-type cisco exit interface Serial0/0.1 point-to-point no shutdown ip address 1.1.1.1 255.255.255.0 frame-relay interface-dlci 108 exit I have to do shut and no shut on main interface why ? if the above commands i execute one by one then the link comes up. Is it a differnece between pasting the config at one go or what when i give command single by single. I enable debugging for frame-relay packets and it shows encap faiiled once only on the above sub interface.is anything frame-relay lmis has anything to do. I am very confused. Thanx in advance [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=63459t=63446 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Frame-Relay issue [7:63446]
in show ip interface it shows as protocol down , physical link up. sh frame-relay pvs shows as inactive.no lmi are exchanged. Usually Protocol Down, Link Up indicates that you have mismatched encapsulation, LMI-Type, or even incorrect IP Addressing (wrong Subnet or incorrect Subnet Mask) between your end and the other end of the FR Network. If no LMI is exchanged, then the LMI-Type is incorrect between that Serial Interface and the Service Provider Frame Switch. If this is a Frame Relay LAB setup, double-check your Frame Relay Switch configuration. If this is a Production Setup, contact your ISP and verify your Frame Relay configuration parameters. (LMI-Type, DLCI, etc.) On the No Shut command, I'd use it last on each interface you configure. -Mark -Original Message- From: Monu Sekhon [mailto:[EMAIL PROTECTED]] Sent: Thursday, February 20, 2003 7:40 PM To: [EMAIL PROTECTED] Subject: Re: Frame-Relay issue [7:63446] Hi Larry/John, I forgot to mention no shut in the above confif while writing here, Its still there and connection does not come out See I mentioned that while giving command by command manually connection comes out. It seems to me that while the interface is down during that frame-relay LMIs think that interface is down and make the link down. I am rather confused.I dont know but this is happening. again writing config: -- interface Serial0 shut (if i give here no shut then link comes up at one go) encapsulation frame-relay frame-relay lmi-type cisco no shut exit interface Serial0/0.1 point-to-point no shutdown ip address 1.1.1.1 255.255.255.0 frame-relay interface-dlci 108 exit and also John try these in your router but at one go the interface will not come up as far i know .I agree with ur confguration and mine is also correct .Its said by Prisicilla and others that shutting a interface is good practise while configuring encap types.This i read in one of the previous Posts. so can u all reply what is the problem here in show ip interface it shows as protocol down , physical link up. sh frame-relay pvs shows as inactive.no lmi are exchanged. any help will be appreciated. - Larry Letterman wrote: enter the no shut command into your cut and paste script for the Int Ser0 and it will come up..all interfaces in a router are always defaulted to shutdown..In your case the Main interface needs to be no shut in order for the logical interface to work... -- Larry Letterman Network Engineer Cisco Systems Monu Sekhon wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... Hi All Hey I am facing a strange problem in frame-relay My config -- my initial config int serial 0 (nothing confgured initially) Then I cut paste this config and my link does not come up means Interface does not come up. interface Serial0 shut (if i give here no shut then link comes up at one go) encapsulation frame-relay frame-relay lmi-type cisco exit interface Serial0/0.1 point-to-point no shutdown ip address 1.1.1.1 255.255.255.0 frame-relay interface-dlci 108 exit I have to do shut and no shut on main interface why ? if the above commands i execute one by one then the link comes up. Is it a differnece between pasting the config at one go or what when i give command single by single. I enable debugging for frame-relay packets and it shows encap faiiled once only on the above sub interface.is anything frame-relay lmis has anything to do. I am very confused. Thanx in advance [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=63482t=63446 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
