Strange problem with Cisco 2501 routers
Hi Folks, I have a few Cisco 2501 routers all eith the same startup problem. On startup, the routers behave normal, but after the "Press RETURN to get started" message, the routers come up with errors about the ethernet and serial interfaces, restarts and then hang up completely. Thinking that the problem may be with the DRAM, Flash or software, I have replaced these with ones from other Cisco 2501 routers in good working condition, but the problem remained the same. The typical output from these routers is as shown at the end of this posting. Any good ideas will be appreciated. Thank you. System Bootstrap, Version (3.3), SOFTWARE Copyright (c) 1986-1993 by cisco Systems 2500 processor with 4096 Kbytes of main memory Unknown or ambiguous service arg - udp-small-servers Unknown or ambiguous service arg - tcp-small-servers Illegal IP keyword - classless Booting ie11170n from Flash address space F3: 3731220+95304+191716 at 0x360 Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) 3000 Software (IGS-I-L), Version 11.1(7), RELEASE SOFTWARE (fc2) Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Wed 23-Oct-96 20:37 by tej Image text-base: 0x0301FC14, data-base: 0x1000 cisco 2500 (68030) processor (revision A) with 4096K/2048K bytes of memory. Processor board ID 01091217, with hardware revision Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. 1 Ethernet/IEEE 802.3 interface. 2 Serial network interfaces. 32K bytes of non-volatile configuration memory. 4096K bytes of processor board System flash (Read ONLY) Press RETURN to get started! %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down %LINK-3-UPDOWN: Interface Ethernet0, changed state to up %LINK-3-UPDOWN: Interface Serial0, changed state to down %LINK-3-UPDOWN: Interface Serial1, changed state to down %SYS-5-CONFIG_I: Configured from memory by console %SYS-5-RESTART: System restarted -- Cisco Internetwork Operating System Software IOS (tm) 3000 Software (IGS-I-L), Version 11.1(7), RELEASE SOFTWARE (fc2) Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Wed 23-Oct-96 20:37 by tej %LINK-5-CHANGED: Interface Serial1, changed state to administratively down __ Do You Yahoo!? Yahoo! Auctions - Buy the things you want at great prices. http://auctions.yahoo.com/ _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Strange problem with Cisco 2501 routers
I would need to see a "show conf" output for your interfaces. Ole Ole Drews Jensen Systems Network Manager CCNA, MCSE, MCP+I RWR Enterprises, Inc. [EMAIL PROTECTED] http://www.CiscoKing.com NEED A JOB ??? http://www.oledrews.com/job -Original Message- From: Cisco Engineer [mailto:[EMAIL PROTECTED]] Sent: Wednesday, February 07, 2001 8:28 AM To: [EMAIL PROTECTED] Subject: Strange problem with Cisco 2501 routers Hi Folks, I have a few Cisco 2501 routers all eith the same startup problem. On startup, the routers behave normal, but after the "Press RETURN to get started" message, the routers come up with errors about the ethernet and serial interfaces, restarts and then hang up completely. Thinking that the problem may be with the DRAM, Flash or software, I have replaced these with ones from other Cisco 2501 routers in good working condition, but the problem remained the same. The typical output from these routers is as shown at the end of this posting. Any good ideas will be appreciated. Thank you. System Bootstrap, Version (3.3), SOFTWARE Copyright (c) 1986-1993 by cisco Systems 2500 processor with 4096 Kbytes of main memory Unknown or ambiguous service arg - udp-small-servers Unknown or ambiguous service arg - tcp-small-servers Illegal IP keyword - classless Booting ie11170n from Flash address space F3: 3731220+95304+191716 at 0x360 Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) 3000 Software (IGS-I-L), Version 11.1(7), RELEASE SOFTWARE (fc2) Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Wed 23-Oct-96 20:37 by tej Image text-base: 0x0301FC14, data-base: 0x1000 cisco 2500 (68030) processor (revision A) with 4096K/2048K bytes of memory. Processor board ID 01091217, with hardware revision Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. 1 Ethernet/IEEE 802.3 interface. 2 Serial network interfaces. 32K bytes of non-volatile configuration memory. 4096K bytes of processor board System flash (Read ONLY) Press RETURN to get started! %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down %LINK-3-UPDOWN: Interface Ethernet0, changed state to up %LINK-3-UPDOWN: Interface Serial0, changed state to down %LINK-3-UPDOWN: Interface Serial1, changed state to down %SYS-5-CONFIG_I: Configured from memory by console %SYS-5-RESTART: System restarted -- Cisco Internetwork Operating System Software IOS (tm) 3000 Software (IGS-I-L), Version 11.1(7), RELEASE SOFTWARE (fc2) Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Wed 23-Oct-96 20:37 by tej %LINK-5-CHANGED: Interface Serial1, changed state to administratively down __ Do You Yahoo!? Yahoo! Auctions - Buy the things you want at great prices. http://auctions.yahoo.com/ _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Strange problem with Cisco 2501 routers
The only startup errors evident in this output is this: Unknown or ambiguous service arg - udp-small-servers Unknown or ambiguous service arg - tcp-small-servers Illegal IP keyword - classless You're probably seeing this because you are running IOS 11.1(7), but your config is pasted in from a router running at least 11.2. 11.1(7) apparently doesn't understand these lines: service udp-small-servers service tcp-small-servers ip classless You can upgrade your IOS or remove those lines from your config. The status messages about the interfaces are not strange in any way. They look quite normal, assuming the ethernet port was connected to something but the serial ports were not. HTH, John Hi Folks, I have a few Cisco 2501 routers all eith the same startup problem. On startup, the routers behave normal, but after the "Press RETURN to get started" message, the routers come up with errors about the ethernet and serial interfaces, restarts and then hang up completely. Thinking that the problem may be with the DRAM, Flash or software, I have replaced these with ones from other Cisco 2501 routers in good working condition, but the problem remained the same. The typical output from these routers is as shown at the end of this posting. Any good ideas will be appreciated. Thank you. System Bootstrap, Version (3.3), SOFTWARE Copyright (c) 1986-1993 by cisco Systems 2500 processor with 4096 Kbytes of main memory Unknown or ambiguous service arg - udp-small-servers Unknown or ambiguous service arg - tcp-small-servers Illegal IP keyword - classless Booting ie11170n from Flash address space F3: 3731220+95304+191716 at 0x360 Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) 3000 Software (IGS-I-L), Version 11.1(7), RELEASE SOFTWARE (fc2) Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Wed 23-Oct-96 20:37 by tej Image text-base: 0x0301FC14, data-base: 0x1000 cisco 2500 (68030) processor (revision A) with 4096K/2048K bytes of memory. Processor board ID 01091217, with hardware revision Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. 1 Ethernet/IEEE 802.3 interface. 2 Serial network interfaces. 32K bytes of non-volatile configuration memory. 4096K bytes of processor board System flash (Read ONLY) Press RETURN to get started! %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down %LINK-3-UPDOWN: Interface Ethernet0, changed state to up %LINK-3-UPDOWN: Interface Serial0, changed state to down %LINK-3-UPDOWN: Interface Serial1, changed state to down %SYS-5-CONFIG_I: Configured from memory by console %SYS-5-RESTART: System restarted -- Cisco Internetwork Operating System Software IOS (tm) 3000 Software (IGS-I-L), Version 11.1(7), RELEASE SOFTWARE (fc2) Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Wed 23-Oct-96 20:37 by tej %LINK-5-CHANGED: Interface Serial1, changed state to administratively down __ Do You Yahoo!? Yahoo! Auctions - Buy the things you want at great prices. http://auctions.yahoo.com/ _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Find the best deals on the web at AltaVista Shopping! http://www.shopping.altavista.com _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Strange problem with Cisco 2501 routers
You're right, but I think he is talking about the UPDOWN messages. This could be due to a "shutdown" line in each interface, but it would help to see the configuration. Ole Ole Drews Jensen Systems Network Manager CCNA, MCSE, MCP+I RWR Enterprises, Inc. [EMAIL PROTECTED] http://www.CiscoKing.com NEED A JOB ??? http://www.oledrews.com/job -Original Message- From: John Neiberger [mailto:[EMAIL PROTECTED]] Sent: Wednesday, February 07, 2001 9:17 AM To: [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Subject: Re: Strange problem with Cisco 2501 routers The only startup errors evident in this output is this: Unknown or ambiguous service arg - udp-small-servers Unknown or ambiguous service arg - tcp-small-servers Illegal IP keyword - classless You're probably seeing this because you are running IOS 11.1(7), but your config is pasted in from a router running at least 11.2. 11.1(7) apparently doesn't understand these lines: service udp-small-servers service tcp-small-servers ip classless You can upgrade your IOS or remove those lines from your config. The status messages about the interfaces are not strange in any way. They look quite normal, assuming the ethernet port was connected to something but the serial ports were not. HTH, John Hi Folks, I have a few Cisco 2501 routers all eith the same startup problem. On startup, the routers behave normal, but after the "Press RETURN to get started" message, the routers come up with errors about the ethernet and serial interfaces, restarts and then hang up completely. Thinking that the problem may be with the DRAM, Flash or software, I have replaced these with ones from other Cisco 2501 routers in good working condition, but the problem remained the same. The typical output from these routers is as shown at the end of this posting. Any good ideas will be appreciated. Thank you. System Bootstrap, Version (3.3), SOFTWARE Copyright (c) 1986-1993 by cisco Systems 2500 processor with 4096 Kbytes of main memory Unknown or ambiguous service arg - udp-small-servers Unknown or ambiguous service arg - tcp-small-servers Illegal IP keyword - classless Booting ie11170n from Flash address space F3: 3731220+95304+191716 at 0x360 Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) 3000 Software (IGS-I-L), Version 11.1(7), RELEASE SOFTWARE (fc2) Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Wed 23-Oct-96 20:37 by tej Image text-base: 0x0301FC14, data-base: 0x1000 cisco 2500 (68030) processor (revision A) with 4096K/2048K bytes of memory. Processor board ID 01091217, with hardware revision Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. 1 Ethernet/IEEE 802.3 interface. 2 Serial network interfaces. 32K bytes of non-volatile configuration memory. 4096K bytes of processor board System flash (Read ONLY) Press RETURN to get started! %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down %LINK-3-UPDOWN: Interface Ethernet0, changed state to up %LINK-3-UPDOWN: Interface Serial0, changed state to down %LINK-3-UPDOWN: Interface Serial1, changed state to down %SYS-5-CONFIG_I: Configured from memory by console %SYS-5-RESTART: System restarted -- Cisco Internetwork Operating System Software IOS (tm) 3000 Software (IGS-I-L), Version 11.1(7), RELEASE SOFTWARE (fc2) Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Wed 23-Oct-96 20:37 by tej %LINK-5-CHANGED: Interface Serial1, changed state to administratively down __ Do You Yahoo!? Yahoo! Auctions - Buy the things you want at great prices. http://auctions.yahoo.com/ _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Find the best deals on the web at AltaVista Shopping! http://www.shopping.altavista.com _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations
RE: Strange problem with Cisco 2501 routers
Do you have a TFTP server on the segment maybe with a file net-conf? It could be pulling a bad configuration file from a tftp server. Also it might be trying to pull a IOS image from a TFTP server that is not there. It might have a boot system tftp command in the config. I assume you just got these and you are experiencing the problem. Try going into ROM mode and change the Configuration register to ignore the start up config file (confreg 0x142). reload the router and see what the config look like. I have a feeling it is looking for something off a TFTP server. If you want you can make a copy of the config and then do a write erase. Change back the Config Register to 0x2102 (Router#config-reg 0x2102). Reload the router and see if you get the same error. Hope this helps Drew -Original Message- From: Ole Drews Jensen [mailto:[EMAIL PROTECTED]] Sent: Wednesday, February 07, 2001 7:31 AM To: 'John Neiberger'; [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Subject: RE: Strange problem with Cisco 2501 routers You're right, but I think he is talking about the UPDOWN messages. This could be due to a "shutdown" line in each interface, but it would help to see the configuration. Ole Ole Drews Jensen Systems Network Manager CCNA, MCSE, MCP+I RWR Enterprises, Inc. [EMAIL PROTECTED] http://www.CiscoKing.com NEED A JOB ??? http://www.oledrews.com/job -Original Message- From: John Neiberger [mailto:[EMAIL PROTECTED]] Sent: Wednesday, February 07, 2001 9:17 AM To: [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Subject: Re: Strange problem with Cisco 2501 routers The only startup errors evident in this output is this: Unknown or ambiguous service arg - udp-small-servers Unknown or ambiguous service arg - tcp-small-servers Illegal IP keyword - classless You're probably seeing this because you are running IOS 11.1(7), but your config is pasted in from a router running at least 11.2. 11.1(7) apparently doesn't understand these lines: service udp-small-servers service tcp-small-servers ip classless You can upgrade your IOS or remove those lines from your config. The status messages about the interfaces are not strange in any way. They look quite normal, assuming the ethernet port was connected to something but the serial ports were not. HTH, John Hi Folks, I have a few Cisco 2501 routers all eith the same startup problem. On startup, the routers behave normal, but after the "Press RETURN to get started" message, the routers come up with errors about the ethernet and serial interfaces, restarts and then hang up completely. Thinking that the problem may be with the DRAM, Flash or software, I have replaced these with ones from other Cisco 2501 routers in good working condition, but the problem remained the same. The typical output from these routers is as shown at the end of this posting. Any good ideas will be appreciated. Thank you. System Bootstrap, Version (3.3), SOFTWARE Copyright (c) 1986-1993 by cisco Systems 2500 processor with 4096 Kbytes of main memory Unknown or ambiguous service arg - udp-small-servers Unknown or ambiguous service arg - tcp-small-servers Illegal IP keyword - classless Booting ie11170n from Flash address space F3: 3731220+95304+191716 at 0x360 Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) 3000 Software (IGS-I-L), Version 11.1(7), RELEASE SOFTWARE (fc2) Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Wed 23-Oct-96 20:37 by tej Image text-base: 0x0301FC14, data-base: 0x1000 cisco 2500 (68030) processor (revision A) with 4096K/2048K bytes of memory. Processor board ID 01091217, with hardware revision Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. 1 Ethernet/IEEE 802.3 interface. 2 Serial network interfaces. 32K bytes of non-volatile configuration memory. 4096K bytes of processor board System flash (Read ONLY) Press RETURN to get started! %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down %LINK-3-UPDOWN: Interface Ethernet0, changed state to up %LINK-3-UPDOWN: Interface Serial0, changed state to down %LINK-3-UPDOW
RE: Strange problem with Cisco 2501 routers
The ROM version of 3.3 catches my eye. Might be good to update those. Call the TAC. They will provide them for shipping cost. -Original Message- From: Cisco Engineer [mailto:[EMAIL PROTECTED]] Sent: Wednesday, February 07, 2001 8:28 AM To: [EMAIL PROTECTED] Subject: Strange problem with Cisco 2501 routers Hi Folks, I have a few Cisco 2501 routers all eith the same startup problem. On startup, the routers behave normal, but after the "Press RETURN to get started" message, the routers come up with errors about the ethernet and serial interfaces, restarts and then hang up completely. Thinking that the problem may be with the DRAM, Flash or software, I have replaced these with ones from other Cisco 2501 routers in good working condition, but the problem remained the same. The typical output from these routers is as shown at the end of this posting. Any good ideas will be appreciated. Thank you. System Bootstrap, Version (3.3), SOFTWARE Copyright (c) 1986-1993 by cisco Systems 2500 processor with 4096 Kbytes of main memory Unknown or ambiguous service arg - udp-small-servers Unknown or ambiguous service arg - tcp-small-servers Illegal IP keyword - classless Booting ie11170n from Flash address space F3: 3731220+95304+191716 at 0x360 Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) 3000 Software (IGS-I-L), Version 11.1(7), RELEASE SOFTWARE (fc2) Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Wed 23-Oct-96 20:37 by tej Image text-base: 0x0301FC14, data-base: 0x1000 cisco 2500 (68030) processor (revision A) with 4096K/2048K bytes of memory. Processor board ID 01091217, with hardware revision Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. 1 Ethernet/IEEE 802.3 interface. 2 Serial network interfaces. 32K bytes of non-volatile configuration memory. 4096K bytes of processor board System flash (Read ONLY) Press RETURN to get started! %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down %LINK-3-UPDOWN: Interface Ethernet0, changed state to up %LINK-3-UPDOWN: Interface Serial0, changed state to down %LINK-3-UPDOWN: Interface Serial1, changed state to down %SYS-5-CONFIG_I: Configured from memory by console %SYS-5-RESTART: System restarted -- Cisco Internetwork Operating System Software IOS (tm) 3000 Software (IGS-I-L), Version 11.1(7), RELEASE SOFTWARE (fc2) Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Wed 23-Oct-96 20:37 by tej %LINK-5-CHANGED: Interface Serial1, changed state to administratively down __ Do You Yahoo!? Yahoo! Auctions - Buy the things you want at great prices. http://auctions.yahoo.com/ _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Strange problem with Cisco 2501 routers
So... if you hit enter after all these messages have completed, what happens? JMcL -- Forwarded by Jenny Mcleod/NSO/CSDA on 08/02/2001 08:56 am --- Cisco Engineer [EMAIL PROTECTED]@groupstudy.com on 08/02/2001 01:27:56 am Please respond to Cisco Engineer [EMAIL PROTECTED] Sent by: [EMAIL PROTECTED] To: [EMAIL PROTECTED] cc: Subject: Strange problem with Cisco 2501 routers Hi Folks, I have a few Cisco 2501 routers all eith the same startup problem. On startup, the routers behave normal, but after the "Press RETURN to get started" message, the routers come up with errors about the ethernet and serial interfaces, restarts and then hang up completely. Thinking that the problem may be with the DRAM, Flash or software, I have replaced these with ones from other Cisco 2501 routers in good working condition, but the problem remained the same. The typical output from these routers is as shown at the end of this posting. Any good ideas will be appreciated. Thank you. System Bootstrap, Version (3.3), SOFTWARE Copyright (c) 1986-1993 by cisco Systems 2500 processor with 4096 Kbytes of main memory Unknown or ambiguous service arg - udp-small-servers Unknown or ambiguous service arg - tcp-small-servers Illegal IP keyword - classless Booting ie11170n from Flash address space F3: 3731220+95304+191716 at 0x360 Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) 3000 Software (IGS-I-L), Version 11.1(7), RELEASE SOFTWARE (fc2) Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Wed 23-Oct-96 20:37 by tej Image text-base: 0x0301FC14, data-base: 0x1000 cisco 2500 (68030) processor (revision A) with 4096K/2048K bytes of memory. Processor board ID 01091217, with hardware revision Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. 1 Ethernet/IEEE 802.3 interface. 2 Serial network interfaces. 32K bytes of non-volatile configuration memory. 4096K bytes of processor board System flash (Read ONLY) Press RETURN to get started! %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down %LINK-3-UPDOWN: Interface Ethernet0, changed state to up %LINK-3-UPDOWN: Interface Serial0, changed state to down %LINK-3-UPDOWN: Interface Serial1, changed state to down %SYS-5-CONFIG_I: Configured from memory by console %SYS-5-RESTART: System restarted -- Cisco Internetwork Operating System Software IOS (tm) 3000 Software (IGS-I-L), Version 11.1(7), RELEASE SOFTWARE (fc2) Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Wed 23-Oct-96 20:37 by tej %LINK-5-CHANGED: Interface Serial1, changed state to administratively down __ Do You Yahoo!? Yahoo! Auctions - Buy the things you want at great prices. http://auctions.yahoo.com/ _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
