Re: frame relay config [7:61757]
Hi Julian yes u can do that by using ip unnumbered and using subinterfaces point to pint I cant get u properly from ur question what u mean but see U can have many sub interfaces and all of them can use ip unnumbered If anybody other will comenst lets wait for answers ,and if possible please mail ur question in little detail Julian P wrote: Hi guys I am wandering if it is possible to configure my cisco 2610 for seperate frame relay point to point subinterfaces with the ip terminating on the 2610,and have the 2610 frame switch some other dlci`s and terminate the ip on another frame relay device at the same time. Any advice is appreciated Thanks Julian Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=61759t=61757 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: frame relay config [7:61757]
Hi I want to configure my 2610 for frame relay into my telco. Then clients from all over will connect with frame relay through the telco into my 2610. Now i need to have 2 pvc`s per client.One will terminate on my 2610 and the other pvc needs to be switched through my 2610 and terminated on another router.The clients routers will not be cisco though. I will obviously have to use sub interfaces for the different clients. I am just unsure how i will terminate the 1 pvc on my 2610 and at the same time frame switch the other pvc to another router Thanks Julian P wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... Hi guys I am wandering if it is possible to configure my cisco 2610 for seperate frame relay point to point subinterfaces with the ip terminating on the 2610,and have the 2610 frame switch some other dlci`s and terminate the ip on another frame relay device at the same time. Any advice is appreciated Thanks Julian Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=61761t=61757 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: frame relay config [7:61757]
From what i can find, you will need to configure the interface as an NNI, and then you frame-relay switch between 2 pvc you have on the router. the problem is that subinterfaces are not supported by an NNI interface. it can only be implemented on the main interface so u will need 2 serial interfaces for your 2 pvc that you will configure independently Frame-relay switching int se 0 encapsulation frame-relay frame-relay intf-type nni frame-relay interface-dlci 101 frame-relay route 101 interface serial 2 201 int se 1 encapsulation frame-relay ip address x.x.x.x frame-relay lmi-type ansi frame-relay interface-dlci 301 int se 2 encapsulation frame-relay ietf frame-relay interface-dlci 201 frame-relay lmi-type ansi frame-relay intf-type nni frame-relay route 201 interface serial 0 101 I should tell u that i have not tried this, i don't really have the time, but it might just work, you can achive the same thing, but differently with the need to do frame switching by using simple a policy based routing, which are quit easy to configure. hope the above helps regards Julian P a icrit dans le message de news: [EMAIL PROTECTED] Hi I want to configure my 2610 for frame relay into my telco. Then clients from all over will connect with frame relay through the telco into my 2610. Now i need to have 2 pvc`s per client.One will terminate on my 2610 and the other pvc needs to be switched through my 2610 and terminated on another router.The clients routers will not be cisco though. I will obviously have to use sub interfaces for the different clients. I am just unsure how i will terminate the 1 pvc on my 2610 and at the same time frame switch the other pvc to another router Thanks Julian P wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... Hi guys I am wandering if it is possible to configure my cisco 2610 for seperate frame relay point to point subinterfaces with the ip terminating on the 2610,and have the 2610 frame switch some other dlci`s and terminate the ip on another frame relay device at the same time. Any advice is appreciated Thanks Julian Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=61763t=61757 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: frame relay config [7:61757]
actually come to think about it, u don't have the conditions for NNI switching, u can't even do Hybrid switching, if the PVC through witch u wana switch is DTE, i see only the option of frame switching over an ip tunnel, but then again u have to have an ip segment available: as far as configuration goes it will be easy, check it out: u might be able to do this int se 0 ip address x.x.x.x encapsulation frame-relay frame-relay route 101 interface tunnel 1 201 int tunnel1 ip address x.x.x.x tunnel source x.x.x.x tunnel destination x.x.x.x the tunnel must be configured at the other end not all versions support switching to a tunnel, u will need to look it up oh yeah here is a link that some info about the switching ways that cisco supports: http://www.cisco.com/en/US/products/sw/iosswrel/ps1818/products_configuratio n_guide_chapter09186a00800878c7.html hope the above helps regards Juntao a icrit dans le message de news: [EMAIL PROTECTED] From what i can find, you will need to configure the interface as an NNI, and then you frame-relay switch between 2 pvc you have on the router. the problem is that subinterfaces are not supported by an NNI interface. it can only be implemented on the main interface so u will need 2 serial interfaces for your 2 pvc that you will configure independently Frame-relay switching int se 0 encapsulation frame-relay frame-relay intf-type nni frame-relay interface-dlci 101 frame-relay route 101 interface serial 2 201 int se 1 encapsulation frame-relay ip address x.x.x.x frame-relay lmi-type ansi frame-relay interface-dlci 301 int se 2 encapsulation frame-relay ietf frame-relay interface-dlci 201 frame-relay lmi-type ansi frame-relay intf-type nni frame-relay route 201 interface serial 0 101 I should tell u that i have not tried this, i don't really have the time, but it might just work, you can achive the same thing, but differently with the need to do frame switching by using simple a policy based routing, which are quit easy to configure. hope the above helps regards Julian P a icrit dans le message de news: [EMAIL PROTECTED] Hi I want to configure my 2610 for frame relay into my telco. Then clients from all over will connect with frame relay through the telco into my 2610. Now i need to have 2 pvc`s per client.One will terminate on my 2610 and the other pvc needs to be switched through my 2610 and terminated on another router.The clients routers will not be cisco though. I will obviously have to use sub interfaces for the different clients. I am just unsure how i will terminate the 1 pvc on my 2610 and at the same time frame switch the other pvc to another router Thanks Julian P wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... Hi guys I am wandering if it is possible to configure my cisco 2610 for seperate frame relay point to point subinterfaces with the ip terminating on the 2610,and have the 2610 frame switch some other dlci`s and terminate the ip on another frame relay device at the same time. Any advice is appreciated Thanks Julian Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=61765t=61757 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
frame relay config [7:61757]
Hi guys I am wandering if it is possible to configure my cisco 2610 for seperate frame relay point to point subinterfaces with the ip terminating on the 2610,and have the 2610 frame switch some other dlci`s and terminate the ip on another frame relay device at the same time. Any advice is appreciated Thanks Julian Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=61757t=61757 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
