Re: [Dx4win] JT65A

2016-08-12 Thread Dan Violette 
Easier to do in person.  Basic ideas:  Run in CW part of band first and get 
signal on the screen.  Should be blue/gray background with yellow signal 
(something like that, going by memory don't do too often).  Makes sure wide 
filter and there is a slider for shooting for 0 when no signal (and + numbers 
when signal).  When you see a signal, go to 14.076 and see if you find some 
JT65 there.  Make sure either digital mode or USB depending on what radio 
recommends.  If you hear something, it should decode at the end of the minute 
(46 seconds after).  Do that a bit until you are comfortable receiving.  Then 
TX is a combination of speaker output from the PC and radio mic gain along with 
PTT.  More difficult but get the RX first.

This all assumes you have the audio lines from the PC to the radio correct.  
May need to find a local friend who has done it.

Dan KI6X

-Original Message-
From: DX4WIN [mailto:dx4win-boun...@mailman.qth.net] On Behalf Of Courtney Judd
Sent: Thursday, August 11, 2016 3:03 PM
To: Joe Subich, W4TV <li...@subich.com>
Cc: ACG <cont...@alabamacontestgroup.org>; SECC <s...@contesting.com>; 
Dx4win@mailman.qth.net
Subject: Re: [Dx4win] JT65A

ok, I use a 2000D hooked to my computer via a microKeyer 2 by microHAM. 
I downloaded JT65-hf and it seemed to be much simpler. I have com port 3 for 
keying and rig control/freq etc selected as it is that way in the microHAM 
router. BUT, it will key but no audio received or sent and no freq showing. I 
have tried all combos of listed devices and no luck. 
Somehow I knew that this was not going to be easy!! lol any help/ideas? 
thanks Cort K4WI

> Joe Subich, W4TV <mailto:li...@subich.com> Thursday, August 11, 2016 
> 10:32 AM
>
> On 8/11/2016 10:40 AM, Björn Ekelund wrote:
> > If you use any of Microham's USB enabled units (CW keyers, TNC, rig
> > controllers...) this functionality is built in.
>
> Only microHAM "Keyer" series interfaces (microkeyer, microkeyer II, 
> digikeyer, digikeyer II, CW Keyer or MK2R+).  USB Interface II and USB 
> Interface III do not provide the CAT/2nd CAT capability as they have 
> no internal microprocessor.
>
> 73,
>
>... Joe, W4TV
>
>
>
> __
> DX4WIN mailing list
> Home: http://mailman.qth.net/mailman/listinfo/dx4win
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:DX4WIN@mailman.qth.net
>
> This list hosted by: http://www.qsl.net Please help support this email 
> list: http://www.qsl.net/donate.html
__
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:DX4WIN@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:DX4WIN@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Dx4win] JT65A

2016-08-11 Thread Courtney Judd 
ok, I use a 2000D hooked to my computer via a microKeyer 2 by microHAM. 
I downloaded JT65-hf and it seemed to be much simpler. I have com port 3 
for keying and rig control/freq etc selected as it is that way in the 
microHAM router. BUT, it will key but no audio received or sent and no 
freq showing. I have tried all combos of listed devices and no luck. 
Somehow I knew that this was not going to be easy!! lol any help/ideas? 
thanks Cort K4WI



Joe Subich, W4TV 
Thursday, August 11, 2016 10:32 AM

On 8/11/2016 10:40 AM, Björn Ekelund wrote:
> If you use any of Microham's USB enabled units (CW keyers, TNC, rig
> controllers...) this functionality is built in.

Only microHAM "Keyer" series interfaces (microkeyer, microkeyer II,
digikeyer, digikeyer II, CW Keyer or MK2R+).  USB Interface II and
USB Interface III do not provide the CAT/2nd CAT capability as they
have no internal microprocessor.

73,

   ... Joe, W4TV



__
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:DX4WIN@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:DX4WIN@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Dx4win] JT65A

2016-08-11 Thread Joe Subich, W4TV 


On 8/11/2016 10:40 AM, Björn Ekelund wrote:
> If you use any of Microham's USB enabled units (CW keyers, TNC, rig
> controllers...) this functionality is built in.

Only microHAM "Keyer" series interfaces (microkeyer, microkeyer II,
digikeyer, digikeyer II, CW Keyer or MK2R+).  USB Interface II and
USB Interface III do not provide the CAT/2nd CAT capability as they
have no internal microprocessor.

73,

   ... Joe, W4TV


On 8/11/2016 10:40 AM, Björn Ekelund wrote:

If you use any of Microham's USB enabled units (CW keyers, TNC, rig
controllers...) this functionality is built in.
http://www.microham.com/

You can have two virtual serial ports (e.g. COM1, COM2) in your PC/Mac
with a single CAT interface.
Running DX4Win and e.g. fldigi or even HRD in parallel works fine.

Björn SM7IUN

2016-08-11 1:43 GMT+02:00 John, K9EL <k...@comcast.net>:

If you download and install VSPE from Eterlogic, you can share one Com Port
with two different pieces of software, thus negating the need to turn off
radio control of DX4Win when using other software.   I use VSPE for DX4Win
and Radio Control software on the same single com port.

73,
John K9EL

-Original Message-
From: DX4WIN [mailto:dx4win-boun...@mailman.qth.net] On Behalf Of N4QS, Dave
Perry
Sent: Wednesday, August 10, 2016 5:40 PM
To: 'Courtney Judd' <k...@k4wi.net>; 'ACG' <cont...@alabamacontestgroup.org>
Cc: 'SECC' <s...@contesting.com>; Dx4win@mailman.qth.net
Subject: Re: [Dx4win] JT65A

Cort,

I use WSJT-X for JT65.  It is also available as a free download.  I setup
both WSJT-X and DX4WIN to run off of the same com port.  But I do not run
them at the same time.  When I want to work JT65, I click on Radio in DX4WIN
and click on Stop Radio, but I keep DX4WIN open.  This disconnects DX4WIN
from the radio and opens up the com port.

I then open WSJT-X and it automatically connects to the radio.  When I am
finished making a JT65 contact, the QSO is saved to the wsjt.log file.  I
then import the log file into DX4WIN.  Just go to File, Import/Export, make
sure ADIF is selected at the top, click on Import, go find the WSJT file in
your directory, double click on it, then when the window for Options for
Duplicates pops up, select Ignore Duplicate QSO.  This will ensure that you
only import any new JT65 QSOs into your DX4WIN log.

Since the signal reports from WSJT-X incorrectly go into the Notes for this
Call field, I then cut and paste to move the signal report information from
that field to the Notes for this QSO field.

When I am done working JT65, I close WSJT-X -- which frees up the com port.
I then click on Radio in DX4WIN and Start Radio to connect the radio back to
DX4WIN.  Again, not elegant but effective.  BTW, it is fun to work weak
signal JT65 on 6m as well as the other HF bands.  So you should give it a
try.

It would be great if Paul would someday start enhancing DX4WIN again.  I am
sure many of us would like to see an automatic interface between WSJT-X and
DX4WIN like there is for MMTTY.  We also need DX4WIN to support JT9 as a
mode.  I might also add that an automatic interface for Fldigi would be
great for the many other digital modes currently available.  But Paul has
been strangely inactive and incommunicado for five or six years now.

For the time being, this is a workaround that is cumbersome but pretty
foolproof.  Good luck.

73,

Dave, N4QS


-Original Message-
From: DX4WIN [mailto:dx4win-boun...@mailman.qth.net] On Behalf Of Courtney
Judd
Sent: Wednesday, August 10, 2016 3:14 PM
To: ACG
Cc: SECC; Dx4win@mailman.qth.net
Subject: [Dx4win] JT65A

well, I have been noticing that a lot of good dx is being spotted on
jt65 up around 50276 or so. Don't know anything about this but thought maybe
it might be something worth while to look into. So, I down loaded WSJT and
have it installed but looks to be very confusing to be sure. So any help on
getting me started would be appreciated. I also down loaded the instructions
and I can tell this is going to take some time and effort to get it all
playing correctly. I use DX4WIN for my general logging so maybe I would have
to have both programs open at the same time? Thanks, Cort K4WI
__
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:DX4WIN@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:DX4WIN@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Hel

Re: [Dx4win] JT65A

2016-08-11 Thread Björn Ekelund 
If you use any of Microham's USB enabled units (CW keyers, TNC, rig
controllers...) this functionality is built in.
http://www.microham.com/

You can have two virtual serial ports (e.g. COM1, COM2) in your PC/Mac
with a single CAT interface.
Running DX4Win and e.g. fldigi or even HRD in parallel works fine.

Björn SM7IUN

2016-08-11 1:43 GMT+02:00 John, K9EL <k...@comcast.net>:
> If you download and install VSPE from Eterlogic, you can share one Com Port
> with two different pieces of software, thus negating the need to turn off
> radio control of DX4Win when using other software.   I use VSPE for DX4Win
> and Radio Control software on the same single com port.
>
> 73,
> John K9EL
>
> -Original Message-
> From: DX4WIN [mailto:dx4win-boun...@mailman.qth.net] On Behalf Of N4QS, Dave
> Perry
> Sent: Wednesday, August 10, 2016 5:40 PM
> To: 'Courtney Judd' <k...@k4wi.net>; 'ACG' <cont...@alabamacontestgroup.org>
> Cc: 'SECC' <s...@contesting.com>; Dx4win@mailman.qth.net
> Subject: Re: [Dx4win] JT65A
>
> Cort,
>
> I use WSJT-X for JT65.  It is also available as a free download.  I setup
> both WSJT-X and DX4WIN to run off of the same com port.  But I do not run
> them at the same time.  When I want to work JT65, I click on Radio in DX4WIN
> and click on Stop Radio, but I keep DX4WIN open.  This disconnects DX4WIN
> from the radio and opens up the com port.
>
> I then open WSJT-X and it automatically connects to the radio.  When I am
> finished making a JT65 contact, the QSO is saved to the wsjt.log file.  I
> then import the log file into DX4WIN.  Just go to File, Import/Export, make
> sure ADIF is selected at the top, click on Import, go find the WSJT file in
> your directory, double click on it, then when the window for Options for
> Duplicates pops up, select Ignore Duplicate QSO.  This will ensure that you
> only import any new JT65 QSOs into your DX4WIN log.
>
> Since the signal reports from WSJT-X incorrectly go into the Notes for this
> Call field, I then cut and paste to move the signal report information from
> that field to the Notes for this QSO field.
>
> When I am done working JT65, I close WSJT-X -- which frees up the com port.
> I then click on Radio in DX4WIN and Start Radio to connect the radio back to
> DX4WIN.  Again, not elegant but effective.  BTW, it is fun to work weak
> signal JT65 on 6m as well as the other HF bands.  So you should give it a
> try.
>
> It would be great if Paul would someday start enhancing DX4WIN again.  I am
> sure many of us would like to see an automatic interface between WSJT-X and
> DX4WIN like there is for MMTTY.  We also need DX4WIN to support JT9 as a
> mode.  I might also add that an automatic interface for Fldigi would be
> great for the many other digital modes currently available.  But Paul has
> been strangely inactive and incommunicado for five or six years now.
>
> For the time being, this is a workaround that is cumbersome but pretty
> foolproof.  Good luck.
>
> 73,
>
> Dave, N4QS
>
>
> -Original Message-
> From: DX4WIN [mailto:dx4win-boun...@mailman.qth.net] On Behalf Of Courtney
> Judd
> Sent: Wednesday, August 10, 2016 3:14 PM
> To: ACG
> Cc: SECC; Dx4win@mailman.qth.net
> Subject: [Dx4win] JT65A
>
> well, I have been noticing that a lot of good dx is being spotted on
> jt65 up around 50276 or so. Don't know anything about this but thought maybe
> it might be something worth while to look into. So, I down loaded WSJT and
> have it installed but looks to be very confusing to be sure. So any help on
> getting me started would be appreciated. I also down loaded the instructions
> and I can tell this is going to take some time and effort to get it all
> playing correctly. I use DX4WIN for my general logging so maybe I would have
> to have both programs open at the same time? Thanks, Cort K4WI
> __
> DX4WIN mailing list
> Home: http://mailman.qth.net/mailman/listinfo/dx4win
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:DX4WIN@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
> __
> DX4WIN mailing list
> Home: http://mailman.qth.net/mailman/listinfo/dx4win
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:DX4WIN@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
> __
> DX4WIN mailing list
> Home: http://mailman.qth.net/mailman/listinfo/dx4win
> Help: http://mailman.qth.net

Re: [Dx4win] JT65A

2016-08-10 Thread John, K9EL 
If you download and install VSPE from Eterlogic, you can share one Com Port
with two different pieces of software, thus negating the need to turn off
radio control of DX4Win when using other software.   I use VSPE for DX4Win
and Radio Control software on the same single com port.

73,
John K9EL

-Original Message-
From: DX4WIN [mailto:dx4win-boun...@mailman.qth.net] On Behalf Of N4QS, Dave
Perry
Sent: Wednesday, August 10, 2016 5:40 PM
To: 'Courtney Judd' <k...@k4wi.net>; 'ACG' <cont...@alabamacontestgroup.org>
Cc: 'SECC' <s...@contesting.com>; Dx4win@mailman.qth.net
Subject: Re: [Dx4win] JT65A

Cort,

I use WSJT-X for JT65.  It is also available as a free download.  I setup
both WSJT-X and DX4WIN to run off of the same com port.  But I do not run
them at the same time.  When I want to work JT65, I click on Radio in DX4WIN
and click on Stop Radio, but I keep DX4WIN open.  This disconnects DX4WIN
from the radio and opens up the com port.

I then open WSJT-X and it automatically connects to the radio.  When I am
finished making a JT65 contact, the QSO is saved to the wsjt.log file.  I
then import the log file into DX4WIN.  Just go to File, Import/Export, make
sure ADIF is selected at the top, click on Import, go find the WSJT file in
your directory, double click on it, then when the window for Options for
Duplicates pops up, select Ignore Duplicate QSO.  This will ensure that you
only import any new JT65 QSOs into your DX4WIN log.

Since the signal reports from WSJT-X incorrectly go into the Notes for this
Call field, I then cut and paste to move the signal report information from
that field to the Notes for this QSO field.

When I am done working JT65, I close WSJT-X -- which frees up the com port.
I then click on Radio in DX4WIN and Start Radio to connect the radio back to
DX4WIN.  Again, not elegant but effective.  BTW, it is fun to work weak
signal JT65 on 6m as well as the other HF bands.  So you should give it a
try.

It would be great if Paul would someday start enhancing DX4WIN again.  I am
sure many of us would like to see an automatic interface between WSJT-X and
DX4WIN like there is for MMTTY.  We also need DX4WIN to support JT9 as a
mode.  I might also add that an automatic interface for Fldigi would be
great for the many other digital modes currently available.  But Paul has
been strangely inactive and incommunicado for five or six years now.

For the time being, this is a workaround that is cumbersome but pretty
foolproof.  Good luck.

73,

Dave, N4QS


-Original Message-
From: DX4WIN [mailto:dx4win-boun...@mailman.qth.net] On Behalf Of Courtney
Judd
Sent: Wednesday, August 10, 2016 3:14 PM
To: ACG
Cc: SECC; Dx4win@mailman.qth.net
Subject: [Dx4win] JT65A

well, I have been noticing that a lot of good dx is being spotted on
jt65 up around 50276 or so. Don't know anything about this but thought maybe
it might be something worth while to look into. So, I down loaded WSJT and
have it installed but looks to be very confusing to be sure. So any help on
getting me started would be appreciated. I also down loaded the instructions
and I can tell this is going to take some time and effort to get it all
playing correctly. I use DX4WIN for my general logging so maybe I would have
to have both programs open at the same time? Thanks, Cort K4WI
__
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:DX4WIN@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:DX4WIN@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:DX4WIN@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Dx4win] JT65A

2016-08-10 Thread N4QS, Dave Perry 
Cort,

I use WSJT-X for JT65.  It is also available as a free download.  I setup
both WSJT-X and DX4WIN to run off of the same com port.  But I do not run
them at the same time.  When I want to work JT65, I click on Radio in DX4WIN
and click on Stop Radio, but I keep DX4WIN open.  This disconnects DX4WIN
from the radio and opens up the com port.

I then open WSJT-X and it automatically connects to the radio.  When I am
finished making a JT65 contact, the QSO is saved to the wsjt.log file.  I
then import the log file into DX4WIN.  Just go to File, Import/Export, make
sure ADIF is selected at the top, click on Import, go find the WSJT file in
your directory, double click on it, then when the window for Options for
Duplicates pops up, select Ignore Duplicate QSO.  This will ensure that you
only import any new JT65 QSOs into your DX4WIN log.

Since the signal reports from WSJT-X incorrectly go into the Notes for this
Call field, I then cut and paste to move the signal report information from
that field to the Notes for this QSO field.

When I am done working JT65, I close WSJT-X -- which frees up the com port.
I then click on Radio in DX4WIN and Start Radio to connect the radio back to
DX4WIN.  Again, not elegant but effective.  BTW, it is fun to work weak
signal JT65 on 6m as well as the other HF bands.  So you should give it a
try.

It would be great if Paul would someday start enhancing DX4WIN again.  I am
sure many of us would like to see an automatic interface between WSJT-X and
DX4WIN like there is for MMTTY.  We also need DX4WIN to support JT9 as a
mode.  I might also add that an automatic interface for Fldigi would be
great for the many other digital modes currently available.  But Paul has
been strangely inactive and incommunicado for five or six years now.

For the time being, this is a workaround that is cumbersome but pretty
foolproof.  Good luck.

73,

Dave, N4QS


-Original Message-
From: DX4WIN [mailto:dx4win-boun...@mailman.qth.net] On Behalf Of Courtney
Judd
Sent: Wednesday, August 10, 2016 3:14 PM
To: ACG
Cc: SECC; Dx4win@mailman.qth.net
Subject: [Dx4win] JT65A

well, I have been noticing that a lot of good dx is being spotted on
jt65 up around 50276 or so. Don't know anything about this but thought maybe
it might be something worth while to look into. So, I down loaded WSJT and
have it installed but looks to be very confusing to be sure. So any help on
getting me started would be appreciated. I also down loaded the instructions
and I can tell this is going to take some time and effort to get it all
playing correctly. I use DX4WIN for my general logging so maybe I would have
to have both programs open at the same time? Thanks, Cort K4WI
__
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:DX4WIN@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:DX4WIN@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Dx4win] JT65A

2016-08-10 Thread Courtney Judd 
well, I have been noticing that a lot of good dx is being spotted on 
jt65 up around 50276 or so. Don't know anything about this but thought 
maybe it might be something worth while to look into. So, I down loaded 
WSJT and have it installed but looks to be very confusing to be sure. So 
any help on getting me started would be appreciated. I also down loaded 
the instructions and I can tell this is going to take some time and 
effort to get it all playing correctly. I use DX4WIN for my general 
logging so maybe I would have to have both programs open at the same 
time? Thanks, Cort K4WI

__
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:DX4WIN@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Dx4win] JT65A signal reports and DX4WIN

2011-12-26 Thread David M. Monfried 
For you JT65A users, how are you entering/handling signal reports (sent and
received) in DX4WIN for this mode? Using the latest version of DX4WIN,
entering the actual signal reports triggers the error message, value in
range to expected (sic).

 

Thanks.

 

Dave, W2PK

__
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:DX4WIN@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Dx4win] JT65A signal reports and DX4WIN

2011-12-26 Thread Art - W6KY 

I just let DX4WIN enter 59 and 599 for everything. I only note 'actual'
signal reports at the time of the QSO because an hour later they
are meaningless...
If you use the program JT65-HF it logs in an Excel file (jt65hf-log) file 
sent and received signal reports in dB. This you can then sort every
which way...
Of course JT65-HF also logs all contacts in an ADIF file which I
import into DX4WIN...
Fun stuff... 73, Art  W6KY
www.w6ky.com



From: David M. Monfried dmonfr...@comcast.net
To: DX4WIN@mailman.qth.net
Sent: Mon, December 26, 2011 5:39:59 PM
Subject: [Dx4win] JT65A signal reports and DX4WIN

For you JT65A users, how are you entering/handling signal reports (sent and
received) in DX4WIN for this mode? Using the latest version of DX4WIN,
entering the actual signal reports triggers the error message, value in
range to expected (sic).



Thanks.



Dave, W2PK

__
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:DX4WIN@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:DX4WIN@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Dx4win] JT65A LoTW

2011-01-27 Thread LU5FF - Javier 
Reply Forward
While I was able to export the contacts ..
thank you all.

javi LU5FF


Hello Javi,

The TrustedQSL program should include JT65 as a mode.

First thing to do is check your Adif file. Specifically look at the number 
of characters listed for mode. mode:4JT65 The number must read 4 for the 
four alpha-numeric information such as JT65. If you are using JT65A, the 
mode number should be 5 (five).

　

If the Adif file appears to be OK, please follow the instructions listed 
below to add JT65 to your TQSL program.

Open TQSL program.

Click FILE

Click Preferences

Click Adif Modes

Click ADD

In the Adif Mode box type JT65

In the Resulting TQSL mode highlight DATA

Click OK

Click OK

　

This should give add JT65 to your list.  (You can add JT65A as well.)

　

Thank you.

73,


Kathy AllisonKA1RWY
LoTW Specialist


ARRL - The national association for Amateur Radio
225 Main St
Newington CT 06111
Telephone:  860-594-0295


-Mensaje original- 
From: Rick Murphy
Sent: Monday, January 24, 2011 5:31 PM
To: dx4win@mailman.qth.net
Subject: Re: [Dx4win] JT65A  LoTW

 If you want to submit it as JT65 you can do the following:

 In TQSL Go to FilePreferencesADIF Modes
 Select Add
 Under ADIF Mode type JT65A, Under resulting TQSL mode select JT65.
 By doing this all of your JT65A QSOs will be entered into LoTW as the base 
 type of JT65.

It's better to create a map from JT65A to DATA since that's what it
is, a DATA mode contact. LoTW doesn't care about modes when matching
QSOs, just Mode Groups.

 Version 1.13 might handle it directly. Don't know. I didn't know there was 
 a 1.13 till this morning.

I added several new mode mappings to the 1.12 kit which the ARRL used
as the basis of 1.13 so it may be in there already.
73,
-Rick
-- 
Rick Murphy, CISSP-ISSAP, K1MU/4, Annandale VA USA
__
Dx4win mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Dx4win@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html 

__
Dx4win mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Dx4win@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Dx4win] JT65A LoTW

2011-01-24 Thread Jim Reisert AD1C 
On Sun, Jan 23, 2011 at 2:47 PM, LU5FF - Javier lu...@yahoo.com.ar wrote:

 OK Jim, I glue a picture ..
 ignore giving, shoot me a list of all stations on the way JT65A,
 I copy some ..

 Signing using CALL=LU5FF, DXCC=100
 Error: Invalid MODE (JT65A) on line 4
 QSO_DATE: 20100521
 TIME_ON: 224500
 CALL: RA0AUQ
 MODE: JT65A
 BAND: 20m
 LOTW_QSLSDATE:


This is an error in the TQSL program.  Do you have the latest version (1.13)?

You will need to contact someone in ARRL LoTW if you get this error.
Try lotw-h...@arrl.org

73 - Jim AD1C

-- 
Jim Reisert AD1C, jjreis...@alum.mit.edu, http://www.ad1c.us
__
Dx4win mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Dx4win@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Dx4win] JT65A LoTW

2011-01-24 Thread Loren Hunt 
The version of TQSL you are running doesn't know what JT65A is. I'm still 
running 1.11 and it doesn't show it. It does know about JT65. If you want to 
submit it as JT65 you can do the following:

In TQSL Go to FilePreferencesADIF Modes
Select Add
Under ADIF Mode type JT65A, Under resulting TQSL mode select JT65.
By doing this all of your JT65A QSOs will be entered into LoTW as the base type 
of JT65.

Version 1.13 might handle it directly. Don't know. I didn't know there was a 
1.13 till this morning.

73
AD6ZJ, Loren


--- On Mon, 1/24/11, Jim Reisert AD1C jjreis...@alum.mit.edu wrote:

From: Jim Reisert AD1C jjreis...@alum.mit.edu
Subject: Re: [Dx4win] JT65A  LoTW
To: LU5FF - Javier lu...@yahoo.com.ar
Cc: dx4win@mailman.qth.net
Date: Monday, January 24, 2011, 9:18 AM

On Sun, Jan 23, 2011 at 2:47 PM, LU5FF - Javier lu...@yahoo.com.ar wrote:

 OK Jim, I glue a picture ..
 ignore giving, shoot me a list of all stations on the way JT65A,
 I copy some ..

 Signing using CALL=LU5FF, DXCC=100
 Error: Invalid MODE (JT65A) on line 4
 QSO_DATE: 20100521
 TIME_ON: 224500
 CALL: RA0AUQ
 MODE: JT65A
 BAND: 20m
 LOTW_QSLSDATE:


This is an error in the TQSL program.  Do you have the latest version (1.13)?

You will need to contact someone in ARRL LoTW if you get this error.
Try lotw-h...@arrl.org

73 - Jim AD1C

-- 
Jim Reisert AD1C, jjreis...@alum.mit.edu, http://www.ad1c.us
__
Dx4win mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Dx4win@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
__
Dx4win mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Dx4win@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Dx4win] JT65A LoTW

2011-01-24 Thread Rick Murphy 
 If you want to submit it as JT65 you can do the following:

 In TQSL Go to FilePreferencesADIF Modes
 Select Add
 Under ADIF Mode type JT65A, Under resulting TQSL mode select JT65.
 By doing this all of your JT65A QSOs will be entered into LoTW as the base 
 type of JT65.

It's better to create a map from JT65A to DATA since that's what it
is, a DATA mode contact. LoTW doesn't care about modes when matching
QSOs, just Mode Groups.

 Version 1.13 might handle it directly. Don't know. I didn't know there was a 
 1.13 till this morning.

I added several new mode mappings to the 1.12 kit which the ARRL used
as the basis of 1.13 so it may be in there already.
73,
-Rick
-- 
Rick Murphy, CISSP-ISSAP, K1MU/4, Annandale VA USA
__
Dx4win mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Dx4win@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Dx4win] JT65A LoTW

2011-01-23 Thread LU5FF - Javier 
hello to the group.
These days I was making some contacts JT65A
but when exported to LoTW gives me error in the mode ..
I tried just putting JT65 and gives me error as well.
anyone can help me?

Javi LU5FF
__
Dx4win mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Dx4win@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Dx4win] JT65A LoTW

2011-01-23 Thread Jim Reisert AD1C 
On Sun, Jan 23, 2011 at 12:42 PM, LU5FF - Javier lu...@yahoo.com.ar wrote:

 hello to the group.
 These days I was making some contacts JT65A
 but when exported to LoTW gives me error in the mode ..
 I tried just putting JT65 and gives me error as well.
 anyone can help me?

Please copy/paste the error message from TQSL.  That will help narrow
down whether the problem is in DX4WIN or LoTW.

-- 
Jim Reisert AD1C, jjreis...@alum.mit.edu, http://www.ad1c.us
__
Dx4win mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Dx4win@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html