RE: [Elecraft] Microphone preamp and Heils
Dave, As far as the connections to the mic, yes, you will be 'good to go' if you use the Kenwood adapter and wire the K2 for the Kenwood configuration.. Whether you will want a preamp or not with that HC5 element is an entirely different question. For use with your HC5 element Proset, you might want to make the changes to the KSB2 board suggested by Jim Brown - Jim is an expert in the Pro-Audio field and has done a lot with ham radio too, so if Jim found those changes helpful, I do not boubt his word, in fact I may make those changes here too just to see what happens. In any case, you do not have your K2 completely built yet, so do not modify anything until you complete the kit and have things up and running. Of course, there is another alternative if you use only the boom/headset type mic - the Elecraft Proset-K2 is still available from Elecraft. I really don't know what happened with the MH2 and MD2 mics - they were good although I do recall a few complaints about the MH2 which was the handheld mic (in an impact resistant hard plastic case) - the desk mic (MD2) is a very nice metal body microphone. I have both here. If you can find someone selling the MH2 or the MD2, you may want to check it out (I am not giving up mine!). 73, Don W3FPR > -Original Message- > > Never did get a clear answer on this. If I wire the K2 up for the > Kenwood, and I have a Heil Pro Headset with the Kenwood adapter, I will > be good to go? > > Curious, why did they stop making the Elecraft associated mike? Was it > plastic or metal? > > David Wilburn > [EMAIL PROTECTED] > > -- No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.5.441 / Virus Database: 268.18.1/690 - Release Date: 2/16/2007 2:25 PM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Z6, grounded can?
FB, it was just that we had grounded all the other cans, so I wasn't sure. Thanks. David Wilburn [EMAIL PROTECTED] Don Wilhelm wrote: Dave, Congratulations on your progress. Don't worry about the empty holes - all holes are not filled, many are via holes to get a signal (or ground) from the top of the board to the bottom. If you need to check anything else of that nature, look at the parts placement diagram near the end of the manual, you will find it quite helpful. It does not show the holes, just the component placements. 73, Don W3FPR -Original Message- I'm installing T6 (yes there is a god, this is the last of the toroids for a little bit) and noticed a hole next to Z6. I did not see anything in the text, but the holes on either side of the can are in the ground plane so I was not sure. -- David Wilburn [EMAIL PROTECTED] -- No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.5.441 / Virus Database: 268.18.1/690 - Release Date: 2/16/2007 2:25 PM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Microphone preamp and Heils
Never did get a clear answer on this. If I wire the K2 up for the Kenwood, and I have a Heil Pro Headset with the Kenwood adapter, I will be good to go? Curious, why did they stop making the Elecraft associated mike? Was it plastic or metal? David Wilburn [EMAIL PROTECTED] David Wilburn wrote: Just curious of why the focus on the ICOM mikes? When I looked at the drawing for the pins on the front panel, it looked like the Kenwood was the least complicated to wire. A bit off topic, the Heil website does not show the hand mikes anymore. Well not a 'real' hand mike that sits and your hand as something rugged. They have these little microphone mikes. Not something that I'm interested in connecting to any of my radios. If I want a hands free setup, I'll use a headset and boom. Bar that, if I want to talk on a mike and listen via the speaker, I want a substantial mike that feels like I have something in my hand. My current plan is to wire my K2 up for the Kenwood microphone. My other radio is a TS-570. The assumption on my part, is that I will then be able to use my Heil headset on both the Kenwood and the K2. Is this a valid assumption? David Wilburn [EMAIL PROTECTED] Don Wilhelm wrote: The Heil microphone preamps are required for the Heil microphones using the HC4 and HC5 elements. The electret elements do not need a preamp (but they do need a resistor at the mic jack). The Heil mics designated for use with Icom transceivers are usually of the electret typw and work quite well with the K2. Remember that Heil has a wide variety of mics, just saying that you are using a Heil mic is not sufficient information, one must specify WHICH Heil mics - they are not created equal. I guess an anology is that you would not refer to an automobile as a General Motors car - you must specify if it is a Chevrolet, a Buick, a Cadillac, etc., and in many cases one must also specify which variety of Chevrolet, Buick, etc. Heil mics are much like that. So, yes choose the Icom mics if possible, but if you prefer those with the HC4 or HC5 elements (those elemetns have low ouput), you should plan to add a mic preamp. As far as I know, no PC boards or kits are available for the mic preamps. 73, Don W3FPR -Original Message- Hi, sorry if this repeats previous information request, but I did a lot of searching and didn't find anything directly on point (even though there were several threads on preamps and Heils, etc.) I downloaded the Microphone Pre-Amp for Heil schematic on the Elecraft website. My questions are: 1. Does anybody make a PCB for this project? I imagine all these parts are available from Radio Shack or Mouser? 2. Does the preamp make the microphones work really well, or is it just something that "gets you by?" 3. As far as Heil microphone modules go, if I build the preamp, and want to buy the Classic, can I use any module, like the Pro, HC-5, HC-4, etc., or should I get the ICOM only module, which I believe is an electret module. I am a bit confused about all this. I asked Elecraft and they said I should get the electret module. Bob Heil said the Classic was not a good choice for the K2 and he suggested his iCM mic for ICOM. Doesn't the iCM mic have the same electret element that the Classic with the IC element has? If all I needed was an electret element, do I need the preamp at all, or does it make the electret work even better? 4. Once I build the preamp, is it something that I can tuck into the microphone itself (like a Heil Classic) or does it go inside the K2 or do I need to put it into it's own little enclosure. Thanks for your help. I am a new ham, and am trying to sort through all this stuff. Christ Kacoyannakis K4CMK -- No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.5.441 / Virus Database: 268.17.39/686 - Release Date: 2/14/2007 7:54 AM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] Z6, grounded can?
Dave, Congratulations on your progress. Don't worry about the empty holes - all holes are not filled, many are via holes to get a signal (or ground) from the top of the board to the bottom. If you need to check anything else of that nature, look at the parts placement diagram near the end of the manual, you will find it quite helpful. It does not show the holes, just the component placements. 73, Don W3FPR > -Original Message- > > I'm installing T6 (yes there is a god, this is the last of the toroids > for a little bit) and noticed a hole next to Z6. I did not see anything > in the text, but the holes on either side of the can are in the ground > plane so I was not sure. > -- > > David Wilburn > [EMAIL PROTECTED] > -- No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.5.441 / Virus Database: 268.18.1/690 - Release Date: 2/16/2007 2:25 PM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] KAT2 CALS Problem
that was probably it. i went through the bands after i posted and made sure all the bands selected ant1. seems to be working fine for now. 73 jim ab3cv - Original Message - From: "k4zm" <[EMAIL PROTECTED]> To: "Jim Miller" <[EMAIL PROTECTED]> Sent: Friday, February 16, 2007 7:36 PM Subject: Re: [Elecraft] KAT2 CALS Problem I would bet that the other antenna input is selected on 15 meters ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K2 100W kits for sale
Hello, Well, after years of owning my own business and having little time for operating and less for building, I'm going to part with my K2 kits as a package deal (don't want to split package) and save someone a couple hundred bucks. All kits are still in original packages with nothing soldered or assembled. I'm selling for $1500 (UPS ground shipping included) the following: K2: HF XCVR S/N 3271 mcu ver 2.03d, ioc ver 1.07 KSB2: SSB Option, fw ver 1.07 KNB2: Noise Blanker PLL temp control mod kit KPA100: 100W Amp, fw ver 1.06 KAT100-1: 150W ATU, fw ver 1.03 KDSP2: Advanced DSP Filter ETS15: 1.5" Tilt Stand (shorter stand for stacking K2 and KAT100-1) MH2: Handmike that elecraft offered from Heil K7NUU dust cover: had it custom made to cover both K2 and Kat1100-1. It does have my callsign embroidered, but with a little engineering... Well there you have it. I'll ship right away with a money order or cashier's check. Please email if you have any questions. Thanks, Russ W9EL _ http://homepage.msn.com/zune?icid=hmetagline ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Z6, grounded can?
I'm installing T6 (yes there is a god, this is the last of the toroids for a little bit) and noticed a hole next to Z6. I did not see anything in the text, but the holes on either side of the can are in the ground plane so I was not sure. -- David Wilburn [EMAIL PROTECTED] ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] KAT2 CALS Problem
I'm nearing the end of my K2/KAT2 checkout and I'm to the point of measuring the SWR on each band. All the bands show a 1.0 -1 indication except 15M which displays a HI CUR message and a 9.9 -1 indication. I upped the CAL CUR level to 3A and I still get this indication. Any ideas on where to start looking? 73 jim ab3cv ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K2 lost sidetone?
Don, you are exactly correct, thanks again... -J On 2/16/07, Don Wilhelm <[EMAIL PROTECTED]> wrote: Jeff, Your sidetone source likely was switched for some reason or other - maybe by an 'extra' finger press while in the menu Go back into the menu and dial up ST L, press EDIT to move the cursor over to the right side and then tap DISPLAY to toggle the sidetone source. When you hear the sidetone, stop and exit from the menu. In some rare instances, it may take a few 'toggles' to get things to switch properly, so try it several times. If you have a post SN 3000 K2 (or have put the sidetone source change on an older K2 because you added the KPA100 or KIO2) your sidetone source should be 'U8 - 4' - you will see the source displayed briefly each time it is toggled. 73, Don W3FPR > -Original Message- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] Behalf Of Jeff Kinzli > Sent: Friday, February 16, 2007 5:06 PM > To: Elecraft Mail Posting > Subject: [Elecraft] K2 lost sidetone? > > > Oh man, what timing...2 hours before the start of the contest, and I > went in and did CAL tPA to set the ambient temp of the KPA100, and > when I came out of the menus, I had no sidetone anymore! > > Going through all the menus, all the side tone settings look correct. > The rig hears and transmits fine, but the sidetone is silent. > > I thought I might need to reset back to defaults, but I think that > resets all the filters and BFO, etc., right? If that's the case, I've > gotta go through realignment again? I'll miss the beginning of the > contest :( I'm going to miss it anyhow though at this point. > > Any ideas short of disassembling and resetting? > > Thanks, > -J > ___ > Elecraft mailing list > Post to: Elecraft@mailman.qth.net > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > -- > No virus found in this incoming message. > Checked by AVG Free Edition. > Version: 7.5.441 / Virus Database: 268.18.1/690 - Release Date: > 2/16/2007 2:25 PM > -- No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.5.441 / Virus Database: 268.18.1/690 - Release Date: 2/16/2007 2:25 PM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] K2 lost sidetone?
Jeff, Your sidetone source likely was switched for some reason or other - maybe by an 'extra' finger press while in the menu Go back into the menu and dial up ST L, press EDIT to move the cursor over to the right side and then tap DISPLAY to toggle the sidetone source. When you hear the sidetone, stop and exit from the menu. In some rare instances, it may take a few 'toggles' to get things to switch properly, so try it several times. If you have a post SN 3000 K2 (or have put the sidetone source change on an older K2 because you added the KPA100 or KIO2) your sidetone source should be 'U8 - 4' - you will see the source displayed briefly each time it is toggled. 73, Don W3FPR > -Original Message- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] Behalf Of Jeff Kinzli > Sent: Friday, February 16, 2007 5:06 PM > To: Elecraft Mail Posting > Subject: [Elecraft] K2 lost sidetone? > > > Oh man, what timing...2 hours before the start of the contest, and I > went in and did CAL tPA to set the ambient temp of the KPA100, and > when I came out of the menus, I had no sidetone anymore! > > Going through all the menus, all the side tone settings look correct. > The rig hears and transmits fine, but the sidetone is silent. > > I thought I might need to reset back to defaults, but I think that > resets all the filters and BFO, etc., right? If that's the case, I've > gotta go through realignment again? I'll miss the beginning of the > contest :( I'm going to miss it anyhow though at this point. > > Any ideas short of disassembling and resetting? > > Thanks, > -J > ___ > Elecraft mailing list > Post to: Elecraft@mailman.qth.net > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > -- > No virus found in this incoming message. > Checked by AVG Free Edition. > Version: 7.5.441 / Virus Database: 268.18.1/690 - Release Date: > 2/16/2007 2:25 PM > -- No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.5.441 / Virus Database: 268.18.1/690 - Release Date: 2/16/2007 2:25 PM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] n-gen, dl1
Good going and you picked the right time. They just got the parts back in stock for some kits. I just got a tracking email on 2 test kits I've got coming. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Re: K2 lost sidetone? (FIXED)
In my stressing, I didn't think to check the archives...found the answer here: http://www.ac6rm.net/mailarchive/html/elecraft-list/2006-08/msg00751.html Problem solved. Pfew! Cyu in the contest ;) -J On 2/16/07, Jeff Kinzli <[EMAIL PROTECTED]> wrote: Oh man, what timing...2 hours before the start of the contest, and I went in and did CAL tPA to set the ambient temp of the KPA100, and when I came out of the menus, I had no sidetone anymore! Going through all the menus, all the side tone settings look correct. The rig hears and transmits fine, but the sidetone is silent. I thought I might need to reset back to defaults, but I think that resets all the filters and BFO, etc., right? If that's the case, I've gotta go through realignment again? I'll miss the beginning of the contest :( I'm going to miss it anyhow though at this point. Any ideas short of disassembling and resetting? Thanks, -J ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] n-gen, dl1
Hey Elecrafters, Ok now, the check is in mail! Iv'e ordered the N-GEN and DL1. I am sure these tools will be of great value for me in future endevours. I may get a couple more items before I order the K1 kit. As a preliminary, I will obtain a less comprehensive (and expensive) kit from another company. While surfing the web I was saw a few I might try. When I am satisified that my level of competence is adequate to the task, I shall endevour to put together the K1. I AM BACK IN THE GAME!! Dennis Vavra AD5LY ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K2 lost sidetone?
Oh man, what timing...2 hours before the start of the contest, and I went in and did CAL tPA to set the ambient temp of the KPA100, and when I came out of the menus, I had no sidetone anymore! Going through all the menus, all the side tone settings look correct. The rig hears and transmits fine, but the sidetone is silent. I thought I might need to reset back to defaults, but I think that resets all the filters and BFO, etc., right? If that's the case, I've gotta go through realignment again? I'll miss the beginning of the contest :( I'm going to miss it anyhow though at this point. Any ideas short of disassembling and resetting? Thanks, -J ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] A new perspective
I think (not sure here) the techniques and needed skills are the same with the K2 or K1. The difference is just scale. The K2 is just more of the same. Of course, more means there is more chance to do something wrong, but I don't think the K1 is any easier (or tougher) to build, just shorter. I've not built a K1, only a K2 plus a few accessories. I found I did a better job on the K2 than the KPA100 simply because I was scared to death by the K2 so I worked slowly, READ and FOLLOWED all the instructions to a "T" and made only 1 mistake (one part in the wrong place). With the KPA100 I was a bit more confident and made more mistakes. Same with the AF mini-module. It is small and should have been a perfect build but lack of attention to detail caused me to put one part in the wrong place. You can always hire someone to build it for you. There is no shame in that, some of us like to build, some don't. Either way, we can all enjoy a great radio. - Keith N1AS - - K2 5411.ssb.100 - -Original Message- From: Dennis Vavra What is the level of difficulty in contructing the K1 compared to the K2? ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] KPA100 IMD Distortion Figures
Thanks, Larry, those figures are in themselves impressive. Of course, a lot depends on the mesurement equipment and conditions. Worth adding perhaps to the Elecraft resource list.. My L-4's -33db compared to single tone (-39db cf. pep), would in that case be the limiting factor. Maybe a good excuse for a new rig. 73 Wyn, VR2AX - Original Message - From: "Larry Phipps" <[EMAIL PROTECTED]> To: "Wyn Hughes" <[EMAIL PROTECTED]> Cc: Sent: Friday, February 16, 2007 9:48 PM Subject: Re: [Elecraft] KPA100 IMD Distortion Figures > Take a look at the tests run by Jack, K8ZOA, using his Z90 Panadapter > kit at cliftonlaboratories.com Click on the IMD Measurements link. He > shows the test methodology, and results from several rigs, including his > K2/100. > > 73, > Larry N8LP > > > > Wyn Hughes wrote: > > Hello Group, > > > > Has anyone measured, or have any information, regarding the 3rd/5th order IMD performance of the barebones KPA100, based on a two-tone test? > > > > I have some figures for the base K2, courtesy of the ARRL review. I might even have seen figures for the K2/100, but can't seem to locate them at present. If anyone can also supply these figures, I would be grateful. > > > > > > 73 > > Wyn, V2AX > > > > ___ > > Elecraft mailing list > > Post to: Elecraft@mailman.qth.net > > You must be a subscriber to post to the list. > > Subscriber Info (Addr. Change, sub, unsub etc.): > > http://mailman.qth.net/mailman/listinfo/elecraft > > > > Help: http://mailman.qth.net/subscribers.htm > > Elecraft web page: http://www.elecraft.com > > > > > > ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] KPA100 IMD Distortion Figures
Take a look at the tests run by Jack, K8ZOA, using his Z90 Panadapter kit at cliftonlaboratories.com Click on the IMD Measurements link. He shows the test methodology, and results from several rigs, including his K2/100. 73, Larry N8LP Wyn Hughes wrote: Hello Group, Has anyone measured, or have any information, regarding the 3rd/5th order IMD performance of the barebones KPA100, based on a two-tone test? I have some figures for the base K2, courtesy of the ARRL review. I might even have seen figures for the K2/100, but can't seem to locate them at present. If anyone can also supply these figures, I would be grateful. 73 Wyn, V2AX ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] KPA100 IMD Distortion Figures
Hello Group, Has anyone measured, or have any information, regarding the 3rd/5th order IMD performance of the barebones KPA100, based on a two-tone test? I have some figures for the base K2, courtesy of the ARRL review. I might even have seen figures for the K2/100, but can't seem to locate them at present. If anyone can also supply these figures, I would be grateful. 73 Wyn, V2AX ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
