Re: [Elecraft] [K2] TX Issue in Part III checks
Brian, The DC voltages on Q24 are based on a properly working K2 at the 5 watt power level. What you now have is a K2 that will not develop power to the RF Detector, so the power control circuits will react to force the RF voltages to their maximum - the control element for that is the VALC voltage to Q24, and that will go to its maximum since there is zero power detected. I note that you measure zero volts at the drain of Q24, but VALC at the source (CB emitter of Q8) is at 7.4 volts. Something is broken (not soldered) between those two points because the only component between the two is R98 which should not be drawing any current and therefore should not have any voltage drop (given your situation with no power output). Look for unsoldered connections (don't forget the connectors) or solder bridges in that signal path. Look critically at you soldering - if the solder did not flow out to an almost invisible edge on the solder pad, it is suspect, and the likely cause is that the solder pad did not receive enough heat. Re-flow the solder on all suspect connections using a hot (750 deg F) iron, and add a bit of flux if necessary. 73, Don W3FPR On 1/8/2011 10:44 PM, Brian Handy wrote: > Hi All, > > I've been working on my K2 and I'm on the home stretch. I had to dabble a bit > to find a cold solder joint in the Part II checks, but eventually got a > home-brewed test oscillator to reach through on 40m! Quite happy with things > so > far, and learning a lot. > > I still have a lot to learn about the transmitter side though, that doesn't > work. When I first hit 'tune' in the Part III checks, I noticed high current > on > the power supply, high current on the front panel, and changing the power > level > didn't help, it was always high draw. > > It didn't take much of this to zorch the PA finals and short things straight > to > ground. Nothing worked until I pulled T3, and while I had the soldering out I > took out the PAs and started looking around and reading the mail archives. > > I noted one suggestion from Don to someone else and checked the voltages on > base > on the finals - both are around 0.65V, which I think is OK. > > I realize things won't be quite the same without the PAs there and proper > feedback happening, but ... I then started going through all the voltages on > the > RF board with TUNE on. Everything looked pretty much fine except for Q24 ~ > > Leg - Expected - Measured: > G- 0V - 5.6V > S - 1.2 - 2.5V > D - 13V - 0V > > That doesn't look right at all to me. Exploring further, I started chasing > VALC > down the rabbit hole. > > Pin 2 of U8 (V PWR) seems to vary between 3.8-5V as I turn the PWR knob in > TUNE. I decided that was OK. > > Pin 1 of U10A doesn't move around a lot, only up and down about 0.1V. Finally > the emitter of Q8 (V ALC) seems stuck at 7.4V. > > I was firmly confused at this point, so went back and started checking Control > Board voltages per the page of expected readings in the back of the manual > with > CAL FCTR turned on. Everything seems turned off when I do that and I'm seeing > pretty much 0V everywhere. > > I'm a bit saturated at the moment, but thought I would ask if this sounds like > I'm on the right track, or if I have to get to poking elsewhere ... > > > > Cheers and thanks in advance, > > Brian Handy > AE7JW > Tokyo, Japan > > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Backup/Restore current configuration via file
You can use the K3 Utility Program to save the configuration and then restore it later if you need to. Or are you wanting a hard copy of the configuration info? -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of ik1bxn Sent: Saturday, January 08, 2011 12:25 PM To: elecraft@mailman.qth.net Subject: [Elecraft] Backup/Restore current configuration via file Is it a way to dump to a file the current k3 configuration ? I think to all settings, for example to activate digimodes with my Signalink interface I touched mode, line level input and so on. My goal should be to have a reliable restore point to rollback in cause of my errors during future setting modification temptatives. Many thanks to everybody, HNY 2011 and 73 - Giorgio -- View this message in context: http://elecraft.365791.n2.nabble.com/Backup-Restore-current-configuratio n-via-file-tp5902987p5902987.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K2] TX Issue in Part III checks
On 1/8/2011 10:44 PM, Brian Handy wrote: > Hi All, > > I've been working on my K2 and I'm on the home stretch. I had to dabble a bit > to find a cold solder joint in the Part II checks, but eventually got a > home-brewed test oscillator to reach through on 40m! Quite happy with things > so > far, and learning a lot. > > I still have a lot to learn about the transmitter side though, that doesn't > work. When I first hit 'tune' in the Part III checks, I noticed high current > on > the power supply, high current on the front panel, and changing the power > level > didn't help, it was always high draw. > > It didn't take much of this to zorch the PA finals and short things straight > to > ground. Nothing worked until I pulled T3, and while I had the soldering out I > took out the PAs and started looking around and reading the mail archives. > > I noted one suggestion from Don to someone else and checked the voltages on > base > on the finals - both are around 0.65V, which I think is OK. > > I realize things won't be quite the same without the PAs there and proper > feedback happening, but ... I then started going through all the voltages on > the > RF board with TUNE on. Everything looked pretty much fine except for Q24 ~ > > Leg - Expected - Measured: > G- 0V - 5.6V > S - 1.2 - 2.5V > D - 13V - 0V > > That doesn't look right at all to me. Exploring further, I started chasing > VALC > down the rabbit hole. > > Pin 2 of U8 (V PWR) seems to vary between 3.8-5V as I turn the PWR knob in > TUNE. I decided that was OK. > > Pin 1 of U10A doesn't move around a lot, only up and down about 0.1V. Finally > the emitter of Q8 (V ALC) seems stuck at 7.4V. > > I was firmly confused at this point, so went back and started checking Control > Board voltages per the page of expected readings in the back of the manual > with > CAL FCTR turned on. Everything seems turned off when I do that and I'm seeing > pretty much 0V everywhere. > > I'm a bit saturated at the moment, but thought I would ask if this sounds like > I'm on the right track, or if I have to get to poking elsewhere ... > > > > Cheers and thanks in advance, > > Brian Handy > AE7JW > Tokyo, Japan > > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] [K2] TX Issue in Part III checks
Hi All, I've been working on my K2 and I'm on the home stretch. I had to dabble a bit to find a cold solder joint in the Part II checks, but eventually got a home-brewed test oscillator to reach through on 40m! Quite happy with things so far, and learning a lot. I still have a lot to learn about the transmitter side though, that doesn't work. When I first hit 'tune' in the Part III checks, I noticed high current on the power supply, high current on the front panel, and changing the power level didn't help, it was always high draw. It didn't take much of this to zorch the PA finals and short things straight to ground. Nothing worked until I pulled T3, and while I had the soldering out I took out the PAs and started looking around and reading the mail archives. I noted one suggestion from Don to someone else and checked the voltages on base on the finals - both are around 0.65V, which I think is OK. I realize things won't be quite the same without the PAs there and proper feedback happening, but ... I then started going through all the voltages on the RF board with TUNE on. Everything looked pretty much fine except for Q24 ~ Leg - Expected - Measured: G- 0V - 5.6V S - 1.2 - 2.5V D - 13V - 0V That doesn't look right at all to me. Exploring further, I started chasing VALC down the rabbit hole. Pin 2 of U8 (V PWR) seems to vary between 3.8-5V as I turn the PWR knob in TUNE. I decided that was OK. Pin 1 of U10A doesn't move around a lot, only up and down about 0.1V. Finally the emitter of Q8 (V ALC) seems stuck at 7.4V. I was firmly confused at this point, so went back and started checking Control Board voltages per the page of expected readings in the back of the manual with CAL FCTR turned on. Everything seems turned off when I do that and I'm seeing pretty much 0V everywhere. I'm a bit saturated at the moment, but thought I would ask if this sounds like I'm on the right track, or if I have to get to poking elsewhere ... Cheers and thanks in advance, Brian Handy AE7JW Tokyo, Japan __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] WTB K2 KI02
Now that I have some XV transverters, I'd like to be able to daisey chain them as well as use logging software. Does anyone want to sell a well built KI02? With Alpha One COPD and arthritis in my fingers what was a trivial build a few years ago would be a challenge today. Pse contact me at QRZ address. Doug K4LY __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] Elecraft CW Net Announcement
Good Evening, More snow is falling as I sit by the fire. Not too cold with very little wind so it is pretty nice outside. I am right at snow line so it has come and gone over the last week. Never quite goes away and never really builds up either. Kind of a steady state system. We did get some icing a few days ago but that was followed by some warm rain. The roads are in fair condition but one needs to be careful on the shaded corners where it can be slippery. Considering some of the drop offs we have up here it could get rather exciting if you slip off the road. Luckily there are plenty of large trees to slow the descent :) Propagation has been alright this week so I expect the nets tomorrow to gather a fair number of folks. Please join us tomorrow afternoon and evening. 1) Hail signs (first letter or two of the suffix of your call) 2) NCS help (as well as QSP/QNP help) Sunday 2300z (Sunday 3 PM PST) 14050 kHz Monday 0100z (Sunday 5 PM PST) 7045 kHz Stay well, Kevin. KD5ONS - __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] Elecraft SSB Net announcement
Hi gang, The weekly SSB net will meet tomorrow (1/9/11) at 1800z on 14.314 MHz. Ken, KO5Y, with help from Paul, AD5SX, will be the net control. Have a goood net. 73, Phil NS7P __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [KX1] Xmit frequency differs from display on one band
Chip, First, calibrate the BFO by listening to an AM station. If you have the KXB3080 installed, use 10 MHz WWV (but any AM station will do - make LSB and USB sound the same - the instructions are in the manual. After that, use the DDS menu (again as instructed in the manual), adjust the menu so the station is received at the proper frequency on the dial. You must do both the BFO and the DDS calibration to make the frequency display correct. 73, Don W3FPR On 1/8/2011 6:35 PM, Chip Stratton wrote: > Using the DDS menu, I have calibrated the KX1 so that the transmitted > carrier frequency is displayed accurately on the 20 meter band. However, on > the 40 meter band the carrier is 350 Hz higher than shown on the display. > > Am I overlooking something or is the disparity something I just need to live > with? > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] [KX1] Xmit frequency differs from display on one band
Using the DDS menu, I have calibrated the KX1 so that the transmitted carrier frequency is displayed accurately on the 20 meter band. However, on the 40 meter band the carrier is 350 Hz higher than shown on the display. Am I overlooking something or is the disparity something I just need to live with? Thanks, Chip AE5KA __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] (no subject)
I apologize for the Political email that got sent to all my contacts. I did not do it. Someone hacked into my laptop and used my gmail account. Paul Gates __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] not needed
ref the msg on term limits spent 25 min's getting that msg off my computer. got over 50 of them b4 i could hit spam button. have no idea what this has to do with elecraft. or more importently how that uh hum" gentleman" got my email adress. s/tony rowland __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Data modes issue
Jim, Line level is a LOT greater than microphone level. 73, Don W3FPR On 1/8/2011 3:45 PM, Jim Littlefield wrote: > The attenuation was disabled. I xm surprised at how high a level is required > to drive the K3. But everything is working now. > > - Jim WN1X > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Data modes issue
The attenuation was disabled. I xm surprised at how high a level is required to drive the K3. But everything is working now. - Jim WN1X On Jan 8, 2011, at 3:06 PM, Don Wilhelm wrote: > Jim, > > I just checked the Navigator documentation on the website. It does not state > whether line level output is available or not, but there is an option called > RF ATTN which by default inserts 20 dB attenuation into the audio output. > For use with the K3, I would think that should be set to No Attenuation. > > 73, > Don W3FPR > > On 1/8/2011 2:47 PM, Jim Littlefield wrote: >> Positive. My sound card is a US Interface Navigator. I can turn it's monitor >> speaker completely off and listen to the K3's monitor. >> >> - Jim WN1X >> __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] NR suddenly stopped working in SSB
Whoa, that's weird. It just started working again. Must be gremlins ;-) John K2QY __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Data modes issue
Do you have line-in enabled so you are not looking for the input on the mic in KD8NNU Sent from my Palm Pre on the Now Network from Sprint On Jan 8, 2011 2:58 PM, Don Wilhelmwrote: Jim, Are you getting enough audio into the K3? Set the K3 to TX TEST and look at the ALC bargraph. You should have 4 bars lighting solid with the 5th bar possibly blinking. If you are not seeing that indication on the ALC meter in the K3, you are not driving the Line-in with enough audio. The K3 "ALC" meter is also a "VU" meter on the lower part of the scale. Indication below 5 bars indicate no ALC is being generated - ALC action begins with the 5th bar. So if you followed the old advice that you should not have any ALC indication for DATA modes, that old advice must be modified for the K3. The K3 Line-in expects to see line level signals. If you are using an external interface, some by default use microphone level for the output and you must change a jumper in the box to bring it up to line level. 73, Don W3FPR On 1/8/2011 1:47 PM, Jim Littlefield wrote: > Just got my new K3 and everything is great about it except, sound card > data modes (PSK31, etc.) are not working. I put the radio in Data A > mode. When I transmit, the rig is keyed, I can hear audio via the > monitor function, but nothing is transmitted. I have tried cranking the > Mic gain (actually the line in gain) way up, but that doesn't help. I > have also confirmed the transmitter is not in test mode. > > Any suggestions? > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] NR suddenly stopped working in SSB
> > > Is AGC off? > > Grant/NQ5T > > On Jan 8, 2011, at 2:15 PM, John Fritze wrote: > >> Anyone have any idea why the NR (button 8) would suddenly stop working >> in SSB? I get a N/A message. I don't know if I set something wrong? >> It works fine in CW. >> >> Ideas? >> >> John >> K2QY > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] NR suddenly stopped working in SSB
Anyone have any idea why the NR (button 8) would suddenly stop working in SSB? I get a N/A message. I don't know if I set something wrong? It works fine in CW. Ideas? John K2QY __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Data modes issue
Jim, I'm using MixW, I powered up the K3 and you do not need VOX to Key the K3. I think Don may have hit the nail on the Head , check ALC. 73 Ken K5DNL - Original Message From: Jim Littlefield To: Ken Roberson Cc: Elecraft Mailing List Sent: Sat, January 8, 2011 1:06:25 PM Subject: Re: [Elecraft] Data modes issue Ken, The rig is being keyed, but I just tried turning VOX on, but no change in behavior. This really weird. On 1/8/2011 1:57 PM, Ken Roberson wrote: > Jim, > > Try turning on the VOX. > > Ken K5DNL > --- > > > > - Original Message > From: Jim Littlefield > To: Elecraft Mailing List > Sent: Sat, January 8, 2011 12:47:37 PM > Subject: [Elecraft] Data modes issue > > Just got my new K3 and everything is great about it except, sound card > data modes (PSK31, etc.) are not working. I put the radio in Data A > mode. When I transmit, the rig is keyed, I can hear audio via the > monitor function, but nothing is transmitted. I have tried cranking the > Mic gain (actually the line in gain) way up, but that doesn't help. I > have also confirmed the transmitter is not in test mode. > > Any suggestions? > -- 73 de Jim Littlefield WN1X __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Data modes issue
Jim, I just checked the Navigator documentation on the website. It does not state whether line level output is available or not, but there is an option called RF ATTN which by default inserts 20 dB attenuation into the audio output. For use with the K3, I would think that should be set to No Attenuation. 73, Don W3FPR On 1/8/2011 2:47 PM, Jim Littlefield wrote: > Positive. My sound card is a US Interface Navigator. I can turn it's monitor > speaker completely off and listen to the K3's monitor. > > - Jim WN1X > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Data modes issue
Jim, Check to see if audio is coming out of your computer, And set up K3 in data mode. Not sure what program you use, I'm using, However I have not been on psk for a while. Ken K5DNL - - Original Message From: Jim Littlefield To: Ken Roberson Cc: Elecraft Mailing List Sent: Sat, January 8, 2011 1:06:25 PM Subject: Re: [Elecraft] Data modes issue Ken, The rig is being keyed, but I just tried turning VOX on, but no change in behavior. This really weird. On 1/8/2011 1:57 PM, Ken Roberson wrote: > Jim, > > Try turning on the VOX. > > Ken K5DNL > --- > > > > - Original Message > From: Jim Littlefield > To: Elecraft Mailing List > Sent: Sat, January 8, 2011 12:47:37 PM > Subject: [Elecraft] Data modes issue > > Just got my new K3 and everything is great about it except, sound card > data modes (PSK31, etc.) are not working. I put the radio in Data A > mode. When I transmit, the rig is keyed, I can hear audio via the > monitor function, but nothing is transmitted. I have tried cranking the > Mic gain (actually the line in gain) way up, but that doesn't help. I > have also confirmed the transmitter is not in test mode. > > Any suggestions? > -- 73 de Jim Littlefield WN1X __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Data modes issue
Jim, Are you getting enough audio into the K3? Set the K3 to TX TEST and look at the ALC bargraph. You should have 4 bars lighting solid with the 5th bar possibly blinking. If you are not seeing that indication on the ALC meter in the K3, you are not driving the Line-in with enough audio. The K3 "ALC" meter is also a "VU" meter on the lower part of the scale. Indication below 5 bars indicate no ALC is being generated - ALC action begins with the 5th bar. So if you followed the old advice that you should not have any ALC indication for DATA modes, that old advice must be modified for the K3. The K3 Line-in expects to see line level signals. If you are using an external interface, some by default use microphone level for the output and you must change a jumper in the box to bring it up to line level. 73, Don W3FPR On 1/8/2011 1:47 PM, Jim Littlefield wrote: > Just got my new K3 and everything is great about it except, sound card > data modes (PSK31, etc.) are not working. I put the radio in Data A > mode. When I transmit, the rig is keyed, I can hear audio via the > monitor function, but nothing is transmitted. I have tried cranking the > Mic gain (actually the line in gain) way up, but that doesn't help. I > have also confirmed the transmitter is not in test mode. > > Any suggestions? > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Data modes issue
Positive. My sound card is a US Interface Navigator. I can turn it's monitor speaker completely off and listen to the K3's monitor. - Jim WN1X On Jan 8, 2011, at 2:31 PM, "Joe Subich, W4TV" wrote: > > Are you sure you're hearing the audio from the K3 monitor and > not from other speakers attached to the computer? What sound > card software are you using? Are you sure it is configured to > use the soundcard attached to the radio and not the computer > "default" sound card if you have more than one (e.g., an interface > with built-in sound card)? > > 73, > > ... Joe, W4TV > > On 1/8/2011 2:04 PM, Jim Littlefield wrote: >> Yes, I definitely have the MIC SEL set to LINE IN and the LINE IN gain >> at 30. >> >> >> On 1/8/2011 1:57 PM, John Ragle wrote: >>> Check in particular... >>> >>> MIC SEL = LINE IN >>> >>> also >>> >>> LIN IN set to ~10-30 depending on band... >>> >>> My mic gain runs about "LINE 30" and the SignaLink (IF USING) has TX @ >>> 9 O'Clock and RX @ 11 or 12 O'Clock. (Again, IF USING SignaLink, both >>> jumpers that deal with audio olume are set to the "high" setting...see >>> instructions.) >>> >>> John Ragle -- W1ZI >>> >>> = >>> >>> On 1/8/2011 1:47 PM, Jim Littlefield wrote: Just got my new K3 and everything is great about it except, sound card data modes (PSK31, etc.) are not working. I put the radio in Data A mode. When I transmit, the rig is keyed, I can hear audio via the monitor function, but nothing is transmitted. I have tried cranking the Mic gain (actually the line in gain) way up, but that doesn't help. I have also confirmed the transmitter is not in test mode. Any suggestions? >>> >>> >> >> __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Data modes issue
No, it us definitely not in test mode. - Jim WN1X On Jan 8, 2011, at 2:38 PM, "Larry - K2GN" wrote: > Is the rig in the TEST Mode? > > TX light blinking. If so, you've accidently hit the Mode Up switch and held > it in for too long. > > de K2GN/Larry > > > > From: elecraft-boun...@mailman.qth.net > [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Jim Littlefield > Sent: Saturday, January 08, 2011 2:06 PM > To: Ken Roberson > Cc: Elecraft Mailing List > Subject: Re: [Elecraft] Data modes issue > > > > Ken, > > The rig is being keyed, but I just tried turning VOX on, but no change > in behavior. This really weird. > > > On 1/8/2011 1:57 PM, Ken Roberson wrote: >> Jim, >> >> Try turning on the VOX. >> >> Ken K5DNL >> --- >> >> >> >> - Original Message >> From: Jim Littlefield >> To: Elecraft Mailing List >> Sent: Sat, January 8, 2011 12:47:37 PM >> Subject: [Elecraft] Data modes issue >> >> Just got my new K3 and everything is great about it except, sound card >> data modes (PSK31, etc.) are not working. I put the radio in Data A >> mode. When I transmit, the rig is keyed, I can hear audio via the >> monitor function, but nothing is transmitted. I have tried cranking the >> Mic gain (actually the line in gain) way up, but that doesn't help. I >> have also confirmed the transmitter is not in test mode. >> >> Any suggestions? >> > > > -- > 73 de Jim Littlefield WN1X > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > > _ > > No virus found in this message. > Checked by AVG - www.avg.com > Version: 10.0.1191 / Virus Database: 1435/3367 - Release Date: 01/08/11 > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Data modes issue
Is the rig in the TEST Mode? TX light blinking. If so, you've accidently hit the Mode Up switch and held it in for too long. de K2GN/Larry From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Jim Littlefield Sent: Saturday, January 08, 2011 2:06 PM To: Ken Roberson Cc: Elecraft Mailing List Subject: Re: [Elecraft] Data modes issue Ken, The rig is being keyed, but I just tried turning VOX on, but no change in behavior. This really weird. On 1/8/2011 1:57 PM, Ken Roberson wrote: > Jim, > > Try turning on the VOX. > > Ken K5DNL > --- > > > > - Original Message > From: Jim Littlefield > To: Elecraft Mailing List > Sent: Sat, January 8, 2011 12:47:37 PM > Subject: [Elecraft] Data modes issue > > Just got my new K3 and everything is great about it except, sound card > data modes (PSK31, etc.) are not working. I put the radio in Data A > mode. When I transmit, the rig is keyed, I can hear audio via the > monitor function, but nothing is transmitted. I have tried cranking the > Mic gain (actually the line in gain) way up, but that doesn't help. I > have also confirmed the transmitter is not in test mode. > > Any suggestions? > -- 73 de Jim Littlefield WN1X __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html _ No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1191 / Virus Database: 1435/3367 - Release Date: 01/08/11 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] Backup/Restore current configuration via file
Is it a way to dump to a file the current k3 configuration ? I think to all settings, for example to activate digimodes with my Signalink interface I touched mode, line level input and so on. My goal should be to have a reliable restore point to rollback in cause of my errors during future setting modification temptatives. Many thanks to everybody, HNY 2011 and 73 - Giorgio -- View this message in context: http://elecraft.365791.n2.nabble.com/Backup-Restore-current-configuration-via-file-tp5902987p5902987.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Data modes issue
Ken, The rig is being keyed, but I just tried turning VOX on, but no change in behavior. This really weird. On 1/8/2011 1:57 PM, Ken Roberson wrote: > Jim, > > Try turning on the VOX. > > Ken K5DNL > --- > > > > - Original Message > From: Jim Littlefield > To: Elecraft Mailing List > Sent: Sat, January 8, 2011 12:47:37 PM > Subject: [Elecraft] Data modes issue > > Just got my new K3 and everything is great about it except, sound card > data modes (PSK31, etc.) are not working. I put the radio in Data A > mode. When I transmit, the rig is keyed, I can hear audio via the > monitor function, but nothing is transmitted. I have tried cranking the > Mic gain (actually the line in gain) way up, but that doesn't help. I > have also confirmed the transmitter is not in test mode. > > Any suggestions? > -- 73 de Jim Littlefield WN1X __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Data modes issue
Yes, I definitely have the MIC SEL set to LINE IN and the LINE IN gain at 30. On 1/8/2011 1:57 PM, John Ragle wrote: > Check in particular... > > MIC SEL = LINE IN > > also > > LIN IN set to ~10-30 depending on band... > > My mic gain runs about "LINE 30" and the SignaLink (IF USING) has TX @ > 9 O'Clock and RX @ 11 or 12 O'Clock. (Again, IF USING SignaLink, both > jumpers that deal with audio olume are set to the "high" setting...see > instructions.) > > John Ragle -- W1ZI > > = > > On 1/8/2011 1:47 PM, Jim Littlefield wrote: >> Just got my new K3 and everything is great about it except, sound card >> data modes (PSK31, etc.) are not working. I put the radio in Data A >> mode. When I transmit, the rig is keyed, I can hear audio via the >> monitor function, but nothing is transmitted. I have tried cranking the >> Mic gain (actually the line in gain) way up, but that doesn't help. I >> have also confirmed the transmitter is not in test mode. >> >> Any suggestions? >> > > -- 73 de Jim Littlefield WN1X __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Data modes issue
Jim, Try turning on the VOX. Ken K5DNL --- - Original Message From: Jim Littlefield To: Elecraft Mailing List Sent: Sat, January 8, 2011 12:47:37 PM Subject: [Elecraft] Data modes issue Just got my new K3 and everything is great about it except, sound card data modes (PSK31, etc.) are not working. I put the radio in Data A mode. When I transmit, the rig is keyed, I can hear audio via the monitor function, but nothing is transmitted. I have tried cranking the Mic gain (actually the line in gain) way up, but that doesn't help. I have also confirmed the transmitter is not in test mode. Any suggestions? -- 73 de Jim Littlefield WN1X __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] Data modes issue
Just got my new K3 and everything is great about it except, sound card data modes (PSK31, etc.) are not working. I put the radio in Data A mode. When I transmit, the rig is keyed, I can hear audio via the monitor function, but nothing is transmitted. I have tried cranking the Mic gain (actually the line in gain) way up, but that doesn't help. I have also confirmed the transmitter is not in test mode. Any suggestions? -- 73 de Jim Littlefield WN1X __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Power Gain Cal error
John, The latest Utility is 1.3.11.5. Try using that first. 73, Tom Childers Radio Amateur N5GE Licensed since 1976 QCWA Life Member 35102 ARRL Life Member Retired Professional C# Software developer http://www.n5ge.net On Sat, 8 Jan 2011 09:00:57 -0800 (PST), John_N1JM wrote: > >Must be doing something wrong. Using the utility I get this error for both 5w >and 50w cal: > >Elecraft K3 Utility Version 1.3.10.15 >OS Version 6.1 Build 7600 Windows 7/Windows Server 2008 R2 >Starting 50 watt calibration >Calibrating at 1.900 MHz >Elapsed time: 17 seconds >K3 did not respond to VFO A query (FA) >50 watt calibration failed > >FA responds fine on the command tester tab. > >73, >John N1JM __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] ERR 12v
Bingo, Ed! That did the trick!! Thanks a bunch es 73, Randy, KS4L On 1/7/2011 9:44 PM, Ed Gilliland wrote: > Hello Randy, > > I had ERR 12V alarms and recrimped the lugs on the wires that attach > to the circuit breaker. I've run two or three contests since with no > alarm messages. > > Good luck, Ed/W5TM > > - Original Message - From: "Randy Moore" > To: "Elecraft Discussion List" > Sent: Friday, January 07, 2011 8:47 PM > Subject: [Elecraft] [K3] ERR 12v > > >> I am working on an friends K3 (#4446), recently purchased used. When I >> got it, Power-On resulted in "ERR DSE." Firmware load failed, so I did >> EEINIT, and then the firmware loaded correctly. After going through >> filter setups to match the on-board filters, things seemed to be working >> correctly. But then I tried to increase power beyond 12w, and now I get >> the "ERR 12V", which my friend had seen before. When that error occurs, >> the KPA3 fans come on. Just for kicks, I tried to do the Tx Gain >> Calibration through the K3 Utility (dummy load attached), and even at >> the 5w level, it fails. >> >> The seller of this K3 says none of this was happening before he shipped >> the unit. >> >> I need some advice on how to proceed. >> >> Tnx es 73, >> Randy, KS4L > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3 Speaker Out? and P3 ?
Is it possible to direct the audio from the main Rx to the internal speaker (left channel audio) and the audio from the Sub Rx to an external speaker (right channel audio)? Is it possible to save the band (freq) to a menu FN button? I am fairly sure you cannot, but I thought I would ask anyway. Rich __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3 Power Gain Cal error
Must be doing something wrong. Using the utility I get this error for both 5w and 50w cal: Elecraft K3 Utility Version 1.3.10.15 OS Version 6.1 Build 7600 Windows 7/Windows Server 2008 R2 Starting 50 watt calibration Calibrating at 1.900 MHz Elapsed time: 17 seconds K3 did not respond to VFO A query (FA) 50 watt calibration failed FA responds fine on the command tester tab. 73, John N1JM -- View this message in context: http://elecraft.365791.n2.nabble.com/K3-Power-Gain-Cal-error-tp5902732p5902732.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] XV smokin' hot - no longer
Good news - I replaced the thermal pad between heat spreader and case with good old Thermalcote heatsink goo, and it made a huge difference. Case heats up right away and things cool off fast after TX. Did a lot of checking before lunch, all good. Then I went for a break. Bad news - U6 failed when I powered up again for final checkout before taking it off bench and hooking to rig. Zero output. Quick check showed nothing getting past SGA7489. It just died. Am wondering if this device was on its way out while I was testing, might explain power drops. I've ordered replacements from Digi-Key. Thanks for the input from several of you off list. 73 VE3MSC Colin __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3: Hears stations twice
If your radio is doing it, you will hear that on ALL loud radio signals. This would be especially true of the carrier on AM broadcast stations. If only on one signal, it's their problem. There are a LOT of transmitters that have transmitted frequencies well down besides the main transmission. A common one, heard on analog transmitters that are using a keyed audio tone through SSB circuitry to reduce manufacturing cost, is carrier balance in the balanced modulator, and ultimate filter rejection of the other sideband. These could be anywhere between 700 and 4000 Hz away depending on the circuit and settings. Your K3 does not do this (transmit artifacts of analog SSB generation) because it is digital and does not have a balanced modulator. 15 kHz SSB is generated by the transmit DAC directly from a number stream created by a firmware algorithm from the audio number stream created by running microphone audio through an analog to digital chip. The slightly unbalanced carrier and the opposite sideband that allow the analog artifacts simply do not exist anywhere. For a while the K3 TX had a clean and coherent microphonic spur on CW when using the MON tone and the internal speaker on CW. This has been remedied for some time now (see "stiffener" mod). 73, Guy. On Sat, Jan 8, 2011 at 5:29 AM, OE5CSP-Chris wrote: > > Hi, > > During the Christmas holidays I spent a lot of time on 80m and I came across > the problem mentioned on the reflector some time ago.Sometimes I can hear a > strong station twice.Yesterday,for example I heard a strong German station > on 3514 and a few khz down I heard the same signal again, but much weaker.I > did not use the NB or NR. This happened a few times already.Is this a known > issue and will it be fixed in the next firmware release? > > 73,Chris-OE5CSP > -- > View this message in context: > http://elecraft.365791.n2.nabble.com/K3-Hears-stations-twice-tp5865819p5902107.html > Sent from the [K3] mailing list archive at Nabble.com. > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] XMIT Key does not work
My XMIT key on my K3 stopped working Anyone have that? CW still works. NOT is test mode either. DISP key stopped working too. I was checking other buttons and all seem to work and then the DISP and XMIT button started working. HMM. This is weird. Anyone have any ideas? Lee k0WA In our day and age it seems that Common Sense is in short supply. If you don't have any Common Sense - get some Common Sense and use it. If you can't find any Common Sense, ask for help from somebody who has some Common Sense. Is Common Sense divine? Common Sense is the image of the Creator expressing revealed truth in my mind. - John W. (Kansas) __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] A congressional reform act for 2011
Nothing other than the fact that the sender made an error. No further comment or critique is necessary. -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Dave Sergeant Sent: Saturday, January 08, 2011 9:37 AM To: elecraft Reflector Subject: Re: [Elecraft] A congressional reform act for 2011 On 8 Jan 2011 at 10:03, Paul Gates wrote: > Congressional Reform Act of 2011 And what has this to do with Elecraft?... 73 Dave G3YMC http://www.davesergeant.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] A congressional reform act for 2011
On 8 Jan 2011 at 10:03, Paul Gates wrote: > Congressional Reform Act of 2011 And what has this to do with Elecraft?... 73 Dave G3YMC http://www.davesergeant.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] Fwd: A congressional reform act for 2011
-- Forwarded message -- From: Clayton Date: Sat, Jan 8, 2011 at 9:22 AMr\ Subject: A congressional reform act for 2011 To: Billy , Carolyn-Home , Carloyn-Work , Colt , Cyndi-Work , Dad , Danny-Jeep , Gwen G < florida.sunshi...@live.com>, James , Justin < jgates...@yahoo.com>, Levi , Mallory < mlgates1...@yahoo.com>, Mark-Jeep , Marla Kay < salsa_...@yahoo.com>, Mom , Richard-Jeep < richs...@yahoo.com>, Tiffany , Walt Congressional Reform Act of 2011 The 26th amendment (granting the right to vote for 18 year-olds) took only 3 months & 8 days to be ratified! Why? Simple! The people demanded it. That was in 1971...before computers, before e-mail, before cell phones, etc. Of the 27 amendments to the Constitution, seven (7) took 1 year or less to become the law of the land...all because of public pressure. I'm asking each addressee to forward this email to a minimum of twenty people on their address list; in turn ask each of those to do likewise. In three days, most people in The United States of America will have the message. This is one idea that really should be passed around. Congressional Reform Act of 2011 1. Term Limits. 12 years only, one of the possible options below.. A. Two Six-year Senate terms B. Six Two-year House terms C. One Six-year Senate term and three Two-Year House terms 2. No Tenure / No Pension. A Congressman collects a salary while in office and receives no pay when they are out of office. 3. Congress (past, present & future) participates in Social Security. All funds in the Congressional retirement fund move to the Social Security system immediately. All future funds flow into the Social Security system, and Congress participates with the American people. 4. Congress can purchase their own retirement plan, just as all Americans do. 5. Congress will no longer vote themselves a pay raise. Congressional pay will rise by the lower of CPI or 3%. 6. Congress loses their current health care system and participates in the same health care system as the American people. 7. Congress must equally abide by all laws they impose on the American people. 8. All contracts with past and present Congressmen are void effective 1/1/11. The American people did not make this contract with Congressmen. Congressmen made all these contracts for themselves. Serving in Congress is an honor, not a career. The Founding Fathers envisioned citizen legislators, so ours should serve their term(s), then go home and back to work. If each person contacts a minimum of twenty people then it will only take three days for most people (in the U.S.. ) to receive the message. Maybe it is time. THIS IS HOW YOU FIX CONGRESS! If you agree with the above, pass it on. If not, just delete You are one of my 20+. Please keep it going. = -- Paul, KD3JF Glen Burnie, MD __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] Err 12v
I recently had Q6 on the LPA board fail shorted, in which case you will get no power out at all. It's a MOSFET and very prone to an ESD event since it is on the antenna. Check gate-to-source resistance with an ohm meter. Should be 800 or so ohms. 73 N7RT - Original Message - From: "Randy Moore" To: "Elecraft Discussion List" Sent: Friday, January 07, 2011 7:45 PM Subject: [Elecraft] [K3] Err 12v >I am working on an friends K3 (#4446), recently purchased used. When I > got it, Power-On resulted in "ERR DSE." Firmware load failed, so I did > EEINIT, and then the firmware (4.22) loaded correctly. After going > through filter setups to match the on-board filters, things seemed to be > working correctly. But then I tried to increase power beyond 12w, and > now I get the "ERR 12V", which my friend had seen before. When that > error occurs, the KPA3 fans come on. The manual says to reset the > circuit breaker, but it wasn't tripped. Just for kicks, I tried to do > the Tx Gain Calibration through the K3 Utility (dummy load attached), > and even at the 5w level, it fails. > > I need some advice on how to proceed. > > Tnx es 73, > Randy, KS4L > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3: Hears stations twice
Correction: The PA station was running a Kenwood TS-570. His spur was down frequency about 400Hz. I have also head spurs from SGC 2020's and TenTec Paragons both caused by low PS voltage. Steve N4LQ - Original Message - From: "Steve Ellington" To: "OE5CSP-Chris" ; Sent: Saturday, January 08, 2011 9:06 AM Subject: Re: [Elecraft] K3: Hears stations twice > I've heard the same thing but with many other receivers. It usually turns > out that the transmitting station has a problem though. Low power supply > voltage is a common cause of transmitted spurs. I know one guy in PA > (state) > who has a TS-450 with a spur down about 200Hz, weak but strong enough to > be > heard 600 miles away. I've told him about it several times but he says he > has no idea what to do about it and continues to broadcast "CW Stereo". > > Steve > N4LQ > - Original Message - > From: "OE5CSP-Chris" > To: > Sent: Saturday, January 08, 2011 5:29 AM > Subject: Re: [Elecraft] K3: Hears stations twice > > >> >> Hi, >> >> During the Christmas holidays I spent a lot of time on 80m and I came >> across >> the problem mentioned on the reflector some time ago.Sometimes I can hear >> a >> strong station twice.Yesterday,for example I heard a strong German >> station >> on 3514 and a few khz down I heard the same signal again, but much >> weaker.I >> did not use the NB or NR. This happened a few times already.Is this a >> known >> issue and will it be fixed in the next firmware release? >> >> 73,Chris-OE5CSP >> -- >> View this message in context: >> http://elecraft.365791.n2.nabble.com/K3-Hears-stations-twice-tp5865819p5902107.html >> Sent from the [K3] mailing list archive at Nabble.com. >> __ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3: Hears stations twice
I've heard the same thing but with many other receivers. It usually turns out that the transmitting station has a problem though. Low power supply voltage is a common cause of transmitted spurs. I know one guy in PA (state) who has a TS-450 with a spur down about 200Hz, weak but strong enough to be heard 600 miles away. I've told him about it several times but he says he has no idea what to do about it and continues to broadcast "CW Stereo". Steve N4LQ - Original Message - From: "OE5CSP-Chris" To: Sent: Saturday, January 08, 2011 5:29 AM Subject: Re: [Elecraft] K3: Hears stations twice > > Hi, > > During the Christmas holidays I spent a lot of time on 80m and I came > across > the problem mentioned on the reflector some time ago.Sometimes I can hear > a > strong station twice.Yesterday,for example I heard a strong German station > on 3514 and a few khz down I heard the same signal again, but much > weaker.I > did not use the NB or NR. This happened a few times already.Is this a > known > issue and will it be fixed in the next firmware release? > > 73,Chris-OE5CSP > -- > View this message in context: > http://elecraft.365791.n2.nabble.com/K3-Hears-stations-twice-tp5865819p5902107.html > Sent from the [K3] mailing list archive at Nabble.com. > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] UK Elecraft Net
Hi all, After a short break for the festive period, I will be starting the net again tomorrow (Sunday) 9th January 2011 at 09:00z. It would be great to hear you all again :) As I missed the frequency on the first one I am sending it again :) 3658 +/- QRM 73 Ian -- Ian J Maude, G0VGS SysOp GB7MBC & HB9DRV-9 DX Clusters Member RSGB, GQRP 9838, FISTS 14077 | K3 #455 http://www.m0scg.org.uk __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] UK Elecraft Net
Hi all, After a short break for the festive period, I will be starting the net again tomorrow (Sunday) 9th January 2011 at 09:00z. It would be great to hear you all again :) 73 Ian -- Ian J Maude, G0VGS SysOp GB7MBC & HB9DRV-9 DX Clusters Member RSGB, GQRP 9838, FISTS 14077 | K3 #455 http://www.m0scg.org.uk __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] UK Elecraft Net
Hi all, After a short break for the festive period, I will be starting the net again tomorrow (Sunday) 9th January 2011 at 09:00z. It would be great to hear you all again :) 73 Ian -- Ian J Maude, G0VGS SysOp GB7MBC & HB9DRV-9 DX Clusters Member RSGB, GQRP 9838, FISTS 14077 | K3 #455 http://www.m0scg.org.uk __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3: Hears stations twice
Hi, During the Christmas holidays I spent a lot of time on 80m and I came across the problem mentioned on the reflector some time ago.Sometimes I can hear a strong station twice.Yesterday,for example I heard a strong German station on 3514 and a few khz down I heard the same signal again, but much weaker.I did not use the NB or NR. This happened a few times already.Is this a known issue and will it be fixed in the next firmware release? 73,Chris-OE5CSP -- View this message in context: http://elecraft.365791.n2.nabble.com/K3-Hears-stations-twice-tp5865819p5902107.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html