Re: [Elecraft] KX3 antenna question: Using 'remote' groundplane and random wire

[Jim Brown]

On 8/26/2012 5:34 PM, Andrew Moore wrote:
> Essentially what I want to do is to run the signal from the shack out to
> the trailer and have the radiator and ground plane "start" (and split off)
> there.  However, I'll definitely need the tuner in this scenario, so will
> having the tuner be located 100 feet before the split throw it all off, or
> introduce imbalances along, say, a coax run from the shack to the trailer?

The coax WILL add some loss, and how much loss will depend both on the 
coax and on the degree of mismatch. HOWEVER -- the additional loss due 
to mismatch is often much less than many believe. There's an excellent 
graph in the ARRL Handbook that shows this.

Some suggestions. First, ALWAYS use BIG coax to minimize the loss. You 
don't need a premium coax -- a decent RG8 with a robust copper braid 
shield is fine. Second, for both uses of the antenna, I would run coax 
from the rig to the aluminum frame at the point of connection, and make 
the shield the connection between the rig and the frame. Then simply put 
in a decent coax switch to change between the two operating positions.

Third, once the coax to the house is hooked up, check the VSWR without 
the antenna tuner, then use the graphs in the Handbook to first 
translate the VSWR reading in the shack to the actual VSWR at the 
antenna, then use that value of VSWR to see how much additional power is 
lost due to the mismatch.  If the loss is particularly high on any band 
due to a really bad match, tweak the length of the antenna to improve 
it.  Most really bad matches with a long wire are caused by an antenna 
that is very close to an exact multiple of half-wavelengths, or by a 
dipole that is very close to an exact multiple of a wavelength.  That's 
where the 44 ft vertical came from.

73, Jim K9YC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Bzzzzzzzzzzz from my K3

[Greg]

George,  is the speaker plugged in with a mono connector and the spkrs menu
item set to "2"?  If so you may have blown one of the speaker amp chips on
the dsp board.

73
Greg
 On Aug 26, 2012 9:24 PM,  wrote:

>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3FF Budd Dipole

[Dave AA7EE]

Fred - I think Jeff was referring to how the name Buddipole was conceived, as
opposed to how it's pronounced.  Bud-dipole makes a lot of sense, and I too
had never thought of that.

If that is what you meant Jeff, thanks for the enlightenment. My Buddipole
has given me years of good service. It is currently configured as a
quarter-wave vertical on the MURS band for talking to my non-licensed friend
down the street, so I guess it's not currently in ham service. Still works a
treat though!

Dave
AA7EE



--
View this message in context: 
http://elecraft.365791.n2.nabble.com/K3FF-Budd-Dipole-tp7561644p7561660.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Bzzzzzzzzzzz from my K3

[george]

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] Elecraft SSB Net results (8/26/12)

[Phillip Shepard]

We had a fine net today with good propagation.  We had 31 participants over
a 22 minute period. Discussions were on the KX3 speaker grill. Have a great
week.

Here is the list of participants.

Station NameQTH Rig S/N

N1LQDaveMA  K3  371
KD0HII  Brian   IA  K3  3672
K7BRR   BillAZ  K3  5545
K4QETonyNC  K3  6478
K4GCJ   Gerry   NC  K3  1597
W4PFM   PaulVA  K3  1673
WW4JF   JohnTN  K3  6185
W8CZN   Jim OH  K3  1224
AL7CE   Terry   AK  K3  5137
KY2DJim NJ  KX3 1291
KM4IK   Ian GA  K3  281
KF5IMA  Bruce   MS  K2  3575
W7GOTonyNV  KX3 117
WV5IDwayne  TX  K3  5287
W5TTF   Charlie TX  K3  4016
N8SBE   DaveMI  K3  3104
K2UTBob NJ  KX3 1418
NK6ADon CA  KX3 1247
NJ6LNealKY  K3  4601
K8JDC   DaveOH  K3  6332
KC5RY   George  TX  K3  5208
K8DJC   Nelson  OH  K3  560
KA0NCR  Arnie   NE  K3  185
KL7UW   Ed  AK  K3  4340
WA5BDU  NickAR  K3  1195
NA6ZDon CA  K3  5495
KC9WMR  Al  WI  TS450
W6ODJ   Oliver  CA  K3  1741
WC7SDaleWY  K2  6669
W0SZSteve   CO  K3  176
NS7PPhilOR  K3  1826

73,

Phil, NS7P
ph...@riousa.com
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] test

[K2GN]

test

Larry/K2GN - http://k2gn.com


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] rf gain

[Stan Gibbs]

Yes, Don, an EE INIT is not something one should do "arbitrarily".  It did
fix a similar non-linear RF gain problem of that myself and others reported
on this reflector back in 2010, so I suggested it as a solution.

The process in the owners manual makes clear that a saved configuration is a
very important step if one does not want to undertake a lot of parameter
setting and calibration.

As to running the RF gain calibration, this did not solve the non-linearity
for me, but the EE INIT did.





-
73, Stan - KR7C
--
View this message in context: 
http://elecraft.365791.n2.nabble.com/rf-gain-tp7561676p7561696.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] [K3] Problem w/front panel switches

[Fred Jensen]

Well Phil's problem isn't mine, and I'm not even sure I have a problem, 
but my K3 switches are a bit erratic.  They don't do things other than 
what they should do, they just don't always do it reliably.  Going to TX 
TEST, I'll often get a mode switch as if I tapped it instead.  Others 
are sort of the same.

I have a hard time keeping the radio stable on the shelf, it really 
isn't all that good for protection against gravity outages [like an 
SX-28 was :-)], and it does move.  I think I need to figure out how to 
get it really stable first.  Then we'll see.

73,

Fred K6DGW
- Northern California Contest Club
- CU in the 2012 Cal QSO Party 6-7 Oct 2012
- www.cqp.org

On 8/26/2012 9:39 AM, David Pratt wrote:
> Phil - Have you tried re-installing the Front Panel firmware?  Just a
> thought.
>
> 73 de David G4DMP
>
> In a recent message, Phil & Debbie Salas  writes
>> BTW - I can switch bands using the buttons on my KPA500, and it transmits
>> fine.  Just front panel button problems.


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Bzzzzzzzzzzz from my K3

[george]

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KX3 antenna question: Using 'remote' groundplane and random wire

[Don Wilhelm]

Andrew,

I would suggest that you take your KX3 to the aluminum skinned trailer 
and tune you antennas on all band segments.  The take you KX3 with KXAT3 
into the house shack and do it all over again.  The 100 foot of coax 
will make a difference in the tuning.

If all goes well, problem will be resolved and you can use either of the 
Elecraft rigs with no problem.

73,
  Don W3FPR


On 8/26/2012 8:34 PM, Andrew Moore wrote:
> Forgive me for what may be a silly question, but I've looked through the
> ARRL handbook, done the google searches, etc. and haven't found a solution.
>
> At the risk of starting a thread that may be more suitable for an antenna
> forum, I'm asking the Elecraft list in hopes that the KX3, KX1 and K1 users
> may have had experience here.
>
> I've got two main operating positions: One in an aluminum-skinned trailer
> which goes camping, and one in my shack with said trailer parked in the
> yard.
>

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] Bzzzzzzzzzzz from my K3

[William Jaker]

While attempting to set the vox /antivox /speaker / headphone settings on my 
K3-100 (#2389) - and during a moment when I was not touching the rig - I heard 
a pop on the audio and then a loud b noise which has not let up. At the 
time I was using an external speaker but disconnected it and the noise 
continued through the internal speaker. I cannot turn down the noise when I 
rotate the AF or RF knobs, though in the extreme counter-clockwise position it 
does change pitch.




The receiver seems to still be working properly, though the noise covers and 
distorts weak signals. Audio also sounds ok through headphones, though with 
that continuous bz right in front of me it's not easy listening. The rig 
also seems to work well on transmit although other operators tell me they also 
hear the b. It is there in all modes, and takes a couple of seconds to 
start up when I turn the rig on. Needless to say, I don't like running the K3 
while there's an obvious defect. I hope I haven't fried another DSP board. Any 
ideas about what my problem might be?
Thanks very much & 73,

Bill Jaker, WB8RAETown of Maine, NY




===
Email scanned by PC Tools - No viruses or spyware found.
(Email Guard: 9.0.0.898, Virus/Spyware Database: 6.20480)
http://www.pctools.com/
===
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K144XV

[Lyle Johnson]

Download the K3 Schematics from the manuals section of the Elecraft 
website. The K144XV schematic is included in that PDF file.

73,

Lyle KK7P

>   ... Where can I get a schematic of the module?

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] K144XV

[k7ca]

 

Hello, 

 I got a K3 kit in April which included the K144XV. It went
together fine and had about 10 watts output on 2M. I made a few FM
contacts and a couple of SSB contacts, the last one in the June VHF
contest. I tried 2m again this month and noticed the power output only
about .5 watt max. The K144XV utility in the command tester shows P006
with key up and P011 in key down. The T command shows T76C key up and
T32C key down. Current is about 1.25A key up and 2.5A key down. Any
ideas as to what might have happened? I checked the coax from the the 2m
module to the output connector on the K3 and it is fine. Where can I get
a schematic of the module? Thanks, Al K7CA 
 
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KX3 antenna question: Using 'remote' groundplane andrandom wire

[Mike WA8BXN]

Hi Andrew, 
 
The best solution is to put a tuner in the trailer that automatically tunes
when it senses RF and a high SWR. Several manufacturers make such tuners.
Connecting the random wire to 100 feet of coax and then having the tuner in
your rig do the tuning will result in high SWR in the coax and a lot of loss
 
 
It would be better if you can't add a remote tuner to not use the trailer as
a ground and run your random wire into the shack and provide the best ground
system you can there. 
 
BTW, this is probably a question that will be of interest to many others, so
I am posting to the reflector. 
73 - Mike WA8BXN 
 
 
 
 
---Original Message--- 
 
From: Andrew Moore 
Date: 8/26/2012 8:37:43 PM 
To: Elecraft 
Subject: [Elecraft] KX3 antenna question: Using 'remote' groundplane
andrandom wire 
 
Forgive me for what may be a silly question, but I've looked through the 
ARRL handbook, done the Google searches, etc. And haven't found a solution. 
 
At the risk of starting a thread that may be more suitable for an antenna 
Forum, I'm asking the Elecraft list in hopes that the KX3, KX1 and K1 users 
May have had experience here. 
 
I've got two main operating positions: One in an aluminum-skinned trailer 
Which goes camping, and one in my shack with said trailer parked in the 
Yard. 
 
For the camping scenario, for ease of use and simplicity, the KX3 sits 
Inside the trailer with its built-in antenna tuner's ground connected to 
The shell of the trailer, and the hot side going to the random-length wire 
Tossed into the trees. Works great. 
 
For when I'm home in the shack, I'd like to take advantage of the trailer's 
Metal shell as a ground plane or counterpoise for a random-length wire, 
Which could be either the same one from the trailer, or a second one in the 
Trees. 
 
However, most of the random-length antenna solutions I've seen have 
Involved having the ground plane (or counterpoise) located at the tuner 
Itself, which in the case of the KX3 means at the KX3 itself, in the shack, 
About 100 feet from the trailer. 
 
Essentially what I want to do is to run the signal from the shack out to 
The trailer and have the radiator and ground plane "start" (and split off) 
There. However, I'll definitely need the tuner in this scenario, so will 
Having the tuner be located 100 feet before the split throw it all off, or 
Introduce imbalances along, say, a coax run from the shack to the trailer? 
 
I get the sense this may be a very basic question but I admit I'm no 
Antenna expert so I'm asking the gurus. 
 
To keep the noise level down, direct replies may be best, and I'll be glad 
To summarize to the group if there's interest. 
 
Thanks, 
--Andrew, NV1B 
Maineware.net
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] K2/10 for sale

[Bill Tubbs]

I have a nicely completed K2, SN# 656, 10 watts, for sale. 

I'm the second owner (bought this back in March) and the original builder did a 
great job on it. All I've done since buying it is add the KBT2 internal battery 
kit. The previous owner also installed a Yaesu main tuning knob which I wasn't 
aware of until recently because I've never seen another K2 up close.

It also has a Ten Tec handheld mike wired for it. 

It has:

KSB2 SSB
K160RX 160M
KNB2 NB
KAT2 ATU
KAF2 audio filter
KBT2 battery kit

I also have, but have not installed, all of the upgrades to make it current. 
This would give you a little of the "kit experience" when you install all of 
these. Looks like a new kit would run about $1400-1500 on the Elecraft ordering 
page. I would sell it all for $1000.

Thanks for reading!

73,
Bill
WK6A
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KX3: No RX - SWR 25 to 1

[Matt Zilmer]

Hi Fred,

To pin this down a bit further, maybe you could try an experiment.  

1.  Set the KX3's RX ISO to OFF.  This is a MENU function.
2.  Put the KX3 on a freq on 40m.  Leave it on RX.
3.  Put the "main station" on the same 40m freq.
4.  Note if your main receiver can hear the KX3's LO (should be able
to hear carrier if RX ISO is OFF).  You may need to offset the
receiver's carrier frequency a little to hear the carrier from the
KX3's LO.
5.  If #4 is no, you may be correct.  The synth isn't producing any
injection frequency.  It's a good idea to have some type of antenna,
even a short piece of wire, so that the KX3 radiates just a little
energy that the other receiver can copy.

Just an idea

Good luck, but with Elecraft support you won't need it...

73,
matt W6NIA


On Sun, 26 Aug 2012 19:50:27 -0300, you wrote:

>Matt, thanks I will do that tmrw. However if I had any trouble with any
>circuit behind the receiver I still would be able to hear my transmission
>using my main station. The KX3 is seating besides it. It does not hear
>anything.
>If it was an analog equipment one could say that the local oscillator stop
>oscillating.
>If no one reported this kind of problem in this list, I will inquire
>Elecraft.
>
>Fred
>
>2012/8/26 Matt Zilmer 
>
>> If the NR4C suggestion doesn't solve your problem, physically remove
>> the ATU and recheck if you have this problem.  If the problem is with
>> the ATU, this will clear it up.  Of course, you should get the ATU
>> replaced on warranty
>>
>> Don't forget to reconnect the BNC internal conductor to the RF board's
>> antenna connector.
>>
>> 73,
>> matt W6NIA
>> KX3 #6 F/T
>>
>>
>> On Sun, 26 Aug 2012 18:05:26 -0400, you wrote:
>>
>> >Open it up and check to make sure the BNC connector is plugged into the
>> ATU.
>> >It sounds like the antenna is not connected, you did check this, didn't
>> you?
>> >
>> >...bc  nr4c
>> >
>> >-Original Message-
>> >From: Fred Carvalho [mailto:fred.py...@gmail.com]
>> >Sent: Sunday, August 26, 2012 5:31 PM
>> >To: elecraft@mailman.qth.net
>> >Subject: [Elecraft] KX3: No RX - SWR 25 to 1
>> >
>> >Hello guys
>> >Need some help to start with.
>> >
>> >I have a KX3 purchased in May. It has the roofing filter and the ATU unit.
>> >I have not updated the firmware yet. Still with the one loaded in the
>> >factory.
>> >Recently the radio went mute. Also when trying to match the antenna with
>> >the ATU, SWR displayed 25:1.
>> >It did that sometimes sometimes. Each time it went back to normal.  Then
>> >went mute definitely.
>> >I have bypassed the ATU via the Menu, no change.
>> >I have also verified if when mute it was insensitive, but receiving. No
>> >receiving at all.
>> >
>> >Any ideas to start with ? Thanks
>> >
>> >--
>> >Fred C Carvalho - PY2XB
>> >T30PY & T30SIX Coming in October
>> >Support this DXpedition : http://www.mdxc.org/t30py/
>> >[image: T30PY-3D.png]
>>
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] KX3 antenna question: Using 'remote' groundplane and random wire

[Andrew Moore]

Forgive me for what may be a silly question, but I've looked through the
ARRL handbook, done the google searches, etc. and haven't found a solution.

At the risk of starting a thread that may be more suitable for an antenna
forum, I'm asking the Elecraft list in hopes that the KX3, KX1 and K1 users
may have had experience here.

I've got two main operating positions: One in an aluminum-skinned trailer
which goes camping, and one in my shack with said trailer parked in the
yard.

For the camping scenario, for ease of use and simplicity, the KX3 sits
inside the trailer with its built-in antenna tuner's ground connected to
the shell of the trailer, and the hot side going to the random-length wire
tossed into the trees. Works great.

For when I'm home in the shack, I'd like to take advantage of the trailer's
metal shell as a ground plane or counterpoise for a random-length wire,
which could be either the same one from the trailer, or a second one in the
trees.

However, most of the random-length antenna solutions I've seen have
involved having the ground plane (or counterpoise) located at the tuner
itself, which in the case of the KX3 means at the KX3 itself, in the shack,
about 100 feet from the trailer.

Essentially what I want to do is to run the signal from the shack out to
the trailer and have the radiator and ground plane "start" (and split off)
there.  However, I'll definitely need the tuner in this scenario, so will
having the tuner be located 100 feet before the split throw it all off, or
introduce imbalances along, say, a coax run from the shack to the trailer?

I get the sense this may be a very basic question but I admit I'm no
antenna expert so I'm asking the gurus.

To keep the noise level down, direct replies may be best, and I'll be glad
to summarize to the group if there's interest.

Thanks,
--Andrew, NV1B
maineware.net
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] rf gain

[Mike K2MK]

Hi Terry,

Try running the RF Gain calibration from the K3 Utility Program.

73,
Mike K2MK


terry220 wrote
> 
> hi
> i have just received my k3 from waters&stanton here in the uk.i have a
> slight problem
> with the rf gain on receive if you turn the rf gain contril fully
> clockwise the signal goes
> in negative mode instead of peeking it goes in reverse.it peeks when
> control is set to 
> about 12 o"clock strange is there an easy fix for this
> 




--
View this message in context: 
http://elecraft.365791.n2.nabble.com/rf-gain-tp7561676p7561685.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KX3: No RX - SWR 25 to 1

[vk4tux]

I would be checking the dc resistance of the the 50 ohm output > bnc back
through, as it sounds more 
like a short than an open circuit. 

Quite often an open will only attenuate a rx signal rather than silence it
altogether as a short will do.

Adrian ... vk4tux



--
View this message in context: 
http://elecraft.365791.n2.nabble.com/KX3-No-RX-SWR-25-to-1-tp7561671p7561684.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] rf gain

[Don Wilhelm]

I would discourage one from arbitrarily doing an EEINIT" unless you have 
a stored K3 configuration file that you can load afterward.

EEINIT sets all menu items back to the default settings.  It may be 
necessary, but do know that you will have a lot of calibration to do 
unless you have that configuration file with the settings from a known 
good working time for your K3 (goes for KX3 too).

73,
Don W3FPR
.
On 8/26/2012 7:46 PM, Stan Gibbs wrote:
> Try running the parameter initialization process, following the instructions
> on page 66 of the latest owners manual.  My K3 had this behavior at one time
> and it was corrected by running EE INIT.
>
>

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] rf gain

[Stan Gibbs]

Try running the parameter initialization process, following the instructions
on page 66 of the latest owners manual.  My K3 had this behavior at one time
and it was corrected by running EE INIT.




-
73, Stan - KR7C
--
View this message in context: 
http://elecraft.365791.n2.nabble.com/rf-gain-tp7561676p7561683.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] 4 States QRP Group special event announcement..

[Arnie Grubbs]

Today on the Elecraft ssb net I announced that the 4 States QRP group was going 
to have a special event station on the air next weekend...   This was a mix up 
on my part..  the date for the event is Sept 8 and 9th.

Please see the groups web page at. 4sqrp.com

There will be at least 2 KX3s and possibly a few other Elecraft rigs on the air 
for the " Big Brutus " event,  with the call of K0B.

We will be operating as the band condtions allow, around the "qrp" freqs and 
also the hf pack freqs.   Look for cw and some ssb signals, and maybe even psk.

73 and I hope to see you in our logs!

Arnie. KA0NCR

.

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KX3: No RX - SWR 25 to 1

[Don Wilhelm]

Fred,

Please also be suspicious of the coax, the BNC connector and your antenna.

Can you receive well with that same BNC connector plugged into another 
radio?  Substitution is the quickest troubleshooting tool in cases like 
this one.

73,
Don W3FPR

On 8/26/2012 6:13 PM, Fred Carvalho wrote:
> Hi Bc, yes I did. As I mentioned there is no RX at all, even with my main
> station on the air , close by to the KX3.
> Fred
>
>

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KX3: No RX - SWR 25 to 1

[Fred Carvalho]

Matt, thanks I will do that tmrw. However if I had any trouble with any
circuit behind the receiver I still would be able to hear my transmission
using my main station. The KX3 is seating besides it. It does not hear
anything.
If it was an analog equipment one could say that the local oscillator stop
oscillating.
If no one reported this kind of problem in this list, I will inquire
Elecraft.

Fred

2012/8/26 Matt Zilmer 

> If the NR4C suggestion doesn't solve your problem, physically remove
> the ATU and recheck if you have this problem.  If the problem is with
> the ATU, this will clear it up.  Of course, you should get the ATU
> replaced on warranty
>
> Don't forget to reconnect the BNC internal conductor to the RF board's
> antenna connector.
>
> 73,
> matt W6NIA
> KX3 #6 F/T
>
>
> On Sun, 26 Aug 2012 18:05:26 -0400, you wrote:
>
> >Open it up and check to make sure the BNC connector is plugged into the
> ATU.
> >It sounds like the antenna is not connected, you did check this, didn't
> you?
> >
> >...bc  nr4c
> >
> >-Original Message-
> >From: Fred Carvalho [mailto:fred.py...@gmail.com]
> >Sent: Sunday, August 26, 2012 5:31 PM
> >To: elecraft@mailman.qth.net
> >Subject: [Elecraft] KX3: No RX - SWR 25 to 1
> >
> >Hello guys
> >Need some help to start with.
> >
> >I have a KX3 purchased in May. It has the roofing filter and the ATU unit.
> >I have not updated the firmware yet. Still with the one loaded in the
> >factory.
> >Recently the radio went mute. Also when trying to match the antenna with
> >the ATU, SWR displayed 25:1.
> >It did that sometimes sometimes. Each time it went back to normal.  Then
> >went mute definitely.
> >I have bypassed the ATU via the Menu, no change.
> >I have also verified if when mute it was insensitive, but receiving. No
> >receiving at all.
> >
> >Any ideas to start with ? Thanks
> >
> >--
> >Fred C Carvalho - PY2XB
> >T30PY & T30SIX Coming in October
> >Support this DXpedition : http://www.mdxc.org/t30py/
> >[image: T30PY-3D.png]
>



-- 
Fred C Carvalho - PY2XB
T30PY & T30SIX Coming in October
Support this DXpedition : http://www.mdxc.org/t30py/
[image: T30PY-3D.png]
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KX3: No RX - SWR 25 to 1

[Matt Zilmer]

If the NR4C suggestion doesn't solve your problem, physically remove
the ATU and recheck if you have this problem.  If the problem is with
the ATU, this will clear it up.  Of course, you should get the ATU
replaced on warranty

Don't forget to reconnect the BNC internal conductor to the RF board's
antenna connector.

73,
matt W6NIA
KX3 #6 F/T


On Sun, 26 Aug 2012 18:05:26 -0400, you wrote:

>Open it up and check to make sure the BNC connector is plugged into the ATU.
>It sounds like the antenna is not connected, you did check this, didn't you?
>
>...bc  nr4c
>
>-Original Message-
>From: Fred Carvalho [mailto:fred.py...@gmail.com] 
>Sent: Sunday, August 26, 2012 5:31 PM
>To: elecraft@mailman.qth.net
>Subject: [Elecraft] KX3: No RX - SWR 25 to 1
>
>Hello guys
>Need some help to start with.
>
>I have a KX3 purchased in May. It has the roofing filter and the ATU unit.
>I have not updated the firmware yet. Still with the one loaded in the
>factory.
>Recently the radio went mute. Also when trying to match the antenna with
>the ATU, SWR displayed 25:1.
>It did that sometimes sometimes. Each time it went back to normal.  Then
>went mute definitely.
>I have bypassed the ATU via the Menu, no change.
>I have also verified if when mute it was insensitive, but receiving. No
>receiving at all.
>
>Any ideas to start with ? Thanks
>
>-- 
>Fred C Carvalho - PY2XB
>T30PY & T30SIX Coming in October
>Support this DXpedition : http://www.mdxc.org/t30py/
>[image: T30PY-3D.png]
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KX3: No RX - SWR 25 to 1

[Fred Carvalho]

Bill,  no smeter readings, no reception of strong nearby signals, 25:1 SWR.
Speaker works and has a normal "floor" receiver sound.

2012/8/26 Bill Conkling 

>  OK
>
> ** **
>
> Unplug all cables except the antenna, turn up volume,   Still nothing?
> 
>
> ** **
>
> Do you see any action on "S-meter"?
>
> ** **
>
> Is speaker plugged in to main board?
>
> ** **
>
> ...bc  nr4c
>
> ** **
>  --
>
> *From:* Fred Carvalho [mailto:fred.py...@gmail.com]
> *Sent:* Sunday, August 26, 2012 6:14 PM
> *To:* Bill Conkling
> *Cc:* elecraft@mailman.qth.net
> *Subject:* Re: [Elecraft] KX3: No RX - SWR 25 to 1
>
> ** **
>
> Hi Bc, yes I did. As I mentioned there is no RX at all, even with my main
> station on the air , close by to the KX3.
>
> Fred
>
> 2012/8/26 Bill Conkling 
>
> Open it up and check to make sure the BNC connector is plugged into the
> ATU.
> It sounds like the antenna is not connected, you did check this, didn't
> you?
>
> ...bc  nr4c
>
>
> -Original Message-
> From: Fred Carvalho [mailto:fred.py...@gmail.com]
> Sent: Sunday, August 26, 2012 5:31 PM
> To: elecraft@mailman.qth.net
> Subject: [Elecraft] KX3: No RX - SWR 25 to 1
>
> Hello guys
> Need some help to start with.
>
> I have a KX3 purchased in May. It has the roofing filter and the ATU unit.
> I have not updated the firmware yet. Still with the one loaded in the
> factory.
> Recently the radio went mute. Also when trying to match the antenna with
> the ATU, SWR displayed 25:1.
> It did that sometimes sometimes. Each time it went back to normal.  Then
> went mute definitely.
> I have bypassed the ATU via the Menu, no change.
> I have also verified if when mute it was insensitive, but receiving. No
> receiving at all.
>
> Any ideas to start with ? Thanks
>
> --
> Fred C Carvalho - PY2XB
> T30PY & T30SIX Coming in October
> Support this DXpedition : http://www.mdxc.org/t30py/
> [image: T30PY-3D.png]
>
>
>
>
> --
> Fred C Carvalho - PY2XB
> T30PY & T30SIX Coming in October
> Support this DXpedition : http://www.mdxc.org/t30py/
> [image: T30PY-3D.png]
>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
>
>
> 
>
> ** **
>
> --
> Fred C Carvalho - PY2XB
>
> T30PY & T30SIX Coming in October  
>
> Support this DXpedition : http://www.mdxc.org/t30py/
>
> [image: T30PY-3D.png]
>
> ** **
>



-- 
Fred C Carvalho - PY2XB
T30PY & T30SIX Coming in October
Support this DXpedition : http://www.mdxc.org/t30py/
[image: T30PY-3D.png]
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Problem solved W2 power reading not functioning

[Ron D'Eau Claire]

Good news Don.

Some of those adapters are pretty flakey with widely varying output voltages
and lots of ripple on the voltage, even those supplied for use with other
electronics. Sometimes the first thing inside the electronic unit being
powered is a big filter capacitor or even a voltage regulator, while the W2
assumes a decently clean 13V supply. 

73, Ron AC7AC



-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of gold...@charter.net
Sent: Sunday, August 26, 2012 12:59 PM
To: iain macdonnell - N6ML
Cc: elecraft list
Subject: Re: [Elecraft] Problem solved W2 power reading not functioning

Ok I found the problem with the W2, or problems.

1) The interface cable or CAT5 cable apparently was bad.

2) Power if not coming from the radio apparently the unit is not happy, I
was using the AC adaptor from my MFJ analizer as I did not have a power
cable that would fit it ready to go.

Changed the two items above and it is now working, auto range and all.

So I figured I better share.

Thanks
Don

~73
Don
KD8NNU
FH#4107


On Sun, Aug 26, 2012 at 3:28 PM, iain macdonnell - N6ML wrote:

> It might be interesting to get the W2 Utility running, and see if you 
> get a forward power measurement on that. I sounds like it is actually 
> measuring forward power, as the range is automatically changing 
> (evidenced by "SWR" only showing below 20W, although it's not clear, 
> from your description, what you see with auto-ranging and higher than 
> 20W forward power) it seems to maybe suggest a problem with the 
> LED display...
>
> 73,
>
> ~iain / N6ML
>
>
> On Sun, Aug 26, 2012 at 12:07 PM,   wrote:
>>
>> HI Guys,
>>
>> I have a used W2 that has the 2kw transmitter that is not functioning 
>> properly.
>>
>> I can get it to read out swr on the led's if it is on the 20w range 
>> setting.  If I use auto it selects the 20w range and only measures 
>> swr.
>>
>> There is no outputs on the led's for the power other then the 1 led 
>> being lit.
>>
>> When trying to do a TX as long as I am at 20w or less the swr leds 
>> light but again no power led's light up.
>>
>> I have tried both the sensor 1 and sensor 2 ports but it does not 
>> make a difference.
>>
>> I has the 12v power on mod done by the previous owner.
>>
>> Anyway are there any ideas on what to look for or is this thing going 
>> to have to go to elecraft for repairs.
>>
>> Thanks
>> Don
>>
>> ~73
>> Don
>> KD8NNU
>> FH#4107
>> __
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft@mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net Please help support this 
>> email list: http://www.qsl.net/donate.html
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KX3: No RX - SWR 25 to 1

[Bill Conkling]

OK

 

Unplug all cables except the antenna, turn up volume,   Still nothing?

 

Do you see any action on "S-meter"?

 

Is speaker plugged in to main board?

 

...bc  nr4c

 

  _  

From: Fred Carvalho [mailto:fred.py...@gmail.com] 
Sent: Sunday, August 26, 2012 6:14 PM
To: Bill Conkling
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KX3: No RX - SWR 25 to 1

 

Hi Bc, yes I did. As I mentioned there is no RX at all, even with my main
station on the air , close by to the KX3.

Fred

2012/8/26 Bill Conkling 

Open it up and check to make sure the BNC connector is plugged into the ATU.
It sounds like the antenna is not connected, you did check this, didn't you?

...bc  nr4c


-Original Message-
From: Fred Carvalho [mailto:fred.py...@gmail.com]
Sent: Sunday, August 26, 2012 5:31 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] KX3: No RX - SWR 25 to 1

Hello guys
Need some help to start with.

I have a KX3 purchased in May. It has the roofing filter and the ATU unit.
I have not updated the firmware yet. Still with the one loaded in the
factory.
Recently the radio went mute. Also when trying to match the antenna with
the ATU, SWR displayed 25:1.
It did that sometimes sometimes. Each time it went back to normal.  Then
went mute definitely.
I have bypassed the ATU via the Menu, no change.
I have also verified if when mute it was insensitive, but receiving. No
receiving at all.

Any ideas to start with ? Thanks

--
Fred C Carvalho - PY2XB
T30PY & T30SIX Coming in October
Support this DXpedition : http://www.mdxc.org/t30py/
[image: T30PY-3D.png]




--
Fred C Carvalho - PY2XB
T30PY & T30SIX Coming in October
Support this DXpedition : http://www.mdxc.org/t30py/
[image: T30PY-3D.png]

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html





 

-- 
Fred C Carvalho - PY2XB

T30PY & T30SIX Coming in October  

Support this DXpedition : http://www.mdxc.org/t30py/

 T30PY-3D.png
 

 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KX3: No RX - SWR 25 to 1

[Fred Carvalho]

Hi Bc, yes I did. As I mentioned there is no RX at all, even with my main
station on the air , close by to the KX3.
Fred

2012/8/26 Bill Conkling 

> Open it up and check to make sure the BNC connector is plugged into the
> ATU.
> It sounds like the antenna is not connected, you did check this, didn't
> you?
>
> ...bc  nr4c
>
> -Original Message-
> From: Fred Carvalho [mailto:fred.py...@gmail.com]
> Sent: Sunday, August 26, 2012 5:31 PM
> To: elecraft@mailman.qth.net
> Subject: [Elecraft] KX3: No RX - SWR 25 to 1
>
> Hello guys
> Need some help to start with.
>
> I have a KX3 purchased in May. It has the roofing filter and the ATU unit.
> I have not updated the firmware yet. Still with the one loaded in the
> factory.
> Recently the radio went mute. Also when trying to match the antenna with
> the ATU, SWR displayed 25:1.
> It did that sometimes sometimes. Each time it went back to normal.  Then
> went mute definitely.
> I have bypassed the ATU via the Menu, no change.
> I have also verified if when mute it was insensitive, but receiving. No
> receiving at all.
>
> Any ideas to start with ? Thanks
>
> --
> Fred C Carvalho - PY2XB
> T30PY & T30SIX Coming in October
> Support this DXpedition : http://www.mdxc.org/t30py/
> [image: T30PY-3D.png]
>
>
>
>
> --
> Fred C Carvalho - PY2XB
> T30PY & T30SIX Coming in October
> Support this DXpedition : http://www.mdxc.org/t30py/
> [image: T30PY-3D.png]
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
>


-- 
Fred C Carvalho - PY2XB
T30PY & T30SIX Coming in October
Support this DXpedition : http://www.mdxc.org/t30py/
[image: T30PY-3D.png]
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KX3: No RX - SWR 25 to 1

[Bill Conkling]

Open it up and check to make sure the BNC connector is plugged into the ATU.
It sounds like the antenna is not connected, you did check this, didn't you?

...bc  nr4c

-Original Message-
From: Fred Carvalho [mailto:fred.py...@gmail.com] 
Sent: Sunday, August 26, 2012 5:31 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] KX3: No RX - SWR 25 to 1

Hello guys
Need some help to start with.

I have a KX3 purchased in May. It has the roofing filter and the ATU unit.
I have not updated the firmware yet. Still with the one loaded in the
factory.
Recently the radio went mute. Also when trying to match the antenna with
the ATU, SWR displayed 25:1.
It did that sometimes sometimes. Each time it went back to normal.  Then
went mute definitely.
I have bypassed the ATU via the Menu, no change.
I have also verified if when mute it was insensitive, but receiving. No
receiving at all.

Any ideas to start with ? Thanks

-- 
Fred C Carvalho - PY2XB
T30PY & T30SIX Coming in October
Support this DXpedition : http://www.mdxc.org/t30py/
[image: T30PY-3D.png]




-- 
Fred C Carvalho - PY2XB
T30PY & T30SIX Coming in October
Support this DXpedition : http://www.mdxc.org/t30py/
[image: T30PY-3D.png]
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Please unsubscribe me from the list. n7...@aol.com thank you

[Mike]

The unsubscribe link is at the bottom of every post. Just click the link 
labeled "Home:".

73, Mike NF4L

On 8/26/12 4:37 PM, William Painter wrote:
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] KX3: No RX - SWR 25 to 1

[Fred Carvalho]

Hello guys
Need some help to start with.

I have a KX3 purchased in May. It has the roofing filter and the ATU unit.
I have not updated the firmware yet. Still with the one loaded in the
factory.
Recently the radio went mute. Also when trying to match the antenna with
the ATU, SWR displayed 25:1.
It did that sometimes sometimes. Each time it went back to normal.  Then
went mute definitely.
I have bypassed the ATU via the Menu, no change.
I have also verified if when mute it was insensitive, but receiving. No
receiving at all.

Any ideas to start with ? Thanks

-- 
Fred C Carvalho - PY2XB
T30PY & T30SIX Coming in October
Support this DXpedition : http://www.mdxc.org/t30py/
[image: T30PY-3D.png]




-- 
Fred C Carvalho - PY2XB
T30PY & T30SIX Coming in October
Support this DXpedition : http://www.mdxc.org/t30py/
[image: T30PY-3D.png]
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] [K3] Problem w/front panel switches

[Jessie Oberreuter]

  I had the same experience several months back.  Tracing it down, I 
found that one of the encoder push-buttons had internally semi-shorted to 
ground.  Each front-panel switch essentially acts as a divider tap, so the 
semi-short ended up shifting the effective tap point of every other switch 
on the panel.  I snipped the offending switch lead, and all was fine.  As 
a CW op, having that knob permanently set to cw speed hasn't been an 
issue, but I do intend to send the rig in for a full replacement of all 
four switch/encoders as soon as my KX3 arrives :).  (When I contacted 
Elecraft for a replacement part, I was told that I should just have all 
four replaced, as the switch/encoders they are using now have a much nicer 
feel than the first gen ones used in my #286 K3, and I would notice the 
difference in feel between a single new part and the old ones.)


On Sun, 26 Aug 2012, Phil & Debbie Salas wrote:

> Well - Thought I'd put this out here since it'll be tomorrow before I can
> contact Elecraft Support.
>
> This morning my K3 (SN308) started having problems with the front panel
> controls.  I can't change bands with the BAND button, pressing the MODE
> button changes antennas, pressing the M>V button plays my M1 CW message,
> etc.  I re-loaded all firmware, and I pulled the front panel loose and
> dabbed some DeOxit on the connector (I've heard of problems with the tin
> plated pins which I have).  Anyway, no joy.  Anyone see anything familiar,
> and know of a solution?
>
> BTW - I can switch bands using the buttons on my KPA500, and it transmits
> fine.  Just front panel button problems.
>
> Thanks,
> Phil - AD5X
>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] W2 power reading not functioning

[Bill K9YEQ]

I had this happen to me once.  I reloaded the firmware and that fixed it.
Must've had some stray RF or something that caused the firmware to corrupt.

73,
Bill
K9YEQ


-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of gold...@charter.net
Sent: Sunday, August 26, 2012 2:07 PM
To: elecraft list
Subject: [Elecraft] W2 power reading not functioning


HI Guys,

I have a used W2 that has the 2kw transmitter that is not functioning
properly.

I can get it to read out swr on the led's if it is on the 20w range setting.
If I use auto it selects the 20w range and only measures swr.

There is no outputs on the led's for the power other then the 1 led being
lit.

When trying to do a TX as long as I am at 20w or less the swr leds light but
again no power led's light up.

I have tried both the sensor 1 and sensor 2 ports but it does not make a
difference.

I has the 12v power on mod done by the previous owner.

Anyway are there any ideas on what to look for or is this thing going to
have to go to elecraft for repairs.

Thanks
Don

~73
Don
KD8NNU
FH#4107
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 and the THP HL-1.5KFX

[Bill K9YEQ]

Peter,

I have the 2.5 and I use the cable supplied by the manufacturer.  It works
super, whether or not the THP is on or off.  I have had no issues.

73,
Bill
K9YEQ


-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Peter Chamalian
Sent: Sunday, August 26, 2012 8:07 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 and the THP HL-1.5KFX

Has anyone successfully interfaced a K3 and THP HL-1.5KFX amp so the K3
tells the amp what band to be on?  If so, I would appreciate specifics on
how you did it.

 

Thanks,

 

Pete, W1RM

 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] SOLD: Elecraft K3 Deluxe Weighted Tuning Knob Combo with Ball Bearing Finger Dimple

[David and Dianne on Comcast]

Thanks to all who inquired.

The knobs have been sold pending payment

73 de N1LQ-Dave
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] Please unsubscribe me from the list. n7...@aol.com thank you

[William Painter]

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] WTD P3/SVGA

[Mike Sanders]

Greetings, I would like to find an excellent P3 with
SVGA adapter. Anyone have one to part with? If
so details please. Thanks, Mike


Mike Sanders
KØAZ




__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Problem solved W2 power reading not functioning

[goldtr8]

Ok I found the problem with the W2, or problems.

1) The interface cable or CAT5 cable apparently was bad.

2) Power if not coming from the radio apparently the unit is not happy, 
I was using the AC adaptor from my MFJ analizer as I did not have a 
power cable that would fit it ready to go.

Changed the two items above and it is now working, auto range and all.

So I figured I better share.

Thanks
Don

~73
Don
KD8NNU
FH#4107


On Sun, Aug 26, 2012 at 3:28 PM, iain macdonnell - N6ML wrote:

> It might be interesting to get the W2 Utility running, and see if you
> get a forward power measurement on that. I sounds like it is actually
> measuring forward power, as the range is automatically changing
> (evidenced by "SWR" only showing below 20W, although it's not clear,
> from your description, what you see with auto-ranging and higher than
> 20W forward power) it seems to maybe suggest a problem with the
> LED display...
>
> 73,
>
> ~iain / N6ML
>
>
> On Sun, Aug 26, 2012 at 12:07 PM,   wrote:
>>
>> HI Guys,
>>
>> I have a used W2 that has the 2kw transmitter that is not functioning
>> properly.
>>
>> I can get it to read out swr on the led's if it is on the 20w range
>> setting.  If I use auto it selects the 20w range and only measures 
>> swr.
>>
>> There is no outputs on the led's for the power other then the 1 led
>> being lit.
>>
>> When trying to do a TX as long as I am at 20w or less the swr leds 
>> light
>> but again no power led's light up.
>>
>> I have tried both the sensor 1 and sensor 2 ports but it does not 
>> make a
>> difference.
>>
>> I has the 12v power on mod done by the previous owner.
>>
>> Anyway are there any ideas on what to look for or is this thing going 
>> to
>> have to go to elecraft for repairs.
>>
>> Thanks
>> Don
>>
>> ~73
>> Don
>> KD8NNU
>> FH#4107
>> __
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft@mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] W2 power reading not functioning

[iain macdonnell - N6ML]

It might be interesting to get the W2 Utility running, and see if you
get a forward power measurement on that. I sounds like it is actually
measuring forward power, as the range is automatically changing
(evidenced by "SWR" only showing below 20W, although it's not clear,
from your description, what you see with auto-ranging and higher than
20W forward power) it seems to maybe suggest a problem with the
LED display...

73,

~iain / N6ML


On Sun, Aug 26, 2012 at 12:07 PM,   wrote:
>
> HI Guys,
>
> I have a used W2 that has the 2kw transmitter that is not functioning
> properly.
>
> I can get it to read out swr on the led's if it is on the 20w range
> setting.  If I use auto it selects the 20w range and only measures swr.
>
> There is no outputs on the led's for the power other then the 1 led
> being lit.
>
> When trying to do a TX as long as I am at 20w or less the swr leds light
> but again no power led's light up.
>
> I have tried both the sensor 1 and sensor 2 ports but it does not make a
> difference.
>
> I has the 12v power on mod done by the previous owner.
>
> Anyway are there any ideas on what to look for or is this thing going to
> have to go to elecraft for repairs.
>
> Thanks
> Don
>
> ~73
> Don
> KD8NNU
> FH#4107
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] W2 power reading not functioning

[goldtr8]

HI Guys,

I have a used W2 that has the 2kw transmitter that is not functioning 
properly.

I can get it to read out swr on the led's if it is on the 20w range 
setting.  If I use auto it selects the 20w range and only measures swr.

There is no outputs on the led's for the power other then the 1 led 
being lit.

When trying to do a TX as long as I am at 20w or less the swr leds light 
but again no power led's light up.

I have tried both the sensor 1 and sensor 2 ports but it does not make a 
difference.

I has the 12v power on mod done by the previous owner.

Anyway are there any ideas on what to look for or is this thing going to 
have to go to elecraft for repairs.

Thanks
Don

~73
Don
KD8NNU
FH#4107
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 Suggestion - Remember Frequency per Band Mode

[Bill W]

This might be a very later reply but it you use the "K3 / KX3 Frequency
Memory Editor" software available off the Elecraft Website, to make loading
both Frequency and Mode starting points for each band a breeze. You can then
just hold M>V and your memory detail/discription will be shown on the VFO B
window. You can then use VFO A to select the band segment and mode you
loaded. Then tap M>V and you are there. 



--
View this message in context: 
http://elecraft.365791.n2.nabble.com/K3-Suggestion-Remember-Frequency-per-Band-Mode-tp7560928p7561661.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] [K3] Problem w/front panel switches

[David Pratt]

Phil - Have you tried re-installing the Front Panel firmware?  Just a
thought.

73 de David G4DMP

In a recent message, Phil & Debbie Salas  writes
>BTW - I can switch bands using the buttons on my KPA500, and it transmits
>fine.  Just front panel button problems.
-- 
 + - - - - - - - - - - - - - - - - +
 | David M Pratt, Kippax, Leeds.   |
 | Website: http://www.g4dmp.co.uk |
 + - - - - - - - - - - - - - - - - +

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] The next new radio from Japan?

[Buck k4ia]

I like the clever design of the control head but -
Upconversion
Over 6 pounds
1.2 Amp on standby
No internal antenna tuner mentioned
Mandatory D-$tar

Seems like a combination of the worst of the old and new in what is 
likely to be a very expensive package.


Buck
k4ia
K3 # 101  KX3 #715

On 8/26/2012 11:17 AM, Gary wrote:
> I saw this press release and thought I share it. It seems Icom (Japan) has
> introduced their new all band/all mode amateur transceiver. It will likely
> be some time before we see some version of it in the USA. More info can be
> seen at: http://www.icomuk.co.uk/News_Article/3508/17675/
>
> Gary
>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 and the THP HL-1.5KFX

“Has anyone successfully interfaced a K3 and THP HL-1.5KFX amp so the K3 tells 
the amp what band to be on? If so, I would appreciate specifics onhow you did 
it.”

Peter – Just connect the K3 0123 band data outputs to the THP ABCD band data 
inputs.  On the THP, tell it is a Yaesu input.  The only issue is that when the 
THP amp is off, it loads down the K3 band data outputs.  The THP 1.5 and 2.5 
amps really need isolation diodes to keep this from happening, though it is 
really only a problem if you are powering other devices in parallel with a 
turned-off THP amp.

Phil – AD5X
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] [K3] Problem w/front panel switches

[Phil & Debbie Salas]

Well - Thought I'd put this out here since it'll be tomorrow before I can 
contact Elecraft Support.

This morning my K3 (SN308) started having problems with the front panel 
controls.  I can't change bands with the BAND button, pressing the MODE 
button changes antennas, pressing the M>V button plays my M1 CW message, 
etc.  I re-loaded all firmware, and I pulled the front panel loose and 
dabbed some DeOxit on the connector (I've heard of problems with the tin 
plated pins which I have).  Anyway, no joy.  Anyone see anything familiar, 
and know of a solution?

BTW - I can switch bands using the buttons on my KPA500, and it transmits 
fine.  Just front panel button problems.

Thanks,
Phil - AD5X 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] The next new radio from Japan?

[Gary]

I saw this press release and thought I share it. It seems Icom (Japan) has
introduced their new all band/all mode amateur transceiver. It will likely
be some time before we see some version of it in the USA. More info can be
seen at: http://www.icomuk.co.uk/News_Article/3508/17675/

Gary

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] New convert

[Tony Estep]

A few months ago a ham buddy of mine, K0CEH, came over to see my HF
antenna. While in the shack, he asked about my K3 & KPA500, and I gave him
a 1-minute demo, and told him about the upcoming KX3. Shortly afterward, he
went to Dayton, saw a KX3 at the Elecraft booth,  and ordered one.

My KX3 came while he was waiting for his to be shipped, and when he called
to ask questions about it, we started talking some more about the K3 and
amp. He came back to make another visit my shack, this time to get details
on my panadapter and software setup, and again I gave him a 1-minute demo
of the gear. It wasn't long before he had ordered both of them. I don't
think his KX3 has arrived yet, but he now has both K3 and amp set up and
running and is a delighted new user. So another joins the ranks of the
converted.

Tony KT0NY


-- 
http://www.isb.edu/faculty/facultydir.aspx?ddlFaculty=352
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] KX3 intro at San Diego Six Shooters

[Keith Heimbold]

I had the opportunity to do a small introduction of my recently arrived KX3 at 
the San Diego Six Shooters meeting in Santee, CA last week. 

It was a nice time and many questions were asked and answered. Fortunately for 
me there was an old time Elecraft expert in the crowd who was a K3 owner that 
could answer questions about the rig and Elecraft that I could not (seemed to 
be a personal acquaintance of Wayne's).

The biggest uproar in the presentation was when I told the group of the new 
Sherwood rankings and how much this new rig costs in comparison to the FTDX5000 
and other high end rigs. I made sure to mention that the rigs serve different 
purposes obviosuly ie mine is destined to be my mobile, but even still I am 
sure that an order or two will come out of that group of fifty or so attendees. 
There was certainly a look of shared shock and dismay among some and nods and 
smiles among many.

The interesting part for me was how I felt when presenting the rig. I was very 
proud to stand there and represent being an owner of several Elecraft products. 
I have done a lot of sales and marketing for my own business nationally and 
internationally have done it for large G2000 companies and have not always felt 
so stoked about what i was representing. However, I felt great talking abou my 
K3s and KX3 in particular. Maybe it Is the hobby influence but it is special 
talking about superior products with a tremendous value proposition like the K3 
and KX3. 

Wayne and Eric and crew really do have something very special. BZ Gents and 
Ladies from Elecraft.

Best Regards & 73,

Keith 
AG6AZ

Sent from my iPhone please excuse typos
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] K3 and the THP HL-1.5KFX

[Peter Chamalian]

Has anyone successfully interfaced a K3 and THP HL-1.5KFX amp so the K3
tells the amp what band to be on?  If so, I would appreciate specifics on
how you did it.

 

Thanks,

 

Pete, W1RM

 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html