Re: [Elecraft] KX2 on JT65 & JT9 ??

[Wayne Burdick]

Lyle is on vacation and didn't get that memo. He's above and beyond the call of 
duty posting at all :)

Also note that the latest production KX3 RF board (rev. E) has the synth 
circuitry a lot farther from the PA and driver. This significantly reduced the 
thermal gradient. (The other major Rev. E RF board improvement was tighter 
17/15/12/10 meter band-pass filters. These were inherited by the KX2 as well.)

Wayne
N6KR 



On May 29, 2016, at 8:50 PM, D Howard  wrote:

> Lyle
> Such data would be very beneficial.
> And result in more KX2 sales - ha if that could be handled!!
> Note that Wayne just posted that a temp comp procedure will be posted.
> Dan VA3MA
> 
>> On May 29, 2016, at 11:45 PM, Lyle  wrote:
>> 
>> The local oscillator design of the KX2 is very different from the KX3, as 
>> are the thermal isolation of the oscillator from the PA and the high current 
>> paths in the radio.  There is as yet no field temperature compensation 
>> procedure available for the KX2 nor is it clear that one is needed.  At 
>> least one  KX2 field tester operated JT65 successfully with the KX2.
>> 
>> There are enough KX2 radios in the field now that it should be a simple 
>> matter for an owner to measure the stability of the radio in this mode and 
>> report the results to the group to satisfy the curious...
>> 
>> 73,
>> 
>> Lyle KK7P (on "vacation")
>> 
>> Sent from my iPhone
>> 
>>> On May 29, 2016, at 8:14 PM, Dan - VA3MA  wrote:
>>> 
>>> Luke
>>> Thanks - just what I needed to know!
>>> Have you tried JT9 ?
>>> Perhaps some sort of heatsink/handles added to the case might help??
>>> 73
>>> Dan VA3MA
>>> 
>>> 
>>> On 2016-05-29, at 22:37, Luke  wrote:
>>> 
>>> Hmm, not sure why it cut out my message. Here's what I wrote:
>>> 
>>> I've used my KX2 on WSPR and JT65 and it appears to be plenty stable. I 
>>> used to have a KX3  and sold it because it wouldn't decode WSPR between 
>>> transmit cycles due to excessive drift. I've kept the KX2 to <5 watts 
>>> because the right sideplate gets very hot with the high duty cycle.
>>> 
>>> I've actually just been sitting here running JT65 @ 10 watts when I got 
>>> your email, and it is doing pretty well. I had 3 back to back QSO's and on 
>>> the last transmission the PA Temp got up to 47C (~117F) which doesn't seem 
>>> too bad. As it cools off there is no drifting or slanting of signals on the 
>>> waterfall either. I think the 1 minute on/off duty cycle of JT65 is very 
>>> doable with the KX2, and WSPR might be pushing it. The other night the 
>>> sideplate got quite hot running WSPR at 5 watts.
>>> 
>>> Luke
>>> AD0KI
>>> 
>>> 
>>> From: Dan - VA3MA 
>>> To: Luke  
>>> Sent: Sunday, May 29, 2016 8:12 PM
>>> Subject: Re: [Elecraft] KX2 on JT65 & JT9 ??
>>> 
>>> Luke
>>> No content
>>> 
 On May 29, 2016, at 8:51 PM, Luke via Elecraft  
 wrote:
 
 
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net
 
 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
 Message delivered to va...@me.com
>>> 
>>> __
>>> Elecraft mailing list
>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>>> Help: http://mailman.qth.net/mmfaq.htm
>>> Post: mailto:Elecraft@mailman.qth.net
>>> 
>>> This list hosted by: http://www.qsl.net
>>> Please help support this email list: http://www.qsl.net/donate.html
>>> Message delivered to kk7p4...@gmail.com
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@elecraft.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Audacity recorder with Xonar U& & NaP3

[Dave Blaschke, w5un]

Is anyone here running their K3 with LP-Pan, NaP3, and  Xonar U7 sound 
card? I am attempting to make Audacity work with this scheme, but am 
unable to get it to record.


Dave, W5UN
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] FS: KX-1

[W0FK]

Sold! 



-
St. Louis, MO


--
View this message in context: 
http://elecraft.365791.n2.nabble.com/FS-KX-1-tp7618179p7618217.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K3 and Signallink next the Microham

[Ross]

Thanks for the comments.
The Microham is the Keyer II.
I have connected the line in,line out and the usb cable to the pc, are there 
any other connections I need to make??

Yes the multicore cable from the k3 is the one for the k3 it is marked k3.
Thanks
Ross
-Original Message- 
From: Joe Subich, W4TV

Sent: Monday, May 30, 2016 2:21 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 and Signallink next the Microham



Next to try and set up the microham for digital work.


Which microHAM Interface?

In general, set the K3/K3S to DATA mode and select MENU:MIC SEL =
LINE IN, set Mic Gain (LINE) to about 15 and configure the microHAM
interface audio levels as documented in the "Setting Audio Levels"
section of the microHAM Users Manual.  As a final "touch up" adjust
the K3 "Mic Gain" for four bars of ALC (the fifth bar can flicker).


73,

   ... Joe, W4TV

On 5/29/2016 6:54 PM, Ross wrote:

Thanks for all the comments about the signal link.
I found the problem when checking Airlink express, I had the volume and tx 
levels set to almost zero, in Airlink express so whenI reset them to max, 
everything popped into life and all my other digital programs then worked 
perfectly.


Next to try and set up the microham for digital work.
All advice very gratefully accepted.
Thanks
Ross
ZL1WN
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to li...@subich.com


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to rbig...@ihug.co.nz 


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 on JT65 & JT9 ??

[D Howard]

Lyle
Such data would be very beneficial.
And result in more KX2 sales - ha if that could be handled!!
Note that Wayne just posted that a temp comp procedure will be posted.
Dan VA3MA

> On May 29, 2016, at 11:45 PM, Lyle  wrote:
> 
> The local oscillator design of the KX2 is very different from the KX3, as are 
> the thermal isolation of the oscillator from the PA and the high current 
> paths in the radio.  There is as yet no field temperature compensation 
> procedure available for the KX2 nor is it clear that one is needed.  At least 
> one  KX2 field tester operated JT65 successfully with the KX2.
> 
> There are enough KX2 radios in the field now that it should be a simple 
> matter for an owner to measure the stability of the radio in this mode and 
> report the results to the group to satisfy the curious...
> 
> 73,
> 
> Lyle KK7P (on "vacation")
> 
> Sent from my iPhone
> 
>> On May 29, 2016, at 8:14 PM, Dan - VA3MA  wrote:
>> 
>> Luke
>> Thanks - just what I needed to know!
>> Have you tried JT9 ?
>> Perhaps some sort of heatsink/handles added to the case might help??
>> 73
>> Dan VA3MA
>> 
>> 
>> On 2016-05-29, at 22:37, Luke  wrote:
>> 
>> Hmm, not sure why it cut out my message. Here's what I wrote:
>> 
>> I've used my KX2 on WSPR and JT65 and it appears to be plenty stable. I used 
>> to have a KX3  and sold it because it wouldn't decode WSPR between transmit 
>> cycles due to excessive drift. I've kept the KX2 to <5 watts because the 
>> right sideplate gets very hot with the high duty cycle.
>> 
>> I've actually just been sitting here running JT65 @ 10 watts when I got your 
>> email, and it is doing pretty well. I had 3 back to back QSO's and on the 
>> last transmission the PA Temp got up to 47C (~117F) which doesn't seem too 
>> bad. As it cools off there is no drifting or slanting of signals on the 
>> waterfall either. I think the 1 minute on/off duty cycle of JT65 is very 
>> doable with the KX2, and WSPR might be pushing it. The other night the 
>> sideplate got quite hot running WSPR at 5 watts.
>> 
>> Luke
>> AD0KI
>> 
>> 
>> From: Dan - VA3MA 
>> To: Luke  
>> Sent: Sunday, May 29, 2016 8:12 PM
>> Subject: Re: [Elecraft] KX2 on JT65 & JT9 ??
>> 
>> Luke
>> No content
>> 
>>> On May 29, 2016, at 8:51 PM, Luke via Elecraft  
>>> wrote:
>>> 
>>> 
>>> __
>>> Elecraft mailing list
>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>>> Help: http://mailman.qth.net/mmfaq.htm
>>> Post: mailto:Elecraft@mailman.qth.net
>>> 
>>> This list hosted by: http://www.qsl.net
>>> Please help support this email list: http://www.qsl.net/donate.html
>>> Message delivered to va...@me.com
>> 
>> __
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft@mailman.qth.net
>> 
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to kk7p4...@gmail.com
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 on JT65 & JT9 ??

[D Howard]

Luke
I too sold my KX3 for the same reason- no WSJT. 
Happy to see KX2 capable with care
Dan

> On May 29, 2016, at 11:20 PM, Luke  wrote:
> 
> I just tried JT9 actually and had no problems. If you head over to 
> PSKReporter and type in my call sign you can see how it's been working for me 
> this evening. It seems to heat up a little faster using JT9, but it's still 
> managable. I don't mind taking a few minutes between QSO's to let things cool 
> off. From my understanding Gemsproducts.com already has KX2 side handles in 
> the works and I will definitely pick some up and see how they work. I can 
> only imagine that any more metal on the side to pick up some extra heat will 
> only be a good thing.
> 
> Luke
> AD0KI
> 
> 
> 
> 
> From: Dan - VA3MA 
> To: Luke  
> Cc: Elecraft 
> Sent: Sunday, May 29, 2016 9:14 PM
> Subject: Re: [Elecraft] KX2 on JT65 & JT9 ??
> 
> Luke
> Thanks - just what I needed to know!
> Have you tried JT9 ?
> Perhaps some sort of heatsink/handles added to the case might help??
> 73
> Dan VA3MA
> 
> 
> On 2016-05-29, at 22:37, Luke  wrote:
> 
> Hmm, not sure why it cut out my message. Here's what I wrote:
> 
> I've used my KX2 on WSPR and JT65 and it appears to be plenty stable. I used 
> to have a KX3  and sold it because it wouldn't decode WSPR between transmit 
> cycles due to excessive drift. I've kept the KX2 to <5 watts because the 
> right sideplate gets very hot with the high duty cycle.
> 
> I've actually just been sitting here running JT65 @ 10 watts when I got your 
> email, and it is doing pretty well. I had 3 back to back QSO's and on the 
> last transmission the PA Temp got up to 47C (~117F) which doesn't seem too 
> bad. As it cools off there is no drifting or slanting of signals on the 
> waterfall either. I think the 1 minute on/off duty cycle of JT65 is very 
> doable with the KX2, and WSPR might be pushing it. The other night the 
> sideplate got quite hot running WSPR at 5 watts.
> 
> Luke
> AD0KI
> 
> 
> From: Dan - VA3MA 
> To: Luke  
> Sent: Sunday, May 29, 2016 8:12 PM
> Subject: Re: [Elecraft] KX2 on JT65 & JT9 ??
> 
> Luke
> No content
> 
> > On May 29, 2016, at 8:51 PM, Luke via Elecraft  
> > wrote:
> > 
> > 
> > __
> > Elecraft mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/elecraft
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:Elecraft@mailman.qth.net
> > 
> > This list hosted by: http://www.qsl.net
> > Please help support this email list: http://www.qsl.net/donate.html
> > Message delivered to va...@me.com
> 
> 
> 
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 on JT65 & JT9 ??

[Lyle]

The local oscillator design of the KX2 is very different from the KX3, as are 
the thermal isolation of the oscillator from the PA and the high current paths 
in the radio.  There is as yet no field temperature compensation procedure 
available for the KX2 nor is it clear that one is needed.  At least one  KX2 
field tester operated JT65 successfully with the KX2.

There are enough KX2 radios in the field now that it should be a simple matter 
for an owner to measure the stability of the radio in this mode and report the 
results to the group to satisfy the curious...

73,

Lyle KK7P (on "vacation")

Sent from my iPhone

> On May 29, 2016, at 8:14 PM, Dan - VA3MA  wrote:
> 
> Luke
> Thanks - just what I needed to know!
> Have you tried JT9 ?
> Perhaps some sort of heatsink/handles added to the case might help??
> 73
> Dan VA3MA
> 
> 
> On 2016-05-29, at 22:37, Luke  wrote:
> 
> Hmm, not sure why it cut out my message. Here's what I wrote:
> 
> I've used my KX2 on WSPR and JT65 and it appears to be plenty stable. I used 
> to have a KX3  and sold it because it wouldn't decode WSPR between transmit 
> cycles due to excessive drift. I've kept the KX2 to <5 watts because the 
> right sideplate gets very hot with the high duty cycle.
> 
> I've actually just been sitting here running JT65 @ 10 watts when I got your 
> email, and it is doing pretty well. I had 3 back to back QSO's and on the 
> last transmission the PA Temp got up to 47C (~117F) which doesn't seem too 
> bad. As it cools off there is no drifting or slanting of signals on the 
> waterfall either. I think the 1 minute on/off duty cycle of JT65 is very 
> doable with the KX2, and WSPR might be pushing it. The other night the 
> sideplate got quite hot running WSPR at 5 watts.
> 
> Luke
> AD0KI
> 
> 
> From: Dan - VA3MA 
> To: Luke  
> Sent: Sunday, May 29, 2016 8:12 PM
> Subject: Re: [Elecraft] KX2 on JT65 & JT9 ??
> 
> Luke
> No content
> 
>> On May 29, 2016, at 8:51 PM, Luke via Elecraft  
>> wrote:
>> 
>> 
>> __
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft@mailman.qth.net
>> 
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to va...@me.com
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to kk7p4...@gmail.com
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 on JT65 & JT9 ??

[D Howard]

Wayne
I would imagine a bit of cooling on the KX2 end plate will help also? Heat 
sink...
Happy to see it is within limits for WSJT modes without freezing it!! Hi hi
Dan VA3MA


> On May 29, 2016, at 11:35 PM, Wayne Burdick  wrote:
> 
> I'm glad it's working. But just in case, we will also be providing an 
> optional extended temperature compensation procedure for the KX2.
> 
> 73,
> Wayne
> 
> 
>> On 2016-05-29, at 22:37, Luke  wrote:
>> 
>> Hmm, not sure why it cut out my message. Here's what I wrote:
>> 
>> I've used my KX2 on WSPR and JT65 and it appears to be plenty stable. I used 
>> to have a KX3  and sold it because it wouldn't decode WSPR between transmit 
>> cycles due to excessive drift. I've kept the KX2 to <5 watts because the 
>> right sideplate gets very hot with the high duty cycle.
>> 
>> I've actually just been sitting here running JT65 @ 10 watts when I got your 
>> email, and it is doing pretty well. I had 3 back to back QSO's and on the 
>> last transmission the PA Temp got up to 47C (~117F) which doesn't seem too 
>> bad. As it cools off there is no drifting or slanting of signals on the 
>> waterfall either. I think the 1 minute on/off duty cycle of JT65 is very 
>> doable with the KX2, and WSPR might be pushing it. The other night the 
>> sideplate got quite hot running WSPR at 5 watts.
>> 
>> Luke
>> AD0KI
> 
> 
> 
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 on JT65 & JT9 ??

[Wayne Burdick]

I'm glad it's working. But just in case, we will also be providing an optional 
extended temperature compensation procedure for the KX2.

73,
Wayne


> On 2016-05-29, at 22:37, Luke  wrote:
> 
> Hmm, not sure why it cut out my message. Here's what I wrote:
> 
> I've used my KX2 on WSPR and JT65 and it appears to be plenty stable. I used 
> to have a KX3  and sold it because it wouldn't decode WSPR between transmit 
> cycles due to excessive drift. I've kept the KX2 to <5 watts because the 
> right sideplate gets very hot with the high duty cycle.
> 
> I've actually just been sitting here running JT65 @ 10 watts when I got your 
> email, and it is doing pretty well. I had 3 back to back QSO's and on the 
> last transmission the PA Temp got up to 47C (~117F) which doesn't seem too 
> bad. As it cools off there is no drifting or slanting of signals on the 
> waterfall either. I think the 1 minute on/off duty cycle of JT65 is very 
> doable with the KX2, and WSPR might be pushing it. The other night the 
> sideplate got quite hot running WSPR at 5 watts.
> 
> Luke
> AD0KI



__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 on JT65 & JT9 ??

[Dan - VA3MA]

Luke
Thanks - just what I needed to know!
Have you tried JT9 ?
Perhaps some sort of heatsink/handles added to the case might help??
73
Dan VA3MA


On 2016-05-29, at 22:37, Luke  wrote:

Hmm, not sure why it cut out my message. Here's what I wrote:

I've used my KX2 on WSPR and JT65 and it appears to be plenty stable. I used to 
have a KX3  and sold it because it wouldn't decode WSPR between transmit cycles 
due to excessive drift. I've kept the KX2 to <5 watts because the right 
sideplate gets very hot with the high duty cycle.

I've actually just been sitting here running JT65 @ 10 watts when I got your 
email, and it is doing pretty well. I had 3 back to back QSO's and on the last 
transmission the PA Temp got up to 47C (~117F) which doesn't seem too bad. As 
it cools off there is no drifting or slanting of signals on the waterfall 
either. I think the 1 minute on/off duty cycle of JT65 is very doable with the 
KX2, and WSPR might be pushing it. The other night the sideplate got quite hot 
running WSPR at 5 watts.

Luke
AD0KI


From: Dan - VA3MA 
To: Luke  
Sent: Sunday, May 29, 2016 8:12 PM
Subject: Re: [Elecraft] KX2 on JT65 & JT9 ??

Luke
No content

> On May 29, 2016, at 8:51 PM, Luke via Elecraft  
> wrote:
> 
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to va...@me.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 on JT65 & JT9 ??

[Tony Estep]

>
>
> Issues with not being able to communicate with JT65 have nothing to do with
> frequency stability

===
Actually, frequency stability is the key issue with JT65. The transmit
frequency can not drift more than about 8 hz during transmission, or the
receiving station will probably not be able to copy. It was this exact
issue that led to the development of the temp compensation scheme for the
KX3. The point of the original question was to determine whether or not the
KX2 needs such a compensation routine, or is stable enough as shipped.

If you run a KX3 without the compensation you may think they can't hear you
when actually the problem is in the small drift in your transmit frequency.
I first discovered this when running WSPR on the KX3 and listening to
myself on a nearby K3. The graphic display of carrier frequency offered by
WSPR made it clear what was happening. My stock KX3 drifted by about 14 Hz
in the first half-minute or so of transmission. Contacts on JT65 were not
impossible, but they were rare, as were WSPR reports.

You can search the archives for many, many posts on this subject, and look
on the Elecraft website for the recommended fix, which involves putting
your KX3 in the fridge, then running a compensation routine while you warm
it up with a heat gun.

Meanwhile, I would be interested to know the answer to the original
question, as I am sure many others would be as well.

Tony KT0NY
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 on JT65 & JT9 ??

[Michael Walker]

The moon bounces around and causes some pretty good doppler.

Good thing that JT65-HF also has AFC built in.

http://www.packetradio.com/pdfzips/jt65-hf-setup.pdf

*AFC enables automatic frequency control and will attempt to follow a
signal that exhibits drift. Its original intent is to compensate for
Doppler shift when using JT65 for EME contacts, but it has application on
HF as well. Not for Doppler shift compensation, but for stations who show
VFO drift.*

The biggest problem is clock drift, not RF drift.

Regardless, the beta testers claimed the did JT65 without issue.

Mike va3mw


On Sun, May 29, 2016 at 8:51 PM, Luke via Elecraft  wrote:

>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to va...@portcredit.net
>
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3 and Signallink next the Microham

[Joe Subich, W4TV]

> Next to try and set up the microham for digital work.

Which microHAM Interface?

In general, set the K3/K3S to DATA mode and select MENU:MIC SEL =
LINE IN, set Mic Gain (LINE) to about 15 and configure the microHAM
interface audio levels as documented in the "Setting Audio Levels"
section of the microHAM Users Manual.  As a final "touch up" adjust
the K3 "Mic Gain" for four bars of ALC (the fifth bar can flicker).


73,

   ... Joe, W4TV

On 5/29/2016 6:54 PM, Ross wrote:

Thanks for all the comments about the signal link.
I found the problem when checking Airlink express, I had the volume and tx 
levels set to almost zero, in Airlink express so whenI reset them to max, 
everything popped into life and all my other digital programs then worked 
perfectly.

Next to try and set up the microham for digital work.
All advice very gratefully accepted.
Thanks
Ross
ZL1WN
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to li...@subich.com


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] KX3 Auto Power Off suggestion

[Thorpe, Jeffrey]

Just a suggestion for an upcoming firmware update:

How about allowing an auto power off more selectable than 20 minutes or less 
(plus infinite)?

Sometimes I need to leave, and while I am recording to my tablet, I'll be gone 
for a few hours, coming back to everything dead (batteries in both).

Being able to select up to, say, an hour, would be good (for me at least).

Jeff - KG7HDZ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 on JT65 & JT9 ??

[Luke via Elecraft]

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3 and Signallink

[Mike Dodd]

On 5/29/2016 4:45 PM, Ross wrote:

...the Signallink is working perfectly,
it produces the output and keys the k3, but I cannot get any audio,
the line in and lineout plugs are in the correct positions on the
k3. So can someone please guide me as to what could be wrong, would
it be the settings on the k3 or something else.


Just a stab in the dark Have you selected the correct audio input 
for digital mode on the menu?


My K3s has the built-in USB sound card, so I don't know what menu 
selections are available without one.


Are you sure the SignaLink is producing audio? Have you listened with 
phones plugged into its monitor(?) jack?


--
73, Mike N4CF
Louisa County, VA USA
Elecraft K3s/100
Carolina Windom up 45'
http://n4cf.mdodd.com
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3 and Signallink next the Microham

[Mike Reublin NF4L]

Why would you use two interfaces for digital?

73, Mike NF4L

> On May 29, 2016, at 6:54 PM, Ross  wrote:
> 
> Thanks for all the comments about the signal link.
> I found the problem when checking Airlink express, I had the volume and tx 
> levels set to almost zero, in Airlink express so whenI reset them to max, 
> everything popped into life and all my other digital programs then worked 
> perfectly.
> 
> Next to try and set up the microham for digital work.
> All advice very gratefully accepted.
> Thanks
> Ross
> ZL1WN
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@comcast.net

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 on JT65 & JT9 ??

[Josh Fiden]

Yes, but... the earth & moon don't do anything abrupt.

73,
Josh W6XU

On 5/29/2016 1:33 PM, Michael Walker wrote:

...does not require a super stable transmitter.  In fact, when they use it off
the moon, there is significant doppler going on.


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Beep

[Wayne Burdick]

I'll add this to the high-priority bug list.

73,
Wayne
N6KR


On May 29, 2016, at 4:13 PM, "Jeff Herr"  wrote:

> That is a no go.
> 
> 
> -Original Message-
> From: Wayne Burdick [mailto:n...@elecraft.com] 
> Sent: Sunday, May 29, 2016 14:07 PM
> To: Jeff Herr
> Cc: elecraft@mailman.qth.net
> Subject: Re: [Elecraft] Beep
> 
> This may be due to a switch emulation command being sent. If so, you could
> set MENU:SW TONE to OFF.
> 
> 73,
> Wayne
> N6KR
> 
> 
> On May 28, 2016, at 7:22 PM, Jeff Herr  wrote:
> 
>> In regard to the Elecraft Frequency Memory Editor:
>> 
>> When using the QSY capability the KX3 does a beep.
>> 
>> When I am up late at night this is problematic.
>> 
>> Is there a way to turn off the "beep"
>> 
>> __
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft@mailman.qth.net
>> 
>> This list hosted by: http://www.qsl.net Please help support this email 
>> list: http://www.qsl.net/donate.html Message delivered to 
>> n...@elecraft.com
> 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Beep

[Jeff Herr]

That is a no go.


-Original Message-
From: Wayne Burdick [mailto:n...@elecraft.com] 
Sent: Sunday, May 29, 2016 14:07 PM
To: Jeff Herr
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] Beep

This may be due to a switch emulation command being sent. If so, you could
set MENU:SW TONE to OFF.

73,
Wayne
N6KR


On May 28, 2016, at 7:22 PM, Jeff Herr  wrote:

> In regard to the Elecraft Frequency Memory Editor:
> 
> When using the QSY capability the KX3 does a beep.
> 
> When I am up late at night this is problematic.
> 
> Is there a way to turn off the "beep"
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net Please help support this email 
> list: http://www.qsl.net/donate.html Message delivered to 
> n...@elecraft.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Strong Rd feedback in mh3

[Edouard Lafargue]

  Thanks everyone! Good advice. Now that I have better Internet access
again (btw I meant "RF" not "Rd" in the subject line, of course), I
discovered this article on ... elecraft.com :
http://www.elecraft.com/Apps/eliminating_tx_rf_feedback_probl.htm   :-)

   I will experiment with less random lengths for my random wires, and
better counterpoises, and a small balun if necessary.

73 de ed w6ela

On Sun, May 29, 2016 at 2:05 PM, Wayne Burdick  wrote:

> Also try a QRP balun at the radio, such as our BL1 or BL2.
>
> 73,
> Wayne
> N6KR
>
>
> On May 28, 2016, at 8:43 PM, Don Wilhelm  wrote:
>
> > Ed,
> >
> > Yes, that can be common with long wire antennas - that can happen with
> any transceiver, it is not unique to the K3 or KX3.
> >
> > Change the length of your long wire by 1/8 wavelength at the frequency
> you are having trouble with.
> >
> > The situation is that you have a high RF voltage on that antenna near
> the shack end.
> > Even though the tuner can match it, it can produce a strong RF Field in
> the shack.
> >
> > 73,
> > Don W3FPR
> >
> > On 5/28/2016 11:17 PM, Edouard Lafargue wrote:
> >> I was operating portable today, with a long wire in a tree  and
> >> counterpoise on the ground, and no matter what I did, every time I
> pushed
> >> the mic button, I got super strong RF feedback in audio monitoring,
> >> apparently picked up by the MH3 cable - things got slightly better if I
> >> tried to bunch/coil the MH3 cable. Is this common?
> >>
> >> I only managed to work one station in Indiana in the time I tried, most
> of
> >> the time what I heard in my headphones while transmitting was
> >> unintelligible garble, so it is no surprise others didn't hear me, I
> >> guess...
> >>
> >> My KX3 has got an internal ATU and it managed to match the long wire
> >> perfectly at each frequency I tried to operate...
> >>
> >>
> >
> > __
> > Elecraft mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/elecraft
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:Elecraft@mailman.qth.net
> >
> > This list hosted by: http://www.qsl.net
> > Please help support this email list: http://www.qsl.net/donate.html
> > Message delivered to n...@elecraft.com
>
>
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K3 and Signallink next the Microham

[Ross]

Thanks for all the comments about the signal link.
I found the problem when checking Airlink express, I had the volume and tx 
levels set to almost zero, in Airlink express so whenI reset them to max, 
everything popped into life and all my other digital programs then worked 
perfectly.

Next to try and set up the microham for digital work.
All advice very gratefully accepted.
Thanks
Ross
ZL1WN
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] KX2 Eyeball at DFARG

[w4sc]

KX2 had an impromptu eyeball with AK4Y, K4FI, W4DRH, W4EFZ, KK4DSD, W1TEF, and 
W4SJD and others at the Dutch Fork Amateur Radio Group’s shack.  All attendees 
were impressed with the radio and it performance.  It was a hit!! I expect the 
waiting list to be longer by Monday.

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Fwd: Re: K3 and Signallink

[Kevin Stover]

 Forwarded Message 
Subject:Re: [Elecraft] K3 and Signallink
Date:   Sun, 29 May 2016 16:19:26 -0500
From:   Kevin Stover 
To: elecraft@mailman.qth.net



Did you check the line in and line out levels?

On 5/29/2016 3:45 PM, Ross wrote:

I have just checked my K3 again after a couple of months not using it, and I 
have a problem with the Signallink.
Yes I know all the comments about it, but I want to get it going before I try 
to instal the Microham keyer.
On transmit the Signallink is working perfectly, it produces the output and 
keys the k3, but I cannot get any audio, the line in and lineout plugs are in 
the correct positions on the k3.
So can someone please guide me as to what could be wrong, would it be the 
settings on the k3 or something else.
(I have checked 2 digital programs with the same result, transmit is ok, but no 
audio coming through.)

Thanks
Ross
ZL1WN
__
Elecraft mailing list
Home:http://mailman.qth.net/mailman/listinfo/elecraft
Help:http://mailman.qth.net/mmfaq.htm
Post:mailto:Elecraft@mailman.qth.net

This list hosted by:http://www.qsl.net
Please help support this email list:http://www.qsl.net/donate.html
Message delivered tokevin.sto...@mediacombb.net




--
R. Kevin Stover
AC0H
ARRL
FISTS #11993
SKCC #215
NAQCC #3441



---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Beep

[Wayne Burdick]

This may be due to a switch emulation command being sent. If so, you could set 
MENU:SW TONE to OFF.

73,
Wayne
N6KR


On May 28, 2016, at 7:22 PM, Jeff Herr  wrote:

> In regard to the Elecraft Frequency Memory Editor:
> 
> When using the QSY capability the KX3 does a beep.
> 
> When I am up late at night this is problematic.
> 
> Is there a way to turn off the "beep"
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@elecraft.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Strong Rd feedback in mh3

[Wayne Burdick]

Also try a QRP balun at the radio, such as our BL1 or BL2.

73,
Wayne
N6KR


On May 28, 2016, at 8:43 PM, Don Wilhelm  wrote:

> Ed,
> 
> Yes, that can be common with long wire antennas - that can happen with any 
> transceiver, it is not unique to the K3 or KX3.
> 
> Change the length of your long wire by 1/8 wavelength at the frequency you 
> are having trouble with.
> 
> The situation is that you have a high RF voltage on that antenna near the 
> shack end.
> Even though the tuner can match it, it can produce a strong RF Field in the 
> shack.
> 
> 73,
> Don W3FPR
> 
> On 5/28/2016 11:17 PM, Edouard Lafargue wrote:
>> I was operating portable today, with a long wire in a tree  and
>> counterpoise on the ground, and no matter what I did, every time I pushed
>> the mic button, I got super strong RF feedback in audio monitoring,
>> apparently picked up by the MH3 cable - things got slightly better if I
>> tried to bunch/coil the MH3 cable. Is this common?
>> 
>> I only managed to work one station in Indiana in the time I tried, most of
>> the time what I heard in my headphones while transmitting was
>> unintelligible garble, so it is no surprise others didn't hear me, I
>> guess...
>> 
>> My KX3 has got an internal ATU and it managed to match the long wire
>> perfectly at each frequency I tried to operate...
>> 
>> 
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@elecraft.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 on JT65 & JT9 ??

[Michael Walker]

I have run JT65 on my KX3 at 5 watts without issue other than not having
enough RF signal.

Mike va3mw


On Sun, May 29, 2016 at 4:37 PM, Dan Howard  wrote:

> Mike
> The KX3 wil not work JT modes due to freq drift due to heat - one must do
> the temperature compensation procedure in order to get the KX3
> freq stable…
> I’m hoping that the KX2 does not need ‘fiddling’ in a cooler ! HIHI
> 73
> Dan
>
> > On May 29, 2016, at 4:33 PM, Michael Walker 
> wrote:
> >
> > Dan
> >
> > Issues with not being able to communicate with JT65 have nothing to do
> with
> > frequency stability.  It has to do with just not being heard.  :)
> >
> > Like all other digital modes, you require Transmit and Receive Audio and
> a
> > PTT line.
> >
> > I would be very very very surprised that a KX2 can't handle JT65.  JT65
> is
> > does not require a super stable transmitter.  In fact, when they use it
> off
> > the moon, there is significant doppler going on.
> >
> > Mike va3mw
> >
> >
> > On Sun, May 29, 2016 at 4:22 PM, Dan - VA3MA  wrote:
> >
> >> Hi  thanks
> >> I’ve read all these c comments by others - but I have yet to get a
> direct
> >> confirmation from someone who has operated the KX2 enthuse digital
> modes!
> >> Ha!
> >> Dan
> >>
> >>> On May 29, 2016, at 3:46 PM, Phil Wheeler  wrote:
> >>>
> >>> One of the eham reviewers mentioned using the KX2 on JT65:
> >> http://www.eham.net/reviews/detail/12852
> >>>
> >>> The N9JR review.
> >>>
> >>> Phil W7OX
> >>>
> >>>
> >>> On 5/29/16 12:40 PM, Dan - VA3MA wrote:
>  Has anyone had the opportunity to see if the KX2 out of the box will
> be
> >> stable enough to run JT65 & JT9
>  Would appreciate feedback as I’m apartment dweller and only run these
> >> digital modes with compromised antenna
>  Thanks
>  Dan VA3MA
> >>>
> >>
> >> __
> >> Elecraft mailing list
> >> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> >> Help: http://mailman.qth.net/mmfaq.htm
> >> Post: mailto:Elecraft@mailman.qth.net
> >>
> >> This list hosted by: http://www.qsl.net
> >> Please help support this email list: http://www.qsl.net/donate.html
> >> Message delivered to va...@portcredit.net
> >>
> > __
> > Elecraft mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/elecraft
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:Elecraft@mailman.qth.net
> >
> > This list hosted by: http://www.qsl.net
> > Please help support this email list: http://www.qsl.net/donate.html
> > Message delivered to va...@me.com
>
>
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K3 and Signallink

[Ross]

I have just checked my K3 again after a couple of months not using it, and I 
have a problem with the Signallink.
Yes I know all the comments about it, but I want to get it going before I try 
to instal the Microham keyer.
On transmit the Signallink is working perfectly, it produces the output and 
keys the k3, but I cannot get any audio, the line in and lineout plugs are in 
the correct positions on the k3.
So can someone please guide me as to what could be wrong, would it be the 
settings on the k3 or something else.
(I have checked 2 digital programs with the same result, transmit is ok, but no 
audio coming through.)

Thanks
Ross
ZL1WN
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 on JT65 & JT9 ??

[Michael Walker]

Dan

Issues with not being able to communicate with JT65 have nothing to do with
frequency stability.  It has to do with just not being heard.  :)

Like all other digital modes, you require Transmit and Receive Audio and a
PTT line.

I would be very very very surprised that a KX2 can't handle JT65.  JT65 is
does not require a super stable transmitter.  In fact, when they use it off
the moon, there is significant doppler going on.

Mike va3mw


On Sun, May 29, 2016 at 4:22 PM, Dan - VA3MA  wrote:

> Hi  thanks
> I’ve read all these c comments by others - but I have yet to get a direct
> confirmation from someone who has operated the KX2 enthuse digital modes!
> Ha!
> Dan
>
> > On May 29, 2016, at 3:46 PM, Phil Wheeler  wrote:
> >
> > One of the eham reviewers mentioned using the KX2 on JT65:
> http://www.eham.net/reviews/detail/12852
> >
> > The N9JR review.
> >
> > Phil W7OX
> >
> >
> > On 5/29/16 12:40 PM, Dan - VA3MA wrote:
> >> Has anyone had the opportunity to see if the KX2 out of the box will be
> stable enough to run JT65 & JT9
> >> Would appreciate feedback as I’m apartment dweller and only run these
> digital modes with compromised antenna
> >> Thanks
> >> Dan VA3MA
> >
>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to va...@portcredit.net
>
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 on JT65 & JT9 ??

[Dan - VA3MA]

Hi  thanks
I’ve read all these c comments by others - but I have yet to get a direct 
confirmation from someone who has operated the KX2 enthuse digital modes!
Ha!
Dan

> On May 29, 2016, at 3:46 PM, Phil Wheeler  wrote:
> 
> One of the eham reviewers mentioned using the KX2 on JT65: 
> http://www.eham.net/reviews/detail/12852
> 
> The N9JR review.
> 
> Phil W7OX
> 
> 
> On 5/29/16 12:40 PM, Dan - VA3MA wrote:
>> Has anyone had the opportunity to see if the KX2 out of the box will be 
>> stable enough to run JT65 & JT9
>> Would appreciate feedback as I’m apartment dweller and only run these 
>> digital modes with compromised antenna
>> Thanks
>> Dan VA3MA
> 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 on JT65 & JT9 ??

[Michael Walker]

I don't believe that JT65 frequency stability at HF frequencies will be an
issue.

The documents say that the JT65 bandwidth is pretty generous.

I've run JT65 on  my Softrock without issue.

Mike va3mw


On Sun, May 29, 2016 at 3:46 PM, Phil Wheeler  wrote:

> One of the eham reviewers mentioned using the KX2 on JT65:
> http://www.eham.net/reviews/detail/12852
>
> The N9JR review.
>
> Phil W7OX
>
>
>
> On 5/29/16 12:40 PM, Dan - VA3MA wrote:
>
>> Has anyone had the opportunity to see if the KX2 out of the box will be
>> stable enough to run JT65 & JT9
>> Would appreciate feedback as I’m apartment dweller and only run these
>> digital modes with compromised antenna
>> Thanks
>> Dan VA3MA
>>
>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to va...@portcredit.net
>
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 on JT65 & JT9 ??

[Phil Wheeler]

One of the eham reviewers mentioned using the KX2 
on JT65: http://www.eham.net/reviews/detail/12852


The N9JR review.

Phil W7OX


On 5/29/16 12:40 PM, Dan - VA3MA wrote:

Has anyone had the opportunity to see if the KX2 out of the box will be stable 
enough to run JT65 & JT9
Would appreciate feedback as I’m apartment dweller and only run these digital 
modes with compromised antenna
Thanks
Dan VA3MA


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] KX2 on JT65 & JT9 ??

[Dan - VA3MA]

Has anyone had the opportunity to see if the KX2 out of the box will be stable 
enough to run JT65 & JT9
Would appreciate feedback as I’m apartment dweller and only run these digital 
modes with compromised antenna
Thanks 
Dan VA3MA
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Elecraft CW Net Announcement

[kev...@coho.net]

Welcome,

   Due to the ongoing WPX contest the first net may or may not run.  If 
there is space from folks dropping out of the race I'll start the twenty 
meter net.  Otherwise I'll just run the forty meter net today.


Please join us on:
14050 kHz at 2200z Sunday (3 PM PDT Sunday)
 7045 kHz at 0100z Monday (6 PM PDT Sunday)

   73,
Kevin.  KD5ONS

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] OT: Wireless stereo headset recommendations

[Jim Rodenkirch]

Danid: check mazon.com.a gaggle of wireless headphones, albeit most
listed as monaural but...I didn't go through the entire listgood luck
 71.5/72 de K9JWV 



--
View this message in context: 
http://elecraft.365791.n2.nabble.com/OT-Wireless-stereo-headset-recommendations-tp7617970p7618185.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Elecraft KX1 for sale

[Thaire Bryant]

Not being used so up for sale:

 

KX1  #2500  80, 40, 30, 20  3-4 watts out on all bands

KXAT1  internal antenna tuner

KXPD1  cw paddles

BNC-BP  BNC to binding post wire antenna adapter

KX1 "Nifty Quick Reference"

Tupperware case

I do not have the manual but it can be downloaded from the Elecraft site.

 

$375 Delivered, Insured Continental US

 

Thaire  W2APF

 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] OT: Wireless stereo headset recommendations

[David Anderson via Elecraft]

Thank you Ed, most useful.

73 from David GM4JJJ

> On 29 May 2016, at 14:51, Ed  wrote:
> 
> David
> 
> There are a number of headsets on the market that will do the job.  What to 
> look for is an inter office device that is used for remote telephone service. 
>  Jabra has an extensive line up as does Panasonic.  I have been using Jarba 
> for years and had very good luck.  The only problem is you won't find any of 
> these that have true stereo.  You can get dual ear pieces but they will be 
> monaural not stereo.  I have copied a link to the Jarba Web Site. They claim 
> stereo but that isn't correct.  They are all monaural. You won't get stereo 
> receive along with a mic. with Bluetooth either.  For that setup you will 
> probably have to look for a Computer Gaming headset.  The list prices are 
> something that will get your attention.  The best I have been able to do is 
> to cruse eBay until something reasonable shows up.  I have been using a 
> GN9460 for about three years.  It's range is in excess of 600 feet.  Very 
> easy to interface to the rig.
> 
> http://jb.factoryoutletstore.com/cat/22458/Jabra-GN-Netcom-Wireless-Headsets.html
> 
> Ed
> K6ED
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to gm4...@yahoo.co.uk

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] New KX2 Video

[Wes Stewart]

 I'll hold my tongue.

On 5/28/2016 5:55 PM, Eric Swartz - WA6HHQ, Elecraft wrote:
Its edited to show each person who called him for a QSO, with the rest in 
between chopped out. He worked each of those stations.


Eric
/elecraft.com/ 


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] About to give up

[Phil Wheeler]

Not new so far as I know, Jim. I've been doing 
that with usb audio devices for some years.


But I must admit I've never operated WSJT-X. And 
when I use PSK31 I use Windows, due to the wider 
availability of ham radio software. My shack 
operating computer is an old 2010 11" MacBook Air, 
chosen because I can see my rigs with it in front 
of them and it has full-size keyboard. It's 
dual-boot OS X 10.11.5 and Windows 10. I do all my 
ham radio work on the Windows side. And for PSK31 
I use Digipan (which I've been using for many 
years) and a Signalink USB.


When I get a chance I'll try fldigi on the OS X 
side with the Signalink USB and see if I run into 
any difficulties of the type you describe.


73, Phil W7OX


On 5/28/16 8:48 PM, James Bennett wrote:

Phil,

Is this something new with El Capitan? I’ve always been making settings changes 
in the MIDI application. Anyway, I gave it a try and set USB Audio CODEC as the 
output device. Fired up WSJT-X and answered a CQ. It keyed the K3 for about 
five seconds and then the audio started coming out the iMac internal speakers. 
Wonderful. This is the same crud as what was happening before. Not everyone on 
10.11.5 is as lucky as I am, but there are a bunch of folks who’ve been hosed 
by this release. Not sure if you subscribe to the WSJT-X development reflector, 
but the airwaves were burning on this subject over the past several weeks. 
Someone at Apple needs a swift kick in the pants….

Jim, W6JHB




On   Saturday, May 28, 2016, at  Saturday, 8:31 PM, Phil Wheeler 
 wrote:

Adding to what I said below: You do System Preferences > Sound > Input if you 
want your audio input to come from an external USB device (Griffin iMic, 
SignalinkUSB, K3s, etc.).

I am running OS X 10.11.5 and just tested this with an iMic I happened to have 
with me.

73, Phil W7OX

On 5/28/16 8:18 PM, Phil Wheeler wrote:

Jim (and perhaps Dick),

Then go to System Preferences > Sound > Output and select the external USB 
device you want the as the destination for your audio output. You have to do this in 
OS X, not in the application software.

73, Phil W7OX



On 5/28/16 7:49 PM, James Bennett wrote:

Dick,

By any chance have you in the past few weeks upgraded your mac to El Capitan? I 
had a working system (K3, FLDIGI, WSJT-X) and silly me, upgraded to El Capitan 
and a subsequent follow-on update. It has completely broken my digital mode 
operating. The audio is now routed to the internal iMac speakers - no matter 
what I’ve put in the settings of either piece of software. Needless to say, 
with the audio going to the speakers instead of to the K3, it never goes into 
transmit. Apple has really screwed up things this time. I’ve since moved my 
digital operation off of the iMac and over to a Raspberry Pi 3 where WSJT-X is 
working just fine. Havent’ had time to mess with FLDIGI over there yet, but 
maybe next week.

Just a thought…….

Jim, W6JHB



On   Saturday, May 28, 2016, at  Saturday, 12:22 PM, Richard W Hemingway 
  wrote:

Hi,
I am about to give up on my K3S and PSK with my Fldigi on my Mac computer.  I 
am unable to connect either with the SignaLink or with a straight USK 
connection.  Neither will cause the TX light to come on or TX!  I have never  
had t his problem before on any of my Rigs, or before when I owned  a K3.  Joe 
tried your hamlib as well as the Rig Cat settings sent to me from Elecraft.  No 
go.???
If anyone has any bright  ideas please let me know.  This should be keying the 
K3S but it is not.  Have I sset something  that would block t his?
All have a great Memorial weekend, remembering our fallen..
Take care,
Dick. N5XRD


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] OT: Wireless stereo headset recommendations

[Ed]

David

There are a number of headsets on the market that will do the job.  What 
to look for is an inter office device that is used for remote telephone 
service.  Jabra has an extensive line up as does Panasonic.  I have been 
using Jarba for years and had very good luck.  The only problem is you 
won't find any of these that have true stereo.  You can get dual ear 
pieces but they will be monaural not stereo.  I have copied a link to 
the Jarba Web Site. They claim stereo but that isn't correct.  They are 
all monaural. You won't get stereo receive along with a mic. with 
Bluetooth either.  For that setup you will probably have to look for a 
Computer Gaming headset.  The list prices are something that will get 
your attention.  The best I have been able to do is to cruse eBay until 
something reasonable shows up.  I have been using a GN9460 for about 
three years.  It's range is in excess of 600 feet.  Very easy to 
interface to the rig.


http://jb.factoryoutletstore.com/cat/22458/Jabra-GN-Netcom-Wireless-Headsets.html

Ed
K6ED
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] FS: KX-1

[W0FK]

  
Elecraft KX-1 with KXAT1 tuner, KXB3080 board, and updated with the power
amplifier output mod. 80-20 meters, full output, in excellent condition,
little use.  I built the KX-1, Don W3FPR, added the KXB3080 and performed
the power amp mod. $460 shipped CONUS. Lou, W0FK

Please contact me off the list
  
 



-
St. Louis, MO


--
View this message in context: 
http://elecraft.365791.n2.nabble.com/FS-KX-1-tp7618179.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] About to give up

[Bill Frantz]

I found the SignaLink USB VOX based PTT to be very reliable. 
When I am using a SignaLink, I can always know my computer is 
transmitting by hearing the relay click in the SignaLink. When I 
had it connected to the PTT of the K3, it was 100% reliable.


(I have moved to a different sound interface since. I still use 
the SignaLink with my KX3 operating portable.)


73 Bill AE6JV

On 5/28/16 at 4:52 PM, wa6...@gmail.com (Rick WA6NHC) wrote:

I STRONGLY suggest that you do NOT rely on the PTT from the 
SignaLink at all, ever, no way, uh uh, fuggedaboudit, nyet.  
You have to use the full audio drive of the SLUSB to trip it's 
VOX, which is still not reliable.


-
Bill Frantz| The first thing you need when  | Periwinkle
(408)356-8506  | using a perimeter defense is a | 16345 
Englewood Ave
www.pwpconsult.com | perimeter. | Los Gatos, 
CA 95032


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX3: transverter schematic?

[Edward R Cole]

If anyone did not guess I made a typo, below (apparently fingers had 
see too many posts about the KX2).


==snip
Answer is the KX2-2M is very different architecture.  It converts
144-148 to 50-54 MHz unlike other Elecraft transverters that convert
to 28-30 MHz.
==

Of course I meant that ..."the KX3-2M is very different 
architecture.  It converts

144-148 to 50-54 MHz unlike other Elecraft transverters that convert
to 28-30 MHz."



73, Ed - KL7UW
http://www.kl7uw.com
"Kits made by KL7UW"
Dubus Mag business:
dubus...@gmail.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com