Re: [Elecraft] K3 Fault 6 and loss of power control
Hello Pete, This happens to my K3S regularly. After it spent WAY too much time back at the mother ship three years ago without them being able to reproduce the fault (RSA #10260, in case Keith is reading this), I was finally able to narrow down the cause. I can reproduce the fault by going from FL2 to FL3, FL3 to FL4 or by exiting the QRQ mode. This makes me think it may be a firmware problem. I'm running v5.67, the most recent version. I can't figure out how to force a load of an earlier version to see if that cures the problem. Has anyone else experienced this? I can't be the only one. --- 73, Mike Cizek WØVTT -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Pete Smith N4ZR Sent: Wednesday, 6 March, 2024 22:12 To: Elecraft List Subject: [Elecraft] K3 Fault 6 and loss of power control Today I started seeing this in my K3 driving a KPA-1500. It only needs around 30-34 watts to drive it to full power on CW, but when I set the K3's power to that, and everything looks fine, occasionally the K3 displays Fault 6 on its panel and causes the KPA-1500 to fault, displaying 65 watts input on the amp's display and well over 1500 watts on the power bargraph. I can't find any reference to Fault 6 in the manual for the K3 - can anyone clue me in? Is something dying in the K3? -- 73, Pete N4ZR __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K4 Rx is awesome...
N6KR wrote: Of course this is not the way to hold and run a frequency. ***No, you would have to run while doing that, and then your writing would not be legible. Maybe use the Voice Notes app on your cell phone? 浪 --- 73, Mike Cizek WØVTT -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Wayne Burdick Sent: Wednesday, 28 June, 2023 17:03 To: Robert Strickland Cc: Elecraft Reflector Subject: Re: [Elecraft] K4 Rx is awesome... CW is also the only way to go for pedestrian mobile FD, which I did for a couple of hours while hiking on Saturday. Even with a 4' whip and 5 watts I was working almost every station I called. I stopped long enough to log each QSO so my printing would be legible. Of course this is not the way to hold and run a frequency. Wayne N6KR > On Jun 28, 2023, at 1:14 PM, Robert Strickland via Elecraft < > <mailto:elecraft@mailman.qth.net> elecraft@mailman.qth.net> wrote: > > Jim... > > I gave up on all SSB contesting long ago. To my ears and preferences, it's > just a pile of gibberish with maybe one very strong/clear signal every > 10-20Kc. Not worth it. CW is the only way to contest IMHO. While I've never > operated QRP, I suspect that I'm headed in that direction, also. > > ...robert KE2WY > > On 6/25/2023 19:37, Jim Brown wrote: >> On 6/25/2023 7:19 AM, Al Lorona wrote: >>> I went to CW after this and found the operating to be a lot better. >> I gave up on SSB on FD more than ten years ago. Instead, have been doing FD >> QRP with W6GJB and W6JTI. There are still guys who haven't been on the air >> in the year between, and some long pauses after a QSO, but that's the >> exception. >> 73, Jim K9YC __ Elecraft mailing list Home: <http://mailman.qth.net/mailman/listinfo/elecraft> http://mailman.qth.net/mailman/listinfo/elecraft Help: <http://mailman.qth.net/mmfaq.htm> http://mailman.qth.net/mmfaq.htm Post: <mailto:Elecraft@mailman.qth.net> mailto:Elecraft@mailman.qth.net This list hosted by: <http://www.qsl.net> http://www.qsl.net Please help support this email list: <http://www.qsl.net/donate.html> http://www.qsl.net/donate.html Message delivered to <mailto:mgci...@gmail.com> mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Power spike early K3
My K3s has this problem, but it only happens intermittently. When driving the KPA1500, there would be a spike of about 70w. Drive level was between 20 and 25 watts. The K3s spent three months at Elecraft and they could not fix it. I finally discovered two things that caused the power spike: 1. Exiting the CW QRQ mode; either by turning on RIT or by using the menu. 2. Narrowing the passband from XFIL 3 to XFIL 4 (1000 Hz to 400 Hz in my case.), either with the XFIL button or the Width control. These appear to be the only things that cause the power spike. This leads me to believe it's a firmware problem (v 5.67, the most recent). I tried going back to an earlier FW version, but could not figure out how to load it. It doesn't look like there will be any new FW updates for the K3 series. --- 73, Mike Cizek WØVTT -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of N2TK via Elecraft Sent: Saturday, 20 May, 2023 15:51 To: m...@sj2w.se; elecraft@mailman.qth.net Subject: Re: [Elecraft] Power spike early K3 I had the same problem with the K3/KPA1500 combination. I recalibrated the K3. Then I made sure I don't run the K3 at exactly 5W or 50W. The problem has not reappeared.N2TK, Tony -Original Message- From: Mikael Larsmark To: elecraft@mailman.qth.net Sent: Sat, May 20, 2023 3:45 am Subject: [Elecraft] Power spike early K3 Hi, We have an early serial K3 which has got an issue with power spikes. I have done a TX gain calibration without it making a difference. The spike happens mainly when you have changed to a new band and during the first transmission. After that the spike is a lot smaller and not much of an issue. Anybody have any ideas of what this could be because of? It kind of makes it impossible to run a solid state amplifier on the radio and probably not good for the tube amplifiers either. /Mike, SJ2W __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to tony@verizon.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Using KIO3B for digital and AFSK RTTY
Hello Pete, Plug in the USB cable between your K3 and computer. The computer will (should) recognize the K3 sound card as USB Audio CODEC and install drivers automatically. In WSJT-X, select USB Audio CODEC as your microphone and speakers. You can also do radio control through the same USB port, but if you want to do both at the same time you need a port sharing program like LP Bridge. --- 73, Mike Cizek WØVTT -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Pete Smith N4ZR Sent: Wednesday, 3 May, 2023 10:10 To: Elecraft List Subject: [Elecraft] Using KIO3B for digital and AFSK RTTY Is there somewhere online where I can read about how to use the sound card in my KIO3B? I am particularly interested in FT8 and AFSK RTTY, and the KIO3B installation instructions are zero help. -- 73, Pete N4ZR __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] KX1 - SOLD
The KX1 has been sold. Thanks to all who inquired. --- 73, Mike Cizek WØVTT __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] KX1 For Sale
Greetings, Im embarrassed to admit how little I have used this radio. Its been sitting in the box for over ten years. Elecraft KX1 #1797 transceiver in like new condition with: KXAT1 Automatic Antenna Tuner KXB3080 30 and 80 Meter Adapter KXPD1 Plug-In Keyer Paddle Pelican 1060 Case All manuals Purchased at Dayton in May 2007, built in May and June of that year. Recently checked out on the bench and on the air. About 1.5w out with fresh AA batteries; 3~3.5w out on 13.8v. Everything appears to be working correctly and properly HOWEVER since the radio is 16 years old and has been sitting unused for over ten years, I am offering it as is with no guarantees. Pictures available here: https://photos.app.goo.gl/UWT3ga3Rmc1HSgfj7 More pictures and info available on request. Price : $500 including Priority Mail shipping anywhere in the US. Overseas shipping available at buyers expense. Thank you. --- 73, Mike Cizek WØVTT __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] KPA500 Low 40m Output
Greetings, Working on a KPA 500, #2441. All bands except 40m work properly; 40m output is about 125w. Testing into a dummy load: Drive level: ~20w for all bands. Voltage and current levels all seem normal; lower PA current and slightly less voltage drop on 40m. SWR back to exciter (K3s) is 1:1 on all bands Output SWR on the internal meter reads 1:1, even on 40m No fault messages on any band, no smoke, no funny noises. The most obvious (to me) culprit is the 40m low pass filter. I was hoping to find an obviously fried cap or coil, but everything looks OK. A web search shows some folks reporting similar single-band faults, but they all have obviously fried components (usually a cap) on the RF or LPF boards. Is there anything else that could be at fault, other than the LPF circuit? It appears everything else is common to all bands. I'm not sure my test gear is sufficient to check the components in circuit. Thank you. 73, Mike Cizek W0VTT __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Common K3 failure modes??? - K3 Ethernet
I wonder how much of a market there would be for a K3 Ethernet I/O board? What would we need on the other end to control the radio though a built in Ethernet line? 73, Mike Cizek W0VTT -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Dr. William J. Schmidt Sent: Wednesday, 22 June, 2022 11:40 To: elecraft@mailman.qth.net Subject: Re: [Elecraft] [POSSIBLE SPAM] Common K3 failure modes??? I actually designed and build a K3IO "ethernet" replacement KIO3 board...before the USB version was available. I probably have the only "ethernet" K3 on earth. I may revive that card and replace the ethernet stuff with USB parts so that I can fix some of these K3's laying around. I think there is ZERO chance that Elecraft will release parts/ boards/ gerbers for these parts. There is nothing in it for them to do so and may cause maintenance headaches for them. Some of us can pick up the slack though... -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of David Gilbert Sent: Wednesday, June 22, 2022 10:47 AM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] [POSSIBLE SPAM] Common K3 failure modes??? I have also. The K3IO module is pretty fragile, it seems. Of all the requests I've seen here on the reflector over the years for a replacement item, the K3IO tops the list from my memory ... you can't just buy a replacement from Mouser or Digi-Key like you can the input diodes. And when it goes bad, the K3 becomes essentially useless for contesting. I keep saying that Elecraft should pass on the PC board artwork and component specs (I assume that not all of them are standard devices) for key discontinued modules to someone who might be interested in offering replacement as a 3rd party. It's one of my key gripes with Elecraft that they seem to have no interest in doing so. Dave AB7E __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 auto transmit - W7RIP
Hello Rip, That is your computer waking up its com ports. To turn it off, go in to Device Manager and select that port: Properties > Port Settings > Advanced. Uncheck Serial Enumerator. Check Disable Modem Ctrl At Startup. That should do it (for a Windoze machine). ---- 73, Mike Cizek W0VTT -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Rip R Sent: Wednesday, 13 April, 2022 13:59 To: elecraft@mailman.qth.net Subject: [Elecraft] K3 auto transmit - W7RIP My K3 works like a charm and I have never had an issue with it. But recently after I turn the rig on or shortly after I turn it on, it will automatically transmit a series of 5 or 6 cw dashes evenly spaced (good fist) and at about 15 wpm. This will not occur again until the next time the rig is turned on. I do not know why it is doing this, but I would like to know. Ideas? 73s Rip W7RIP __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] End of 3G will not affect your Amateur Radio service
Obviously, Wayne was "too hip for the room". (Since I don't use my K3 in outer space, it operates under 1G) ---- 73, Mike Cizek W0VTT -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of j...@kk9a.com Sent: Wednesday, 16 February, 2022 10:30 To: elecraft@mailman.qth.net Subject: Re: [Elecraft] End of 3G will not affect your Amateur Radio service I think you're missing the point of Wayne's humorist post. I also like 0G on my K3S! John KK9A Gwen Patton NG3P wrote: I have a couple of phones that I just put month-to-month sim cards from Ting into. They're served by T-Mobile. One of my old phones is definitely getting obsoleted out, but that's fine, it's an ancient 2g "Feature Phone" I got from Ebay on a whim. I don't THINK it's a 3g phone...it's one of those Samsung Gravity "Sidekick" style keyboard phones. The only other phone I have one of those cards in is my Inrico 320, and that's safely 4g. I'll probably deactivate the card from the old feature phone rather than pay line charges on it, and buy a new card if I get another phone. I'm not worried about the Gravity, it only cost me about $40 on Ebay anyway, and it was just a whim to get a cool phone I couldn't afford when it was actually popular. -=-=-=-=-=-=-=-=- 73, Gwen, NG3P On Tue, Feb 15, 2022 at 11:17 PM Wayne Burdick wrote: > Major cellular networks are planning to phase out 3G support in favor > of 4G and 5G, starting this month with AT This will render useless millions > of cell phones, home alarm systems, car security systems, and "I've > fallen and I can't get up!" buttons. > > As an Amateur Radio service subscriber, you'll be relieved to know > that > *your* communications service will not be affected. Elecraft is fully > committed to noninterference with the physical laws governing > ionospheric propagation. Further, we promise to never sell any > spectrum without advance > notice. > > 3G has had a good run. But it can't match the longevity of 0G. > > Wayne, N6KR > Service Rep. > Elecraft, Inc. > > --- > Ham radio: The original network, serving you continuously since 1907. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 strange overshoot
Ahoj Petr, I have a similar problem with my K3s. Drive power for the amp is 20 to 25w and the power spike is always around 70w. Elecraft had the radio for three months and claimed they could not reproduce the fault. I discovered later that it only occured when I was in CW QRQ mode and that I could “force” the fault by either exiting QRQ mode or changing to a narrower filter. I sent that info to Elecraft, but they never replied. This happens on all bands except 6m. Thinking it might be a firmware issue, I tried loading an older FW version but have not been able to convince K3 Utility to do that. 73, Mike Cizek WØVTT > On Feb 11, 2022, at 9:45 AM, Petr Ourednik wrote: > > Hi folks, > > so sorry to bother you over here. > I realized strange behavior of my trusty K3 (#778 fully upgraded, loaded, > latest synths installed) > When I tried to exciting KPA500 amp I suffered with strange overshoots during > first dots. > > Symptoms: > - up to 12W from K3 all is ok, over 13W the full scale deflection on KPA500 > appears on first dots > - after 1-2 dots power drops back to expected power based on exciting power > level > - the overshoot appears again after band changing or switching between > OPER/STBY > - 160m-30m are heavily affected, 20m-10m behaves better and it can be driven > up to 18W but overshoot appears too (just slightly to about 600W on LED scale) > > Conditions: > I realized that behavior into antennas with SWR all below 1:1.4 > no SWR > protection activated at all. > The same issue appears into dummy load. > > I will be happy for any kind of ideas or hints where to start...:( > Many thanks in advance. > > 73 - Petr, OK1RP > "Apple & Elecraft freak" > B:http://ok1rp.blogspot.com > -- > What could be easier..? ¯∖_(ツ)_/¯ > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] XV222 For Sale
Greetings, I have an XV222 for sale. Set up to work with 1mW drive from a K3. Testing on the bench, it meets factory specs, but in operation it's a little flaky. It works OK most of the time on CW and SSB, but is not really stable enough for digi mode operation. Whoever built it had no business ever picking up a soldering iron. It has the crystal oven and I have both the assembly and operating manuals. Pictures in a Google Drive folder here: https://photos.app.goo.gl/p7mZY6fgMRf5FgFA6 Asking $200 or best offer. Free shipping in the US via Priority Mail. Overseas shipping (well.international shipping, nobody "overseas" has 222 MHz except Somalia) available at buyer's expense. Thank you. ---- 73, Mike Cizek W0VTT __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] Two XV222 Transverters for Sale
Greetings, I have two Elecraft XV222 transverters for sale. Both have original manuals and have the crystal oven installed. Both are set up to work with 1mW drive from a K3, and both meet factory specs, according to my older but still pretty good test gear. Prices include shipping in the USA. Pictures available on request. XV222 #1 - very well built, works properly, includes the bypass capacitor change (Builder's alert 30 APR 2009) $350 VW222 #2 - works OK most of the time, but looks just awful inside. Whoever built this one had no business ever picking up a soldering iron. It's fine for casual SSB and CW operating, but not stable enough for digi modes. $225 Also - M Squared 222-5WL Yagi. 15 elements on a 24' boom. In good shape with all new fasteners. $150 picked up in southeastern MN, or we can talk about shipping. Thank you. 73, Mike Cizek W0VTT __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] XV222 Mods Question
Greetings, I recently purchased a used XV222 that had some modifications done in the local oscillator circuit. The construction was very sloppy, but transverter works OK most of the time. Power output is adequate with good audio on SSB and receiver sensitivity seems OK. Sometimes the xvtr goes in to parasitic oscillation. I can stop the oscillation by touching certain parts of the case, and it will operate normally for a while. Weird. I cannot find any documentation about the mod on line. It appears that two 2.2 pF caps have been added (on the bottom side of the board) in parallel with C12 (10pF), and the collector of Q1 goes above the board directly to Z4 instead of into its hole in the PCB. Has anyone seen this mod or the reason for it documented anywhere? Thank you. 73, Mike Cizek W0VTT New Kid on VHF __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] XV144 Crystal Oven
Hello David, This was the original product: https://www.isotemp.com/wp-content/uploads/2011/06/Mxx.pdf My XV222 (11 years old) has the M431275 Now made by Taiten and available from Digikey here in the states: https://www.digikey.com/en/products/detail/taitien/M431275/9955528?s=N4IgTCB cDaILYBYDMBGMB2ArCAugXyA Perhaps you can find a distributor in the UK. GL. 73, Mike Cizek W0VTT -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of David Pratt Sent: Saturday, 17 April, 2021 12:41 To: elecraft@mailman.qth.net Subject: [Elecraft] XV144 Crystal Oven I would be pleased to hear from anyone who has a crystal oven for the XV series of transverters. The Elecraft part number is E980076. The oven in my XV144 has gone open circuit. I have attempted to search the Elecraft website for one without success and have even entered an enquiry but have had no response. Any help would be much appreciated. 73 de David G4DMP -- + - - - - - - - - - - - - - - - - + | David M Pratt, Kippax, Leeds. | | Website: http://www.g4dmp.co.uk | + - - - - - - - - - - - - - - - - + __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K2/100 Amp Keying Limits?
Hello Eric, It's in theKPA100 manual, at the back under Specifications: DC relay coil pulled to ground 1A at 200 VDC (do not use with AC-controlled relay) P59 in my book, which I just noticed, comes right after p62. 73, Mike Cizek W0VTT -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of eric norris via Elecraft Sent: Tuesday, 16 March, 2021 21:11 To: Elecraft Reflector Subject: [Elecraft] K2/100 Amp Keying Limits? Can anyone tell me what the external amplifier keying limits are for a K2/100? I'm trying to use an AL811H, which has 14.5V at 10ma on the relay jack. Do I need an external interface? I cannot find the answer in the K2/100 manual. Thanks! 73, Eric WD6DBM __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Copying CW and Pitch
As a bass clef guy my entire life, I have my sidetone set at 300 Hz. Sometimes wish it would go lower. 73, Mike Cizek W0VTT Retired Bass Trombonist -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Dave Fugleberg Sent: Saturday, 13 March, 2021 18:07 To: Elecraft List Subject: Re: [Elecraft] Copying CW and Pitch Jim, that’s an interesting bit of information. Is that the case even for people who have excellent hearing at higher frequencies? In other words, would people with excellent hearing at higher frequencies also benefit from using a lower frequency side tone? On Sat, Mar 13, 2021 at 5:45 PM Jim Brown wrote: > On 3/13/2021 10:48 AM, Sverre Holm (LA3ZA) wrote: > > A CW sidetone pitch of 400 Hz is consistent with what little > > research > there > > is on this. A paper from 1992 says that "/All subjects improved > > their recognition as the frequency was lowered to 500 Hz, some even at 250 > > Hz. > > As a retired designer of large sound systems, I had to learn a lot > about acoustics and psychoacoustics (the science of how humans' > ear/brain interprets what we hear). That science tells us that, like > most of our senses, hearing is logarithmic both with respect to > frequency and loudness. This means that our discrimination of one > frequency as compared to another increases with decreasing frequency. > That is, we are better able to separate signals from each other with > RX pitch set to lower frequencies. > > 73, Jim K9YC > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html Message delivered to > dave.w...@gmail.com > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Suggested Enhancement for KPA-1500
Hello Fred, I use the programmable function keys for this: PF1= ^fc2; PF2= ^fc0; Fan speed 2 is usually enough to keep the heatsink temp below 70C. 73, Mike Cizek W0VTT -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Fred Kemmerer Sent: Friday, 12 March, 2021 07:53 To: elecraft@mailman.qth.net Subject: [Elecraft] Suggested Enhancement for KPA-1500 I have a KPA-1500 amp in our station, and I use it on a daily basis in a remote configuration to operate our station. Fan noise is not an issue here because we are not in the same location as the amplifier. Further, we do mostly digital modes (MSK144, FT8, Q65, etc.) which are high duty cycle. I mostly use the remote app to force the fan speed to a higher level than the factory fan curve to help keep the amp cool. It would be nice if the KPA-1500 FW had a few fan profiles to choose from to help keep the amp cool when running high duty cycle modes. This way, operators such as myself who do a lot of high-duty cycle modes could keep their KPA-1500’s cooler and extend the life of the amplifier. Best and 73, Fred (AB1OC) President, Nashua Area Radio Society ARISS Mentor and Telebridge Station ab...@arrl.net<mailto:ab...@arrl.net> Visit Nashua ARS Website – https://www.n1fd.org<https://www.n1fd.org/> Visit our Blog – https://stationproject.blog<https://stationproject.blog/> __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Now looking for a K3S KTCXO3-1
Greetings - I have a KTCXO3, a Chinese copy, and the standard oscillator. I tested the standard and Chinese ones against WWV at 10 MHz using the Freq Cal mode in WSJT-X over a four hour period. This isn't exactly a laboratory grade test, but is the best I can do. The total error for the Chinese TCXO was 1.26 Hz Total error for the stock oscillator was 0.98 Hz I'll test the KTCXO3 later today. I'm not a math major, but that looks like about 0.1PPM error. Tests were run after the K3s had been on for a few hours. I don't have the tools to measure phase noise. Would having a local with a panadaptor look at my transmitted signal using the different oscillators be sufficient? This is the Chinese oscillator I bought from Ebay: https://www.ebay.com/itm/KTCXO-3-Compatible-Elecraft-K3-TCXO-1-PPM-High-Stab ility-Ref-Osc-Compatible/182814802678?hash=item2a909c82f6:g:7qsAAOSwWr5Z2Y7t 73, Mike Cizek W0VTT -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Mark Goldberg Sent: Wednesday, 10 March, 2021 08:56 To: Elecraft Mailing List Subject: Re: [Elecraft] Now looking for a K3S KTCXO3-1 If the Chinese TCXOs for the K3 are anything like the ones for Kenwood I have measured, they exhibit much higher phase noise. That will result in much increased transmit phase noise. That will interfere with anyone trying to listen close to you in location and frequency. The K3 is a good neighbor, which is one of the reasons it is prized for DXpeditions and Multi Radio contest stations. 73, Mark W7MLG On Wed, Mar 10, 2021, 7:33 AM Wes wrote: > If it mattered to me I would give the Chinese version a shot. > > Wes N7WS > > On 3/10/2021 6:18 AM, Gary Peterson wrote: > > A replacement K3S KTCXO3-1 is no longer available from Elecraft. > > Does > anyone have a stable KTCXO3-1, surplus to their needs, that they would > consider selling? > > Even a standard, plus or minus 5 ppm TCXO might possibly be an > improvement. > > > > There are also some, alleged, KTCXO3-1 oscillator modules for sale > > on > eBay for about 40 bucks. Has anyone had experience with any of these? > > > > Thanks, in advance, for any advice, opinions or admonishments. > > > > Gary, K0CX > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html Message delivered to > marklgoldb...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S KTCXO3-1 possible problem
Hello Gary, Elecraft reported having problems with the TCXOs a while back. Mine isn't very well behaved, either, but it stays within a few Hertz compared to WWV on 10 MHz. 73, Mike Cizek W0VTT -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Gary Peterson Sent: Tuesday, 9 March, 2021 13:40 To: elecraft@mailman.qth.net Subject: [Elecraft] K3S KTCXO3-1 possible problem I have a K3S, purchased factory built, February 2019. This included the 1 ppm TCXO3-1-F option. A few months later, I noticed that SSB signals heard on 50.125.000 MHz all sounded a bit off frequency. Hence, I performed a reference oscillator calibration, using method 2. Because of my relatively short distance to WWV, the variability in the signal strength made its use difficult. Instead, I used a GPS disciplined TCXO as my 10 MHz standard. The GPSDO had been on for several hours before any calibration and the transceiver had been on for, at least, three hours. The frequency display on the K3S was set to 10.000.000 MHz. Beats were displayed on a Weston VU meter, driven by an opamp, connected across the external speaker output. This allows beats to be easily seen, that are less than one per second. The REF CAL as received from the factory was 49.379.766 On 7/10/2019, I changed the REF CAL setting to 49.379.448 (I chalked this change up to possible crystal aging.) On 11/30/2019, the REF CAL setting was changed to 49.379.110 On 3/1/2020 the REF CAL setting was changed to 49.378.926 On 1/16/2021 REF CAL was changed to 49.378.495 On 1/30/2021 REF CAL was changed to 49.378.484 On 2/22/2021 REF CAL was changed to 49.378.508 (the first time the setting has been increased) I have also noticed a change of several Hz in the beat note between the transceiver having been on for half an hour and having been on for three or four hours. This seems odd behavior to me for a high stability, 1 ppm TCXO. The transceiver is in a room, with a temperature of 70, plus or minus, 3 degrees Fahrenheit. There is nothing on top of the transceiver and there is plenty of space below, behind and on either side of the radio. There are no other heat sources near the transceiver. Am I being overly critical, or do you think this is unusual behavior for a KTCXO3-1? I posed this question to Elecraft tech support. The reply did not address my question as to whether this KTCXO3-1 is misbehaving. The reply only said that “We have no KTCXO3-1 and have no orders to restock at this time.” The tech, who replied, also gave me sourcing information for, apparently, the oscillator part on the board. Thanks in advance for any time taken to reply to my post. Gary, KØCX __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Signals wild...signals caged
Well written and fun to read! The chirpy signals are pretty much gone but the key clicks seem to be getting worse. Even some of the newer high-dollar radios are pretty bad. -- 73, Mike Cizek W0VTT -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Wayne Burdick Sent: Thursday, January 28, 2021 12:11 To: Elecraft Reflector Subject: [Elecraft] Signals wild...signals caged My son is an avid birdwatcher. As his understudy, I've learned the names of the birds that hang out in our yard and gather at local wetlands. On a recent walk we saw one of our favorites, an American kestrel, a small raptor that terrorizes lizards and mice in the foothills on both sides of the San Francisco Bay. The bird's coloration is a surprising mix of blue, brown, orange, yellow, and white, adorned with an array of black dots. Finding a kestrel in the wild is like stumbling upon a rare gem, lying on the ground. The bird reminded me that when I was a kid, I often hunted for gems of a different sort: DX. I was a novice, and in the early 1970s, novices were limited to working DX Of The First Kind. CW. Like brightly colored birds, each CW signal arriving from a distant land was unique. Several factors were involved. In those days most ops used bugs or straight keys, so each operator had an identifiable fist. Rigs were not as stable as they are now, yielding timbres with a motley mix of buzz, drift, and chirp. Add fading and noise to the mix, and you had no shortage of audible intrigue. In fact -- trust me on this one -- RST reports haven't always ended with a dependable "9." I once gave out an RST of 332. I'll never forget that poor soul's chaotic whoop, best described as a singular blend of yodel and kazoo. Over time I became something of a CW pathologist, keenly aware of each station's affliction, including my own. These variations were useful. You could tell who you'd already worked. If you were a regular on the novice bands, you'd even get to know fellow travelers by their frequencies, since many, like me, were "rock-bound" -- slaves to a handful of crystals. VFOs were starting to make an appearance in novice gear...but see "chirp," above. Now, in 2021, the chirp is gone. CW signals still have many distinguishing traits, though. These include speed, keying weight, the operator's affectations and favored prosigns, and direction-specific propagation anomalies. Here's where we stretch the central metaphor to just about max. If randomly occurring CW signals on our bands are creatures of the wild, then...are FT8 stations the occupants of an urban zoo? Don't get me wrong: It's a pleasant place, with free tram rides, open 24 hours a day. The diversity of species is unprecedented. But imagine, on a given day, that you've sampled the zoo's exotic offerings, memorized the brochure, bought the t-shirt, and partaken of the sumptuous snack bar. What next? Take a walk on the wild side. Yank the cord and jump off the tram at an unmarked stop. Hop the fence. Work your way down the unpaved trail from the upper mesa to the open savannah, then sit on the ten-foot wall and dangle your feet over the edge. Welcome to the ecosystem of beings who are free to roam. They may be camouflaged, blending into the background. And if you listen carefully, you'll hear a hundred variations on their timeless song...CQ. Wayne N6KR __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Tech Support - I Appreciate the Difficulty...
ONLY 3 weeks? Mine started 7 April and is still going on. The longest delays seem to be between our contact person and the "K3 expert". Eliminating the middle man would help a LOT. K3s #11894 Overdrive Faults -- 73, Mike Cizek W0VTT -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of John Stengrevics Sent: Friday, June 05, 2020 07:30 To: Elecraft Refl Subject: [Elecraft] Tech Support - I Appreciate the Difficulty... of the current situation, but wow. I have been going back and forth with tech support via email (which of course is half the problem) for 3 weeks now. I send an email, it gets passed to the K3S expert, he gets a garbled message, I get a response that makes no sense, I send another message, it gets passed along, I get another response that makes no sense, and on and on ad infinitum. John WA1EAZ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Repair
I dunno...my blinkers seem to work a LOT better after a healthy dose. Although, I understand from a W4 that we don't get the good stuff up north; they keep it all for themselves. -- 73, Mike Cizek W0VTT -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of David Bunte Sent: Friday, March 20, 2020 14:11 To: Bob McGraw K4TAX Cc: elecraft@mailman.qth.net Subject: Re: [Elecraft] Repair Bob - Be carefuk, I understand if you use too much of that kind... your blinkers might not work at all. Dave - K9FN On Fri, Mar 20, 2020 at 2:24 PM Bob McGraw K4TAX wrote: > We have plenty of freshly distilled blinker fluid in TN. > > 73 > > Bob, K4TAX > > On 3/20/2020 12:36 PM, donw4cbs wrote: > > We're out of blinker fluid in Florida. Don, W4CBS Sent from my Sprint > Samsung Galaxy Note9. > > __ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:Elecraft@mailman.qth.net > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > Message delivered to rmcg...@blomand.net > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to dpbu...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] 6m meteor scatter
MSK144 on 50.260 WSJT-X v2.0 More info here: https://physics.princeton.edu/pulsar/k1jt/wsjtx.html You will find the Ping Jockey chatroom very friendly and helpful: https://www.pingjockey.net/cgi-bin/pingtalk -- 73, Mike Cizek WØVTT -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Gordon LaPoint Sent: Wednesday, December 05, 2018 10:44 To: elecraft@mailman.qth.net Subject: Re: [Elecraft] 6m meteor scatter On 6Mtrs what mode and frequency should we be using?? Thanks, Gordon - N1MGO On 12/5/18 11:29 AM, David Olean wrote: > Sporadic meteors are arriving from all sorts of directions, and the > best time for sporadic meteors is at 6 AM local time because that is > the time when your location on Earth is moving into the wind so to > speak. The Earth's travel in its orbit and the forward momentum of > the spinning Earth picks up more meteors at sunrise than when the > opposite is occurring at 6 PM local time. That is the worst time for > sporadic meteors. That being said, you are liable to make a contact at > any time. You are just playing percentages! > > Dave K1WHS -- Gordon - N1MGO __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 Stuck in MCU Load - SOLVED
Many thanks for all the replies. K8ZTT had the correct answer and I am now up and running again. -- 73, Mike Cizek WØVTT From: RIchard Williams [mailto:richarddw1...@yahoo.com] Sent: Saturday, September 29, 2018 19:21 To: mgci...@gmail.com; elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 Stuck in MCU Load IF you are using the USB connection to the computer, you need to either switch to the RS 232 port and use that; OR take the cover off the K3 and move the little slide switch on the KIO3B board to the opposite position. You can then use the USB method. After you have re-installed the firmware, move the switch back to the other position. IF your KIO3B board does not have the small switch, it is an older board and you have to use a RS232 cable. Check with Elecraft, and they will probably switch boards to the newer one with the switch. I had the same issue awhile back. Dick, K8ZTT Sent from Yahoo Mail on Android On Sat, Sep 29, 2018 at 11:45, Mike Cizek W0VTT wrote: Greetings - I appear to have really #@(*)(*% up my K3. While updating the firmware, I accidentally hit either a key on the computer keyboard or one of the mouse buttons. The K3 Utility window "grayed out" and the K3 is stuck in MCU Load, no backlight, TX LED flashing. Setup: Astron 50A PSU; K3 # 2768 with new KIO3B board; direct USB connection to Lenovo Thinkpad running WIN7 Home Premium; K3 Util v 1.16.7.25. Computer and K3 Utility both recognize the COM port; latest FTDI drivers installed. Yes, I know there is supposed to be a cure for this, but it didn't work. I tried: 1. Restarting both the computer and the K3 a few times. 2. Remove & reconnect power supply from K3, hold POWER button to force it into bootloader mode. (which it is already in) 3. Factory reset (power on while holding SHIFT/LO button). Never got the EE INIT message. 4. Uninstall and re-install K3 Utility and try 1-3 again. 5. Uninstall and re-install front panel assembly; try 1-3 again. K3 Utility is still trying to connect and the TX LED is still flashing. Any ideas before I call tech support on Monday? Thanks. -- 73, Mike Cizek WØVTT __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to richarddw1...@yahoo.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3 Stuck in MCU Load
Greetings - I appear to have really #@(*)(*% up my K3. While updating the firmware, I accidentally hit either a key on the computer keyboard or one of the mouse buttons. The K3 Utility window "grayed out" and the K3 is stuck in MCU Load, no backlight, TX LED flashing. Setup: Astron 50A PSU; K3 # 2768 with new KIO3B board; direct USB connection to Lenovo Thinkpad running WIN7 Home Premium; K3 Util v 1.16.7.25. Computer and K3 Utility both recognize the COM port; latest FTDI drivers installed. Yes, I know there is supposed to be a cure for this, but it didn't work. I tried: 1. Restarting both the computer and the K3 a few times. 2. Remove & reconnect power supply from K3, hold POWER button to force it into bootloader mode. (which it is already in) 3. Factory reset (power on while holding SHIFT/LO button). Never got the EE INIT message. 4. Uninstall and re-install K3 Utility and try 1-3 again. 5. Uninstall and re-install front panel assembly; try 1-3 again. K3 Utility is still trying to connect and the TX LED is still flashing. Any ideas before I call tech support on Monday? Thanks. -- 73, Mike Cizek WØVTT __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 and WSJT-X Split operation.
Hello Rick, You really DO need to use some sort of frequency control, either split or fake-it, especially in F mode. When you transmit the lower audio tones, their harmonics and distortion will still be in your audio passband and be transmitted along with the desired tones. The purpose of using proper rig control is to keep the audio tones above 1500 Hz so the harmonics and distortion are out of your transmit passband. -- 73, Mike Cizek WØVTT -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Rick WA6NHC Sent: Friday, June 29, 2018 14:06 To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 and WSJT-X Split operation. I run WSJT-X via HRD rig control (SignaLink audio) for CAT PTT (and VFO) on the K3. I do NOT set WSJT-X for any split. The (sole) VFO doesn't move once set. In everyday FT8, it's fine to let the audio determine actual frequency (the other uses one 'tone', I stay on mine or not, think of it as cross band ops). In hound mode, the change in 'tone' is determined by the program (once ack'ed by the fox); no VFO shift is required. It's been flawless without moving a VFO (except when initially selecting a band or changing to the fox frequency). No added commands to the K3, life is simple. There is a designed lag from keyup to actual generation of tone, which is fine, it lets all the hardware (amps, pre-amps) have time to get 'safe' if needed (the KPA line doesn't require it). Yes, WSJT-X whines every startup in hound configuration that it 'needs' split, but that isn't the case in reality. This setup works, it's simple and simple ROCKS on any day. Rick nhc On 6/29/2018 10:44 AM, Wes Stewart wrote: > Do you have the same mode selected for both VFOs? Give the A -> B a > double tap to be sure. Understand that in Hound mode you need to set > your TX frequency above 1000 Hz. If the Fox calls you he will move > your TX down to his frequency. > > I'm still experiencing a TX delay, which I think is WSJT commanding > the K3 to go Split and then waiting for confirmation. This has been > discussed before. Also, I use VOX and we still don't have VOX > settings remembered by mode, so there is constant fiddling to get the > VOX to activate. > > Wes N7WS > > > On 6/29/2018 9:46 AM, K1RI wrote: >> I too run split FT8 Data A. I cannot get the K3 to transmit in the WSJT >> DXPedition Hound. What am I missing? My IC-7610 works great and I >> would run >> a comparison. >> >> >> Tnx, Bob K1RI >> > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to wa6...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K2 keying mod
Hey Don, Is it true that you can draw the entire K2 schematic from memory? I learn something every time I read one of your posts. Thanks a zillion for all the help you give out on here. We all owe you a beer or three. -- 73, Mike Cizek WØVTT -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Don Wilhelm Sent: Friday, November 03, 2017 08:40 To: Mike Maiorana; elecraft@mailman.qth.net Subject: Re: [Elecraft] K2 keying mod Mike, Order the SMT1B - PIN diode on carrier board p/n E120014 from Elecraft and mount it as shown on page 60 of the latest K2 manual. Note that you also will need to have MCU firmware at 2.04. If yours is lower than that, also order FWK2MCIO. The current firmware is 2.04r, and if you are dealing with a K2 below SN 3000 and have not done the sidetone source change as indicated in the KPA100 or KIO2 instructions, you must add it to use 2.04r because the sidetone source is locked at U8-4. That is the only difference between 2.04P and 2.04r. The rest of the components on the Control Board can be mounted as indicated in the Keying Waveshape Mod documentation. If you do not have that document, send me an off-list email and I can send it to you. I have been installing that mod on all the K2s that I upgrade. 73, Don W3FPR On 11/3/2017 8:56 AM, Mike Maiorana wrote: > I'd like to update my K2 (SN 336) with the keying mod to reduce CW > bandwidth. The doc from Elecraft specifies a PIN diode that is obsolete and > no longer available (5082-3081). > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgci...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] FS: KIO3A; KSYN3; K3STFNR; KFL3A-6K
Greetings, I have the following K3 parts for sale. All were installed in K3 #2786 when I built it in March 2009 and removed as I upgraded. KIO3A - main board is rev A; audio board is rev XD; digi board is rev B. Removed in May 2017. (Note - the two 1 1/4" standoffs are NOT included - Elecraft part # E700119; WWGrainger part # 6RE14, $0.70 for ten of them.) Price $150 shipped USPS Priority Mail in the US. Overseas shipping at buyer's expense. KFL3A-6K AM filter. Removed in April 2015. $75 shipped USPS Priority Mail in the US. Overseas shipping at buyer's expense. TWO KSYN3 synthesizer boards, rev A. Removed in April 2015. TWO K3STFNR shield stiffener kits for the synthesizers; never installed. $150 for all four or offers. Paypal to mgcizek at gmail dot com or Postal money order. Thank you. -- 73, Mike Cizek WØVTT __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] FS: KXV-3 Module
Greetings - I just upgraded to the KXV-3B and would like to sell my old KXV-3. Purchased and installed in March of 2009; KXV3-1 board is Rev B; KXV3-2 board is rev A. Price is $100 including Priority Mail shipping in the United States. Overseas shipping is available at buyer's expense. Paypal to mgcizek at gmail dot com or USPS money order. Thank you. N.B. - this is NOT the new KXV-3B with the second preamp. -- 73, Mike Cizek WØVTT __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K-3 Transmit Problem: no RF Output
Greetings - My K3 has had low output for quite some time, maybe 60-90w depending on the band. I always meant to look into it and fix it someday. Now it has no RF output at all. (Just in time for VK0 and FT/J!) I believe I have traced the problem to two transistors on the LPA board (driver stages), Q4 and Q5, but am not confident they are the only parts at fault. I'm hoping someone else has had the same problem and found the solution. I tried re-seating all the connectors, with a drop of DeoxIt on the pins, and running TX gain cal. 5w and 50w failed immediately, but 100 mW is OK on all bands. KPA-100 was removed, the PA jumper installed between P67A & P67B, and the config menu was set to KPA not installed. Measurements were taken with an old Tek 2465. DC voltages are all correct. Measuring with a scope - I get a nice clean sine wave going in to the LPA board at P71A pin 3. Most bands are 1.2 to 2.2v P-P, but 6m is only 0.6v. The output of Q1 is a little distorted. The output of Q2 varies from 10-25v, depending on the band, and is also a little distorted. Signals at the base of Q4 and Q5 are back down to 3v. Output of Q4 and Q5 is a few mV. Changing the drive control has no affect on signal levels. Is 1 to 2 v P-P the correct drive level at P71A? What is an acceptable variation in power level between different bands? Should the drive control change signal levels here, or does that happen later in the circuit? I am also concerned about the distortion on the wave forms. Q4 and Q5 are available from RF Parts for $5 apiece, so replacing them will likely be my next stap. Thank you. -- 73, Mike Cizek WØVTT __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] EC-1 For Sale
Elecraft EC-1 case - same size as the K-1. No rubber feet. $25.00 plus postage from 21144 - your choice of UPS or USPS. Please reply direct, not to the list. Thank you. 73, Mike W3MC mike at w3mctower dot com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] EC-1 is Sold
Thanks. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K2/100 For Sale
For sale: K-2 #5568 with K160RX, KNB2 and FDIMP built in Nov 06 KPA-100 with upgrade kit built in April 07 KDSP-2 added Aug 08 This is my second K2, has been used very little, and has never been out portable. Pix available on request. Can deliver to Dayton. $1000 shipped in the states via priority mail. Mike Cizek W3MC 410 562-3010 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] WA3WSJ: Just ordered my K3!
Ohboy!! I wonder how many KX-1 pimp out mods Ed will do while waiting for the K-3 to arrive 73 Gr, Mike W3MC Edward R. Breneiser wrote: Hello all, Well I thought about the K3 and compared it to other rigs. I just ordered my K3. Here's what I ordered: K3/100 1 K3 100W Xcvr. (Modular Kit) K3DEP1 K3 50% Deposit (Thanks!) KAT3 1 K3 ATU (Modular Kit) KBPF31 K3 Gen. Cov. RX Module KDVR31 K3 Dig. Voice Recorder KFL3A-2.1K 1 K3 2.1 kHz, 8 pole filter KFL3A-5001 K3 500 Hz, 5 pole filter KUSB 1 Univ. Ser Bus Adapt. MH2 1 Hand Mic. for K2/K3. Looks like it will come in at around $2,526.00. Not a cheap rig, but it should be nice! Ordered 8/20/2007 -- now the wait begins!!! 72, Ed,WA3WSJ ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Pelican case size for KX-1?
What size Pelican case do folks use for the KX-1?? I seem to remember it is the 1060, but its internal height is barely more than the KX-1 itself. Does this provide enough clearance to protect the tuning knob? For people using this case - do you put any foam beneath the KX-1, or just let it sit on the bottom of the case? Thanks. 73, Mike Cizek W3MC [EMAIL PROTECTED] FOC # 1739 HSC # 1849 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] L9 in KX-1
Greetings - I bought a KX-1 at Dayton and am starting to build it. The part I have for L9, 100 uH choke, is a mini size, and the parts list calls for a micro size. Looking at the board, the holes appear to be spaced for a micro sized choke. Should I try to put the mini size in there, or get a micro sized 100 uH choke?? Thanks. 73, Mike Cizek W3MC [EMAIL PROTECTED] FOC # 1739 HSC # 1849 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K-1 for Sale
I've been hit with K-3 fever. Four band (40, 30, 20, 17m) K-1 # 2186 with KAT-1, KBT-1, and FDIMP, set up for 80 kHz tuning range. Excellent condition - used at home a few times, and on portable ops a few times, but I use my K-2s 99% of the time. Have all documentation, and the extra band crystals for 10.0 and 21 MHz. Purchased new on 28 March 06. Would like $525 shipped Priority Mail anywhere in the states. Pictures at http://www.toad.net/~w3mc Also selling one of the K-2/100s with a KAT-100, but think I have a local buyer for that. 73, Mike Cizek W3MC [EMAIL PROTECTED] FOC # 1739 HSC # 1849 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3: internal battery and cooling questions
Better buy two of them, Leigh - make sure you get a properly balanced workout!! Mike Cizek W3MC [EMAIL PROTECTED] FOC # 1739 HSC # 1849 - Original Message - From: wayne burdick [EMAIL PROTECTED] To: Leigh L Klotz, Jr. [EMAIL PROTECTED] Cc: elecraft@mailman.qth.net Sent: Saturday, 28 April, 2007 14:11 Subject: Re: [Elecraft] K3: internal battery and cooling questions No, but it will come with a wrist strap mount for the K3. At only 8 pounds, wrist-mounting of the rig won't kill you (like our 55-pound competitors), but it'll still give you a great upper-body workout :) Wayne Leigh L Klotz, Jr. wrote: Will the fuel cell option come with the hovercraft-mobile mounting kit? I am pretty sure that was promised in the Popular Mechanics article, too. 73, Leigh/WA5ZNU On Sat, 28 Apr 2007 10:34 am, wayne burdick wrote: We're hoping to offer an enclosed [safe!] fuel cell as an internal option someday ;) _ --- http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] More Questions: K3
Hello Lyle - here are a few more questions: 1. How does receive performance compare to the K-2; is the raw performance much better, or are there just more features and flexibility? 2. You said RF Gain is seperate for main sub rcvr? There are 2 AF Gain controls but only one RF - how does this work? 3. Are the roofing filters regular xtal filters - they are in the 8 MHZ IF - and the DSP filtering in the 15 kHz IF? 4. Is TX general coverage or ham bands only? I'm a Navy MARS op. 5. How fast is the QSK compared to the K-2? 6. There are RX ANT IN and OUT jacks on the back panel - what is the OUT jack for - another receiver? Thanks for all the answers this morning. Hope you don't get karpal tunnel from all the typing. 73, Mike Cizek W3MC [EMAIL PROTECTED] FOC # 1739 HSC # 1849 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] KPA100: Rev D manual to build Rev C kit?
I'm in the middle of building the KPA100 I bought last spring, and decided it best to build the board as is, then install the upgrade parts. There are only 16 of them, so it shouldn't add too much time. I built up to page 28 in the manual, and am now waiting for the upgrade kits to arrive. Also ordered one for an older K2/100. GL. 73, Mike Cizek W3MC [EMAIL PROTECTED] FOC # 1739 HSC # 1849 - Original Message - From: LAMB, Dick and Judy [EMAIL PROTECTED] To: Elecraft@mailman.qth.net Sent: Sunday, 18 March, 2007 22:10 Subject: [Elecraft] KPA100: Rev D manual to build Rev C kit? I'm preparing to build a KPA100 from an old kit. My board is marked Rev B, and my manual is Rev C (with Dec 14, 2004 errata sheet). My manual seems to include all mods from the KPA100 Shield Upgrade and the KPA100MODKT. However, my manual does not include all of the changes from the KPA100UPKT (Oct 21, 2006) Upgrade Instructions. I'm finding that integrating these instructions into my manual is very tedious and I'm concerned about making errors. Is there any reason I can't assemble from the latest (Rev D) manual? Thanks Dick, K0KK ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] re: Evaluating antennas
I absolutely and completely agree with Ken, despite having only half of his experience. (30 years, and only two towers - 100' 125' with six rotatable beams). The old fashioned open wire dipole - doublet to our UK brethren - when fed with a proper balanced tuner - is extremely efficient and effective. Read what Maxwell has to say about them in his book Reflections, or look at results with an antenna modelling program. The 80m dipole at 65', when used on the higher bands, will have gain equal to a 3 element yagi in its favored directions. 73, Mike Cizek W3MC [EMAIL PROTECTED] FOC # 1739 HSC # 1849 - Original Message - From: Ken Kopp To: elecraft@mailman.qth.net Sent: Wednesday, 21 February, 2007 19:48 Subject: [Elecraft] Evaluating antennas Given all the discussion about the various antennas I do wire antenna seminars at conventions and hamfests, and usually in some way tell my audience the following: NO antenna is ever high enough! (:-) Many years ago ... 50+ ... I put up (too) many antennas in the quest for the perfect radiator, and I offer the following observation. No antenna should be written off without a long period of evaluation ... perhaps several weeks or more. At the time I was in hot pursuit of something better and would change an antenna too often ... even from one day to the next. I eventually learned that there are many factors that can influence how well antenna will work for you. I didn't understand about the fickle ways of the propogation gods, sunspots, the antenna's surroundings, etc. and that these factors will deternine how your new antenna will work to a greater degree than what kind of antenna it is. I have four 100' towers and some of today's best antennas fed with hardline, but if I had to choose only one it would be the 80M half-wave at 65' that's fed with home-made open wire and a Johnson Matchbox. 73! Ken Kopp - K0PP [EMAIL PROTECTED] or [EMAIL PROTECTED] Ken Kopp - K0PP [EMAIL PROTECTED] or [EMAIL PROTECTED] ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com Mike Cizek W3MC [EMAIL PROTECTED] FOC # 1739 HSC # 1849 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Elecraft CW Net Announcement-musicians
MUCS Michael G Cizek Bass Trombonist US Navy Band, Washington DC http://www.navyband.navy.mil K-2/100, Alpha amp, big beams (trombone players don't do QRP) Mike Cizek W3MC [EMAIL PROTECTED] FOC # 1739 HSC # 1849 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com