Re: [Elecraft] [K3] Low and High Mic gain question
Randy Below are the Macros I use to select the Front microphone (PF1) Rear microphone (FP2). I have an electrict element in a D104 case for the front and a CM500 headset in the rear. You can add eq settings to these if you want different settings for the 2 microphones. Front Mic Name -MicFP Macro - MG020;MN053;DN;DN;SWT11 Assignment - FP1 Rear Mic Name -MicRP Macro - MG006;MN053;DN;DN;UP;SWT11 Assignment - FP2 The above will leave you in the Microphone Select menu. I do that to verify it is correctly gain setting (High-Low). You can add ;MN255 (need the ; to separate) to have the end of the macro exit the menu after SWT11. MGnnn is the mic gain that you use for that microphone MN053 is Mic Sel menu UP DN commands are equivalent to turning the VFO A knob one step. SWT11 is Tap switch 11 [A/B(1)]. This is a toggle. Must exit the Mic Set menu. Error to watch out for -- Pressing FP1 or FP2 twice in a row will give you the wrong gain setting. That is why I make sure to leave the menu up to verify it is set correctly! George AI4VZ -- From: Bill Conkling n...@widomaker.com I think what is needed here are two PF keys, one to set the mic up for FrontPanel, and one for the RearPanel. -Original Message- From: Randy Moore [mailto:wrmoor...@gmail.com] The latest K3 manual implies that the Low and High mic gain settings are kept separately for each of the Front and Rear mic connections, __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] Low and High Mic gain question
George, I was on the verge of developing these same macros, but I got hung up on the toggle of the H L gain setting being a toggle and not knowing what setting it is to start with. Leaving the Menu up seems to be a workable solution to this. I guess once you start using the macros for this, and don't do anything to get out of sync (like using the same macro twice like you say), this should work. Thanks! 73, Randy, KS4L On Thu, Sep 16, 2010 at 11:03 AM, George Jan georgeand...@windstream.netwrote: Randy Below are the Macros I use to select the Front microphone (PF1) Rear microphone (FP2). I have an electrict element in a D104 case for the front and a CM500 headset in the rear. You can add eq settings to these if you want different settings for the 2 microphones. Front Mic Name -MicFP Macro - MG020;MN053;DN;DN;SWT11 Assignment - FP1 Rear Mic Name -MicRP Macro - MG006;MN053;DN;DN;UP;SWT11 Assignment - FP2 The above will leave you in the Microphone Select menu. I do that to verify it is correctly gain setting (High-Low). You can add ;MN255 (need the ; to separate) to have the end of the macro exit the menu after SWT11. MGnnn is the mic gain that you use for that microphone MN053 is Mic Sel menu UP DN commands are equivalent to turning the VFO A knob one step. SWT11 is Tap switch 11 [A/B(1)]. This is a toggle. Must exit the Mic Set menu. Error to watch out for -- Pressing FP1 or FP2 twice in a row will give you the wrong gain setting. That is why I make sure to leave the menu up to verify it is set correctly! George AI4VZ -- From: Bill Conkling n...@widomaker.com I think what is needed here are two PF keys, one to set the mic up for FrontPanel, and one for the RearPanel. -Original Message- From: Randy Moore [mailto:wrmoor...@gmail.com] The latest K3 manual implies that the Low and High mic gain settings are kept separately for each of the Front and Rear mic connections, __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] Low and High Mic gain question
Bill, Bill Conkling schrieb am 15 Sep 2010 um 21:29: I think what is needed here are two PF keys, one to set the mic up for FrontPanel, and one for the RearPanel. Each would make the necessare gain, compression, range, bias and equalization settings for the respective mics. Perhaps someone familiar with the K3 programming could create this and pass it on as a tutorial, or script or whatever for newbies like myself I have created two macros for my microphones, Heil headset rear, Icom SM-8 front. The macro for the Heil is: MN053;DN;DN;UP;SWT11;MN255;MG030; The macro for the Icom is: MN053;DN;DN;SWT11;MN255;MG023; The problem is that the High / Low setting is toggled and not saved seperately for the front and rear microphone. I see two possibilities for the developer to solve it: either keep it seperately for front / rear or create a dedicated code for low and high microphone level. I have also asked for this feature and Wayne's comment was positive. I don't know where it is on the list. 73! de Werner OE9FWV -- Das Problem mit den alten Leuten wird nicht weniger obwohl so viele sterben. Aber es wachsen immer neue nach. Email powered by Pegasus Mail free at http://www.pmail.com Homepage: http://www.qsl.net/oe9fwv/ Fone +43 5522 75013 Fax +43 5522 22505 Mobile +43 664 6340014 Fax-Email Gateway +43 820 220262990 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] [K3] Low and High Mic gain question
The latest K3 manual implies that the Low and High mic gain settings are kept separately for each of the Front and Rear mic connections, but that's not what's happening here with 4.10 firmware. Bias is kept separately. I have a Kenwood hand mic in the front connection and a CM500 headset in the rear - very different mic characteristics! 73, Randy, KS4L __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] Low and High Mic gain question
Hi Randy, I submitted a feature request via the reflector for this in June: http://tinyurl.com/2d8h9sh Andy VK4KY -- View this message in context: http://elecraft.365791.n2.nabble.com/K3-Low-and-High-Mic-gain-question-tp5535878p5535943.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] Low and High Mic gain question
I think what is needed here are two PF keys, one to set the mic up for FrontPanel, and one for the RearPanel. Each would make the necessare gain, compression, range, bias and equalization settings for the respective mics. Perhaps someone familiar with the K3 programming could create this and pass it on as a tutorial, or script or whatever for newbies like myself ...bc nr4c. -Original Message- From: Randy Moore [mailto:wrmoor...@gmail.com] Sent: Wednesday, September 15, 2010 4:11 PM To: Elecraft Discussion List Subject: [Elecraft] [K3] Low and High Mic gain question The latest K3 manual implies that the Low and High mic gain settings are kept separately for each of the Front and Rear mic connections, but that's not what's happening here with 4.10 firmware. Bias is kept separately. I have a Kenwood hand mic in the front connection and a CM500 headset in the rear - very different mic characteristics! 73, Randy, KS4L __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] Low and High Mic gain question
I have a user sequence for DXLab's Commander rig control program (http://www.dxlabsuite.com/) if you use that. It does it all with one sequence (macro). I can email it and you can customize it for your settings. Jim N7US -Original Message- I think what is needed here are two PF keys, one to set the mic up for FrontPanel, and one for the RearPanel. Each would make the necessare gain, compression, range, bias and equalization settings for the respective mics. Perhaps someone familiar with the K3 programming could create this and pass it on as a tutorial, or script or whatever for newbies like myself ...bc nr4c. -Original Message- From: Randy Moore [mailto:wrmoor...@gmail.com] Sent: Wednesday, September 15, 2010 4:11 PM To: Elecraft Discussion List Subject: [Elecraft] [K3] Low and High Mic gain question The latest K3 manual implies that the Low and High mic gain settings are kept separately for each of the Front and Rear mic connections, but that's not what's happening here with 4.10 firmware. Bias is kept separately. I have a Kenwood hand mic in the front connection and a CM500 headset in the rear - very different mic characteristics! 73, Randy, KS4L __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
