Re: [Elecraft] K3 and FLDIGI Question
I'm running fldigi on Linux. You still seem to think I am advocating that the fldigi attenuator be varied during operation, after the K3 mic control was adjusted for the correct ALC indication, as a sort of power control. Of course that's wrong. But again, that's not what I said! I refer to the attenuator merely as an option to set the baseline fldigi output level. This would be a static setting, made in the program setup phase, with no need to touch it again. Rest assured, there are 4-5 bars ALC at all times on my K3 during digital operation, and if I want to change the power level I use the power control! Bob NW8L On Mon, 24 Nov 2014, Joe Subich, W4TV wrote: I'm saying with a properly configured Windows system, there should be no need to adjust the "TX Attenuator" in Fldigi and doing so can only cause instability. As long as each digital program is set for maximum level (maximum digital gain) and the Windows Mixer control for that program is at the same level as the hardware output level for that card, each program will generate the same maximum output level. In this condition, reducing the "TX Attenuator" in fldigi (or "digital output level" in MMTTY, MMVARI, etc.) can only reduce the audio level for that program and cause under drive with the attendant power instability in the K3. 73, ... Joe, W4TV On 2014-11-24 8:53 PM, Bob NW8L wrote: Sigh. I don't see how you read that into my message. I am *not* advocating using the Fldigi attenuator to adjust transmit level in the K3. That ofcourse is done with the K3 power setting, with the K3 input control set for 4-5 bars ALC indicated. I'm saying only that the attenuator can be used to establish the level from flidigi to the soundcard, e.g. to equalize it (if possible) with the output of other programs so that the soundcard and K3 settings don't have to be touched when switching between them. Bob NW8L On Mon, 24 Nov 2014, Joe Subich, W4TV wrote: __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 and FLDIGI Question
I'm saying with a properly configured Windows system, there should be no need to adjust the "TX Attenuator" in Fldigi and doing so can only cause instability. As long as each digital program is set for maximum level (maximum digital gain) and the Windows Mixer control for that program is at the same level as the hardware output level for that card, each program will generate the same maximum output level. In this condition, reducing the "TX Attenuator" in fldigi (or "digital output level" in MMTTY, MMVARI, etc.) can only reduce the audio level for that program and cause under drive with the attendant power instability in the K3. 73, ... Joe, W4TV On 2014-11-24 8:53 PM, Bob NW8L wrote: Sigh. I don't see how you read that into my message. I am *not* advocating using the Fldigi attenuator to adjust transmit level in the K3. That ofcourse is done with the K3 power setting, with the K3 input control set for 4-5 bars ALC indicated. I'm saying only that the attenuator can be used to establish the level from flidigi to the soundcard, e.g. to equalize it (if possible) with the output of other programs so that the soundcard and K3 settings don't have to be touched when switching between them. Bob NW8L On Mon, 24 Nov 2014, Joe Subich, W4TV wrote: On 2014-11-24 11:14 AM, Bob NW8L wrote: Fldigi has a TX level *attenuator* control on the status bar (to the left of the AFC button) that can be used to trim the TX level. It can be used to adjust levels downward to match those of other programs. The K3 *can not* adjust transmit level (power output) by reducing audio drive. If you reduce drive below the ALC threshold, power output will become unstable and "drift". Set your sound card output to a fixed level (typically 60 to 80% of maximum), adjust the K3 Line IN control for four to five bars of ALC, then adjust desired power output using the K3 PWR control. Any other procedure risks unstable power output (low end) or significant distortion (high end). 73, ... Joe, W4TV On 2014-11-24 11:14 AM, Bob NW8L wrote: Fldigi has a TX level *attenuator* control on the status bar (to the left of the AFC button) that can be used to trim the TX level. It can be used to adjust levels downward to match those of other programs. It's not labeled and is often overlooked. Bob NW8L On Sun, 23 Nov 2014, david Moes wrote: Be Carfull you really should have four bars and fifth blinking if its below that you can get some strange fluctuations on the output power. so a compromise between programs is not the best idea. When the K3 is in DATA A mode the mic gain will adjust the level for the line in so adjustment when using different programs is easy. level differences can be a problem with running multiple programs for digital as they seems to have different algorithms and different output levels I no longer use FLdigi and have moved to MMVARI as it has internal TX level adjustment that is independent of the soundcard level. with this I can match the output with the WSJT-X and MMSSTV. I can't seem to find this independent control for FLdigi. I have only tried Coacomodem some time ago but I believe it too has an independent level control that may help in matching levels with other programs although I cant remember if that setting is linked to the windows levels or not I don't believe that WSJT-X has this though. David Moes President: Peterborough Amateur Radio Club. dm...@nexicom.net VE3DVY, VE3SD On 11/23/2014 18:06, James Bennett wrote: John - thanks - that hit the nail on the head for me. The setting I had on my external audio card?s output control was sufficient given the K3?s Mic level that I was using with cocoaModem and WSJT-X. However, as you pointed out, it was not sufficient enough for FLDIGI to ?tickle? the K3. So - I increased the audio card output a bit until I saw the K3?s ALC bars light up, then backed down on the K3?s Mic gain. Now it?s working just fine with FLDIGI, cocoaModem, and WSJT-X. Much appreciated for the replies from both of you - case closed! 73, Jim / W6JHB On Sunday, Nov 23, 2014, at Sunday, 2:13 PM, John Nelson wrote: The same thing happens in my setup, if the audio level from the sound card to the K3 is too low. Nothing will appear in the ALC window, no matter how high I turn up the mic gain. Once establishing a minimum audio level, the ALC will show four bars with the fifth flickering at a mic level of 7. It's very touchy for me to get just right, but I am probably using sub-optimal sound cards. Works fine, though, for all the digital modes. John / W3DN On 11/23/2014 4:34 PM, James Bennett wrote: Hi david - thanks for the reply to my post. Unfortunately, no improvement. I have everything set exactly as you suggest (it was already that way) and the result is the same. I type in some text, press T/R and: the K3 goes into transmit mode, RF flows out the radio to the antenna, but no ALC indication on the K3 ALC meter. I shut down FLDIGI, bring
Re: [Elecraft] K3 and FLDIGI Question
Sigh. I don't see how you read that into my message. I am *not* advocating using the Fldigi attenuator to adjust transmit level in the K3. That ofcourse is done with the K3 power setting, with the K3 input control set for 4-5 bars ALC indicated. I'm saying only that the attenuator can be used to establish the level from flidigi to the soundcard, e.g. to equalize it (if possible) with the output of other programs so that the soundcard and K3 settings don't have to be touched when switching between them. Bob NW8L On Mon, 24 Nov 2014, Joe Subich, W4TV wrote: On 2014-11-24 11:14 AM, Bob NW8L wrote: Fldigi has a TX level *attenuator* control on the status bar (to the left of the AFC button) that can be used to trim the TX level. It can be used to adjust levels downward to match those of other programs. The K3 *can not* adjust transmit level (power output) by reducing audio drive. If you reduce drive below the ALC threshold, power output will become unstable and "drift". Set your sound card output to a fixed level (typically 60 to 80% of maximum), adjust the K3 Line IN control for four to five bars of ALC, then adjust desired power output using the K3 PWR control. Any other procedure risks unstable power output (low end) or significant distortion (high end). 73, ... Joe, W4TV On 2014-11-24 11:14 AM, Bob NW8L wrote: Fldigi has a TX level *attenuator* control on the status bar (to the left of the AFC button) that can be used to trim the TX level. It can be used to adjust levels downward to match those of other programs. It's not labeled and is often overlooked. Bob NW8L On Sun, 23 Nov 2014, david Moes wrote: Be Carfull you really should have four bars and fifth blinking if its below that you can get some strange fluctuations on the output power. so a compromise between programs is not the best idea. When the K3 is in DATA A mode the mic gain will adjust the level for the line in so adjustment when using different programs is easy. level differences can be a problem with running multiple programs for digital as they seems to have different algorithms and different output levels I no longer use FLdigi and have moved to MMVARI as it has internal TX level adjustment that is independent of the soundcard level. with this I can match the output with the WSJT-X and MMSSTV. I can't seem to find this independent control for FLdigi. I have only tried Coacomodem some time ago but I believe it too has an independent level control that may help in matching levels with other programs although I cant remember if that setting is linked to the windows levels or not I don't believe that WSJT-X has this though. David Moes President: Peterborough Amateur Radio Club. dm...@nexicom.net VE3DVY, VE3SD On 11/23/2014 18:06, James Bennett wrote: John - thanks - that hit the nail on the head for me. The setting I had on my external audio card?s output control was sufficient given the K3?s Mic level that I was using with cocoaModem and WSJT-X. However, as you pointed out, it was not sufficient enough for FLDIGI to ?tickle? the K3. So - I increased the audio card output a bit until I saw the K3?s ALC bars light up, then backed down on the K3?s Mic gain. Now it?s working just fine with FLDIGI, cocoaModem, and WSJT-X. Much appreciated for the replies from both of you - case closed! 73, Jim / W6JHB On Sunday, Nov 23, 2014, at Sunday, 2:13 PM, John Nelson wrote: The same thing happens in my setup, if the audio level from the sound card to the K3 is too low. Nothing will appear in the ALC window, no matter how high I turn up the mic gain. Once establishing a minimum audio level, the ALC will show four bars with the fifth flickering at a mic level of 7. It's very touchy for me to get just right, but I am probably using sub-optimal sound cards. Works fine, though, for all the digital modes. John / W3DN On 11/23/2014 4:34 PM, James Bennett wrote: Hi david - thanks for the reply to my post. Unfortunately, no improvement. I have everything set exactly as you suggest (it was already that way) and the result is the same. I type in some text, press T/R and: the K3 goes into transmit mode, RF flows out the radio to the antenna, but no ALC indication on the K3 ALC meter. I shut down FLDIGI, bring up cocoaModem and do EXACTLY the same thing with absolutely no changes, and I get the RF out, but with the fifth ALC bar flickering. Funky, huh? Jim / W6JHB On Sunday, Nov 23, 2014, at Sunday, 6:18 AM, david Moes wrote: Its not normal verify that you have the correct sound card selected in FLdigi and that the levels are set correctly. In the setup under configure sound card first tab "devices" I have port audio set to the sound card for the rig (soundblaster in my case) under "settings" sample rate is native and converter is medium interpolation. and corrections all 0 and third tab "right channel" all buttons are clear unchecked. David Moes VE3DVY, VE3SD On 11/22/
Re: [Elecraft] K3 and FLDIGI Question
I think what you say is understood. but there is a reason to adjust what FLdigi calls TX level. This is to match the output level so it matches other programs this adjustment is independent so it wont effect levels from other programs. At least in the Windows world (Vista, Windows 7, Windows 8/8.1) that adjustment is handled in the Windows Sound Mixer. The "Master" control (hardware) for the output is set to 60 to 80%, the application specific outputs are maintained as separate sub-mixer levels and are generally left at 100% - 100% of the maximum set in the hardware - since application based controls are all relative in the hardware abstraction layer *unless* the particular application is designed to use the sound card in "*exclusive* modes ("Port Audio" is not exclusive). In any case, reducing the audio output of a Windows based digital application to control power output *will* run afoul of the ALC/power control in the K3 (and presumably the KX3). The "attenuator" in Fldigi (and any other digital software) should be left at 100% and the audio drive controlled by the K3 Line In control. 73, ... Joe, W4TV On 2014-11-24 1:14 PM, david Moes wrote: Hi Joe I think what you say is understood. but there is a reason to adjust what FLdigi calls TX level. This is to match the output level so it matches other programs this adjustment is independent so it wont effect levels from other programs.If the output levels of all program can matched ie FLdigi WSJT-X, MMsstv, etc. it simplifies things when moving from one digital program to another by not having to readjust levels every time to achieve the proper setting of four bars fifth blinking. I think if you read the rest of the postings you will understand this need. David Moes President: Peterborough Amateur Radio Club. dm...@nexicom.net VE3DVY, VE3SD On 11/24/2014 11:31, Joe Subich, W4TV wrote: On 2014-11-24 11:14 AM, Bob NW8L wrote: Fldigi has a TX level *attenuator* control on the status bar (to the left of the AFC button) that can be used to trim the TX level. It can be used to adjust levels downward to match those of other programs. The K3 *can not* adjust transmit level (power output) by reducing audio drive. If you reduce drive below the ALC threshold, power output will become unstable and "drift". Set your sound card output to a fixed level (typically 60 to 80% of maximum), adjust the K3 Line IN control for four to five bars of ALC, then adjust desired power output using the K3 PWR control. Any other procedure risks unstable power output (low end) or significant distortion (high end). 73, ... Joe, W4TV On 2014-11-24 11:14 AM, Bob NW8L wrote: Fldigi has a TX level *attenuator* control on the status bar (to the left of the AFC button) that can be used to trim the TX level. It can be used to adjust levels downward to match those of other programs. It's not labeled and is often overlooked. Bob NW8L On Sun, 23 Nov 2014, david Moes wrote: Be Carfull you really should have four bars and fifth blinking if its below that you can get some strange fluctuations on the output power. so a compromise between programs is not the best idea. When the K3 is in DATA A mode the mic gain will adjust the level for the line in so adjustment when using different programs is easy. level differences can be a problem with running multiple programs for digital as they seems to have different algorithms and different output levels I no longer use FLdigi and have moved to MMVARI as it has internal TX level adjustment that is independent of the soundcard level. with this I can match the output with the WSJT-X and MMSSTV. I can't seem to find this independent control for FLdigi. I have only tried Coacomodem some time ago but I believe it too has an independent level control that may help in matching levels with other programs although I cant remember if that setting is linked to the windows levels or not I don't believe that WSJT-X has this though. David Moes President: Peterborough Amateur Radio Club. dm...@nexicom.net VE3DVY, VE3SD On 11/23/2014 18:06, James Bennett wrote: John - thanks - that hit the nail on the head for me. The setting I had on my external audio card?s output control was sufficient given the K3?s Mic level that I was using with cocoaModem and WSJT-X. However, as you pointed out, it was not sufficient enough for FLDIGI to ?tickle? the K3. So - I increased the audio card output a bit until I saw the K3?s ALC bars light up, then backed down on the K3?s Mic gain. Now it?s working just fine with FLDIGI, cocoaModem, and WSJT-X. Much appreciated for the replies from both of you - case closed! 73, Jim / W6JHB On Sunday, Nov 23, 2014, at Sunday, 2:13 PM, John Nelson wrote: The same thing happens in my setup, if the audio level from the sound card to the K3 is too low. Nothing will appear in the ALC window, no matter how high I turn up the mic gain. Once establishing a minimum audio level, the
Re: [Elecraft] K3 and FLDIGI Question
Hi Joe I think what you say is understood. but there is a reason to adjust what FLdigi calls TX level. This is to match the output level so it matches other programs this adjustment is independent so it wont effect levels from other programs.If the output levels of all program can matched ie FLdigi WSJT-X, MMsstv, etc. it simplifies things when moving from one digital program to another by not having to readjust levels every time to achieve the proper setting of four bars fifth blinking. I think if you read the rest of the postings you will understand this need. David Moes President: Peterborough Amateur Radio Club. dm...@nexicom.net VE3DVY, VE3SD On 11/24/2014 11:31, Joe Subich, W4TV wrote: On 2014-11-24 11:14 AM, Bob NW8L wrote: Fldigi has a TX level *attenuator* control on the status bar (to the left of the AFC button) that can be used to trim the TX level. It can be used to adjust levels downward to match those of other programs. The K3 *can not* adjust transmit level (power output) by reducing audio drive. If you reduce drive below the ALC threshold, power output will become unstable and "drift". Set your sound card output to a fixed level (typically 60 to 80% of maximum), adjust the K3 Line IN control for four to five bars of ALC, then adjust desired power output using the K3 PWR control. Any other procedure risks unstable power output (low end) or significant distortion (high end). 73, ... Joe, W4TV On 2014-11-24 11:14 AM, Bob NW8L wrote: Fldigi has a TX level *attenuator* control on the status bar (to the left of the AFC button) that can be used to trim the TX level. It can be used to adjust levels downward to match those of other programs. It's not labeled and is often overlooked. Bob NW8L On Sun, 23 Nov 2014, david Moes wrote: Be Carfull you really should have four bars and fifth blinking if its below that you can get some strange fluctuations on the output power. so a compromise between programs is not the best idea. When the K3 is in DATA A mode the mic gain will adjust the level for the line in so adjustment when using different programs is easy. level differences can be a problem with running multiple programs for digital as they seems to have different algorithms and different output levels I no longer use FLdigi and have moved to MMVARI as it has internal TX level adjustment that is independent of the soundcard level. with this I can match the output with the WSJT-X and MMSSTV. I can't seem to find this independent control for FLdigi. I have only tried Coacomodem some time ago but I believe it too has an independent level control that may help in matching levels with other programs although I cant remember if that setting is linked to the windows levels or not I don't believe that WSJT-X has this though. David Moes President: Peterborough Amateur Radio Club. dm...@nexicom.net VE3DVY, VE3SD On 11/23/2014 18:06, James Bennett wrote: John - thanks - that hit the nail on the head for me. The setting I had on my external audio card?s output control was sufficient given the K3?s Mic level that I was using with cocoaModem and WSJT-X. However, as you pointed out, it was not sufficient enough for FLDIGI to ?tickle? the K3. So - I increased the audio card output a bit until I saw the K3?s ALC bars light up, then backed down on the K3?s Mic gain. Now it?s working just fine with FLDIGI, cocoaModem, and WSJT-X. Much appreciated for the replies from both of you - case closed! 73, Jim / W6JHB On Sunday, Nov 23, 2014, at Sunday, 2:13 PM, John Nelson wrote: The same thing happens in my setup, if the audio level from the sound card to the K3 is too low. Nothing will appear in the ALC window, no matter how high I turn up the mic gain. Once establishing a minimum audio level, the ALC will show four bars with the fifth flickering at a mic level of 7. It's very touchy for me to get just right, but I am probably using sub-optimal sound cards. Works fine, though, for all the digital modes. John / W3DN On 11/23/2014 4:34 PM, James Bennett wrote: Hi david - thanks for the reply to my post. Unfortunately, no improvement. I have everything set exactly as you suggest (it was already that way) and the result is the same. I type in some text, press T/R and: the K3 goes into transmit mode, RF flows out the radio to the antenna, but no ALC indication on the K3 ALC meter. I shut down FLDIGI, bring up cocoaModem and do EXACTLY the same thing with absolutely no changes, and I get the RF out, but with the fifth ALC bar flickering. Funky, huh? Jim / W6JHB On Sunday, Nov 23, 2014, at Sunday, 6:18 AM, david Moes wrote: Its not normal verify that you have the correct sound card selected in FLdigi and that the levels are set correctly. In the setup under configure sound card first tab "devices" I have port audio set to the sound card for the rig (soundblaster in my case) under "settings" sample rate is native and conve
Re: [Elecraft] K3 and FLDIGI Question
On 2014-11-24 11:14 AM, Bob NW8L wrote: Fldigi has a TX level *attenuator* control on the status bar (to the left of the AFC button) that can be used to trim the TX level. It can be used to adjust levels downward to match those of other programs. The K3 *can not* adjust transmit level (power output) by reducing audio drive. If you reduce drive below the ALC threshold, power output will become unstable and "drift". Set your sound card output to a fixed level (typically 60 to 80% of maximum), adjust the K3 Line IN control for four to five bars of ALC, then adjust desired power output using the K3 PWR control. Any other procedure risks unstable power output (low end) or significant distortion (high end). 73, ... Joe, W4TV On 2014-11-24 11:14 AM, Bob NW8L wrote: Fldigi has a TX level *attenuator* control on the status bar (to the left of the AFC button) that can be used to trim the TX level. It can be used to adjust levels downward to match those of other programs. It's not labeled and is often overlooked. Bob NW8L On Sun, 23 Nov 2014, david Moes wrote: Be Carfull you really should have four bars and fifth blinking if its below that you can get some strange fluctuations on the output power. so a compromise between programs is not the best idea. When the K3 is in DATA A mode the mic gain will adjust the level for the line in so adjustment when using different programs is easy. level differences can be a problem with running multiple programs for digital as they seems to have different algorithms and different output levels I no longer use FLdigi and have moved to MMVARI as it has internal TX level adjustment that is independent of the soundcard level. with this I can match the output with the WSJT-X and MMSSTV. I can't seem to find this independent control for FLdigi. I have only tried Coacomodem some time ago but I believe it too has an independent level control that may help in matching levels with other programs although I cant remember if that setting is linked to the windows levels or not I don't believe that WSJT-X has this though. David Moes President: Peterborough Amateur Radio Club. dm...@nexicom.net VE3DVY, VE3SD On 11/23/2014 18:06, James Bennett wrote: John - thanks - that hit the nail on the head for me. The setting I had on my external audio card?s output control was sufficient given the K3?s Mic level that I was using with cocoaModem and WSJT-X. However, as you pointed out, it was not sufficient enough for FLDIGI to ?tickle? the K3. So - I increased the audio card output a bit until I saw the K3?s ALC bars light up, then backed down on the K3?s Mic gain. Now it?s working just fine with FLDIGI, cocoaModem, and WSJT-X. Much appreciated for the replies from both of you - case closed! 73, Jim / W6JHB On Sunday, Nov 23, 2014, at Sunday, 2:13 PM, John Nelson wrote: The same thing happens in my setup, if the audio level from the sound card to the K3 is too low. Nothing will appear in the ALC window, no matter how high I turn up the mic gain. Once establishing a minimum audio level, the ALC will show four bars with the fifth flickering at a mic level of 7. It's very touchy for me to get just right, but I am probably using sub-optimal sound cards. Works fine, though, for all the digital modes. John / W3DN On 11/23/2014 4:34 PM, James Bennett wrote: Hi david - thanks for the reply to my post. Unfortunately, no improvement. I have everything set exactly as you suggest (it was already that way) and the result is the same. I type in some text, press T/R and: the K3 goes into transmit mode, RF flows out the radio to the antenna, but no ALC indication on the K3 ALC meter. I shut down FLDIGI, bring up cocoaModem and do EXACTLY the same thing with absolutely no changes, and I get the RF out, but with the fifth ALC bar flickering. Funky, huh? Jim / W6JHB On Sunday, Nov 23, 2014, at Sunday, 6:18 AM, david Moes wrote: Its not normal verify that you have the correct sound card selected in FLdigi and that the levels are set correctly. In the setup under configure sound card first tab "devices" I have port audio set to the sound card for the rig (soundblaster in my case) under "settings" sample rate is native and converter is medium interpolation. and corrections all 0 and third tab "right channel" all buttons are clear unchecked. David Moes VE3DVY, VE3SD On 11/22/2014 17:15, James Bennett wrote: I?ve been using cocoaModem on my iMac for PSK31 QSO?s. Also, I use WSJT-X for JT65 and JT9. Recently downloaded FLDIGI v 3.22.01 and gave it a try. It works, but?.. When I transmit, I get absolutely no indication of RF being sent. The K3 goes into transmit mode, but I get no ALC action on the K3 meter. I know I?m getting RF out because (1) my KPA500 (in standby mode) is showing 30 watts, and (2) I?ve had several QSO?s on PSK31. If I bring up cocoaModem and transmit, I get the ALC action that I?m used to seeing: the fifth bar fli
Re: [Elecraft] K3 and FLDIGI Question
Fldigi has a TX level *attenuator* control on the status bar (to the left of the AFC button) that can be used to trim the TX level. It can be used to adjust levels downward to match those of other programs. It's not labeled and is often overlooked. Bob NW8L On Sun, 23 Nov 2014, david Moes wrote: Be Carfull you really should have four bars and fifth blinking if its below that you can get some strange fluctuations on the output power. so a compromise between programs is not the best idea. When the K3 is in DATA A mode the mic gain will adjust the level for the line in so adjustment when using different programs is easy. level differences can be a problem with running multiple programs for digital as they seems to have different algorithms and different output levels I no longer use FLdigi and have moved to MMVARI as it has internal TX level adjustment that is independent of the soundcard level. with this I can match the output with the WSJT-X and MMSSTV. I can't seem to find this independent control for FLdigi. I have only tried Coacomodem some time ago but I believe it too has an independent level control that may help in matching levels with other programs although I cant remember if that setting is linked to the windows levels or not I don't believe that WSJT-X has this though. David Moes President: Peterborough Amateur Radio Club. dm...@nexicom.net VE3DVY, VE3SD On 11/23/2014 18:06, James Bennett wrote: John - thanks - that hit the nail on the head for me. The setting I had on my external audio card?s output control was sufficient given the K3?s Mic level that I was using with cocoaModem and WSJT-X. However, as you pointed out, it was not sufficient enough for FLDIGI to ?tickle? the K3. So - I increased the audio card output a bit until I saw the K3?s ALC bars light up, then backed down on the K3?s Mic gain. Now it?s working just fine with FLDIGI, cocoaModem, and WSJT-X. Much appreciated for the replies from both of you - case closed! 73, Jim / W6JHB On Sunday, Nov 23, 2014, at Sunday, 2:13 PM, John Nelson wrote: The same thing happens in my setup, if the audio level from the sound card to the K3 is too low. Nothing will appear in the ALC window, no matter how high I turn up the mic gain. Once establishing a minimum audio level, the ALC will show four bars with the fifth flickering at a mic level of 7. It's very touchy for me to get just right, but I am probably using sub-optimal sound cards. Works fine, though, for all the digital modes. John / W3DN On 11/23/2014 4:34 PM, James Bennett wrote: Hi david - thanks for the reply to my post. Unfortunately, no improvement. I have everything set exactly as you suggest (it was already that way) and the result is the same. I type in some text, press T/R and: the K3 goes into transmit mode, RF flows out the radio to the antenna, but no ALC indication on the K3 ALC meter. I shut down FLDIGI, bring up cocoaModem and do EXACTLY the same thing with absolutely no changes, and I get the RF out, but with the fifth ALC bar flickering. Funky, huh? Jim / W6JHB On Sunday, Nov 23, 2014, at Sunday, 6:18 AM, david Moes wrote: Its not normal verify that you have the correct sound card selected in FLdigi and that the levels are set correctly. In the setup under configure sound card first tab "devices" I have port audio set to the sound card for the rig (soundblaster in my case) under "settings" sample rate is native and converter is medium interpolation. and corrections all 0 and third tab "right channel" all buttons are clear unchecked. David Moes VE3DVY, VE3SD On 11/22/2014 17:15, James Bennett wrote: I?ve been using cocoaModem on my iMac for PSK31 QSO?s. Also, I use WSJT-X for JT65 and JT9. Recently downloaded FLDIGI v 3.22.01 and gave it a try. It works, but?.. When I transmit, I get absolutely no indication of RF being sent. The K3 goes into transmit mode, but I get no ALC action on the K3 meter. I know I?m getting RF out because (1) my KPA500 (in standby mode) is showing 30 watts, and (2) I?ve had several QSO?s on PSK31. If I bring up cocoaModem and transmit, I get the ALC action that I?m used to seeing: the fifth bar flickering. Same thing with WSJT-X. But for some reason, when I transmit with FLDIGI - nada, zip, zero indication. Is this ?normal?? If so, how would one ever set audio levels w/o having any indication of audio actually flowing? What do I have set wrong? Thanks, Jim / W6JHB __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to dm...@nexicom.net __ Elecraft mailing list Home: http://mail
Re: [Elecraft] K3 and FLDIGI Question
Be Carfull you really should have four bars and fifth blinking if its below that you can get some strange fluctuations on the output power. so a compromise between programs is not the best idea. When the K3 is in DATA A mode the mic gain will adjust the level for the line in so adjustment when using different programs is easy. level differences can be a problem with running multiple programs for digital as they seems to have different algorithms and different output levels I no longer use FLdigi and have moved to MMVARI as it has internal TX level adjustment that is independent of the soundcard level. with this I can match the output with the WSJT-X and MMSSTV. I can't seem to find this independent control for FLdigi. I have only tried Coacomodem some time ago but I believe it too has an independent level control that may help in matching levels with other programs although I cant remember if that setting is linked to the windows levels or not I don't believe that WSJT-X has this though. David Moes President: Peterborough Amateur Radio Club. dm...@nexicom.net VE3DVY, VE3SD On 11/23/2014 18:06, James Bennett wrote: John - thanks - that hit the nail on the head for me. The setting I had on my external audio card’s output control was sufficient given the K3’s Mic level that I was using with cocoaModem and WSJT-X. However, as you pointed out, it was not sufficient enough for FLDIGI to “tickle” the K3. So - I increased the audio card output a bit until I saw the K3’s ALC bars light up, then backed down on the K3’s Mic gain. Now it’s working just fine with FLDIGI, cocoaModem, and WSJT-X. Much appreciated for the replies from both of you - case closed! 73, Jim / W6JHB On Sunday, Nov 23, 2014, at Sunday, 2:13 PM, John Nelson wrote: The same thing happens in my setup, if the audio level from the sound card to the K3 is too low. Nothing will appear in the ALC window, no matter how high I turn up the mic gain. Once establishing a minimum audio level, the ALC will show four bars with the fifth flickering at a mic level of 7. It's very touchy for me to get just right, but I am probably using sub-optimal sound cards. Works fine, though, for all the digital modes. John / W3DN On 11/23/2014 4:34 PM, James Bennett wrote: Hi david - thanks for the reply to my post. Unfortunately, no improvement. I have everything set exactly as you suggest (it was already that way) and the result is the same. I type in some text, press T/R and: the K3 goes into transmit mode, RF flows out the radio to the antenna, but no ALC indication on the K3 ALC meter. I shut down FLDIGI, bring up cocoaModem and do EXACTLY the same thing with absolutely no changes, and I get the RF out, but with the fifth ALC bar flickering. Funky, huh? Jim / W6JHB On Sunday, Nov 23, 2014, at Sunday, 6:18 AM, david Moes wrote: Its not normal verify that you have the correct sound card selected in FLdigi and that the levels are set correctly. In the setup under configure sound card first tab "devices" I have port audio set to the sound card for the rig (soundblaster in my case) under "settings" sample rate is native and converter is medium interpolation. and corrections all 0 and third tab "right channel" all buttons are clear unchecked. David Moes VE3DVY, VE3SD On 11/22/2014 17:15, James Bennett wrote: I’ve been using cocoaModem on my iMac for PSK31 QSO’s. Also, I use WSJT-X for JT65 and JT9. Recently downloaded FLDIGI v 3.22.01 and gave it a try. It works, but….. When I transmit, I get absolutely no indication of RF being sent. The K3 goes into transmit mode, but I get no ALC action on the K3 meter. I know I’m getting RF out because (1) my KPA500 (in standby mode) is showing 30 watts, and (2) I’ve had several QSO’s on PSK31. If I bring up cocoaModem and transmit, I get the ALC action that I’m used to seeing: the fifth bar flickering. Same thing with WSJT-X. But for some reason, when I transmit with FLDIGI - nada, zip, zero indication. Is this “normal”? If so, how would one ever set audio levels w/o having any indication of audio actually flowing? What do I have set wrong? Thanks, Jim / W6JHB __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to dm...@nexicom.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to w6...@me.com
Re: [Elecraft] K3 and FLDIGI Question
John - thanks - that hit the nail on the head for me. The setting I had on my external audio card’s output control was sufficient given the K3’s Mic level that I was using with cocoaModem and WSJT-X. However, as you pointed out, it was not sufficient enough for FLDIGI to “tickle” the K3. So - I increased the audio card output a bit until I saw the K3’s ALC bars light up, then backed down on the K3’s Mic gain. Now it’s working just fine with FLDIGI, cocoaModem, and WSJT-X. Much appreciated for the replies from both of you - case closed! 73, Jim / W6JHB > On Sunday, Nov 23, 2014, at Sunday, 2:13 PM, John Nelson > wrote: > > The same thing happens in my setup, if the audio level from the sound card to > the K3 is too low. Nothing will appear in the ALC window, no matter how high > I turn up the mic gain. Once establishing a minimum audio level, the ALC > will show four bars with the fifth flickering at a mic level of 7. It's very > touchy for me to get just right, but I am probably using sub-optimal sound > cards. Works fine, though, for all the digital modes. > > John / W3DN > > > On 11/23/2014 4:34 PM, James Bennett wrote: >> Hi david - thanks for the reply to my post. >> >> Unfortunately, no improvement. I have everything set exactly as you suggest >> (it was already that way) and the result is the same. I type in some text, >> press T/R and: the K3 goes into transmit mode, RF flows out the radio to the >> antenna, but no ALC indication on the K3 ALC meter. I shut down FLDIGI, >> bring up cocoaModem and do EXACTLY the same thing with absolutely no >> changes, and I get the RF out, but with the fifth ALC bar flickering. Funky, >> huh? >> >> Jim / W6JHB >> >> >>> On Sunday, Nov 23, 2014, at Sunday, 6:18 AM, david Moes >>> wrote: >>> >>> Its not normal verify that you have the correct sound card selected in >>> FLdigi and that the levels are set correctly. >>> >>> In the setup under configure sound card first tab >>> "devices" I have port audio set to the sound card for the rig >>> (soundblaster in my case) >>> under "settings" sample rate is native and converter is medium >>> interpolation. and corrections all 0 and >>> third tab "right channel" all buttons are clear unchecked. >>> >>> David Moes >>> VE3DVY, VE3SD >>> >>> On 11/22/2014 17:15, James Bennett wrote: I’ve been using cocoaModem on my iMac for PSK31 QSO’s. Also, I use WSJT-X for JT65 and JT9. Recently downloaded FLDIGI v 3.22.01 and gave it a try. It works, but….. When I transmit, I get absolutely no indication of RF being sent. The K3 goes into transmit mode, but I get no ALC action on the K3 meter. I know I’m getting RF out because (1) my KPA500 (in standby mode) is showing 30 watts, and (2) I’ve had several QSO’s on PSK31. If I bring up cocoaModem and transmit, I get the ALC action that I’m used to seeing: the fifth bar flickering. Same thing with WSJT-X. But for some reason, when I transmit with FLDIGI - nada, zip, zero indication. Is this “normal”? If so, how would one ever set audio levels w/o having any indication of audio actually flowing? What do I have set wrong? Thanks, Jim / W6JHB __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to dm...@nexicom.net >>> __ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:Elecraft@mailman.qth.net >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >>> Message delivered to w6...@me.com >> __ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to j...@happyvalleybiz.com > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to w6...@me.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailm
Re: [Elecraft] K3 and FLDIGI Question
The same thing happens in my setup, if the audio level from the sound card to the K3 is too low. Nothing will appear in the ALC window, no matter how high I turn up the mic gain. Once establishing a minimum audio level, the ALC will show four bars with the fifth flickering at a mic level of 7. It's very touchy for me to get just right, but I am probably using sub-optimal sound cards. Works fine, though, for all the digital modes. John / W3DN On 11/23/2014 4:34 PM, James Bennett wrote: Hi david - thanks for the reply to my post. Unfortunately, no improvement. I have everything set exactly as you suggest (it was already that way) and the result is the same. I type in some text, press T/R and: the K3 goes into transmit mode, RF flows out the radio to the antenna, but no ALC indication on the K3 ALC meter. I shut down FLDIGI, bring up cocoaModem and do EXACTLY the same thing with absolutely no changes, and I get the RF out, but with the fifth ALC bar flickering. Funky, huh? Jim / W6JHB On Sunday, Nov 23, 2014, at Sunday, 6:18 AM, david Moes wrote: Its not normal verify that you have the correct sound card selected in FLdigi and that the levels are set correctly. In the setup under configure sound card first tab "devices" I have port audio set to the sound card for the rig (soundblaster in my case) under "settings" sample rate is native and converter is medium interpolation. and corrections all 0 and third tab "right channel" all buttons are clear unchecked. David Moes VE3DVY, VE3SD On 11/22/2014 17:15, James Bennett wrote: I’ve been using cocoaModem on my iMac for PSK31 QSO’s. Also, I use WSJT-X for JT65 and JT9. Recently downloaded FLDIGI v 3.22.01 and gave it a try. It works, but….. When I transmit, I get absolutely no indication of RF being sent. The K3 goes into transmit mode, but I get no ALC action on the K3 meter. I know I’m getting RF out because (1) my KPA500 (in standby mode) is showing 30 watts, and (2) I’ve had several QSO’s on PSK31. If I bring up cocoaModem and transmit, I get the ALC action that I’m used to seeing: the fifth bar flickering. Same thing with WSJT-X. But for some reason, when I transmit with FLDIGI - nada, zip, zero indication. Is this “normal”? If so, how would one ever set audio levels w/o having any indication of audio actually flowing? What do I have set wrong? Thanks, Jim / W6JHB __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to dm...@nexicom.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to w6...@me.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to j...@happyvalleybiz.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 and FLDIGI Question
Hi david - thanks for the reply to my post. Unfortunately, no improvement. I have everything set exactly as you suggest (it was already that way) and the result is the same. I type in some text, press T/R and: the K3 goes into transmit mode, RF flows out the radio to the antenna, but no ALC indication on the K3 ALC meter. I shut down FLDIGI, bring up cocoaModem and do EXACTLY the same thing with absolutely no changes, and I get the RF out, but with the fifth ALC bar flickering. Funky, huh? Jim / W6JHB > On Sunday, Nov 23, 2014, at Sunday, 6:18 AM, david Moes > wrote: > > Its not normal verify that you have the correct sound card selected in > FLdigi and that the levels are set correctly. > > In the setup under configure sound card first tab > "devices" I have port audio set to the sound card for the rig (soundblaster > in my case) > under "settings" sample rate is native and converter is medium interpolation. > and corrections all 0 and > third tab "right channel" all buttons are clear unchecked. > > David Moes > VE3DVY, VE3SD > > On 11/22/2014 17:15, James Bennett wrote: >> I’ve been using cocoaModem on my iMac for PSK31 QSO’s. Also, I use WSJT-X >> for JT65 and JT9. Recently downloaded FLDIGI v 3.22.01 and gave it a try. It >> works, but….. >> >> When I transmit, I get absolutely no indication of RF being sent. The K3 >> goes into transmit mode, but I get no ALC action on the K3 meter. I know I’m >> getting RF out because (1) my KPA500 (in standby mode) is showing 30 watts, >> and (2) I’ve had several QSO’s on PSK31. If I bring up cocoaModem and >> transmit, I get the ALC action that I’m used to seeing: the fifth bar >> flickering. Same thing with WSJT-X. But for some reason, when I transmit >> with FLDIGI - nada, zip, zero indication. >> >> Is this “normal”? If so, how would one ever set audio levels w/o having any >> indication of audio actually flowing? What do I have set wrong? >> >> Thanks, Jim / W6JHB >> __ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to dm...@nexicom.net > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to w6...@me.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 and FLDIGI Question
Its not normal verify that you have the correct sound card selected in FLdigi and that the levels are set correctly. In the setup under configure sound card first tab "devices" I have port audio set to the sound card for the rig (soundblaster in my case) under "settings" sample rate is native and converter is medium interpolation. and corrections all 0 and third tab "right channel" all buttons are clear unchecked. David Moes VE3DVY, VE3SD On 11/22/2014 17:15, James Bennett wrote: I’ve been using cocoaModem on my iMac for PSK31 QSO’s. Also, I use WSJT-X for JT65 and JT9. Recently downloaded FLDIGI v 3.22.01 and gave it a try. It works, but….. When I transmit, I get absolutely no indication of RF being sent. The K3 goes into transmit mode, but I get no ALC action on the K3 meter. I know I’m getting RF out because (1) my KPA500 (in standby mode) is showing 30 watts, and (2) I’ve had several QSO’s on PSK31. If I bring up cocoaModem and transmit, I get the ALC action that I’m used to seeing: the fifth bar flickering. Same thing with WSJT-X. But for some reason, when I transmit with FLDIGI - nada, zip, zero indication. Is this “normal”? If so, how would one ever set audio levels w/o having any indication of audio actually flowing? What do I have set wrong? Thanks, Jim / W6JHB __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to dm...@nexicom.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3 and FLDIGI Question
I’ve been using cocoaModem on my iMac for PSK31 QSO’s. Also, I use WSJT-X for JT65 and JT9. Recently downloaded FLDIGI v 3.22.01 and gave it a try. It works, but….. When I transmit, I get absolutely no indication of RF being sent. The K3 goes into transmit mode, but I get no ALC action on the K3 meter. I know I’m getting RF out because (1) my KPA500 (in standby mode) is showing 30 watts, and (2) I’ve had several QSO’s on PSK31. If I bring up cocoaModem and transmit, I get the ALC action that I’m used to seeing: the fifth bar flickering. Same thing with WSJT-X. But for some reason, when I transmit with FLDIGI - nada, zip, zero indication. Is this “normal”? If so, how would one ever set audio levels w/o having any indication of audio actually flowing? What do I have set wrong? Thanks, Jim / W6JHB __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com