Re: [Elecraft] P3 Span settings

2016-02-17 Thread Clay Autery 
I apologize.  I must have missed that part...  

__
Clay Autery, KG5LKV
(318) 518-1389

On 2/17/2016 4:31 PM, Dave Cole wrote:
> Hi,
> Yes, the ";" is a slight delay...  However I believe this issue goes
> beyond a simple delay...  
>
> As I mentioned in my last post, I have a set of macros, where the last
> macro crashes the first macro in the string...  In my mind, that pretty
> well eliminates all timing issues...

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] P3 Span settings

2016-02-17 Thread Dave Cole 
Hi,
Yes, the ";" is a slight delay...  However I believe this issue goes
beyond a simple delay...  

As I mentioned in my last post, I have a set of macros, where the last
macro crashes the first macro in the string...  In my mind, that pretty
well eliminates all timing issues...
-- 
73's, and thanks,
Dave

For software/hardware reviews see:
http://www.nk7z.net

For MixW support see:
https://groups.yahoo.com/neo/groups/mixw/info

For SSTV help see:
http://groups.yahoo.com/neo/groups/MM-SSTV/info



On Wed, 2016-02-17 at 15:22 -0600, Clay Autery wrote:
> I haven't looked into the command language for the P3 in depth yet...
> 
> Is there a command for a "time delay".  It would appear that you need
> to
> insert a time delay in between each individual command to allow the
> unit
> time to respond to each step.
> 
> Just a SWAG...  (If the command doesn't exist, it looks like a prime
> candidate for the next Firmware iteration)
> 
> __
> Clay Autery, KG5LKV
> (318) 518-1389
> 
> On 2/17/2016 2:46 PM, Dave Cole wrote:
> > Hello Tim and Gary,
> > 
> > I have done extensive testing in trying to get a macro to perform
> > this
> > exact behavior...  
> > 
> > I do not believe "currently" there is a way to make this happen via
> > macro commands.  
> > 
> > If you perform the needed steps by hand, with lots of space between
> > commands, it works, if you then place the exact same commands in a
> > macro it fails.
> > 
> > I tested by placing each command below in its own macro key using
> > the
> > P3 Macro tester software included with the P3 utility.  Here is an
> > example:
> > 
> > I have a DX station at 14.010, and I want to move 14.010 to the
> > left
> > edge of the P3, showing the upper 5 KHz ra
> > 
> > 
> > Macro 1:
> > #SPN000100; 
> > Sets span to plus and minus 10 KHz.
> > 
> > Macro 2:
> > UP7;
> > Moves K3 up 5 KHz.
> > 
> > Macro 3:
> > #FXT1;  
> > Places the P3 in sticky mode, (Fixed Tune), locking the transmit
> > frequency to the center of the P3 screen.
> > 
> > Macro 4:
> > DN7;
> > Moves the K3 down 5, dragging the transmit freq down with it, and
> > putting the transmit freq on the left edge of the P3, exposing the
> > upper 10 KHz of the signals on the P3.
> > 
> > If I then fire them one at a time, everything works as expected,
> > the
> > transmit frequency is on the lower left edge for an up split.
> > 
> > If I place them in a single macro, it fails, every time...
> > 
> > 
> > 73's, and thanks,
> > Dave
> > 
> > For software/hardware reviews see:
> > http://www.nk7z.net
> > 
> > For MixW support see:
> > https://groups.yahoo.com/neo/groups/mixw/info
> > 
> > For SSTV help see:
> > http://groups.yahoo.com/neo/groups/MM-SSTV/info
> > 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to d...@nk7z.net
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] P3 Span settings

2016-02-17 Thread Clay Autery 
I haven't looked into the command language for the P3 in depth yet...

Is there a command for a "time delay".  It would appear that you need to
insert a time delay in between each individual command to allow the unit
time to respond to each step.

Just a SWAG...  (If the command doesn't exist, it looks like a prime
candidate for the next Firmware iteration)

__
Clay Autery, KG5LKV
(318) 518-1389

On 2/17/2016 2:46 PM, Dave Cole wrote:
> Hello Tim and Gary,
>
> I have done extensive testing in trying to get a macro to perform this
> exact behavior...  
>
> I do not believe "currently" there is a way to make this happen via
> macro commands.  
>
> If you perform the needed steps by hand, with lots of space between
> commands, it works, if you then place the exact same commands in a
> macro it fails.
>
> I tested by placing each command below in its own macro key using the
> P3 Macro tester software included with the P3 utility.  Here is an
> example:
>
> I have a DX station at 14.010, and I want to move 14.010 to the left
> edge of the P3, showing the upper 5 KHz ra
>
>
> Macro 1:
> #SPN000100;   
> Sets span to plus and minus 10 KHz.
>
> Macro 2:
> UP7;  
> Moves K3 up 5 KHz.
>
> Macro 3:  
> #FXT1;
> Places the P3 in sticky mode, (Fixed Tune), locking the transmit
> frequency to the center of the P3 screen.
>
> Macro 4:
> DN7;  
> Moves the K3 down 5, dragging the transmit freq down with it, and
> putting the transmit freq on the left edge of the P3, exposing the
> upper 10 KHz of the signals on the P3.
>
> If I then fire them one at a time, everything works as expected, the
> transmit frequency is on the lower left edge for an up split.
>
> If I place them in a single macro, it fails, every time...
>
>
> 73's, and thanks,
> Dave
>
> For software/hardware reviews see:
> http://www.nk7z.net
>
> For MixW support see:
> https://groups.yahoo.com/neo/groups/mixw/info
>
> For SSTV help see:
> http://groups.yahoo.com/neo/groups/MM-SSTV/info
>
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] P3 Span settings

2016-02-17 Thread Dave Cole 
Hello Tim and Gary,

I have done extensive testing in trying to get a macro to perform this
exact behavior...  

I do not believe "currently" there is a way to make this happen via
macro commands.  

If you perform the needed steps by hand, with lots of space between
commands, it works, if you then place the exact same commands in a
macro it fails.

I tested by placing each command below in its own macro key using the
P3 Macro tester software included with the P3 utility.  Here is an
example:

I have a DX station at 14.010, and I want to move 14.010 to the left
edge of the P3, showing the upper 5 KHz ra


Macro 1:
#SPN000100; 
Sets span to plus and minus 10 KHz.

Macro 2:
UP7;
Moves K3 up 5 KHz.

Macro 3:
#FXT1;  
Places the P3 in sticky mode, (Fixed Tune), locking the transmit
frequency to the center of the P3 screen.

Macro 4:
DN7;
Moves the K3 down 5, dragging the transmit freq down with it, and
putting the transmit freq on the left edge of the P3, exposing the
upper 10 KHz of the signals on the P3.

If I then fire them one at a time, everything works as expected, the
transmit frequency is on the lower left edge for an up split.

If I place them in a single macro, it fails, every time...


73's, and thanks,
Dave

For software/hardware reviews see:
http://www.nk7z.net

For MixW support see:
https://groups.yahoo.com/neo/groups/mixw/info

For SSTV help see:
http://groups.yahoo.com/neo/groups/MM-SSTV/info



On Wed, 2016-02-17 at 12:30 -0600, Grant Youngman wrote:
> You could --
> 
> Tune up 1/2 of your span width (in your example up 2.5 kHz). Press
> "CENTER" on the P3. That would put your desired DX signal at the left
> edge of the display and the mayhem out to the right. 
> 
> I'm unaware of any way to do this directly in the current firmware. 
> 
> Grant NQ5T
> 
> Sent from my iPhone
> 
> > On Feb 17, 2016, at 12:04 PM, a45wg  wrote:
> > 
> > Fellow Hams,
> >    Having spent the last 2 days playing with the P3 (very
> > impressed) - and eventually figuring out how to get the Function
> > keys to do something (Not well explained in the Manual IMHO), I’ve
> > got some Macro’s working - So next job - in the P3 Display is there
> > any way only to get the P3 Read The “Positive side” of the Span.
> > 
> > Say we have a DX transmitting on 28.030 Mhz …. If I set a Span of
> > 2.5 Khz - I see in the P3 28.0275 to 28.0325 - a SPAN of 5Khz, +/-
> > 2.5 Khz …. I get that. Very useful for looking for DX in a wideband
> > mode.
> > 
> > Is there anyway I can only limit the span to be 28.030 - 28.0325
> > i.e. just the positive side of the span.
> > 
> > Despite some rather strange DX expedition splits recently (not
> > mentioning a CW split of +7.5 Khz) I do not think  any DX
> > expeditions are using negative splits (Please, please do not start)
> > 
> > Any advice/guidance would be greatly appreciated. I am sure I can
> > do this in a Software I/Q SDR process - but I am really only trying
> > to do this from the P3.
> > 
> > Regards
> > 
> >   Tim
> >  A45WG
> > 
> > __
> > Elecraft mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/elecraft
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:Elecraft@mailman.qth.net
> > 
> > This list hosted by: http://www.qsl.net
> > Please help support this email list: http://www.qsl.net/donate.html
> > Message delivered to n...@tx.rr.com
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to d...@nk7z.net
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] P3 Span settings

2016-02-17 Thread Grant Youngman 
You could --

Tune up 1/2 of your span width (in your example up 2.5 kHz). Press "CENTER" on 
the P3. That would put your desired DX signal at the left edge of the display 
and the mayhem out to the right. 

I'm unaware of any way to do this directly in the current firmware. 

Grant NQ5T

Sent from my iPhone

> On Feb 17, 2016, at 12:04 PM, a45wg  wrote:
> 
> Fellow Hams,
>Having spent the last 2 days playing with the P3 (very impressed) - 
> and eventually figuring out how to get the Function keys to do something (Not 
> well explained in the Manual IMHO), I’ve got some Macro’s working - So next 
> job - in the P3 Display is there any way only to get the P3 Read The 
> “Positive side” of the Span.
> 
> Say we have a DX transmitting on 28.030 Mhz …. If I set a Span of 2.5 Khz - I 
> see in the P3 28.0275 to 28.0325 - a SPAN of 5Khz, +/- 2.5 Khz …. I get that. 
> Very useful for looking for DX in a wideband mode.
> 
> Is there anyway I can only limit the span to be 28.030 - 28.0325 i.e. just 
> the positive side of the span.
> 
> Despite some rather strange DX expedition splits recently (not mentioning a 
> CW split of +7.5 Khz) I do not think  any DX expeditions are using negative 
> splits (Please, please do not start)
> 
> Any advice/guidance would be greatly appreciated. I am sure I can do this in 
> a Software I/Q SDR process - but I am really only trying to do this from the 
> P3.
> 
> Regards
> 
>   Tim
>  A45WG
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@tx.rr.com
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] P3 Span settings

2016-02-17 Thread a45wg 
Fellow Hams,
Having spent the last 2 days playing with the P3 (very 
impressed) - and eventually figuring out how to get the Function keys to do 
something (Not well explained in the Manual IMHO), I’ve got some Macro’s 
working - So next job - in the P3 Display is there any way only to get the P3 
Read The “Positive side” of the Span.

Say we have a DX transmitting on 28.030 Mhz …. If I set a Span of 2.5 Khz - I 
see in the P3 28.0275 to 28.0325 - a SPAN of 5Khz, +/- 2.5 Khz …. I get that. 
Very useful for looking for DX in a wideband mode.

Is there anyway I can only limit the span to be 28.030 - 28.0325 i.e. just the 
positive side of the span.

Despite some rather strange DX expedition splits recently (not mentioning a CW 
split of +7.5 Khz) I do not think  any DX expeditions are using negative splits 
(Please, please do not start)

Any advice/guidance would be greatly appreciated. I am sure I can do this in a 
Software I/Q SDR process - but I am really only trying to do this from the P3.

Regards

   Tim
  A45WG

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com