RE: [Elecraft] KRX3 Installation Step
The current version of the KRX3 installation instructions errata has this item: Page 34, Figure 39: Delete the note and arrow on the left side starting with On some older K3 RF Boards Insert the following note: If jumper W4 is not in J64A as shown, it is hard wired on the RF board in front of J64A near to toroid L33. You may need to remove the KBPF3 board temporarily to cut and remove the jumper. Dick, K6KR -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Roy Morris Sent: Monday, September 08, 2008 5:01 AM To: elecraft@mailman.qth.net Subject: [Elecraft] KRX3 Installation Step On page 34 of the Installation and Opeation manual it says to remove the W4 jumber soldered between two pads located between J64A and the KIO3 board. My K3 RF board is Rev A. W4 is hard wired between two pads located between J64A and the KBPF3 board mounted above the K3 RF board. It looks as if I am going to have to temporarily remove the KBPF3 board to remove this jumper. Am I missing something here? Roy Morris W4WFB ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] KRX3 Installation Step
That's what I did. 73 Stewart G3RXQ On Mon, 8 Sep 2008 08:00:42 -0400, Roy Morris wrote: On page 34 of the Installation and Opeation manual it says to remove the W4 jumber soldered between two pads located between J64A and the KIO3 board. My K3 RF board is Rev A. W4 is hard wired between two pads located between J64A and the KBPF3 board mounted above the K3 RF board. It looks as if I am going to have to temporarily remove the KBPF3 board to remove this jumper. Am I missing something here? Roy Morris W4WFB ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] KRX3 Installation Step
yes yes yes. this note is CORRECT...for #44. in front of J64, and just under the back edge of the KBPF board bill At 07:47 AM 9/8/2008, Dick Dievendorff wrote: The current version of the KRX3 installation instructions errata has this item: Page 34, Figure 39: Delete the note and arrow on the left side starting with On some older K3 RF Boards Insert the following note: If jumper W4 is not in J64A as shown, it is hard wired on the RF board in front of J64A near to toroid L33. You may need to remove the KBPF3 board temporarily to cut and remove the jumper. Dick, K6KR -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Roy Morris Sent: Monday, September 08, 2008 5:01 AM To: elecraft@mailman.qth.net Subject: [Elecraft] KRX3 Installation Step On page 34 of the Installation and Opeation manual it says to remove the W4 jumber soldered between two pads located between J64A and the KIO3 board. My K3 RF board is Rev A. W4 is hard wired between two pads located between J64A and the KBPF3 board mounted above the K3 RF board. It looks as if I am going to have to temporarily remove the KBPF3 board to remove this jumper. Am I missing something here? Roy Morris W4WFB ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] KRX3 Installation Step
Roy Morris wrote: On page 34 of the Installation and Opeation manual it says to remove the W4 jumber soldered between two pads located between J64A and the KIO3 board. My K3 RF board is Rev A. W4 is hard wired between two pads located between J64A and the KBPF3 board mounted above the K3 RF board. It looks as if I am going to have to temporarily remove the KBPF3 board to remove this jumper. Am I missing something here? Roy Morris W4WFB No, you might have to take it out. I used a dental pick to break the jumper on my K3 (serial no. 7). -- 73, Vic, K2VCO Fresno CA http://www.qsl.net/k2vco ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com