Re: [Elecraft] K3 & SDR/IQ
I use SpectraVue as a panoramic adapter with my K3 and three XV transverters. Connected to the K3's IF out is an SDR-IQ, which is connected using the USB port to my PC. I don't have any issues with a 'variable frequency error' on 6 meters or any other band. I can point and click to a signal on the monitor and the K3 will follow, and vice-versa, regardless of the band or modes. 73 de Sebastian, W4AS On Jun 26, 2013, at 5:13 PM, "Joe Subich, W4TV" wrote: > > > Not if you connect via USB. > > I am (was) connecting via USB. > > 73, > > ... Joe, W4TV > > > On 6/26/2013 4:56 PM, Wes Stewart wrote: >> >>> From: "Joe Subich, W4TV" >> >>> >>> The only issue is the constantly changing IF offset in the >>> K3 (IS) >>> which SpectraVue does not track. This results in a variable >>> frequency >>> error based on mode. >> >> Not if you connect via USB. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 & SDR/IQ
> Not if you connect via USB. I am (was) connecting via USB. 73, ... Joe, W4TV On 6/26/2013 4:56 PM, Wes Stewart wrote: From: "Joe Subich, W4TV" The only issue is the constantly changing IF offset in the K3 (IS) which SpectraVue does not track. This results in a variable frequency error based on mode. Not if you connect via USB. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 & SDR/IQ
As a part of the referenced thread, that's not what it says at all. --- On Wed, 6/26/13, amsct...@comcast.net wrote: > From: amsct...@comcast.net > Subject: Re: [Elecraft] K3 & SDR/IQ > To: elecraft@mailman.qth.net > Date: Wednesday, June 26, 2013, 12:21 PM > SpectraView's HF tracking mode > doesn't allow for an IF tuning offset on frequencies higher > than the design limit of the SDR-IQ itself. I know the IF > frequency is well below that, but the software was never > supported "tracking panadapter" operation on 6M to the best > of my knowledge. You can still see the IF spectrum, but you > won't have a operator-transparent tracking ability. > > See the Yahoo SDR-IQ group thread on the topic here: > > http://groups.yahoo.com/group/SDR-IQ/message/6543 > > > Mike Alexander - N8MSA > > amsct...@comcast.net > > > - Original Message - > From: "Joe Subich, W4TV" > > To: elecraft@mailman.qth.net > > Sent: Wednesday, June 26, 2013 2:04:31 PM > Subject: Re: [Elecraft] K3 & SDR/IQ > > > On 6/26/2013 1:43 PM, Wes Stewart wrote: > > LP-Bridge will handle the serial port issue. > > Maybe - if none of your software uses one of the commands > that > LP-Bridge blocks or modifies. The N1MM Logger support team > will not > even accept bug reports if LP-Bridge is involved - any bug > must be > duplicated and documented with LP-Bridge removed due to the > known > issues. > > 73, > > ... Joe, W4TV > > > On 6/26/2013 1:43 PM, Wes Stewart wrote: > > LP-Bridge will handle the serial port issue. I run the > K3, Spectravue, DXBase and N1MM with one USB to Serial > adapter and ports to spare. > > > > > > --- On Tue, 6/25/13, Joe Subich, W4TV > wrote: > > > >> From: Joe Subich, W4TV > > >> Subject: Re: [Elecraft] K3 & SDR/IQ > >> To: elecraft@mailman.qth.net > > >> Date: Tuesday, June 25, 2013, 8:09 PM > >> > >> > So how do yu set it up to watch lower end of > 6m on the > >> K3, without > >> > using a transverter? > >> > >> Connect SDR-IQ to the IF Out jack (not the RX Ant) > and tune > >> SpectraVue > >> to 8.125 MHz manually *or* in SV's "ExtRadio Setup" > Select > >> the K3 and > >> uncheck "HF Tracking Mode." > >> > >> Note: If you want to use the frequency tracking > tied to the > >> IF, you > >> will need some kind of serial splitter to share the > K3 > >> serial port. > >> For more information see the SpectraVue Help file > section > >> 4.2, page > >> 59 and page 58 "IF Tracking". > >> > >> 73, > >> > >> ... Joe, W4TV > >> > >> > >> On 6/25/2013 9:55 PM, KD7YZ Bob wrote: > >>> Howdy K3' people: > >>> > >>> I have an SDR/IQ. I also have three Elecraft > >> transverters. When I > >>> connect a BNC to the BNC-RX "T" chain, and I > tune > >> Spectravue to 28.07 > >>> and the 6m xv50 transverter is "on", I am > looking at > >> the area around > >>> 50.070 .. I can look for beacons and Sporadic-E > > >> openings. > >>> > >>> Nothing new. > >>> > >>> However, the other day, I suspected the xv50 > >> transverter to on the > >>> Fritz. So I switched to the internal 6m Rx/Tx > section. > >> Made some > >>> contacts. > >>> > >>> So now I want to once again look for 6m Beacons > down > >> below 50.080 . > >>> My only option seems to be the IF BNC output. > >>> > >>> I connected there and tried to set Spectravue > for > >> 8.215; 10.0; 28.0 and > >>> still see nothing from 6m. I even tried to set > it at > >> 50.10, to no avail. > >>> > >>> So how do yu set it up to watch lower end of 6m > on the > >> K3, without > >>> using a transverter? > >>> > >>> thanks > >>> > >>> > >> > __ > > >> Elecraft mailing list > >> Home: http://mailman.qth.net/mailman/listinfo/elecraft > >> Help: http://mailman.qth.net/mmfaq.htm > >> Post: mailto:Elecraft@mailman.qth.net > > >> > >> This list hosted by: http:
Re: [Elecraft] K3 & SDR/IQ
> From: "Joe Subich, W4TV" > > The only issue is the constantly changing IF offset in the > K3 (IS) > which SpectraVue does not track. This results in a variable > frequency > error based on mode. Not if you connect via USB. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 & SDR/IQ
It didn't at the time that I sold mine - it would simply "top out" at 30 MHz. Thanks for the update. Mike Alexander - N8MSA amsct...@comcast.net - Original Message - From: "Joe Subich, W4TV" To: elecraft@mailman.qth.net Sent: Wednesday, June 26, 2013 3:46:19 PM Subject: Re: [Elecraft] K3 & SDR/IQ > SpectraView's HF tracking mode doesn't allow for an IF tuning offset > on frequencies higher than the design limit of the SDR-IQ itself. I > know the IF frequency is well below that, but the software was never > supported "tracking panadapter" operation on 6M to the best of my > knowledge. You can still see the IF spectrum, but you won't have a > operator-transparent tracking ability. Fortunately, that information is incorrect. I just retrieved my SDR-IQ from the shelf, connected it to the IF loop on my P3, loaded SpectraVue set the External Radio/Panadapter Setup as recommended in the SV help file and was running with a "tracking panadapter" on six meters. I used the 2nd CAT port capability in microHAM USB Device Router to provide the serial splitter function and the K3 tracks clicks in the SV spectrum/waterfall and SV tracks frequency changes from VFO A on the K3. Operation is the same on 6 meters as on 160 through 10. The only issue is the constantly changing IF offset in the K3 (IS) which SpectraVue does not track. This results in a variable frequency error based on mode. 73, ... Joe, W4TV On 6/26/2013 2:21 PM, amsct...@comcast.net wrote: > SpectraView's HF tracking mode doesn't allow for an IF tuning offset on > frequencies higher than the design limit of the SDR-IQ itself. I know the IF > frequency is well below that, but the software was never supported "tracking > panadapter" operation on 6M to the best of my knowledge. You can still see > the IF spectrum, but you won't have a operator-transparent tracking ability. > > See the Yahoo SDR-IQ group thread on the topic here: > > http://groups.yahoo.com/group/SDR-IQ/message/6543 > > > Mike Alexander - N8MSA > > amsct...@comcast.net > > - Original Message - > From: "Joe Subich, W4TV" > To: elecraft@mailman.qth.net > Sent: Wednesday, June 26, 2013 2:04:31 PM > Subject: Re: [Elecraft] K3 & SDR/IQ > > > On 6/26/2013 1:43 PM, Wes Stewart wrote: >> LP-Bridge will handle the serial port issue. > > Maybe - if none of your software uses one of the commands that > LP-Bridge blocks or modifies. The N1MM Logger support team will not > even accept bug reports if LP-Bridge is involved - any bug must be > duplicated and documented with LP-Bridge removed due to the known > issues. > > 73, > > ... Joe, W4TV > > > On 6/26/2013 1:43 PM, Wes Stewart wrote: >> LP-Bridge will handle the serial port issue. I run the K3, Spectravue, >> DXBase and N1MM with one USB to Serial adapter and ports to spare. >> >> >> --- On Tue, 6/25/13, Joe Subich, W4TV wrote: >> >>> From: Joe Subich, W4TV >>> Subject: Re: [Elecraft] K3 & SDR/IQ >>> To: elecraft@mailman.qth.net >>> Date: Tuesday, June 25, 2013, 8:09 PM >>> >>>> So how do yu set it up to watch lower end of 6m on the >>> K3, without >>>> using a transverter? >>> >>> Connect SDR-IQ to the IF Out jack (not the RX Ant) and tune >>> SpectraVue >>> to 8.125 MHz manually *or* in SV's "ExtRadio Setup" Select >>> the K3 and >>> uncheck "HF Tracking Mode." >>> >>> Note: If you want to use the frequency tracking tied to the >>> IF, you >>> will need some kind of serial splitter to share the K3 >>> serial port. >>> For more information see the SpectraVue Help file section >>> 4.2, page >>> 59 and page 58 "IF Tracking". >>> >>> 73, >>> >>> ... Joe, W4TV >>> >>> >>> On 6/25/2013 9:55 PM, KD7YZ Bob wrote: >>>> Howdy K3' people: >>>> >>>> I have an SDR/IQ. I also have three Elecraft >>> transverters. When I >>>> connect a BNC to the BNC-RX "T" chain, and I tune >>> Spectravue to 28.07 >>>> and the 6m xv50 transverter is "on", I am looking at >>> the area around >>>> 50.070 .. I can look for beacons and Sporadic-E >>> openings. >>>> >>>> Nothing new. >>>> >>>> However, the other day, I suspected the xv50 >>> transverter to on the >>>>
Re: [Elecraft] K3 & SDR/IQ
SpectraView's HF tracking mode doesn't allow for an IF tuning offset on frequencies higher than the design limit of the SDR-IQ itself. I know the IF frequency is well below that, but the software was never supported "tracking panadapter" operation on 6M to the best of my knowledge. You can still see the IF spectrum, but you won't have a operator-transparent tracking ability. Fortunately, that information is incorrect. I just retrieved my SDR-IQ from the shelf, connected it to the IF loop on my P3, loaded SpectraVue set the External Radio/Panadapter Setup as recommended in the SV help file and was running with a "tracking panadapter" on six meters. I used the 2nd CAT port capability in microHAM USB Device Router to provide the serial splitter function and the K3 tracks clicks in the SV spectrum/waterfall and SV tracks frequency changes from VFO A on the K3. Operation is the same on 6 meters as on 160 through 10. The only issue is the constantly changing IF offset in the K3 (IS) which SpectraVue does not track. This results in a variable frequency error based on mode. 73, ... Joe, W4TV On 6/26/2013 2:21 PM, amsct...@comcast.net wrote: SpectraView's HF tracking mode doesn't allow for an IF tuning offset on frequencies higher than the design limit of the SDR-IQ itself. I know the IF frequency is well below that, but the software was never supported "tracking panadapter" operation on 6M to the best of my knowledge. You can still see the IF spectrum, but you won't have a operator-transparent tracking ability. See the Yahoo SDR-IQ group thread on the topic here: http://groups.yahoo.com/group/SDR-IQ/message/6543 Mike Alexander - N8MSA amsct...@comcast.net - Original Message - From: "Joe Subich, W4TV" To: elecraft@mailman.qth.net Sent: Wednesday, June 26, 2013 2:04:31 PM Subject: Re: [Elecraft] K3 & SDR/IQ On 6/26/2013 1:43 PM, Wes Stewart wrote: LP-Bridge will handle the serial port issue. Maybe - if none of your software uses one of the commands that LP-Bridge blocks or modifies. The N1MM Logger support team will not even accept bug reports if LP-Bridge is involved - any bug must be duplicated and documented with LP-Bridge removed due to the known issues. 73, ... Joe, W4TV On 6/26/2013 1:43 PM, Wes Stewart wrote: LP-Bridge will handle the serial port issue. I run the K3, Spectravue, DXBase and N1MM with one USB to Serial adapter and ports to spare. --- On Tue, 6/25/13, Joe Subich, W4TV wrote: From: Joe Subich, W4TV Subject: Re: [Elecraft] K3 & SDR/IQ To: elecraft@mailman.qth.net Date: Tuesday, June 25, 2013, 8:09 PM So how do yu set it up to watch lower end of 6m on the K3, without using a transverter? Connect SDR-IQ to the IF Out jack (not the RX Ant) and tune SpectraVue to 8.125 MHz manually *or* in SV's "ExtRadio Setup" Select the K3 and uncheck "HF Tracking Mode." Note: If you want to use the frequency tracking tied to the IF, you will need some kind of serial splitter to share the K3 serial port. For more information see the SpectraVue Help file section 4.2, page 59 and page 58 "IF Tracking". 73, ... Joe, W4TV On 6/25/2013 9:55 PM, KD7YZ Bob wrote: Howdy K3' people: I have an SDR/IQ. I also have three Elecraft transverters. When I connect a BNC to the BNC-RX "T" chain, and I tune Spectravue to 28.07 and the 6m xv50 transverter is "on", I am looking at the area around 50.070 .. I can look for beacons and Sporadic-E openings. Nothing new. However, the other day, I suspected the xv50 transverter to on the Fritz. So I switched to the internal 6m Rx/Tx section. Made some contacts. So now I want to once again look for 6m Beacons down below 50.080 . My only option seems to be the IF BNC output. I connected there and tried to set Spectravue for 8.215; 10.0; 28.0 and still see nothing from 6m. I even tried to set it at 50.10, to no avail. So how do yu set it up to watch lower end of 6m on the K3, without using a transverter? thanks __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: ma
Re: [Elecraft] K3 & SDR/IQ
SpectraView's HF tracking mode doesn't allow for an IF tuning offset on frequencies higher than the design limit of the SDR-IQ itself. I know the IF frequency is well below that, but the software was never supported "tracking panadapter" operation on 6M to the best of my knowledge. You can still see the IF spectrum, but you won't have a operator-transparent tracking ability. See the Yahoo SDR-IQ group thread on the topic here: http://groups.yahoo.com/group/SDR-IQ/message/6543 Mike Alexander - N8MSA amsct...@comcast.net - Original Message - From: "Joe Subich, W4TV" To: elecraft@mailman.qth.net Sent: Wednesday, June 26, 2013 2:04:31 PM Subject: Re: [Elecraft] K3 & SDR/IQ On 6/26/2013 1:43 PM, Wes Stewart wrote: > LP-Bridge will handle the serial port issue. Maybe - if none of your software uses one of the commands that LP-Bridge blocks or modifies. The N1MM Logger support team will not even accept bug reports if LP-Bridge is involved - any bug must be duplicated and documented with LP-Bridge removed due to the known issues. 73, ... Joe, W4TV On 6/26/2013 1:43 PM, Wes Stewart wrote: > LP-Bridge will handle the serial port issue. I run the K3, Spectravue, DXBase > and N1MM with one USB to Serial adapter and ports to spare. > > > --- On Tue, 6/25/13, Joe Subich, W4TV wrote: > >> From: Joe Subich, W4TV >> Subject: Re: [Elecraft] K3 & SDR/IQ >> To: elecraft@mailman.qth.net >> Date: Tuesday, June 25, 2013, 8:09 PM >> >> > So how do yu set it up to watch lower end of 6m on the >> K3, without >> > using a transverter? >> >> Connect SDR-IQ to the IF Out jack (not the RX Ant) and tune >> SpectraVue >> to 8.125 MHz manually *or* in SV's "ExtRadio Setup" Select >> the K3 and >> uncheck "HF Tracking Mode." >> >> Note: If you want to use the frequency tracking tied to the >> IF, you >> will need some kind of serial splitter to share the K3 >> serial port. >> For more information see the SpectraVue Help file section >> 4.2, page >> 59 and page 58 "IF Tracking". >> >> 73, >> >> ... Joe, W4TV >> >> >> On 6/25/2013 9:55 PM, KD7YZ Bob wrote: >>> Howdy K3' people: >>> >>> I have an SDR/IQ. I also have three Elecraft >> transverters. When I >>> connect a BNC to the BNC-RX "T" chain, and I tune >> Spectravue to 28.07 >>> and the 6m xv50 transverter is "on", I am looking at >> the area around >>> 50.070 .. I can look for beacons and Sporadic-E >> openings. >>> >>> Nothing new. >>> >>> However, the other day, I suspected the xv50 >> transverter to on the >>> Fritz. So I switched to the internal 6m Rx/Tx section. >> Made some >>> contacts. >>> >>> So now I want to once again look for 6m Beacons down >> below 50.080 . >>> My only option seems to be the IF BNC output. >>> >>> I connected there and tried to set Spectravue for >> 8.215; 10.0; 28.0 and >>> still see nothing from 6m. I even tried to set it at >> 50.10, to no avail. >>> >>> So how do yu set it up to watch lower end of 6m on the >> K3, without >>> using a transverter? >>> >>> thanks >>> >>> >> __ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 & SDR/IQ
On 6/26/2013 1:43 PM, Wes Stewart wrote: > LP-Bridge will handle the serial port issue. Maybe - if none of your software uses one of the commands that LP-Bridge blocks or modifies. The N1MM Logger support team will not even accept bug reports if LP-Bridge is involved - any bug must be duplicated and documented with LP-Bridge removed due to the known issues. 73, ... Joe, W4TV On 6/26/2013 1:43 PM, Wes Stewart wrote: LP-Bridge will handle the serial port issue. I run the K3, Spectravue, DXBase and N1MM with one USB to Serial adapter and ports to spare. --- On Tue, 6/25/13, Joe Subich, W4TV wrote: From: Joe Subich, W4TV Subject: Re: [Elecraft] K3 & SDR/IQ To: elecraft@mailman.qth.net Date: Tuesday, June 25, 2013, 8:09 PM > So how do yu set it up to watch lower end of 6m on the K3, without > using a transverter? Connect SDR-IQ to the IF Out jack (not the RX Ant) and tune SpectraVue to 8.125 MHz manually *or* in SV's "ExtRadio Setup" Select the K3 and uncheck "HF Tracking Mode." Note: If you want to use the frequency tracking tied to the IF, you will need some kind of serial splitter to share the K3 serial port. For more information see the SpectraVue Help file section 4.2, page 59 and page 58 "IF Tracking". 73, ... Joe, W4TV On 6/25/2013 9:55 PM, KD7YZ Bob wrote: Howdy K3' people: I have an SDR/IQ. I also have three Elecraft transverters. When I connect a BNC to the BNC-RX "T" chain, and I tune Spectravue to 28.07 and the 6m xv50 transverter is "on", I am looking at the area around 50.070 .. I can look for beacons and Sporadic-E openings. Nothing new. However, the other day, I suspected the xv50 transverter to on the Fritz. So I switched to the internal 6m Rx/Tx section. Made some contacts. So now I want to once again look for 6m Beacons down below 50.080 . My only option seems to be the IF BNC output. I connected there and tried to set Spectravue for 8.215; 10.0; 28.0 and still see nothing from 6m. I even tried to set it at 50.10, to no avail. So how do yu set it up to watch lower end of 6m on the K3, without using a transverter? thanks __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 & SDR/IQ
LP-Bridge will handle the serial port issue. I run the K3, Spectravue, DXBase and N1MM with one USB to Serial adapter and ports to spare. --- On Tue, 6/25/13, Joe Subich, W4TV wrote: > From: Joe Subich, W4TV > Subject: Re: [Elecraft] K3 & SDR/IQ > To: elecraft@mailman.qth.net > Date: Tuesday, June 25, 2013, 8:09 PM > > > So how do yu set it up to watch lower end of 6m on the > K3, without > > using a transverter? > > Connect SDR-IQ to the IF Out jack (not the RX Ant) and tune > SpectraVue > to 8.125 MHz manually *or* in SV's "ExtRadio Setup" Select > the K3 and > uncheck "HF Tracking Mode." > > Note: If you want to use the frequency tracking tied to the > IF, you > will need some kind of serial splitter to share the K3 > serial port. > For more information see the SpectraVue Help file section > 4.2, page > 59 and page 58 "IF Tracking". > > 73, > > ... Joe, W4TV > > > On 6/25/2013 9:55 PM, KD7YZ Bob wrote: > > Howdy K3' people: > > > > I have an SDR/IQ. I also have three Elecraft > transverters. When I > > connect a BNC to the BNC-RX "T" chain, and I tune > Spectravue to 28.07 > > and the 6m xv50 transverter is "on", I am looking at > the area around > > 50.070 .. I can look for beacons and Sporadic-E > openings. > > > > Nothing new. > > > > However, the other day, I suspected the xv50 > transverter to on the > > Fritz. So I switched to the internal 6m Rx/Tx section. > Made some > > contacts. > > > > So now I want to once again look for 6m Beacons down > below 50.080 . > > My only option seems to be the IF BNC output. > > > > I connected there and tried to set Spectravue for > 8.215; 10.0; 28.0 and > > still see nothing from 6m. I even tried to set it at > 50.10, to no avail. > > > > So how do yu set it up to watch lower end of 6m on the > K3, without > > using a transverter? > > > > thanks > > > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 & SDR/IQ
You don't say what software you are running but if it's Spectravue, just go to the ExtRadio tab, select the K3 from the drop down list, set the com port, baud rate and check mode tracking. In the SDR-IQ setup, set the filter BW to 100 or 150. Press F12 and you should be in business. Wes, N7WS --- On Tue, 6/25/13, KD7YZ Bob wrote: > From: KD7YZ Bob > Subject: [Elecraft] K3 & SDR/IQ > To: "'K3 List'" > Date: Tuesday, June 25, 2013, 7:55 PM > Howdy K3' people: > > I have an SDR/IQ. I also have three Elecraft transverters. > When I > connect a BNC to the BNC-RX "T" chain, and I tune Spectravue > to 28.07 > and the 6m xv50 transverter is "on", I am looking at the > area around > 50.070 .. I can look for beacons and Sporadic-E openings. > > Nothing new. > > However, the other day, I suspected the xv50 > transverter to on the > Fritz. So I switched to the internal 6m Rx/Tx section. Made > some > contacts. > > So now I want to once again look for 6m Beacons down below > 50.080 . > My only option seems to be the IF BNC output. > > I connected there and tried to set Spectravue for 8.215; > 10.0; 28.0 and > still see nothing from 6m. I even tried to set it at 50.10, > to no avail. > > So how do yu set it up to watch lower end of 6m on the K3, > without > using a transverter? > > thanks > > > -- > 73 > KD7YZ Bob > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 & SDR/IQ
> So how do yu set it up to watch lower end of 6m on the K3, without > using a transverter? Connect SDR-IQ to the IF Out jack (not the RX Ant) and tune SpectraVue to 8.125 MHz manually *or* in SV's "ExtRadio Setup" Select the K3 and uncheck "HF Tracking Mode." Note: If you want to use the frequency tracking tied to the IF, you will need some kind of serial splitter to share the K3 serial port. For more information see the SpectraVue Help file section 4.2, page 59 and page 58 "IF Tracking". 73, ... Joe, W4TV On 6/25/2013 9:55 PM, KD7YZ Bob wrote: Howdy K3' people: I have an SDR/IQ. I also have three Elecraft transverters. When I connect a BNC to the BNC-RX "T" chain, and I tune Spectravue to 28.07 and the 6m xv50 transverter is "on", I am looking at the area around 50.070 .. I can look for beacons and Sporadic-E openings. Nothing new. However, the other day, I suspected the xv50 transverter to on the Fritz. So I switched to the internal 6m Rx/Tx section. Made some contacts. So now I want to once again look for 6m Beacons down below 50.080 . My only option seems to be the IF BNC output. I connected there and tried to set Spectravue for 8.215; 10.0; 28.0 and still see nothing from 6m. I even tried to set it at 50.10, to no avail. So how do yu set it up to watch lower end of 6m on the K3, without using a transverter? thanks __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 + SDR-IQ and regular CW operation
On Thursday Wilhelm used a Straight-Key to send: -Original Comment--- > Bob, > You are OK. > There is some bleed-through "Whew!" .:B Thanks Don. And thanks too to Irizzary who replied. -- Best regards, Bob KD7YZWin7-64bit + K3 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 + SDR-IQ and regular CW operation
I use a mfj t/r switch on te front end of the sdr and see the same thing. Been using for over a year and the sdr seems fine. My sdr is feed by a seperate antenna through the tr sswitch. - Original Message - From: Don Wilhelm [mailto:w3...@embarqmail.com] Sent: Thursday, December 13, 2012 09:58 AM To: KD7YZ Bob Cc: K3 List Subject: Re: [Elecraft] K3 + SDR-IQ and regular CW operation Bob, You are OK. There is some bleed-through of the IF output during transmit, and I believe that is what you are seeing. 73. Don W3FPR On 12/13/2012 8:16 AM, KD7YZ Bob wrote: > Howdy K3' people: > > I was wondering what precautions are taken, or I need to invoke, when I > use any form of transmitting? > > At present, the SDR-IQ is connected to the K3's IF BNC. K3's output is > through KAT500 then outside to the antenna some distance away at 80 to > 85 feet AGL. Power, while I am testing, is circa 5 to 10 watts. > > So I keyed the K3 a few times; called CQ, and so forth. I see my own > trace on the WF of CW-Skimmer, which is set to operate with SDR-IQ as > its "Input" . > > Am I golden? Or am I about to overload the K3 and kill it? > > thanks > > > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 + SDR-IQ and regular CW operation
Bob, You are OK. There is some bleed-through of the IF output during transmit, and I believe that is what you are seeing. 73. Don W3FPR On 12/13/2012 8:16 AM, KD7YZ Bob wrote: Howdy K3' people: I was wondering what precautions are taken, or I need to invoke, when I use any form of transmitting? At present, the SDR-IQ is connected to the K3's IF BNC. K3's output is through KAT500 then outside to the antenna some distance away at 80 to 85 feet AGL. Power, while I am testing, is circa 5 to 10 watts. So I keyed the K3 a few times; called CQ, and so forth. I see my own trace on the WF of CW-Skimmer, which is set to operate with SDR-IQ as its "Input" . Am I golden? Or am I about to overload the K3 and kill it? thanks __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 & SDR-IQ from re-space
Bob, What are your specific questions? I have the K3 with SDR-IQ here. I've used it both with the IF connection (as a panadapter) and with an RF connection (RX Out/RX In and a splitter) for CW Skimmer. It was in use for about a year but is off-line at the present - I'm not completely sure the receiver hasn't been damaged and don't have the time to trouble shoot it right now (either RX problem or computer issue). 73, ... Joe, W4TV On 12/2/2012 9:52 PM, KD7YZ Bob wrote: Howdy K3' people: I did some more research on my goals of using my new K3, & Sub-RX with matching 8-pole, for low-low bands. If anyone uses the actual SDR-IQ with a K3, I would like some guidance. And I' would like to ask is it possible to listen/hear a particular point on the displayed segment when used in conjunction with the K3? On-List or direct email, either way, I'd like to get one this week, so answers would really help out. :-B __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 + SDR-IQ + CW Skimmer+ SpectraVue
Why not publicly? Would be helpful to others, I should think, if it is possible. -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Paul Christensen Sent: Sunday, August 08, 2010 8:16 AM To: elecraft@mailman.qth.net Subject: [Elecraft] K3 + SDR-IQ + CW Skimmer+ SpectraVue Anyone know if it's possible to configure all four of the above to simultaneously run CW Skimmer and SpectraVue? I have tired every possible iteration to port audio from SpectraVue to CW Skimmer with no luck. I've also tried VAC and still no luck. If there's anyone that's successfully tried this, please contact me off-line by private E-mail. Tnx! Paul, W9AC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html This email message, including any attachments, is for the sole use of the intended recipient(s) and may contain information that is proprietary, confidential, and exempt from disclosure under applicable law. Any unauthorized review, use, disclosure, or distribution is prohibited. If you have received this email in error please notify the sender by return email and delete the original message. Please note, the recipient should check this email and any attachments for the presence of viruses. The organization accepts no liability for any damage caused by any virus transmitted by this email. = __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html