Re: [Elecraft] K3 settings question
Hi Ian, That was it. That fixed the low volume issue. It was set to 5, which is very low. Many thanks, Chris KM1B On Tue, Oct 8, 2024 at 5:46 PM Ian Kahn wrote: > Chris, > > Do you have Tech Mode turned on in your K3's menu? This enables menu > options that are otherwise hidden. > > 73 de, > > Ian, NV4C > > > <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail> > Virus-free.www.avast.com > <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail> > <#m_6087988043103223477_DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2> > > On Tue, Oct 8, 2024 at 5:36 PM Chris wrote: > >> They both have AF GAIN at HI. I am going to update the firmware and will >> see if it is related to AGC settings. I am still learning as these two >> K3's >> are fairly new to me. >> >> Thanks for your info. >> >> Chris KM1B >> >> >> On Tue, Oct 8, 2024 at 5:20 PM Chris wrote: >> >> > K3 with 8xxx has firmware version of 5.29, and I don't see AGC settings >> > other than AGC DCY and AGC HLD. I assume I need to update the firmware >> to >> > the latest one. >> > >> > Chris KM1B >> > >> > On Tue, Oct 8, 2024 at 4:01 PM David Sumner > > >> > wrote: >> > >> >> Chris, check the settings under CONFIG: AF GAIN. It is switchable >> between >> >> low and high. >> >> >> >> 73, >> >> Dave K1ZZ >> >> . >> >> >> >> On Tue, Oct 8, 2024 at 1:36 PM parinc1 wrote: >> >> >> >>> As I recall, Ten Tec was known for setting their AGC threshold quite >> >>> low. The result was that owners always commented on how "quiet" their >> >>> receivers were. >> >>> Turn off the AGC and then compare your volume settings. >> >>> All a matter of taste. >> >>> Dale W4OP >> >>> >> >>> From: elecraft-boun...@mailman.qth.net < >> elecraft-boun...@mailman.qth.net> >> >>> on behalf of Chris >> >>> Sent: Tuesday, October 8, 2024 10:45 AM >> >>> To: David Hachadorian >> >>> Cc: Reflector Elecraft >> >>> Subject: Re: [Elecraft] K3 settings question >> >>> >> >>> It is interesting to see the AGC THR makes a noticeable difference, >> and I >> >>> will do the same as you suggested. >> >>> >> >>> Another note is that the audio volume is much different between them. >> The >> >>> one with 09xx serial number is noticeably louder. When 09xx is set at >> >>> the 9 >> >>> o'clock position, 8xxx needs to be at 12 o'clock to have a comparable >> >>> audio >> >>> volume. Any help would be greatly appreciated. >> >>> >> >>> Thanks, >> >>> >> >>> Chris >> >>> >> >>> >> >>> On Mon, Oct 7, 2024 at 10:19 AM David Hachadorian < >> k6ll.d...@gmail.com> >> >>> wrote: >> >>> >> >>> > It's probably the AGC settings. Here are my favorites: >> >>> > agc dcy soft >> >>> > hld 0.2 >> >>> > pls nor >> >>> > slp 000 >> >>> > thr cw20, rtty17, ssb15 >> >>> > f 200 >> >>> > s 020 >> >>> > >> >>> > I have pf2 programmed to bring up agc thr, so I can change it when >> >>> > switching modes. >> >>> > >> >>> > Dave Hachadorian, K6LL >> >>> > Yuma, AZ >> >>> > >> >>> > >> >>> > On 10/7/2024 6:24 AM, Chris wrote: >> >>> > >> >>> > Hello, >> >>> > >> >>> > I am a happy owner of K3. I came across another K3 with an early >> >>> serial >> >>> > number below 1000 in good condition at a local hamfest. It works >> well, >> >>> > somehow better than my current K3, so my first reaction was, Wow. >> It >> >>> seems >> >>> > to have a lower noise floor and sounds slightly better. >> >>> > >> >>> > My question is, how can it be? I have yet to compare all the >> settings >
Re: [Elecraft] K3 settings question
Chris, Do you have Tech Mode turned on in your K3's menu? This enables menu options that are otherwise hidden. 73 de, Ian, NV4C <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail> Virus-free.www.avast.com <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail> <#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2> On Tue, Oct 8, 2024 at 5:36 PM Chris wrote: > They both have AF GAIN at HI. I am going to update the firmware and will > see if it is related to AGC settings. I am still learning as these two K3's > are fairly new to me. > > Thanks for your info. > > Chris KM1B > > > On Tue, Oct 8, 2024 at 5:20 PM Chris wrote: > > > K3 with 8xxx has firmware version of 5.29, and I don't see AGC settings > > other than AGC DCY and AGC HLD. I assume I need to update the firmware to > > the latest one. > > > > Chris KM1B > > > > On Tue, Oct 8, 2024 at 4:01 PM David Sumner > > wrote: > > > >> Chris, check the settings under CONFIG: AF GAIN. It is switchable > between > >> low and high. > >> > >> 73, > >> Dave K1ZZ > >> . > >> > >> On Tue, Oct 8, 2024 at 1:36 PM parinc1 wrote: > >> > >>> As I recall, Ten Tec was known for setting their AGC threshold quite > >>> low. The result was that owners always commented on how "quiet" their > >>> receivers were. > >>> Turn off the AGC and then compare your volume settings. > >>> All a matter of taste. > >>> Dale W4OP > >>> > >>> From: elecraft-boun...@mailman.qth.net < > elecraft-boun...@mailman.qth.net> > >>> on behalf of Chris > >>> Sent: Tuesday, October 8, 2024 10:45 AM > >>> To: David Hachadorian > >>> Cc: Reflector Elecraft > >>> Subject: Re: [Elecraft] K3 settings question > >>> > >>> It is interesting to see the AGC THR makes a noticeable difference, > and I > >>> will do the same as you suggested. > >>> > >>> Another note is that the audio volume is much different between them. > The > >>> one with 09xx serial number is noticeably louder. When 09xx is set at > >>> the 9 > >>> o'clock position, 8xxx needs to be at 12 o'clock to have a comparable > >>> audio > >>> volume. Any help would be greatly appreciated. > >>> > >>> Thanks, > >>> > >>> Chris > >>> > >>> > >>> On Mon, Oct 7, 2024 at 10:19 AM David Hachadorian > > >>> wrote: > >>> > >>> > It's probably the AGC settings. Here are my favorites: > >>> > agc dcy soft > >>> > hld 0.2 > >>> > pls nor > >>> > slp 000 > >>> > thr cw20, rtty17, ssb15 > >>> > f 200 > >>> > s 020 > >>> > > >>> > I have pf2 programmed to bring up agc thr, so I can change it when > >>> > switching modes. > >>> > > >>> > Dave Hachadorian, K6LL > >>> > Yuma, AZ > >>> > > >>> > > >>> > On 10/7/2024 6:24 AM, Chris wrote: > >>> > > >>> > Hello, > >>> > > >>> > I am a happy owner of K3. I came across another K3 with an early > >>> serial > >>> > number below 1000 in good condition at a local hamfest. It works > well, > >>> > somehow better than my current K3, so my first reaction was, Wow. It > >>> seems > >>> > to have a lower noise floor and sounds slightly better. > >>> > > >>> > My question is, how can it be? I have yet to compare all the > settings > >>> for > >>> > either radio. The filter in my current K3 is 2.7kHz, and the new > (new > >>> to > >>> > me) K3 has 2.8kHz. I am not 100% sure these filters can make that > much > >>> > difference. Besides that, all hardware configurations are pretty > much > >>> the > >>> > same. They both have updated KSYN3A modules. This K3 with a lower > >>> serial > >>> > number has KAT3, and my current K3 doesn't because I have KAT500. > >>> > > >>> > Any suggestions? > >>> > > >>> > Many thanks, > >>> > > >>> &g
Re: [Elecraft] K3 settings question
They both have AF GAIN at HI. I am going to update the firmware and will see if it is related to AGC settings. I am still learning as these two K3's are fairly new to me. Thanks for your info. Chris KM1B On Tue, Oct 8, 2024 at 5:20 PM Chris wrote: > K3 with 8xxx has firmware version of 5.29, and I don't see AGC settings > other than AGC DCY and AGC HLD. I assume I need to update the firmware to > the latest one. > > Chris KM1B > > On Tue, Oct 8, 2024 at 4:01 PM David Sumner > wrote: > >> Chris, check the settings under CONFIG: AF GAIN. It is switchable between >> low and high. >> >> 73, >> Dave K1ZZ >> . >> >> On Tue, Oct 8, 2024 at 1:36 PM parinc1 wrote: >> >>> As I recall, Ten Tec was known for setting their AGC threshold quite >>> low. The result was that owners always commented on how "quiet" their >>> receivers were. >>> Turn off the AGC and then compare your volume settings. >>> All a matter of taste. >>> Dale W4OP >>> >>> From: elecraft-boun...@mailman.qth.net >>> on behalf of Chris >>> Sent: Tuesday, October 8, 2024 10:45 AM >>> To: David Hachadorian >>> Cc: Reflector Elecraft >>> Subject: Re: [Elecraft] K3 settings question >>> >>> It is interesting to see the AGC THR makes a noticeable difference, and I >>> will do the same as you suggested. >>> >>> Another note is that the audio volume is much different between them. The >>> one with 09xx serial number is noticeably louder. When 09xx is set at >>> the 9 >>> o'clock position, 8xxx needs to be at 12 o'clock to have a comparable >>> audio >>> volume. Any help would be greatly appreciated. >>> >>> Thanks, >>> >>> Chris >>> >>> >>> On Mon, Oct 7, 2024 at 10:19 AM David Hachadorian >>> wrote: >>> >>> > It's probably the AGC settings. Here are my favorites: >>> > agc dcy soft >>> > hld 0.2 >>> > pls nor >>> > slp 000 >>> > thr cw20, rtty17, ssb15 >>> > f 200 >>> > s 020 >>> > >>> > I have pf2 programmed to bring up agc thr, so I can change it when >>> > switching modes. >>> > >>> > Dave Hachadorian, K6LL >>> > Yuma, AZ >>> > >>> > >>> > On 10/7/2024 6:24 AM, Chris wrote: >>> > >>> > Hello, >>> > >>> > I am a happy owner of K3. I came across another K3 with an early >>> serial >>> > number below 1000 in good condition at a local hamfest. It works well, >>> > somehow better than my current K3, so my first reaction was, Wow. It >>> seems >>> > to have a lower noise floor and sounds slightly better. >>> > >>> > My question is, how can it be? I have yet to compare all the settings >>> for >>> > either radio. The filter in my current K3 is 2.7kHz, and the new (new >>> to >>> > me) K3 has 2.8kHz. I am not 100% sure these filters can make that much >>> > difference. Besides that, all hardware configurations are pretty much >>> the >>> > same. They both have updated KSYN3A modules. This K3 with a lower >>> serial >>> > number has KAT3, and my current K3 doesn't because I have KAT500. >>> > >>> > Any suggestions? >>> > >>> > Many thanks, >>> > >>> > Chris KM1B >>> > __ >>> > Elecraft mailing list >>> > Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> > Help: http://mailman.qth.net/mmfaq.htm >>> > Post: mailto:Elecraft@mailman.qth.net >>> > >>> > This list hosted by: http://www.qsl.net >>> > Please help support this email list: http://www.qsl.net/donate.html >>> > Message delivered to k6ll.d...@gmail.com >>> > >>> > >>> > >>> __ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:Elecraft@mailman.qth.net >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >>> Message delivered to pari...@frontier.com >>> __ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:Elecraft@mailman.qth.net >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >>> >> Message delivered to dave.sumner.k...@gmail.com >> >> __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 settings question
K3 with 8xxx has firmware version of 5.29, and I don't see AGC settings other than AGC DCY and AGC HLD. I assume I need to update the firmware to the latest one. Chris KM1B On Tue, Oct 8, 2024 at 4:01 PM David Sumner wrote: > Chris, check the settings under CONFIG: AF GAIN. It is switchable between > low and high. > > 73, > Dave K1ZZ > . > > On Tue, Oct 8, 2024 at 1:36 PM parinc1 wrote: > >> As I recall, Ten Tec was known for setting their AGC threshold quite >> low. The result was that owners always commented on how "quiet" their >> receivers were. >> Turn off the AGC and then compare your volume settings. >> All a matter of taste. >> Dale W4OP >> >> From: elecraft-boun...@mailman.qth.net >> on behalf of Chris >> Sent: Tuesday, October 8, 2024 10:45 AM >> To: David Hachadorian >> Cc: Reflector Elecraft >> Subject: Re: [Elecraft] K3 settings question >> >> It is interesting to see the AGC THR makes a noticeable difference, and I >> will do the same as you suggested. >> >> Another note is that the audio volume is much different between them. The >> one with 09xx serial number is noticeably louder. When 09xx is set at the >> 9 >> o'clock position, 8xxx needs to be at 12 o'clock to have a comparable >> audio >> volume. Any help would be greatly appreciated. >> >> Thanks, >> >> Chris >> >> >> On Mon, Oct 7, 2024 at 10:19 AM David Hachadorian >> wrote: >> >> > It's probably the AGC settings. Here are my favorites: >> > agc dcy soft >> > hld 0.2 >> > pls nor >> > slp 000 >> > thr cw20, rtty17, ssb15 >> > f 200 >> > s 020 >> > >> > I have pf2 programmed to bring up agc thr, so I can change it when >> > switching modes. >> > >> > Dave Hachadorian, K6LL >> > Yuma, AZ >> > >> > >> > On 10/7/2024 6:24 AM, Chris wrote: >> > >> > Hello, >> > >> > I am a happy owner of K3. I came across another K3 with an early serial >> > number below 1000 in good condition at a local hamfest. It works well, >> > somehow better than my current K3, so my first reaction was, Wow. It >> seems >> > to have a lower noise floor and sounds slightly better. >> > >> > My question is, how can it be? I have yet to compare all the settings >> for >> > either radio. The filter in my current K3 is 2.7kHz, and the new (new >> to >> > me) K3 has 2.8kHz. I am not 100% sure these filters can make that much >> > difference. Besides that, all hardware configurations are pretty much >> the >> > same. They both have updated KSYN3A modules. This K3 with a lower >> serial >> > number has KAT3, and my current K3 doesn't because I have KAT500. >> > >> > Any suggestions? >> > >> > Many thanks, >> > >> > Chris KM1B >> > __ >> > Elecraft mailing list >> > Home: http://mailman.qth.net/mailman/listinfo/elecraft >> > Help: http://mailman.qth.net/mmfaq.htm >> > Post: mailto:Elecraft@mailman.qth.net >> > >> > This list hosted by: http://www.qsl.net >> > Please help support this email list: http://www.qsl.net/donate.html >> > Message delivered to k6ll.d...@gmail.com >> > >> > >> > >> __ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to pari...@frontier.com >> __ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> > Message delivered to dave.sumner.k...@gmail.com > > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 settings question
Chris, check the settings under CONFIG: AF GAIN. It is switchable between low and high. 73, Dave K1ZZ . On Tue, Oct 8, 2024 at 1:36 PM parinc1 wrote: > As I recall, Ten Tec was known for setting their AGC threshold quite low. > The result was that owners always commented on how "quiet" their receivers > were. > Turn off the AGC and then compare your volume settings. > All a matter of taste. > Dale W4OP > > From: elecraft-boun...@mailman.qth.net > on behalf of Chris > Sent: Tuesday, October 8, 2024 10:45 AM > To: David Hachadorian > Cc: Reflector Elecraft > Subject: Re: [Elecraft] K3 settings question > > It is interesting to see the AGC THR makes a noticeable difference, and I > will do the same as you suggested. > > Another note is that the audio volume is much different between them. The > one with 09xx serial number is noticeably louder. When 09xx is set at the 9 > o'clock position, 8xxx needs to be at 12 o'clock to have a comparable audio > volume. Any help would be greatly appreciated. > > Thanks, > > Chris > > > On Mon, Oct 7, 2024 at 10:19 AM David Hachadorian > wrote: > > > It's probably the AGC settings. Here are my favorites: > > agc dcy soft > > hld 0.2 > > pls nor > > slp 000 > > thr cw20, rtty17, ssb15 > > f 200 > > s 020 > > > > I have pf2 programmed to bring up agc thr, so I can change it when > > switching modes. > > > > Dave Hachadorian, K6LL > > Yuma, AZ > > > > > > On 10/7/2024 6:24 AM, Chris wrote: > > > > Hello, > > > > I am a happy owner of K3. I came across another K3 with an early serial > > number below 1000 in good condition at a local hamfest. It works well, > > somehow better than my current K3, so my first reaction was, Wow. It > seems > > to have a lower noise floor and sounds slightly better. > > > > My question is, how can it be? I have yet to compare all the settings > for > > either radio. The filter in my current K3 is 2.7kHz, and the new (new to > > me) K3 has 2.8kHz. I am not 100% sure these filters can make that much > > difference. Besides that, all hardware configurations are pretty much > the > > same. They both have updated KSYN3A modules. This K3 with a lower > serial > > number has KAT3, and my current K3 doesn't because I have KAT500. > > > > Any suggestions? > > > > Many thanks, > > > > Chris KM1B > > __ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:Elecraft@mailman.qth.net > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > Message delivered to k6ll.d...@gmail.com > > > > > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to pari...@frontier.com > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to dave.sumner.k...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 settings question
As I recall, Ten Tec was known for setting their AGC threshold quite low. The result was that owners always commented on how "quiet" their receivers were. Turn off the AGC and then compare your volume settings. All a matter of taste. Dale W4OP From: elecraft-boun...@mailman.qth.net on behalf of Chris Sent: Tuesday, October 8, 2024 10:45 AM To: David Hachadorian Cc: Reflector Elecraft Subject: Re: [Elecraft] K3 settings question It is interesting to see the AGC THR makes a noticeable difference, and I will do the same as you suggested. Another note is that the audio volume is much different between them. The one with 09xx serial number is noticeably louder. When 09xx is set at the 9 o'clock position, 8xxx needs to be at 12 o'clock to have a comparable audio volume. Any help would be greatly appreciated. Thanks, Chris On Mon, Oct 7, 2024 at 10:19 AM David Hachadorian wrote: > It's probably the AGC settings. Here are my favorites: > agc dcy soft > hld 0.2 > pls nor > slp 000 > thr cw20, rtty17, ssb15 > f 200 > s 020 > > I have pf2 programmed to bring up agc thr, so I can change it when > switching modes. > > Dave Hachadorian, K6LL > Yuma, AZ > > > On 10/7/2024 6:24 AM, Chris wrote: > > Hello, > > I am a happy owner of K3. I came across another K3 with an early serial > number below 1000 in good condition at a local hamfest. It works well, > somehow better than my current K3, so my first reaction was, Wow. It seems > to have a lower noise floor and sounds slightly better. > > My question is, how can it be? I have yet to compare all the settings for > either radio. The filter in my current K3 is 2.7kHz, and the new (new to > me) K3 has 2.8kHz. I am not 100% sure these filters can make that much > difference. Besides that, all hardware configurations are pretty much the > same. They both have updated KSYN3A modules. This K3 with a lower serial > number has KAT3, and my current K3 doesn't because I have KAT500. > > Any suggestions? > > Many thanks, > > Chris KM1B > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to k6ll.d...@gmail.com > > > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to pari...@frontier.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 settings question
It is interesting to see the AGC THR makes a noticeable difference, and I will do the same as you suggested. Another note is that the audio volume is much different between them. The one with 09xx serial number is noticeably louder. When 09xx is set at the 9 o'clock position, 8xxx needs to be at 12 o'clock to have a comparable audio volume. Any help would be greatly appreciated. Thanks, Chris On Mon, Oct 7, 2024 at 10:19 AM David Hachadorian wrote: > It's probably the AGC settings. Here are my favorites: > agc dcy soft > hld 0.2 > pls nor > slp 000 > thr cw20, rtty17, ssb15 > f 200 > s 020 > > I have pf2 programmed to bring up agc thr, so I can change it when > switching modes. > > Dave Hachadorian, K6LL > Yuma, AZ > > > On 10/7/2024 6:24 AM, Chris wrote: > > Hello, > > I am a happy owner of K3. I came across another K3 with an early serial > number below 1000 in good condition at a local hamfest. It works well, > somehow better than my current K3, so my first reaction was, Wow. It seems > to have a lower noise floor and sounds slightly better. > > My question is, how can it be? I have yet to compare all the settings for > either radio. The filter in my current K3 is 2.7kHz, and the new (new to > me) K3 has 2.8kHz. I am not 100% sure these filters can make that much > difference. Besides that, all hardware configurations are pretty much the > same. They both have updated KSYN3A modules. This K3 with a lower serial > number has KAT3, and my current K3 doesn't because I have KAT500. > > Any suggestions? > > Many thanks, > > Chris KM1B > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to k6ll.d...@gmail.com > > > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 settings question
http://www.w3fpr.com/k3_agc.htm But disregard the 2012 firmware update link and use the current one from the Elecraft website (MCU 5.67 / DSP 2.88 / FPF 1.26, 1-22-2019) at https://elecraft.com/pages/k3s-high-performance-transceiver-firmware-and-utiliy 73, Kent K9ZTV On 10/7/2024 8:24 AM, Chris wrote: Hello, I am a happy owner of K3. I came across another K3 with an early serial number below 1000 in good condition at a local hamfest. It works well, somehow better than my current K3, so my first reaction was, Wow. It seems to have a lower noise floor and sounds slightly better. My question is, how can it be? I have yet to compare all the settings for either radio. The filter in my current K3 is 2.7kHz, and the new (new to me) K3 has 2.8kHz. I am not 100% sure these filters can make that much difference. Besides that, all hardware configurations are pretty much the same. They both have updated KSYN3A modules. This K3 with a lower serial number has KAT3, and my current K3 doesn't because I have KAT500. Any suggestions? Many thanks, Chris KM1B __ Elecraft mailing list Home:http://mailman.qth.net/mailman/listinfo/elecraft Help:http://mailman.qth.net/mmfaq.htm Post:mailto:Elecraft@mailman.qth.net This list hosted by:http://www.qsl.net Please help support this email list:http://www.qsl.net/donate.html Message delivered tok9...@socket.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 settings question
It's probably the AGC settings. Here are my favorites: agc dcy soft hld 0.2 pls nor slp 000 thr cw20, rtty17, ssb15 f 200 s 020 I have pf2 programmed to bring up agc thr, so I can change it when switching modes. Dave Hachadorian, K6LL Yuma, AZ On 10/7/2024 6:24 AM, Chris wrote: Hello, I am a happy owner of K3. I came across another K3 with an early serial number below 1000 in good condition at a local hamfest. It works well, somehow better than my current K3, so my first reaction was, Wow. It seems to have a lower noise floor and sounds slightly better. My question is, how can it be? I have yet to compare all the settings for either radio. The filter in my current K3 is 2.7kHz, and the new (new to me) K3 has 2.8kHz. I am not 100% sure these filters can make that much difference. Besides that, all hardware configurations are pretty much the same. They both have updated KSYN3A modules. This K3 with a lower serial number has KAT3, and my current K3 doesn't because I have KAT500. Any suggestions? Many thanks, Chris KM1B __ Elecraft mailing list Home:http://mailman.qth.net/mailman/listinfo/elecraft Help:http://mailman.qth.net/mmfaq.htm Post:mailto:Elecraft@mailman.qth.net This list hosted by:http://www.qsl.net Please help support this email list:http://www.qsl.net/donate.html Message delivered tok6ll.d...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 Settings for SignaLink USB
Many thanks to all of those who took the time and trouble to answer. I took the SignaLink apart and re-seated the module. I also re-checked my ALC setting and all the others on the rig. I had come across a very useful document by Jason K8ZT and followed his instructions to the letter. I also found the information by Don W3FPR immensely useful in setting up my ALC etc. All-in-all very helpful and I am now up and running on WSJT-X with no problems. I shall setup my FLDIGI next … Thanks again everyone and very 73, David G4NRT __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 Settings for SignaLink USB
You have the Signalink w/the module or the one w/jumpers? Several of my friends have had trouble w/the Signalink w/the module, I have two Signalinks, both w/jumpers and don’t have any issues. 73 de Jose Douglas KB1TCD Sent from my iPad > On Apr 4, 2020, at 4:21 AM, David Bondy wrote: > > I have been using digital modes for years and have a number of SignaLink USB > devices which have all worked very well with a variety of rigs. > > I am new to the K3 and have bought the Tigertronics cable and module set to > allow me to connect a SignaLink USB to the rear Line In/Out and PTT > connections on my K3. > > I am able to operate the rig (via a USB to RS232 cable for CAT) and transmit > JT8 signals (via the SignaLink) - I can see that I am getting out by > monitoring Hamspots! HOWEVER I am not able to get enough drive from the K3 > via the Signalink USB to decode incoming signals. > > Can someone who has this working please tell me what settings they have made > to the K3 in order to drive the SignaLink? I have set CONFIG > LIN OUT to > 100 and I have rotated the Rx knob to full clockwise on the SignaLink but I > am still not getting enough output to drive WSJT-X. I am sure that I am > missing something but I don’t know what because I would expect the LIN OUT > setting to be more like 10! > > Thanks in advance and 73, > > David G4NRT > > P.S. Please don’t bother to reply telling me to connect the rig to my PC > sound card … it doesn’t have one! > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to kb1...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 Settings for SignaLink USB
David, I think you should check the jumpers in the SignaLink. Also make certain the level controls for the SL soundcard are set correctly in the computer. Or simply use another USB soundcard - the K33 has built-in isolation transformers. Set the K3 LIN OUT level to about 10. You apparently have a problem, but it may not be in the K3. Plug amplified computer speakers into the K3 LINE OUT jack as a test. You should hear the sounds. 73, Don W3FPR On 4/4/2020 4:20 AM, David Bondy wrote: I have been using digital modes for years and have a number of SignaLink USB devices which have all worked very well with a variety of rigs. I am new to the K3 and have bought the Tigertronics cable and module set to allow me to connect a SignaLink USB to the rear Line In/Out and PTT connections on my K3. I am able to operate the rig (via a USB to RS232 cable for CAT) and transmit JT8 signals (via the SignaLink) - I can see that I am getting out by monitoring Hamspots! HOWEVER I am not able to get enough drive from the K3 via the Signalink USB to decode incoming signals. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 Settings for SignaLink USB
I ask “why use a SignaLink with the K3?” The K3 already has buffered Lin In and Line Out. Separate settings for in/out for each mode. The one item to pay attention to is transmit audio level. You should set the power out by using the Per knob on the K3 front panel. Then adjust the audio to show 4 solid bars and flashingbfifth bar on the ALC meter. Sent from my iPhone ...nr4c. bill > On Apr 4, 2020, at 4:22 AM, David Bondy wrote: > > I have been using digital modes for years and have a number of SignaLink USB > devices which have all worked very well with a variety of rigs. > > I am new to the K3 and have bought the Tigertronics cable and module set to > allow me to connect a SignaLink USB to the rear Line In/Out and PTT > connections on my K3. > > I am able to operate the rig (via a USB to RS232 cable for CAT) and transmit > JT8 signals (via the SignaLink) - I can see that I am getting out by > monitoring Hamspots! HOWEVER I am not able to get enough drive from the K3 > via the Signalink USB to decode incoming signals. > > Can someone who has this working please tell me what settings they have made > to the K3 in order to drive the SignaLink? I have set CONFIG > LIN OUT to > 100 and I have rotated the Rx knob to full clockwise on the SignaLink but I > am still not getting enough output to drive WSJT-X. I am sure that I am > missing something but I don’t know what because I would expect the LIN OUT > setting to be more like 10! > > Thanks in advance and 73, > > David G4NRT > > P.S. Please don’t bother to reply telling me to connect the rig to my PC > sound card … it doesn’t have one! > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to n...@widomaker.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 settings for Yamaha headset
Elecrafters, thanks for the input. -- Ohne CW ist es nur CB.. 73, Martin DM4iM __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 settings for Yamaha headset
On 10/24/2018 11:51 AM, Joe Subich, W4TV wrote: "Sharp and narrow" generally means too much high frequency (1600 - 3200 HZ) audio and not enough mid range (400 - 800 HZ) audio. Or that the other station is confusing ham radio with broadcasting. Some hams want to hear full bass -- that's fine if signals are strong with no QSB, but sucks power that can be better used for communication when conditions aren't great between you and your QSO partner. My recommended settings for most voices with the CM500 and other "flat" mics is for maximum cut of the three lowest bands (50, 100, 200), 6 dB cut of the 4th (400 Hz), the 7th band (2400 Hz) boosted 3 dB, and the 8th (3200 Hz) boosted 3-6 dB. On 10/24/2018 10:14 AM, Nate Bargmann wrote: Mic Gain 25 compression 10 NO! Numerical control settings are the WRONG way to set Mic Gain and Compression. Rather, Mic Gain should be set for full power on voice peaks with no compression. The "right" Mic Gain setting depends on how loud you talk and how close the mic is to your mouth. An ideal position for the mic is a few inches above and to the side of the mouth. This minimizes breath pops and allows drinking coffee and munching, but is also close enough to minimize room noise. Once that is "right," COMP should be set for indicated 10dB of Compression on the LED display on voice peaks. 73, Jim K9YC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 settings for Yamaha headset
> saying the audio is sharp and narrow . "Sharp and narrow" generally means too much high frequency (1600 - 3200 HZ) audio and not enough mid range (400 - 800 HZ) audio. With my CM-500 I use the following two sets of TX EQ: Normal operation "DX"/Contest Operation 50 -16 -16 100 -16 -16 200 - 8 - 8 4000 0 8000 0 1600 +3 +5 2400 +5 +8 3200 +6 +10 The "normal" EQ is very similar to a typical "communications" mic or the old Heil HC5 (3 dB/octave HF "boost") while the "DX" EQ is very similar to the Heil HC4 "DX" element (5 dB/octave HF "boost"). The DX/Contest setting is a bit "sharp" and I would not use it every day 73, ... Joe, W4TV On 2018-10-24 10:31 AM, Martin wrote: Elecrafters, i'm preparing the clubstation for the CQ WW Contest. I get Audio-reports saying the audio is sharp and narrow . I would like to set the K3 for a good and readable audio. Would the Yamaha CM 500 users share their settings? Thanks. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 settings for Yamaha headset
I've gotten good reports with the following: Mic Gain 25 compression 10 I set rear panel bias on for the electret element. My TX EQ is 0.05 -9 0.10 -6 0.20 0 0.40 +2 0.80 +4 1.60 +5 2.40 +2 3.20 -3 I use the same EQ settings for both the CM500 and for the MC-60 connected to the front panel connector. As I occasionally get good audio reports, these settings must be really doing something as I not only have a face for radio but a voice for CW and a fist for FT-8. ;-) 73, Nate, N0NB -- "The optimist proclaims that we live in the best of all possible worlds. The pessimist fears this is true." Web: http://www.n0nb.us GPG key: D55A8819 GitHub: N0NB __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 settings for Yamaha headset
Mic select rpl bias Mic gain 17 Cmp 17 Good place to start. Sent from my iPhone ...nr4c. bill > On Oct 24, 2018, at 10:31 AM, Martin wrote: > > Elecrafters, > i'm preparing the clubstation for the CQ WW Contest. I get Audio-reports > saying the audio is sharp and narrow . I would like to set the K3 for a good > and readable audio. Would the Yamaha CM 500 users share their settings? > Thanks. > > > > -- > > Ohne CW ist es nur CB.. > > 73, Martin DM4iM > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to n...@widomaker.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 settings for Yamaha headset
This article is for the KX3, but the TX EQ settings are from K3 users. I don’t know if the DVR trick works on the K3, but it is worth trying. https://observer.wunderwood.org/2015/09/09/transmit-audio-and-compression-with-the-elecraft-kx3/ wunder Walter Underwood wun...@wunderwood.org http://observer.wunderwood.org/ (my blog) > On Oct 24, 2018, at 7:31 AM, Martin wrote: > > Elecrafters, > i'm preparing the clubstation for the CQ WW Contest. I get Audio-reports > saying the audio is sharp and narrow . I would like to set the K3 for a good > and readable audio. Would the Yamaha CM 500 users share their settings? > Thanks. > > > > -- > > Ohne CW ist es nur CB.. > > 73, Martin DM4iM > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to wun...@wunderwood.org __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 Settings
Maybe I should dog off my "K line" control application and make an application to do this. Sent from my Verizon Wireless 4G LTE DROID Gary Hinson wrote: >I guess it would be possible to set some (if not all) of the configs on any >K3 using a suitable macro. Might be handy in a multi-station K3 contest >setup too I guess. > >73 >Gary ZL2iFB > >> -Original Message- >> From: elecraft-boun...@mailman.qth.net [mailto:elecraft- >> boun...@mailman.qth.net] On Behalf Of David F. Reed >> Sent: Monday, 4 March 2013 10:36 a.m. >> To: Jay >> Cc: Elecraft@mailman.qth.net >> Subject: Re: [Elecraft] K3 Settings >> >> My understanding is this: >> Unfortunately, no, only that K3. This is because the calibration settings >> unique to that radio are also part of what is saved / restored. >> I would love to see such a facility as well. >> >> 73 de Dave, W5SV >> >> On 3/3/13 3:33 PM, Jay wrote: >> > If I have a K3 on a network with a back up file for Settings, can this >> > file be used with the Utility for another K3 to set it up without >> > having to go through all the menus? >> >> __ >> >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html > > >-- >This message has been scanned for viruses and >dangerous content by MailScanner, and is >believed to be clean. > >__ >Elecraft mailing list >Home: http://mailman.qth.net/mailman/listinfo/elecraft >Help: http://mailman.qth.net/mmfaq.htm >Post: mailto:Elecraft@mailman.qth.net > >This list hosted by: http://www.qsl.net >Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Settings
Whoops. Wrong. NB and NR are not transferred to the Sub from main and can be set independently with BSET. Sorry. Fred Cady fcady at ieee dot org > -Original Message- > From: elecraft-boun...@mailman.qth.net [mailto:elecraft- > boun...@mailman.qth.net] On Behalf Of Cady, Fred > Sent: Sunday, March 03, 2013 5:11 PM > To: n...@arrl.net; Elecraft@mailman.qth.net > Subject: Re: [Elecraft] K3 Settings > > Hi Dave, > I'm pretty sure AGC, NB and NR are the same on the main and the sub rx. > Double tapping A>B sets the filter settings (and freqs) the same. You > can change the sub rx filter by holding BSET and then changing the > filter, for example. > Cheers and 73, > Fred KE7X > > Fred Cady > "The Elecraft K3: Design, Configuration and Operation Second Edition" > www.ke7x.com > > fcady at ieee dot org > > > -Original Message- > > From: elecraft-boun...@mailman.qth.net [mailto:elecraft- > > boun...@mailman.qth.net] On Behalf Of Dave Hawes > > Sent: Sunday, March 03, 2013 4:53 PM > > To: Elecraft@mailman.qth.net > > Subject: Re: [Elecraft] K3 Settings > > > > It is understood that you can't clone one K3 from another, but I have > > another > > question: > > > > Can you clone the Main RX to the SUB? I would like to be able to > make > > the > > SUB exactly like the MAIN, especially AGC, NB, Width, Shift, etc. It > > would be > > great if this could be done with a single command of some sort. > > > > 73 - Dave N3RD > > > > On 3 Mar 2013 at 15:35, David F. Reed wrote: > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Settings
Hi Dave, I'm pretty sure AGC, NB and NR are the same on the main and the sub rx. Double tapping A>B sets the filter settings (and freqs) the same. You can change the sub rx filter by holding BSET and then changing the filter, for example. Cheers and 73, Fred KE7X Fred Cady "The Elecraft K3: Design, Configuration and Operation Second Edition" www.ke7x.com fcady at ieee dot org > -Original Message- > From: elecraft-boun...@mailman.qth.net [mailto:elecraft- > boun...@mailman.qth.net] On Behalf Of Dave Hawes > Sent: Sunday, March 03, 2013 4:53 PM > To: Elecraft@mailman.qth.net > Subject: Re: [Elecraft] K3 Settings > > It is understood that you can't clone one K3 from another, but I have > another > question: > > Can you clone the Main RX to the SUB? I would like to be able to make > the > SUB exactly like the MAIN, especially AGC, NB, Width, Shift, etc. It > would be > great if this could be done with a single command of some sort. > > 73 - Dave N3RD > > On 3 Mar 2013 at 15:35, David F. Reed wrote: > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Settings
It is understood that you can't clone one K3 from another, but I have another question: Can you clone the Main RX to the SUB? I would like to be able to make the SUB exactly like the MAIN, especially AGC, NB, Width, Shift, etc. It would be great if this could be done with a single command of some sort. 73 - Dave N3RD On 3 Mar 2013 at 15:35, David F. Reed wrote: > My understanding is this: > Unfortunately, no, only that K3. This is because the calibration > settings unique to that radio are also part of what is saved / > restored. > I would love to see such a facility as well. > > 73 de Dave, W5SV > > On 3/3/13 3:33 PM, Jay wrote: > > If I have a K3 on a network with a back up file for Settings, can > this > > file be used with the Utility for another K3 to set it up without > > having to go through all the menus? > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: > http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Settings
Thanks All Sure would make it easy on the expedition to have one file sitting on the network that could be pulled..Oh well, back to PLAN A and save each setup to the specific laptop. Jay W2IJ - Original Message - From: "Tom H Childers" To: Sent: Sunday, March 03, 2013 3:21 PM Subject: Re: [Elecraft] K3 Settings No. The data is stored by K3 serial number. 73, Tom Amateur Radio Operator N5GE ARRL Lifetime Member QCWA Lifetime Member On Sun, 03 Mar 2013 13:33:11 -0800, "Jay" wrote: If I have a K3 on a network with a back up file for Settings, can this file be used with the Utility for another K3 to set it up without having to go through all the menus? __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Settings
No. The data is stored by K3 serial number. 73, Tom Amateur Radio Operator N5GE ARRL Lifetime Member QCWA Lifetime Member On Sun, 03 Mar 2013 13:33:11 -0800, "Jay" wrote: >If I have a K3 on a network with a back up file for Settings, can this file >be used with the Utility for another K3 to set it up without having to go >through all the menus? > > >__ >Elecraft mailing list >Home: http://mailman.qth.net/mailman/listinfo/elecraft >Help: http://mailman.qth.net/mmfaq.htm >Post: mailto:Elecraft@mailman.qth.net > >This list hosted by: http://www.qsl.net >Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Settings
I guess it would be possible to set some (if not all) of the configs on any K3 using a suitable macro. Might be handy in a multi-station K3 contest setup too I guess. 73 Gary ZL2iFB > -Original Message- > From: elecraft-boun...@mailman.qth.net [mailto:elecraft- > boun...@mailman.qth.net] On Behalf Of David F. Reed > Sent: Monday, 4 March 2013 10:36 a.m. > To: Jay > Cc: Elecraft@mailman.qth.net > Subject: Re: [Elecraft] K3 Settings > > My understanding is this: > Unfortunately, no, only that K3. This is because the calibration settings > unique to that radio are also part of what is saved / restored. > I would love to see such a facility as well. > > 73 de Dave, W5SV > > On 3/3/13 3:33 PM, Jay wrote: > > If I have a K3 on a network with a back up file for Settings, can this > > file be used with the Utility for another K3 to set it up without > > having to go through all the menus? > > __ > > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Settings
My understanding is this: Unfortunately, no, only that K3. This is because the calibration settings unique to that radio are also part of what is saved / restored. I would love to see such a facility as well. 73 de Dave, W5SV On 3/3/13 3:33 PM, Jay wrote: If I have a K3 on a network with a back up file for Settings, can this file be used with the Utility for another K3 to set it up without having to go through all the menus? __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Settings for a MH-2
Hi, I use mic gain 20, comp 20 with firmware 1.96/173. Don't forget to set mig gain L and bias on. Great reports. 73, John, W2GW - Original Message - From: "Patrick Taylor" <[EMAIL PROTECTED]> To: Sent: Friday, May 16, 2008 7:30 PM Subject: [Elecraft] K3 Settings for a MH-2 This has probably already been covered but I would like some suggestions of a good starting point for setting mic gain and compression for a MH-2 mic. Thanks, Pat W3HVG K3 834 K2 503 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com