Re: [Elecraft] KAT100 Tuning Failure
Since you have the KPA100 disconnected and the KAT100 connected to the KIO2 for control, the KAT100 with the K2 ATA menu in CAL, you can calibrate the KAT100 much like the KAT2 for wattmeter balance and forward power. Connect the K2 to the RF IN and a dummy load and inline wattmeter to ANT1. Set the power to 8 or 10 watts, and do a TUNE. Measure the voltage at U5 pin 5 and adjust C1 to achieve a minimum voltage - it should be close to zero volts. Then set R3 (forward trimmer pot) so the K2 display agrees with the power indicated on the external wattmeter. Since you do not have 25 ohm or 100 ohm dummy loads, power off the K2 and measure the resistance from U5 pin 3 to ground. Then multiply that resistance by 1.2 (remember that value). Then measure the resistance between U5 pin 3 to ground and adjust R4 to produce the resistance value you calculated. It does sound like you have things adjusted close to optimum, but a double check will do no harm. If you do find another dummy load to create a 25 ohm dully load, you can touch up the R4 (REFL) trimmer pot to properly indicate an SWR of 2.0. If by that time you have the KPA100 inline, you still can do it with the KPA100 "on it's back" to the right of the EC2 enclosure (supported on a boox or box about half the height of the enclosure). If you do it with the KPA100 inline, adjust R4 so the KAT100 LEDs indicate an SWR of 2.0 and ignore the K2 display. With the KPA100 inline, the K2 display will show the power and SWR seen by the KPA100 wattmeter, not the KAT100. 73, Don W3FPR On 8/10/2015 8:25 PM, JeremyJones wrote: Thanks Don. The KPA 100 is still disconnected. I have the base K2 with KAT2 connected to the KAT100 in the EC2 chassis. This normally has the KPA100 on top, but was removed as suggested to perform the troubleshooting. I don't have an extra dummy load at this time, but I am going to see if I can borrow one and test as you suggested. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KAT100 Tuning Failure
Thanks Don. The KPA 100 is still disconnected. I have the base K2 with KAT2 connected to the KAT100 in the EC2 chassis. This normally has the KPA100 on top, but was removed as suggested to perform the troubleshooting. I don't have an extra dummy load at this time, but I am going to see if I can borrow one and test as you suggested. -- View this message in context: http://elecraft.365791.n2.nabble.com/KAT100-Tuning-Failure-tp7605018p7606195.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KAT100 Tuning Failure
It sounds to me like all should be well. As a refinement --- If you have 2 50 ohm dummy loads and a coax TEE adapter, you could put the dummy loads in parallel to produce a 25 ohm dummy load. That will give you a sanity check on the Reflected trimmer pot calibration - adjust it to light the SWR=2 LED. Note that the power and SWR displayed on the K2 come from the KPA100 and not the KAT100. 73, Don W3FPR On 8/10/2015 6:14 PM, JeremyJones wrote: Ok, I received the new diodes today and have installed them into the KAT100. Running the tests in CAL mode has the LED indicators on the KAT100 matching what the display on the K2 reads, as well as matching the W2 watt meter. Is there anything else I should be looking at before starting to put things back together? __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KAT100 Tuning Failure
Ok, I received the new diodes today and have installed them into the KAT100. Running the tests in CAL mode has the LED indicators on the KAT100 matching what the display on the K2 reads, as well as matching the W2 watt meter. Is there anything else I should be looking at before starting to put things back together? -- View this message in context: http://elecraft.365791.n2.nabble.com/KAT100-Tuning-Failure-tp7605018p7606189.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KAT100 Tuning Failure
Parts are on order. I'll update once I have the diodes swapped. Thanks for the help thus far. -- View this message in context: http://elecraft.365791.n2.nabble.com/KAT100-Tuning-Failure-tp7605018p7605262.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KAT100 Tuning Failure
Jeremy, The wattmeter in the KAT100 has been damaged - diodes D1 and D2. You also have the KPA100, and it has a wattmeter with those diodes - so order 4 just in case those need to be replaced too. We can get to the KPA100 after the KAT100 has been taken care of. Failure to disconnect the antenna from the K2 when not in use will damage those diodes from static coning in from the feedline(s). 73, Don W3FPR On 7/20/2015 8:36 PM, JeremyJones wrote: Ok, redid the tests in CAL mode with the following results: 160M 1.03:1 No LED indication on KAT100. K2 showed 1.0:1 Hi Current warning 80M 1.03:1 No LED indication on KAT100. K2 showed 1.0:1 Hi Current warning 60M 1.02:1 No LED indication on KAT100. K2 showed 1.0:1 Hi Current warning 40M 1.03:1 LEDs on KAT100 lit up to 3. K2 showed 3.0:1 Hi Current warning 30M 1.03:1 LEDs on KAT100 lit up to 3. K2 showed 3.0:1 Hi Current warning 20M 1.00:1 LEDs on KAT100 lit up to 2.5. K2 showed 2.6:1 Hi Current warning 17M 1.04:1 LEDs on KAT100 lit up to 1.7. K2 showed 1.8:1 Hi Current warning 15M 1.04:1 LEDs on KAT100 lit up to 2. K2 showed 2.0:1 12M 1.05:1 LEDs on KAT100 lit up to 1.7. K2 showed 1.8:1 10M 1.06:1 LEDs on KAT100 lit up to 2. K2 showed 2.0:1 I guess ordering from Elecraft is the safest bet. It will take a bit longer, but so be it. -- View this message in context: http://elecraft.365791.n2.nabble.com/KAT100-Tuning-Failure-tp7605018p7605174.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to w3...@embarqmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KAT100 Tuning Failure
Ok, redid the tests in CAL mode with the following results: 160M 1.03:1 No LED indication on KAT100. K2 showed 1.0:1 Hi Current warning 80M 1.03:1 No LED indication on KAT100. K2 showed 1.0:1 Hi Current warning 60M 1.02:1 No LED indication on KAT100. K2 showed 1.0:1 Hi Current warning 40M 1.03:1 LEDs on KAT100 lit up to 3. K2 showed 3.0:1 Hi Current warning 30M 1.03:1 LEDs on KAT100 lit up to 3. K2 showed 3.0:1 Hi Current warning 20M 1.00:1 LEDs on KAT100 lit up to 2.5. K2 showed 2.6:1 Hi Current warning 17M 1.04:1 LEDs on KAT100 lit up to 1.7. K2 showed 1.8:1 Hi Current warning 15M 1.04:1 LEDs on KAT100 lit up to 2. K2 showed 2.0:1 12M 1.05:1 LEDs on KAT100 lit up to 1.7. K2 showed 1.8:1 10M 1.06:1 LEDs on KAT100 lit up to 2. K2 showed 2.0:1 I guess ordering from Elecraft is the safest bet. It will take a bit longer, but so be it. -- View this message in context: http://elecraft.365791.n2.nabble.com/KAT100-Tuning-Failure-tp7605018p7605174.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KAT100 Tuning Failure
Jeremy, Your first link resulted in an error 404, but the 2nd showed a diode that I believe may be a specialty version. It was highly overpriced at over $11 each. The Aligent data sheet for the 1N5711 shows it to be a 15 ma device. You would do better to order from Elecraft. Order E560004 - Diode, 1N5711, small glass body from pa...@elecraft.com. Order 2 of them (or possibly 4 since you do not yet know the status of those in the KPA100). An alternate source is "The Toroid King" http://www.partsandkits.com. Diz prices his 1N5711 diodes at 10 for $2 (plus shipping). I have purchased those diodes from Diz for a long time - never a problem. Yes, those test results are not valid unless the KAT100 was in CAL - in any other setting there would have been L and C elements active, and the goal is to test the wattmeter as the first step. 73, Don W3FPR On 7/20/2015 7:59 PM, JeremyJones wrote: The diodes I was looking at were 1N5711, but they were either 70V 15mA (http://www.digikey.ca/scripts/DkSearch/dksus.dll?Detail&itemSeq=176360177&uq=635730153536694158) or 70V 33mA (http://www.digikey.ca/product-search/en/discrete-semiconductor-products/diodes-rectifiers-single/1376383?k=1n5711). I just want to make sure I get one with the proper rating. I did not have the KAT100 in CAL mode. Guess I'll be redoing the tests and posting the results shortly. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KAT100 Tuning Failure
Jeremy, why not order the diodes from Elecraft and be sure you get the correct ones? 73! Ken - K0PP __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KAT100 Tuning Failure
The diodes I was looking at were 1N5711, but they were either 70V 15mA (http://www.digikey.ca/scripts/DkSearch/dksus.dll?Detail&itemSeq=176360177&uq=635730153536694158) or 70V 33mA (http://www.digikey.ca/product-search/en/discrete-semiconductor-products/diodes-rectifiers-single/1376383?k=1n5711). I just want to make sure I get one with the proper rating. I did not have the KAT100 in CAL mode. Guess I'll be redoing the tests and posting the results shortly. -- View this message in context: http://elecraft.365791.n2.nabble.com/KAT100-Tuning-Failure-tp7605018p7605170.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KAT100 Tuning Failure
Jeremy, Hopefully you had the ATU menu set to CAL for those tests. If not, please re-do the measurements. Assuming that you were set for ATU CAL, I can offer these comments: With the configuration you have now - KAT2 and KPA100 out of the picture, those results indicate that 1) the KAT100 wattmeter is not properly balanced and calibrated, or 2) something in the KAT100 wattmeter has been damaged - most likely diodes D1 and D2. It is possible that the diodes have been 'partially damaged' and have become frequency sensitive. With a dummy load connected and the ATU menu set to CAL, you should have a 1.0 SWR on all bands. The fact that you do not says that either the wattmeter is not properly balanced, or one or both diodes are bad, or that there is some random L/C element stuck in the path to he dummy load (that would be a relay problem). I would arbitrarily replace D1 and D2, and then attempt to balance and calibrate the KAT100 wattmeter as indicated in the KAT100 manual. If you cannot achieve a good null when balancing, just stop - attempting further steps is futile until you can obtain a good null. 73, Don W3FPR On 7/20/2015 7:15 PM, JeremyJones wrote: Ok, so I've removed the KPA100 completely, and disconnected the KAT2 serial and RF connections. I connected my W2 watt meter on the output of ANT2 of the KAT100, and the LOAD side of the sensor to a 50 ohm dummy load. The readings and indications I got are as follows: __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KAT100 Tuning Failure
Jeremy, Do not order alternatives for use in the wattmeters. Use only 1N5711s if you want the best voltage response vs. frequency. Those parameters are not specified. Elecraft chose those diodes long ago based on testing for that frequency response. If you are looking for alternatives, and do not care about the readings obtained at lower power levels (QRP), then you could use 1N4148 diodes which are plentiful. 73, Don W3FPR On 7/20/2015 7:31 PM, JeremyJones wrote: What are the specs for the diodes? I'm seeing 70V 15mA as the common size. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KAT100 Tuning Failure
What are the specs for the diodes? I'm seeing 70V 15mA as the common size. -- View this message in context: http://elecraft.365791.n2.nabble.com/KAT100-Tuning-Failure-tp7605018p7605166.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KAT100 Tuning Failure
Ok, so I've removed the KPA100 completely, and disconnected the KAT2 serial and RF connections. I connected my W2 watt meter on the output of ANT2 of the KAT100, and the LOAD side of the sensor to a 50 ohm dummy load. The readings and indications I got are as follows: 160M1.00:1 No LED indication on KAT100. K2 showed 1.0:1 80M 1.00:1 No LED indication on KAT100. K2 showed 1.0:1 60M 1.00:1 LEDs on KAT100 flickered a bit and remained off once tuning was finished. K2 showed 5.6:1 40M 1.00:1 LEDs on KAT100 flickered a bit and remained off once tuning was finished. K2 showed 5.6:1 30M 1.00:1 LEDs on KAT100 flickered a bit and finally lit 2. K2 showed 2.3:1 20M 1.00:1 LEDs on KAT100 lit as expected and finally lit 1. K2 showed 1.2:1 17M 1.00:1 LEDs on KAT100 lit as expected and finished at 1. K2 showed 1.0:1 15M 1.00:1 LEDs on KAT100 lit as expected and finished at 1. K2 showed 1.0:1 12M 1.05:1 LEDs on KAT100 lit as expected and finished at 1. K2 showed 1.0:1 10M 1.00:1 LEDs on KAT100 lit as expected and finished at 1. K2 showed 1.0:1 I'm still digging around for the diodes, but if I haven't found any by tomorrow I'll be putting in an order to digikey. -- View this message in context: http://elecraft.365791.n2.nabble.com/KAT100-Tuning-Failure-tp7605018p7605163.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KAT100 Tuning Failure
Jeremy, You must remove the ribbon cable to the KPA100 to remove it from the path - I suggest physically removing it from the EC2 enclosure just to be safe. The fact that you had the KPA100 partly in the path during your tests could create invalid observations. Use a dummy load for testing rather than an antenna. If you are getting funny SWR LED indications, the first suspect is D1 and D2 in the KAT100. Those are 1N5711 diodes, and if you have some in your parts supply, I would just replace them. I know it is a 'bear' to get to the solder side of the board when mounted in the EC2 enclosure, so see if there is enough lead length above the board to break the diodes and solder new ones in their place. You would get a better picture of the operation of the KAT100 wattmeter if you remove the KAT2 (just unplug it from the KIO2 AUX board). Then connect the KAT100 control cable and connect the K2 lower panel BNC to the KAT100 RF in. The KAT100 will then respond like the KAT2 normally does and in ATU CALP or CALS will show you the wattmeter readings - connect ANT1 to a dummy load for that test. It is advisable to connect an inline wattmeter between the KAT100 and the dummy load. If the internal wattmeter in the KAT100 is not functioning properly you will be able to calibrate it. 73, Don W3FPR On 7/17/2015 1:05 PM, JeremyJones wrote: After many months of flawless operation, my KAT100 is starting to have trouble tuning up, particularly on 40 and 80M. It even has trouble tuning up a 50 ohm dummy load on these bands. My normal setup is a 10W K2 with a KAT2, connected on the ANT 1 port to the AUX RF port of the KAT100 (mounted in an EC2 case with the KPA100). This is internally connected to the KPA100. The RF out from the KPA100 is then connected to the RF IN on the KAT100. ANT 1 is connected to a DX-CC and ANT 2 is connected to an 80M Carolina Windom. The first signs of trouble started when the SWR LEDs only lit intermittently. The ANTENNA and PWR RANGE LEDs lit and operated correctly. Gradually I stared seeing higher and higher SWR readings. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KAT100 Tuning Failure
Be sure to check all the cables or try changing them out one by one, Jeremy. Phil W7OX On 7/17/15 10:05 AM, JeremyJones wrote: After many months of flawless operation, my KAT100 is starting to have trouble tuning up, particularly on 40 and 80M. It even has trouble tuning up a 50 ohm dummy load on these bands. My normal setup is a 10W K2 with a KAT2, connected on the ANT 1 port to the AUX RF port of the KAT100 (mounted in an EC2 case with the KPA100). This is internally connected to the KPA100. The RF out from the KPA100 is then connected to the RF IN on the KAT100. ANT 1 is connected to a DX-CC and ANT 2 is connected to an 80M Carolina Windom. The first signs of trouble started when the SWR LEDs only lit intermittently. The ANTENNA and PWR RANGE LEDs lit and operated correctly. Gradually I stared seeing higher and higher SWR readings. In order to narrow down the issue, I removed the KPA100 from the setup by connecting the KAT2 ANT 1 port directly to the KAT100 RF IN. I disconnected the power from the KPA100 and independently powered the KAT100. I removed the Windom from ANT 2 and connected a 50 ohm dummy load to see how the tuning compared with the antenna and the dummy load. On 80M the dummy load gets 3:1 SWR with the DX-CC tuning up the same. 60M gets 2.3:1 for both. 40M gets 1.2 for the dummy load and 3:1 for the DX-CC. 30M and up seem to tune ok. I tried doing the troubleshooting steps in the manual, starting with ATU INIT. I scrolled through L0-L8 and C0-C8 and N1-N2 and the relays functioned for each. I tried doing the individual test for the inductors and relays, but there was no change in SWR with multiple components, so either I was doing it wrong, or the fault is bigger than a single component. I've tried to be as detailed as possible here, so any help is appreciated, and if there are any suggestions or any other info required please let me know. I'd like to get this back on the air as its my only radio! __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
