[Flexradio] Odd signal while TX using CWX
Hi Group: I just noticed that when I TX on CW using CWX on PowerSDR Beta 2.0.16 I get the CW peak on the correct TX freq but I also see a signal on the PANAFALL which is about 40db and 3 KHZ wide. Could this be that I am getting a signal from another AF source. Which setup button should I change to get the common gauss curve which peaks at the TX freq? 73´s Mario ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/
Re: [Flexradio] Odd signal while TX using CWX
Hi David: Thank you for your response. I disconnected all mics from the radio and I still get 3 khz wide constant signal and the CW peak on the TX freq. I guess there is another signal source which I cannot locate. BTW, VAC is off 73´s Mario - Original Message - From: David Walker vk...@bigpond.com To: Mario Aviles mario.avi...@amnetsal.com Sent: Saturday, January 29, 2011 7:05 PM Subject: Re: [Flexradio] Odd signal while TX using CWX Hi Mario ...And if you talk into your microphone it will appear as though you are modulating SSB. I found that by disconnecting the mic while in CW will stop any movement on the panadaptor while in CW TX mode. Regards, Dave On 30/01/2011 10:44 AM, Mario Aviles wrote: Hi Group: I just noticed that when I TX on CW using CWX on PowerSDR Beta 2.0.16 I get the CW peak on the correct TX freq but I also see a signal on the PANAFALL which is about 40db and 3 KHZ wide. Could this be that I am getting a signal from another AF source. Which setup button should I change to get the common gauss curve which peaks at the TX freq? 73´s Mario ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/
[Flexradio] Help with PSDR 2.0
Hi: This mornig I decided to install PSDR 2.0 Beta, performed all steps as per instructions and got the same error message on both installation attemps. The message I am getting is the following: Erro Communicating with radio, the program will likely crash Please update the radio firmware to V2.0+ to prevent this issue Firware is available at our webpage www.flex. I tried to locate a radio firmware version 2.0 but could no find it, mine is 1.3.0.8. I rolled back to version 1.18.6 without any problem Any suggestions? 73´s Mario/YS1MAE ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] Help with PSDR 2.0
Neil and Tim: Solved the problem, thanks for help. PSDR2.0 is great 73´s Mario - Original Message - From: Tim Ellison telli...@itsco.com To: Mario Aviles mario.avi...@amnetsal.com; flexradio@flex-radio.biz Sent: Sunday, July 18, 2010 2:39 PM Subject: RE: [Flexradio] Help with PSDR 2.0 Uninstall your Firewire driver before running the PowerSDR v2.0 Beta I tried to locate a radio firmware version 2.0 but could no find it, mine is 1.3.0.8. Try the Knowledge Center http://kc.flex-radio.com/KnowledgebaseArticle50441.aspx -Tim - W4TME -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Mario Aviles Sent: Sunday, July 18, 2010 4:32 PM To: flexradio@flex-radio.biz Subject: [Flexradio] Help with PSDR 2.0 Hi: This mornig I decided to install PSDR 2.0 Beta, performed all steps as per instructions and got the same error message on both installation attemps. The message I am getting is the following: Erro Communicating with radio, the program will likely crash Please update the radio firmware to V2.0+ to prevent this issue Firware is available at our webpage www.flex. I tried to locate a radio firmware version 2.0 but could no find it, mine is 1.3.0.8. I rolled back to version 1.18.6 without any problem Any suggestions? 73´s Mario/YS1MAE ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/
[Flexradio] PSDR Ver 2.00
Hi Group: I know this question has been asked before but here it goes anyways. Any idea when PSDR version 2.00 will be out as official version? 73´s Mario/YS1MAE !Navega con el Internet Gratis de AmNet! Descarga el Programa de Instalación. Visítanos en www.amnetcable.com Para cualquier consulta llamanos al 2207-4000 ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] 2.0
Hi Where did you get it? Nothing on the official Website 73´s MarioYS1MAE - Original Message - From: adam grossmyer agg...@gmail.com To: flexradio@flex-radio.biz Sent: Wednesday, May 26, 2010 9:09 PM Subject: [Flexradio] 2.0 I got to say, I am loving 2.0 so far. 73 Adam N8MOX ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] Congrats to Simon HB9DRV
Congratulations Simon, excellent product, excellent support, great contribution to make hamradio a lot more fun. An award well deserved 73´s Mario/YS1MAE El Sat, 27 Mar 2010 08:52:12 EDT harryh...@aol.com ha escrito: My congratulations also to Simon HB9DRV. Ham Radio Deluxe is a work of art He deserves the award for this software!! Harry W9BR In a message dated 3/26/2010 11:00:49 A.M. Central Daylight Time, flexradio-requ...@flex-radio.biz writes: For those of you who have not heard, Simon HB9DRV will receive the 2010 ARRL Technical Achievement award at the Dayton Hamfest in May for his work on Ham Radio Deluxe. Many congratulations, Simon! Geep WA4RTS ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ !Navega con el Internet Gratis de AmNet! Descarga el Programa de Instalación. Visítanos en www.amnetcable.com Para cualquier consulta llamanos al 2207-4000 ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] Flex3000 No SWR Reading?
Hi All: My 5000A does the same thing, I remember asking this same question when I first noticed this and was told this is OK, not to worry. Try using the TUNE button and set the meter to SWR, then you´ll see the correct SWR reading. Mario - Original Message - From: Larry da Ponte n7bcp.la...@gmail.com To: Mike Tatum m...@f5vkm.com Cc: flexradio@flex-radio.biz Sent: Sunday, February 14, 2010 11:20 AM Subject: Re: [Flexradio] Flex3000 No SWR Reading? Hi Mike. I'm observing the same swr meter reading you are even on SSB -Larry On Feb 14, 2010, at 9:09 AM, Mike Tatum m...@f5vkm.com wrote: Hi All, I've finally got my brand new Flex3000 on air and have to say I am very pleased with the receiver performance! The filtering on CW is truly amazing! So my first real question to the group :) Flex3000 PSDR v1.18.5 FW Driver v3.5.0.7171 F3K Firmware v1.2.5.6 in PSDR you can set the meter to read SWR during TX, which I have done, however regardless of the real SWR as measured on my SWR meter connected inline, the PSDR SWR reading is always 0.0:1, however if I set the meter to REFPWR it shows a power reading when the SWR is high, IE: 2:1 which is correct. So can someone please do the same test and see if they get the same result, IE: the PSDR SWR reading is always 0.0:1? If it works for you guys then perhaps my new F3K is faulty? I hope not, although the first one from the UK importer was DOA! I look forward to hearing from you. Thanks. Mike M0AWS / F5VKM http://www.f5vkm.com ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] Flex 5K locking up
Hi Group: Now I don´t know what happened, after I did these changes now I dont have audio and I get a strange signal on TX no power out. The unit is receiving I can see that on the pan display as I move frecuencies but no audio out Any ideas? Mario - Original Message - From: Dudley Hurry jhu...@austin.rr.com To: Mario Aviles mario.avi...@amnetsal.com Cc: flexradio@flex-radio.biz Sent: Friday, January 29, 2010 11:36 PM Subject: Re: [Flexradio] Flex 5K locking up Mario, You said your latency is 15119us?? You should get the latency below 2000us to be consistent, some have gotten core2Duos to run under 100us. Be sure to turn the Wireless and bluetooth drivers off, and make sure your Power Options in the control panel is set to High Performance. Other than that.. What are the details? Of the system and what versions of PowerSDR and FW are you trying to run? 73, Dudley WA5QPZ Mario Aviles wrote: Hi Group: I know this question has been asked before but I could not find the answer so here it goes, My Flex 5K was running ok, some lockups once in a while but not as bad as now that when the DX summit page is refreshed or while surfing the web it happens. (it happened several times while writing this email) Two changes since that time, installed DDUtil and installed a new two monitor graphics card. (Radeon HD 4650 1GB GDDR2 Memory) Running Windows Vista 32 bit SP2 HP Pavillion Intel Core 2 Duo CPU 2.00GB RAM Flex setup 96KHZ buffer size 2048 Safe level 3 (latency (max) 15119us) Any suggestions besides changing computer? 73´s Mario/YS1MAE ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] Flex 5K locking up
Hi Neal: What I show is the following: PCI 20 AGERE HOST COntroller OHCI compatible with IEEE1394 PCI 20 Netwrok connection Intel (R) PRO /100 VE Let me know if this helps Mario/YS1MAE - Original Message - From: Neal Campbell To: Mario Aviles Cc: Tim Ellison ; Dudley Hurry ; flexradio@flex-radio.biz Sent: Saturday, January 30, 2010 6:40 PM Subject: Re: [Flexradio] Flex 5K locking up Go to your control panel, double-click on System and when that window pops up, go to the Hardware tab, then click on the button called Device Manager. When the device manager window appears, go to the views menu at the top of the window and select View by Connection. When this display appears, click on the plus sign by the IRQ line, When the list of devices, sorted by the interrupt (IRQ) appears, look for your firewire card. To the left of it will be a number which is the interrupt number assigned to your fiirewire card. Tell us what other devices have the same number besides them as your firewire card. That could help us tremendously! 73 Neal Campbell Abroham Neal Software www.abrohamnealsoftware.com (540) 645 5394 NEW PHONE NUMBER Amateur Radio: K3NC Blog: http://www.abrohamnealsoftware.com/blog/ DXBase bug reports: email to ca...@dxbase.fogbugz.com Abroham Neal forums: http:/www.abrohamnealsoftware.com/community/ On Sat, Jan 30, 2010 at 6:42 PM, Mario Aviles mario.avi...@amnetsal.com wrote: Hi Tim: Did that and no change, I was thinking about uninstalling everything, firewire driver, PSDR and starting from scratch. 73´s Mario - Original Message - From: Tim Ellison telli...@itsco.com To: Mario Aviles mario.avi...@amnetsal.com; Dudley Hurry jhu...@austin.rr.com Cc: flexradio@flex-radio.biz Sent: Saturday, January 30, 2010 5:33 PM Subject: RE: [Flexradio] Flex 5K locking up Try resetting your database. -Tim -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Mario Aviles Sent: Saturday, January 30, 2010 6:27 PM To: Dudley Hurry Cc: flexradio@flex-radio.biz Subject: Re: [Flexradio] Flex 5K locking up Hi Group: Now I don´t know what happened, after I did these changes now I dont have audio and I get a strange signal on TX no power out. The unit is receiving I can see that on the pan display as I move frecuencies but no audio out Any ideas? Mario - Original Message - From: Dudley Hurry jhu...@austin.rr.com To: Mario Aviles mario.avi...@amnetsal.com Cc: flexradio@flex-radio.biz Sent: Friday, January 29, 2010 11:36 PM Subject: Re: [Flexradio] Flex 5K locking up Mario, You said your latency is 15119us?? You should get the latency below 2000us to be consistent, some have gotten core2Duos to run under 100us. Be sure to turn the Wireless and bluetooth drivers off, and make sure your Power Options in the control panel is set to High Performance. Other than that.. What are the details? Of the system and what versions of PowerSDR and FW are you trying to run? 73, Dudley WA5QPZ Mario Aviles wrote: Hi Group: I know this question has been asked before but I could not find the answer so here it goes, My Flex 5K was running ok, some lockups once in a while but not as bad as now that when the DX summit page is refreshed or while surfing the web it happens. (it happened several times while writing this email) Two changes since that time, installed DDUtil and installed a new two monitor graphics card. (Radeon HD 4650 1GB GDDR2 Memory) Running Windows Vista 32 bit SP2 HP Pavillion Intel Core 2 Duo CPU 2.00GB RAM Flex setup 96KHZ buffer size 2048 Safe level 3 (latency (max) 15119us) Any suggestions besides changing computer? 73´s Mario/YS1MAE ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Re: [Flexradio] Flex 5K locking up
Indeed, I noticed that it locked up when accesing the internet or mail program. The latency is around 2000 and this is normal from before I ade the changes. Is there a way to change the IRQ on the network card? I would like to access the Internet on this computer. Yes, I am using RJ45 Mario - Original Message - From: Neal Campbell To: Mario Aviles Cc: Tim Ellison ; Dudley Hurry ; flexradio@flex-radio.biz Sent: Saturday, January 30, 2010 9:18 PM Subject: Re: [Flexradio] Flex 5K locking up It does, you are sharing the interrupt with your lan port. I assume you are using the RJ45 plug in the motherboard? You can try to disable it and use a USB wifi stick (or not use the internet at all), If you need help on how to disable it, let me know! Neal Campbell Abroham Neal Software www.abrohamnealsoftware.com (540) 645 5394 NEW PHONE NUMBER Amateur Radio: K3NC Blog: http://www.abrohamnealsoftware.com/blog/ DXBase bug reports: email to ca...@dxbase.fogbugz.com Abroham Neal forums: http:/www.abrohamnealsoftware.com/community/ On Sat, Jan 30, 2010 at 9:45 PM, Mario Aviles mario.avi...@amnetsal.com wrote: Hi Neal: What I show is the following: PCI 20 AGERE HOST COntroller OHCI compatible with IEEE1394 PCI 20 Netwrok connection Intel (R) PRO /100 VE Let me know if this helps Mario/YS1MAE - Original Message - From: Neal Campbell To: Mario Aviles Cc: Tim Ellison ; Dudley Hurry ; flexradio@flex-radio.biz Sent: Saturday, January 30, 2010 6:40 PM Subject: Re: [Flexradio] Flex 5K locking up Go to your control panel, double-click on System and when that window pops up, go to the Hardware tab, then click on the button called Device Manager. When the device manager window appears, go to the views menu at the top of the window and select View by Connection. When this display appears, click on the plus sign by the IRQ line, When the list of devices, sorted by the interrupt (IRQ) appears, look for your firewire card. To the left of it will be a number which is the interrupt number assigned to your fiirewire card. Tell us what other devices have the same number besides them as your firewire card. That could help us tremendously! 73 Neal Campbell Abroham Neal Software www.abrohamnealsoftware.com (540) 645 5394 NEW PHONE NUMBER Amateur Radio: K3NC Blog: http://www.abrohamnealsoftware.com/blog/ DXBase bug reports: email to ca...@dxbase.fogbugz.com Abroham Neal forums: http:/www.abrohamnealsoftware.com/community/ On Sat, Jan 30, 2010 at 6:42 PM, Mario Aviles mario.avi...@amnetsal.com wrote: Hi Tim: Did that and no change, I was thinking about uninstalling everything, firewire driver, PSDR and starting from scratch. 73´s Mario - Original Message - From: Tim Ellison telli...@itsco.com To: Mario Aviles mario.avi...@amnetsal.com; Dudley Hurry jhu...@austin.rr.com Cc: flexradio@flex-radio.biz Sent: Saturday, January 30, 2010 5:33 PM Subject: RE: [Flexradio] Flex 5K locking up Try resetting your database. -Tim -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Mario Aviles Sent: Saturday, January 30, 2010 6:27 PM To: Dudley Hurry Cc: flexradio@flex-radio.biz Subject: Re: [Flexradio] Flex 5K locking up Hi Group: Now I don´t know what happened, after I did these changes now I dont have audio and I get a strange signal on TX no power out. The unit is receiving I can see that on the pan display as I move frecuencies but no audio out Any ideas? Mario - Original Message - From: Dudley Hurry jhu...@austin.rr.com To: Mario Aviles mario.avi...@amnetsal.com Cc: flexradio@flex-radio.biz Sent: Friday, January 29, 2010 11:36 PM Subject: Re: [Flexradio] Flex 5K locking up Mario, You said your latency is 15119us?? You should get the latency below 2000us to be consistent, some have gotten core2Duos to run under 100us. Be sure to turn the Wireless and bluetooth drivers off, and make sure your Power Options in the control panel is set to High Performance. Other than that.. What are the details? Of the system and what versions of PowerSDR and FW are you trying to run? 73, Dudley WA5QPZ Mario Aviles wrote: Hi Group: I know this question has been asked before but I could not find the answer so here it goes, My Flex 5K was running ok, some lockups once in a while but not as bad as now that when the DX
Re: [Flexradio] Flex 5K locking up
I checked and there is no other PCI slot and the 1394 port is inborad. I guess I am doomed? Mario/YS1MAE - Original Message - From: Neal Campbell To: Mario Aviles Cc: Tim Ellison ; Dudley Hurry ; flexradio@flex-radio.biz Sent: Saturday, January 30, 2010 9:32 PM Subject: Re: [Flexradio] Flex 5K locking up There is no way to change the IRQ, you are stuck with it. If there is another pci slot in your computer (and assuming that you are using a non-onboard firewire port), move your card and then see if/what IRQ it shares a device with. The USB wifi stick is still a good alternative though! Neal Campbell Abroham Neal Software www.abrohamnealsoftware.com (540) 645 5394 NEW PHONE NUMBER Amateur Radio: K3NC Blog: http://www.abrohamnealsoftware.com/blog/ DXBase bug reports: email to ca...@dxbase.fogbugz.com Abroham Neal forums: http:/www.abrohamnealsoftware.com/community/ On Sat, Jan 30, 2010 at 10:24 PM, Mario Aviles mario.avi...@amnetsal.com wrote: Indeed, I noticed that it locked up when accesing the internet or mail program. The latency is around 2000 and this is normal from before I ade the changes. Is there a way to change the IRQ on the network card? I would like to access the Internet on this computer. Yes, I am using RJ45 Mario - Original Message - From: Neal Campbell To: Mario Aviles Cc: Tim Ellison ; Dudley Hurry ; flexradio@flex-radio.biz Sent: Saturday, January 30, 2010 9:18 PM Subject: Re: [Flexradio] Flex 5K locking up It does, you are sharing the interrupt with your lan port. I assume you are using the RJ45 plug in the motherboard? You can try to disable it and use a USB wifi stick (or not use the internet at all), If you need help on how to disable it, let me know! Neal Campbell Abroham Neal Software www.abrohamnealsoftware.com (540) 645 5394 NEW PHONE NUMBER Amateur Radio: K3NC Blog: http://www.abrohamnealsoftware.com/blog/ DXBase bug reports: email to ca...@dxbase.fogbugz.com Abroham Neal forums: http:/www.abrohamnealsoftware.com/community/ On Sat, Jan 30, 2010 at 9:45 PM, Mario Aviles mario.avi...@amnetsal.com wrote: Hi Neal: What I show is the following: PCI 20 AGERE HOST COntroller OHCI compatible with IEEE1394 PCI 20 Netwrok connection Intel (R) PRO /100 VE Let me know if this helps Mario/YS1MAE - Original Message - From: Neal Campbell To: Mario Aviles Cc: Tim Ellison ; Dudley Hurry ; flexradio@flex-radio.biz Sent: Saturday, January 30, 2010 6:40 PM Subject: Re: [Flexradio] Flex 5K locking up Go to your control panel, double-click on System and when that window pops up, go to the Hardware tab, then click on the button called Device Manager. When the device manager window appears, go to the views menu at the top of the window and select View by Connection. When this display appears, click on the plus sign by the IRQ line, When the list of devices, sorted by the interrupt (IRQ) appears, look for your firewire card. To the left of it will be a number which is the interrupt number assigned to your fiirewire card. Tell us what other devices have the same number besides them as your firewire card. That could help us tremendously! 73 Neal Campbell Abroham Neal Software www.abrohamnealsoftware.com (540) 645 5394 NEW PHONE NUMBER Amateur Radio: K3NC Blog: http://www.abrohamnealsoftware.com/blog/ DXBase bug reports: email to ca...@dxbase.fogbugz.com Abroham Neal forums: http:/www.abrohamnealsoftware.com/community/ On Sat, Jan 30, 2010 at 6:42 PM, Mario Aviles mario.avi...@amnetsal.com wrote: Hi Tim: Did that and no change, I was thinking about uninstalling everything, firewire driver, PSDR and starting from scratch. 73´s Mario - Original Message - From: Tim Ellison telli...@itsco.com To: Mario Aviles mario.avi...@amnetsal.com; Dudley Hurry jhu...@austin.rr.com Cc: flexradio@flex-radio.biz Sent: Saturday, January 30, 2010 5:33 PM Subject: RE: [Flexradio] Flex 5K locking up Try resetting your database. -Tim -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Mario Aviles Sent: Saturday, January 30, 2010 6:27 PM To: Dudley Hurry Cc: flexradio@flex-radio.biz Subject: Re: [Flexradio] Flex 5K locking up Hi Group: Now I don´t know what happened, after I did these changes now I dont have audio and I
[Flexradio] Flex 5K locking up
Hi Group: I know this question has been asked before but I could not find the answer so here it goes, My Flex 5K was running ok, some lockups once in a while but not as bad as now that when the DX summit page is refreshed or while surfing the web it happens. (it happened several times while writing this email) Two changes since that time, installed DDUtil and installed a new two monitor graphics card. (Radeon HD 4650 1GB GDDR2 Memory) Running Windows Vista 32 bit SP2 HP Pavillion Intel Core 2 Duo CPU 2.00GB RAM Flex setup 96KHZ buffer size 2048 Safe level 3 (latency (max) 15119us) Any suggestions besides changing computer? 73´s Mario/YS1MAE ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/
[Flexradio] Exchanging CAT data between two computers.
Hi Group: I have a Flex 5000A and I am using a HP Pavillion computer running under Windows Vista. This OS has been Ok so far, running PSDR and through virtual COM Ports running DXLab logging program. Problems began yesterday when I tried to connect a Startech USB to 4 RS232 converter to run my linear, antenna etc. There is a problem with the drivers since this converter runs fine on my XP. I contacted the manufacturer and apparantly they dont have a solution for this yet. One idea that occured to me is to run PSDR on the Pavillion (VISTA) and run the peripherals off my other XP computer. The question is, is there a way to send CAT data from PSDR from one computer to the other since I would be running the logging program on the other computer? 73's Mario/YS1MAE ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to arch...@mail-archive.com
[Flexradio] Flex 5KA with Expert 1K-FA linear
Hi group: Just ordered the Expert 1K-FA linear and its on its way. Anybody that has the same setup that can share information on how to setup the CAT interface? 73´s Mario/YS1MAE ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to arch...@mail-archive.com
[Flexradio] Flex 5K with Palstar AT-AUTO Tuner
Hi Group: I am trying to interface my Flex 5K with a Palstar AT_Auto Tuner. Can somebody help? 73´s Mario/ YS1MAE ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/
[Flexradio] offer for current flexers?
Hi: Interesting bundled promotions Flexradio is offering to a potential new Flexer, but are there any offers for us current Flexers? Like a very special price on RX2 board? 73's Mario/YS1MAE ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/