Re: [Flexradio] SSB Tx Audio Punch
What I am about to write may not be very popular, and I am likely to be shot down in flames. Please believe me that I mean no offence, and would just like to share an opinion that has been developed over many years of HF SSB operation, both on the amateur bands and on military HF comms circuits. While the new SDR world brings many huge advantages to the radio experimenter, we must be very careful not to throw the baby out with the bath water when we discard analogue techniques. IMO, the speech processing area represents the very crown jewels of an HF radio transmitter, as it is critical to the overall operation of the radio. I therefore believe that developers should be very careful when they tinker in this area, and such work should not be undertaken lightly. Before presenting new code for evaluation, the following bench testing should be done. (On the air testing is VERY time consuming, and requires contacts under the right propagation conditions which are not always available) Test 1. Adjust the OUTPUT level on the UUT (unit under test) to give the required peak output power while whistling into the mic Use an average reading power meter. Then say "aargh" into the mic, and adjust the INPUT level for half of this power. Eg, 100W indicated for a whistle, and 50W for "aargh". Then go back to the whistle if necessary, and re-adjust the OUTPUT for 100W. Iterate as necessary to achieve both these results. For an RF clipper, this represents approximately 15 dB of clipping. If this 2:1 power ratio cannot be achieved, then the UUT fails the first test. Note the input level for the whistle using a scope. Test 2. Using an audio signal generator at a frequency of 700 Hz, feed in the same level into the UUT as the mic was giving for a whistle. Do NOT adjust the input or output levels of the UUT. Check the output of the radio on a spectrum analyser, and ensure that the products at 1400 Hz and 2100 Hz offset are at least 30 dB down. This can also be done at some intermediate test point if available. If both the above tests pass, then it is worth while to try some on air testing. The other parameter that affects on air intelligibility is audio frequency response. The mic itself should peak at about 1 kHz (eg Shure 444), and there should be ADDITIONAL electronic pre-emphasis with a time constant of about 160 us. This gives a roll-off below 1 kHz of 6 dB per octave. Many operators (especially the "AM HiFi bunch") will hate what I have said, but under difficult weak signal conditions, a radio performing as above will give the most intelligible signal. From a performance point of view, it really doesn't matter whether this is achieved by analogue processing external to the radio, or internally in DSP. The result will be the same if the correct principles are followed. In my experience, it is very difficult to achieve these results with processing performed at baseband. Envelope tracking comes the closest. In principle they are easier to achieve with IF/RF processing. 73, Greg, ZL3IX Ian Scoble wrote: > > > > > Please can anyone else confirm whether they are having audio punch problems > on SSB, the problem seems to have occurred since the SVN upgrade on or > around 1840. I did put a bug up on the board but this seems to have been > deleted other people I know are having the same problem and I was wondering > how wide spread it is. > > > > Thanks Ian G0CTO > > > > ___ > FlexRadio Systems Mailing List > FlexRadio@flex-radio.biz > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kb.flex-radio.com/ Homepage: > http://www.flex-radio.com/ > > > ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] SSB Tx Audio Punch
On 05/01/2008, Greg - ZL3IX <[EMAIL PROTECTED]> wrote: > I am still using a very old SVN with my HPSDR, so have not experienced > these recent problems. Personally, I am in favour of using the envelope > tracker, which I believe is implemented in COMP, rather than CPDR. The > envelope tracker seems to be the closest we get to analogue RF clipping, > which is still my favourite. I do not like companding, as it is very > difficult to obtain enough compression without introducing harmonic > distortion, which detracts from intelligibility on DX contacts. > > I am toying with the idea of not using any compression with PowerSDR, > and using an outboard RF clipper, either analogue RF, or possibly the > software version by Alex, VE3NEA. Unfortunately, my own coding skills > are not adequate, or I would be writing a DSP version of an RF clipper > myself, and offering it to the project. Does anyone with better skills > than mine feel like trying that? > > 73, Greg, ZL3IX Greg, Unfortunately I am in the same situation with you - no software skills. Since early 70's I'm using so called RF clipper (home built) in the IF chain of all Japanese transceivers I have had. So far some earlier and short transmitting trials have not made me convinced about the correct function of the SSB process of the PowerSDR, so I have refused to use otherwise so excellent SDR-1000 for transmitting. I want to admit, that during the last few months I have not tried any new SVNs. However, after some private communication with John, W5GI, I believe that FlexRadio finally understands what kind of "DX-sound" we need and want. Maybe, SVN1875 already is good. I am still waiting that the version will be reasonably bugfree and suggested settings will be given with good explanations in the Knowledge Base. Just some more patience and FlexRadio will do that! 73, Ahti OH2RZ > ___ > FlexRadio Systems Mailing List > FlexRadio@flex-radio.biz > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kb.flex-radio.com/ Homepage: > http://www.flex-radio.com/ > > ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] SSB Tx Audio Punch
One thing I left out, with the changes-- in SVN versions it is recommended you start with a new database. I recommend trying SVN 1875. John P. Basilotto W5GI Chief Operating Officer Marketing and Sales Office 512-535-5266 Fax512-233-5143 www.flex-radio.com -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Doug McCann Sent: Saturday, January 05, 2008 10:00 AM To: [EMAIL PROTECTED]; 'Ian Scoble'; flexradio@flex-radio.biz Subject: Re: [Flexradio] SSB Tx Audio Punch I too have the "Audio Punch" problem. I tried to roll back to 1836 and ran into a lot of error messages. For now, I have settled for the official download 10.1.3 which fixed the audio problem. FYI only Doug, VA3CR www.va3cr.net -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of ON9CDY Sent: January-05-08 6:24 AM To: 'Ian Scoble'; flexradio@flex-radio.biz Subject: Re: [Flexradio] SSB Tx Audio Punch Ian, I do have the same problem. The audio punch is gone after SVN1836. It looks like a change has been made to the voice processing routine to avoid a potential PA overdrive but that diminished the SSB average power significantly. If you are using the Tortoise you can always roll back to a version number you'd want to. I did exactly that, have rolled back to SVN1836 and stopped updating since then. This problem has been reported on the reflector a while back but I guess nothing has been done to correct it. I wish we could follow the new SVN updates but it looks like if we want to keep the SSB punch we will have to stick to SVN1836 for the time being. Thanks, Alex (OP8Y) -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Ian Scoble Sent: Friday, January 04, 2008 9:57 PM To: flexradio@flex-radio.biz Subject: [Flexradio] SSB Tx Audio Punch Please can anyone else confirm whether they are having audio punch problems on SSB, the problem seems to have occurred since the SVN upgrade on or around 1840. I did put a bug up on the board but this seems to have been deleted other people I know are having the same problem and I was wondering how wide spread it is. Thanks Ian G0CTO ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] SSB Tx Audio Punch
I am still using a very old SVN with my HPSDR, so have not experienced these recent problems. Personally, I am in favour of using the envelope tracker, which I believe is implemented in COMP, rather than CPDR. The envelope tracker seems to be the closest we get to analogue RF clipping, which is still my favourite. I do not like companding, as it is very difficult to obtain enough compression without introducing harmonic distortion, which detracts from intelligibility on DX contacts. I am toying with the idea of not using any compression with PowerSDR, and using an outboard RF clipper, either analogue RF, or possibly the software version by Alex, VE3NEA. Unfortunately, my own coding skills are not adequate, or I would be writing a DSP version of an RF clipper myself, and offering it to the project. Does anyone with better skills than mine feel like trying that? 73, Greg, ZL3IX John P Basilotto W5GI wrote: > I'm really perplexed by these posts. I am using SVN 1875. ALC was added > ahead of the audio chain to prevent distortion and overdrive; however, a DX > button was added to increase the CPDR range. A 15-25% increase in audio > processing is possible giving the FlexRadio incredible talk power. Try it, > I think you'll be impressed. The CPDR slider controls the DX processing > level. > 73 > John P. Basilotto > W5GI > Chief Operating Officer > Marketing and Sales > Office 512-535-5266 > Fax512-233-5143 > www.flex-radio.com > > -Original Message- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On Behalf Of ON9CDY > Sent: Saturday, January 05, 2008 5:24 AM > To: 'Ian Scoble'; flexradio@flex-radio.biz > Subject: Re: [Flexradio] SSB Tx Audio Punch > > Ian, > > I do have the same problem. The audio punch is gone after SVN1836. It looks > like a change has been made to the voice processing routine to avoid a > potential PA overdrive but that diminished the SSB average power > significantly. If you are using the Tortoise you can always roll back to a > version number you'd want to. I did exactly that, have rolled back to > SVN1836 and stopped updating since then. This problem has been reported on > the reflector a while back but I guess nothing has been done to correct it. > I wish we could follow the new SVN updates but it looks like if we want to > keep the SSB punch we will have to stick to SVN1836 for the time being. > > Thanks, Alex (OP8Y) > > -Original Message- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On Behalf Of Ian Scoble > Sent: Friday, January 04, 2008 9:57 PM > To: flexradio@flex-radio.biz > Subject: [Flexradio] SSB Tx Audio Punch > > > > > > Please can anyone else confirm whether they are having audio punch problems > on SSB, the problem seems to have occurred since the SVN upgrade on or > around 1840. I did put a bug up on the board but this seems to have been > deleted other people I know are having the same problem and I was wondering > how wide spread it is. > > > > Thanks Ian G0CTO > > > > ___ > FlexRadio Systems Mailing List > FlexRadio@flex-radio.biz > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kb.flex-radio.com/ Homepage: > http://www.flex-radio.com/ > > > ___ > FlexRadio Systems Mailing List > FlexRadio@flex-radio.biz > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kb.flex-radio.com/ Homepage: > http://www.flex-radio.com/ > > > > ___ > FlexRadio Systems Mailing List > FlexRadio@flex-radio.biz > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kb.flex-radio.com/ Homepage: > http://www.flex-radio.com/ > > > ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] SSB Tx Audio Punch
I too have the "Audio Punch" problem. I tried to roll back to 1836 and ran into a lot of error messages. For now, I have settled for the official download 10.1.3 which fixed the audio problem. FYI only Doug, VA3CR www.va3cr.net -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of ON9CDY Sent: January-05-08 6:24 AM To: 'Ian Scoble'; flexradio@flex-radio.biz Subject: Re: [Flexradio] SSB Tx Audio Punch Ian, I do have the same problem. The audio punch is gone after SVN1836. It looks like a change has been made to the voice processing routine to avoid a potential PA overdrive but that diminished the SSB average power significantly. If you are using the Tortoise you can always roll back to a version number you'd want to. I did exactly that, have rolled back to SVN1836 and stopped updating since then. This problem has been reported on the reflector a while back but I guess nothing has been done to correct it. I wish we could follow the new SVN updates but it looks like if we want to keep the SSB punch we will have to stick to SVN1836 for the time being. Thanks, Alex (OP8Y) -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Ian Scoble Sent: Friday, January 04, 2008 9:57 PM To: flexradio@flex-radio.biz Subject: [Flexradio] SSB Tx Audio Punch Please can anyone else confirm whether they are having audio punch problems on SSB, the problem seems to have occurred since the SVN upgrade on or around 1840. I did put a bug up on the board but this seems to have been deleted other people I know are having the same problem and I was wondering how wide spread it is. Thanks Ian G0CTO ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] SSB Tx Audio Punch
I'm really perplexed by these posts. I am using SVN 1875. ALC was added ahead of the audio chain to prevent distortion and overdrive; however, a DX button was added to increase the CPDR range. A 15-25% increase in audio processing is possible giving the FlexRadio incredible talk power. Try it, I think you'll be impressed. The CPDR slider controls the DX processing level. 73 John P. Basilotto W5GI Chief Operating Officer Marketing and Sales Office 512-535-5266 Fax512-233-5143 www.flex-radio.com -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of ON9CDY Sent: Saturday, January 05, 2008 5:24 AM To: 'Ian Scoble'; flexradio@flex-radio.biz Subject: Re: [Flexradio] SSB Tx Audio Punch Ian, I do have the same problem. The audio punch is gone after SVN1836. It looks like a change has been made to the voice processing routine to avoid a potential PA overdrive but that diminished the SSB average power significantly. If you are using the Tortoise you can always roll back to a version number you'd want to. I did exactly that, have rolled back to SVN1836 and stopped updating since then. This problem has been reported on the reflector a while back but I guess nothing has been done to correct it. I wish we could follow the new SVN updates but it looks like if we want to keep the SSB punch we will have to stick to SVN1836 for the time being. Thanks, Alex (OP8Y) -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Ian Scoble Sent: Friday, January 04, 2008 9:57 PM To: flexradio@flex-radio.biz Subject: [Flexradio] SSB Tx Audio Punch Please can anyone else confirm whether they are having audio punch problems on SSB, the problem seems to have occurred since the SVN upgrade on or around 1840. I did put a bug up on the board but this seems to have been deleted other people I know are having the same problem and I was wondering how wide spread it is. Thanks Ian G0CTO ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] SSB Tx Audio Punch
Ian, I do have the same problem. The audio punch is gone after SVN1836. It looks like a change has been made to the voice processing routine to avoid a potential PA overdrive but that diminished the SSB average power significantly. If you are using the Tortoise you can always roll back to a version number you'd want to. I did exactly that, have rolled back to SVN1836 and stopped updating since then. This problem has been reported on the reflector a while back but I guess nothing has been done to correct it. I wish we could follow the new SVN updates but it looks like if we want to keep the SSB punch we will have to stick to SVN1836 for the time being. Thanks, Alex (OP8Y) -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Ian Scoble Sent: Friday, January 04, 2008 9:57 PM To: flexradio@flex-radio.biz Subject: [Flexradio] SSB Tx Audio Punch Please can anyone else confirm whether they are having audio punch problems on SSB, the problem seems to have occurred since the SVN upgrade on or around 1840. I did put a bug up on the board but this seems to have been deleted other people I know are having the same problem and I was wondering how wide spread it is. Thanks Ian G0CTO ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] SSB Tx Audio Punch
10 band 1k max 500 approx 7 250 approx 3 preamp approx 1 Like the old Starkist commercial "Sorry Charlie, we don't want audio with good taste, we want audio that tastes LOUD!" On 1/4/2008 5:11:43 PM, Ted ([EMAIL PROTECTED]) wrote: > "And a narrow but sharp hump." > what frequency?, 3 band or 10?, approximately how much? > > > > > - Original Message > From: FireBrick <[EMAIL PROTECTED]> > To: Ian Scoble <[EMAIL PROTECTED]>; flexradio@flex-radio.biz > Sent: Friday, January 4, 2008 2:15:00 PM > Subject: Re: [Flexradio] SSB Tx Audio Punch > > > Not I. > SVN1875 > using a Heil ProSet with 'DX' element > Mic Gain 3 > Compander 1 > Compression 1 > With the Equalizer Preamp barely above Zero > And a narrow but sharp hump. > > I do very little SSB but have busted a couple of tough pileups the past > few > days much to my amazement. > > I strongly suggest you try another mic. > > BTW, I also have a MFK DVK inline and that provides almost identical > sound. > > > ----- Original Message - > From: "Ian Scoble" <[EMAIL PROTECTED]> > To: > Sent: Friday, January 04, 2008 2:56 PM > Subject: [Flexradio] SSB Tx Audio Punch > > > > > > > > > > > > Please can anyone else confirm whether they are having audio punch > > problems > > on SSB, the problem seems to have occurred since the SVN upgrade ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] SSB Tx Audio Punch
"And a narrow but sharp hump." what frequency?, 3 band or 10?, approximately how much? - Original Message From: FireBrick <[EMAIL PROTECTED]> To: Ian Scoble <[EMAIL PROTECTED]>; flexradio@flex-radio.biz Sent: Friday, January 4, 2008 2:15:00 PM Subject: Re: [Flexradio] SSB Tx Audio Punch Not I. SVN1875 using a Heil ProSet with 'DX' element Mic Gain 3 Compander 1 Compression 1 With the Equalizer Preamp barely above Zero And a narrow but sharp hump. I do very little SSB but have busted a couple of tough pileups the past few days much to my amazement. I strongly suggest you try another mic. BTW, I also have a MFK DVK inline and that provides almost identical sound. - Original Message - From: "Ian Scoble" <[EMAIL PROTECTED]> To: Sent: Friday, January 04, 2008 2:56 PM Subject: [Flexradio] SSB Tx Audio Punch > > > > > Please can anyone else confirm whether they are having audio punch > problems > on SSB, the problem seems to have occurred since the SVN upgrade on or > around 1840. I did put a bug up on the board but this seems to have been > deleted other people I know are having the same problem and I was > wondering > how wide spread it is. > > > > Thanks Ian G0CTO > > > > ___ > FlexRadio Systems Mailing List > FlexRadio@flex-radio.biz > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kb.flex-radio.com/ Homepage: > http://www.flex-radio.com/ > ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/ Looking for last minute shopping deals? Find them fast with Yahoo! Search. http://tools.search.yahoo.com/newsearch/category.php?category=shopping ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] SSB Tx Audio Punch
Not I. SVN1875 using a Heil ProSet with 'DX' element Mic Gain 3 Compander 1 Compression 1 With the Equalizer Preamp barely above Zero And a narrow but sharp hump. I do very little SSB but have busted a couple of tough pileups the past few days much to my amazement. I strongly suggest you try another mic. BTW, I also have a MFK DVK inline and that provides almost identical sound. - Original Message - From: "Ian Scoble" <[EMAIL PROTECTED]> To: Sent: Friday, January 04, 2008 2:56 PM Subject: [Flexradio] SSB Tx Audio Punch > > > > > Please can anyone else confirm whether they are having audio punch > problems > on SSB, the problem seems to have occurred since the SVN upgrade on or > around 1840. I did put a bug up on the board but this seems to have been > deleted other people I know are having the same problem and I was > wondering > how wide spread it is. > > > > Thanks Ian G0CTO > > > > ___ > FlexRadio Systems Mailing List > FlexRadio@flex-radio.biz > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kb.flex-radio.com/ Homepage: > http://www.flex-radio.com/ > ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] SSB Tx Audio Punch
Hello Ian, Bug reports are not deleted, however their status will change over time. When searching for bug reports, try checking the "ANY status" checkbox on the bug report list page, and then click the 'Search' button. By doing that, all bug reports will be displayed. You can then click the "Submitted By" column in the table of data, and it will sort based upon that column, after which you can scroll through the data until you find any that were submitted by you. Your bug report was marked as 'CLOSED' because it was a duplicate of a previously entered bug report on the same topic. See your bug report at: http://support.flex-radio.com/ReviewBug.aspx?id=1502&it=B and the prior one related to the same issue at: http://support.flex-radio.com/ReviewBug.aspx?id=1499&it=B 73, Dale WA8SRA Ian Scoble wrote: > > > > > Please can anyone else confirm whether they are having audio punch problems > on SSB, the problem seems to have occurred since the SVN upgrade on or > around 1840. I did put a bug up on the board but this seems to have been > deleted other people I know are having the same problem and I was wondering > how wide spread it is. > > > > Thanks Ian G0CTO > > > > ___ > FlexRadio Systems Mailing List > FlexRadio@flex-radio.biz > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kb.flex-radio.com/ Homepage: > http://www.flex-radio.com/ > > > > ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] SSB Tx Audio Punch
Ian, check your MIC level-you may have to increase your mixer or MIC levels. You should achieve between -5 and 0dB on the MIC meter, regardless of Drive level. For additional punch try using the CPDR. The latest SVN software has an exceptionally good feature the "DX" control which will increase your processing level by at least 10 dB for exceptional "punch" John P. Basilotto W5GI Chief Operating Officer Marketing and Sales Office 512-535-5266 Fax512-233-5143 www.flex-radio.com -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Ian Scoble Sent: Friday, January 04, 2008 2:57 PM To: flexradio@flex-radio.biz Subject: [Flexradio] SSB Tx Audio Punch Please can anyone else confirm whether they are having audio punch problems on SSB, the problem seems to have occurred since the SVN upgrade on or around 1840. I did put a bug up on the board but this seems to have been deleted other people I know are having the same problem and I was wondering how wide spread it is. Thanks Ian G0CTO ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
[Flexradio] SSB Tx Audio Punch
Please can anyone else confirm whether they are having audio punch problems on SSB, the problem seems to have occurred since the SVN upgrade on or around 1840. I did put a bug up on the board but this seems to have been deleted other people I know are having the same problem and I was wondering how wide spread it is. Thanks Ian G0CTO ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/