Re: Need LOM dogs and split nut
Good evening, You can call Legacy and ask for Cindy in the Manual parts dept. I just ordered one today in fact. $26.00 I think Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Mon, Jan 28, 2019 at 9:52 PM Love to turn in Oregon wrote: > I need a couple of split nuts for my 1200. Mine is just about worn thru. > What would be the best way to get them? > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Need LOM dogs and split nut
I need a couple of split nuts for my 1200. Mine is just about worn thru. What would be the best way to get them? -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Need LOM dogs and split nut
hey tim!...I have not sold any split nuts...no one has asked...if anyone is interested, contact me here, but take measurements and perhaps a photo so it is clear that the split nuts I made are the same as what you have...joe b. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Need LOM dogs and split nut
If that does not work, I can supply however many dogs you would like. Did Joe B. sell all of the split nuts he made this summer? On Nov 4, 2017 5:46 PM, Joe Gassen <wordsmit...@gmail.com> wrote: > > Thanks Tim, Ill call back Monday! > > > On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: > > > > Call Legacy back and ask for Cindy. She is in charge of the parts for the > > manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot > > <ru...@yknotwood.com > wrote: > > > > > > BUY EXTRA !! :>) > > > > > > > > > > > > From: legacy-orna...@googlegroups.com [mailto: > > legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe > > G > > > Sent: Friday, November 03, 2017 6:51 PM > > > To: legacy-orna...@googlegroups.com > > > Subject: Re: Need LOM dogs and split nut > > > > > > > > > > > > Thanks guys for the help. I called Legacy and the man that answered said > > he would have someone call me back and he thought they had the parts. > > > > > > No call yet..fingers crossed! > > > > > > > > > > > > > > > > > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE <curtg...@wowway.com > > > wrote: > > > > > > Hello again Joe > > > > > > > > > > > > do you still have the old split nut? Its just the upper half you need? > > If so I may be some help for you. I own a home made tap for the 5/8 x 4 > > acme screw. I can tap a piece of durlin (SP?) plastic for you, then you can > > cut it to fit... > > > > > > Please let me know if you still need help on this? > > > > > > more latter. > > > > > > > > > > > > C.A.G. > > > > > > > > > > > > _ > > > > > > From: "Joe Gassen" <words...@gmail.com > > > > To: "Legacy Ornamental Mills" <legacy-orna...@googlegroups.com > > > > > > Sent: Friday, November 3, 2017 12:07:33 PM > > > Subject: Need LOM dogs and split nut -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Need LOM dogs and split nut
Got mine from Grizzly http://www.grizzly.com/products/Cupped-Live-Center-for-Wood-Lathe-MT2/H3404?utm_campaign=zPage_source=grizzly.com [http://cdn0.grizzly.com/grizzly2/images/griz-ind-short-red-gold-matted.png]<http://www.grizzly.com/products/Cupped-Live-Center-for-Wood-Lathe-MT2/H3404?utm_campaign=zPage_source=grizzly.com> Cupped Live Center for Wood Lathe - MT2 | Grizzly Industrial<http://www.grizzly.com/products/Cupped-Live-Center-for-Wood-Lathe-MT2/H3404?utm_campaign=zPage_source=grizzly.com> www.grizzly.com Cupped centers provide better grip and prevent splitting. All ball bearing construction results in very little turning resistance even when loaded. From: legacy-ornamental-mills@googlegroups.com <legacy-ornamental-mills@googlegroups.com> on behalf of CURTIS GEORGE <curtgeo...@wowway.com> Sent: Sunday, November 5, 2017 6:58 PM To: legacy-ornamental-mills@googlegroups.com Subject: Re: Need LOM dogs and split nut Lathe Live Center [Lathe Live Center]<https://nam02.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.shopsmith.com%2Fitempics%2Fljpg%2F505c%2F505602l.jpg=02%7C01%7Cmaxmd%40hotmail.com%7C1903e92b61eb4d254adc08d524b17078%7C84df9e7fe9f640afb435%7C1%7C0%7C636455266865257286=QujsncW25oxqRYPZ7QWrvDa7Tk4dRm0Dc%2BsOfSmzmKo%3D=0> Lathe Live Center Lathe Live Center provides for smooth, friction-free turning without messy lubricants Premier-quality Lathe Live Center features precision ball bearing construction for friction-free tip rotation without the need for beeswax or similar lubricants. As a result, your workpiece will turn more smoothly and quietly without the fear of unsightly burning, which, under certain circumstances, can allow your non-bearing Cup Center to loosen its grip on your stock and effect the accuracy of your cuts. Its #2 Morse taper shaft slips easily into your MARK V’s Lathe Tailstock. IMPORTANT: This Live Center is required when using Shopsmith’s Lathe Duplicator (555638). 505602 Lathe Live Center ... $41.99 (Item may be on back-order or is made upon ordering You Might Also Be Interested In: Lathe Drive Center ... $29.99<https://nam02.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.shopsmith.com%2Fownersite%2Fitemfind.htm%3Fitem%3D505715=02%7C01%7Cmaxmd%40hotmail.com%7C1903e92b61eb4d254adc08d524b17078%7C84df9e7fe9f640afb435%7C1%7C0%7C636455266865257286=SSB%2F%2Bj3PZYMv4BMw1lFGrk73%2BjcN8Kuiv9g%2BpxVElNw%3D=0> Product Reviews Currently no reviews - you can be the first to review this item [Create your own review]<https://nam02.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.shopsmith.com%2Fownersite%2Freview%2Freviewform.php%3Fitem%3D505602=02%7C01%7Cmaxmd%40hotmail.com%7C1903e92b61eb4d254adc08d524b17078%7C84df9e7fe9f640afb435%7C1%7C0%7C636455266865257286=O5KnALkI4EKxiaXvvSOQrk8TvjzWc1n%2Fv1T%2Bysg4wFA%3D=0> Order on the Web or by Phone, if you prefer -- 1-937-890-5197. Call before 4:30 PM Eastern Time From: "CURTIS GEORGE" <curtgeo...@wowway.com> To: legacy-ornamental-mills@googlegroups.com Sent: Sunday, November 5, 2017 5:12:06 PM Subject: Re: Need LOM dogs and split nut Hello guys. the face-plate idea is OK. but for the money the indexing hubs are the best tool in the arsenal of tools that Legacy ever made. Hopefully Cindy can come through for you? If not there are others out there that can make them... the Hubs are Simple, Efficient,& Practical... (ESP. or in other woods its KISS. (Keep,It Simple, Stupid.) for the price those hubs are a GREAT DEAL! C.A.G. From: "Joe G" <wordsmit...@gmail.com> To: legacy-ornamental-mills@googlegroups.com Sent: Sunday, November 5, 2017 3:46:56 PM Subject: Re: Need LOM dogs and split nut Faceplate great idea but i'll need 4 for the many steps I do.. On Sun, Nov 5, 2017 at 8:29 AM, Russ Veinot <ru...@yknotwood.com<mailto:ru...@yknotwood.com>> wrote: Excellent Suggestion !!?!! From: legacy-ornamental-mills@googlegroups.com<mailto:legacy-ornamental-mills@googlegroups.com> [mailto:legacy-ornamental-mills@googlegroups.com<mailto:legacy-ornamental-mills@googlegroups.com>] On Behalf Of Michael Kratky Sent: Sunday, November 05, 2017 8:18 AM To: legacy-ornamental-mills@googlegroups.com<mailto:legacy-ornamental-mills@googlegroups.com> Subject: RE: Need LOM dogs and split nut There’s always a lathe faceplate: [https://www.pennstateind.com/mm5/graphics/0001/CF3J_70x70.jpg] From: legacy-ornamental-mills@googlegroups.com<mailto:legacy-ornamental-mills@googlegroups.com> [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G Sent: Saturday, November 04, 2017 10:12 PM To: legacy-ornamental-mills@googlegroups.com<mailto:legacy-ornamental-mills@googlegroups.com> Subject: Re: Need LOM dog
Re: Need LOM dogs and split nut
Lathe Live Center Lathe Live Center Lathe Live Center provides for smooth, friction-free turning without messy lubricants Premier-quality Lathe Live Center features precision ball bearing construction for friction-free tip rotation without the need for beeswax or similar lubricants. As a result, your workpiece will turn more smoothly and quietly without the fear of unsightly burning, which, under certain circumstances, can allow your non-bearing Cup Center to loosen its grip on your stock and effect the accuracy of your cuts. Its #2 Morse taper shaft slips easily into your MARK V’s Lathe Tailstock. IMPORTANT : This Live Center is required when using Shopsmith’s Lathe Duplicator (555638). 505602 Lathe Live Center ... $41.99 (Item may be on back-order or is made upon ordering You Might Also Be Interested In: Lathe Drive Center ... $29.99 Product Reviews Currently no reviews - you can be the first to review this item Order on the Web or by Phone, if you prefer -- 1-937-890-5197 . Call before 4:30 PM Eastern Time - Original Message - From: "CURTIS GEORGE" <curtgeo...@wowway.com> To: legacy-ornamental-mills@googlegroups.com Sent: Sunday, November 5, 2017 5:12:06 PM Subject: Re: Need LOM dogs and split nut Hello guys. the face-plate idea is OK. but for the money the indexing hubs are the best tool in the arsenal of tools that Legacy ever made. Hopefully Cindy can come through for you? If not there are others out there that can make them... the Hubs are Simple, Efficient,& Practical... (ESP. or in other woods its KISS. (Keep,It Simple, Stupid.) for the price those hubs are a GREAT DEAL! C.A.G. - Original Message - From: "Joe G" <wordsmit...@gmail.com> To: legacy-ornamental-mills@googlegroups.com Sent: Sunday, November 5, 2017 3:46:56 PM Subject: Re: Need LOM dogs and split nut Faceplate great idea but i'll need 4 for the many steps I do.. On Sun, Nov 5, 2017 at 8:29 AM, Russ Veinot < ru...@yknotwood.com > wrote: Excellent Suggestion !!?!! From: legacy-ornamental-mills@googlegroups.com [mailto: legacy-ornamental-mills@googlegroups.com ] On Behalf Of Michael Kratky Sent: Sunday, November 05, 2017 8:18 AM To: legacy-ornamental-mills@googlegroups.com Subject: RE: Need LOM dogs and split nut There’s always a lathe faceplate: From: legacy-ornamental-mills@googlegroups.com [ mailto:legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe G Sent: Saturday, November 04, 2017 10:12 PM To: legacy-ornamental-mills@googlegroups.com Subject: Re: Need LOM dogs and split nut I have the threaded headstock with looks like a #2 MT I do have 1" X 8 thread check but it only opens to 3" I think. The legs I were turning for a table are 4" and 5" Sq at top On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot < ru...@yknotwood.com > wrote: BUY EXTRA !! :>) Oh, I already said that. Does the headstock have a threaded head for adding a 4 jaw chuck? I rarely use my LOM dogs anymore since adding one to my LOM. Does it have the #1 morse taper headstock? From: legacy-ornamental-mills@googlegroups.com [mailto: legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe Gassen Sent: Saturday, November 04, 2017 7:47 PM To: Legacy Ornamental Mills Subject: Re: Need LOM dogs and split nut Thanks Tim, Ill call back Monday! On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: Call Legacy back and ask for Cindy. She is in charge of the parts for the manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot < ru...@yknotwood.com > wrote: > > BUY EXTRA !! :>) > > > > From: legacy-orna...@googlegroups.com [ > mailto:legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe G > Sent: Friday, November 03, 2017 6:51 PM > To: legacy-orna...@googlegroups.com > Subject: Re: Need LOM dogs and split nut > > > > Thanks guys for the help. I called Legacy and the man that answered said he > would have someone call me back and he thought they had the parts. > > No call yet..fingers crossed! > > > > > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE < curtg...@wowway.com > wrote: > > Hello again Joe > > > > do you still have the old split nut? Its just the upper half you need? If so > I may be some help for you. I own a home made tap for the 5/8 x 4 acme screw. > I can tap a piece of durlin (SP?) plastic for you, then you can cut it to > fit... > > Please let me know if you still need help on this? > > more latter. > > > > C.A.G. > > > > _ > > From: "Joe Gassen" < words...@gmail.com > > To: "Legacy Ornamental Mills" < legacy-orna...@googlegroups.com > > Sent: Frid
RE: Need LOM dogs and split nut
OK, to me, simple is drilling for a 1” dowel and cut it off after. No money spend. Should have enough scrap to do this without leaving the shop. With the face plate, you would only need one. Flat piece of plywood with 4 cleats to hold the leg like a “wrench on a bolt”. They slip in and out instantly and held in with tailstock. Or one piece of flat plywood with a lag bolt screwed through it and mount on faceplate. Lots of NTI (nothing to it :>) ways. From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of CURTIS GEORGE Sent: Sunday, November 05, 2017 4:12 PM To: legacy-ornamental-mills@googlegroups.com Subject: Re: Need LOM dogs and split nut Hello guys. the face-plate idea is OK. but for the money the indexing hubs are the best tool in the arsenal of tools that Legacy ever made. Hopefully Cindy can come through for you? If not there are others out there that can make them... the Hubs are Simple, Efficient,& Practical... (ESP. or in other woods its KISS. (Keep,It Simple, Stupid.) for the price those hubs are a GREAT DEAL! C.A.G. _ From: "Joe G" <wordsmit...@gmail.com> To: legacy-ornamental-mills@googlegroups.com Sent: Sunday, November 5, 2017 3:46:56 PM Subject: Re: Need LOM dogs and split nut Faceplate great idea but i'll need 4 for the many steps I do.. On Sun, Nov 5, 2017 at 8:29 AM, Russ Veinot <ru...@yknotwood.com> wrote: Excellent Suggestion !!?!! From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Michael Kratky Sent: Sunday, November 05, 2017 8:18 AM To: legacy-ornamental-mills@googlegroups.com Subject: RE: Need LOM dogs and split nut There’s always a lathe faceplate: https://www.pennstateind.com/mm5/graphics/0001/CF3J_70x70.jpg From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G Sent: Saturday, November 04, 2017 10:12 PM To: legacy-ornamental-mills@googlegroups.com Subject: Re: Need LOM dogs and split nut Inline image 1I have the threaded headstock with looks like a #2 MT I do have 1" X 8 thread check but it only opens to 3" I think. The legs I were turning for a table are 4" and 5" Sq at topInline image 2 On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot <ru...@yknotwood.com> wrote: BUY EXTRA !! :>) Oh, I already said that. Does the headstock have a threaded head for adding a 4 jaw chuck? I rarely use my LOM dogs anymore since adding one to my LOM. Does it have the #1 morse taper headstock? From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe Gassen Sent: Saturday, November 04, 2017 7:47 PM To: Legacy Ornamental Mills Subject: Re: Need LOM dogs and split nut Thanks Tim, Ill call back Monday! On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: Call Legacy back and ask for Cindy. She is in charge of the parts for the manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot <ru...@yknotwood.com> wrote: > > BUY EXTRA !! :>) > > > > From: legacy-orna...@googlegroups.com > [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G > Sent: Friday, November 03, 2017 6:51 PM > To: legacy-orna...@googlegroups.com > Subject: Re: Need LOM dogs and split nut > > > > Thanks guys for the help. I called Legacy and the man that answered said he > would have someone call me back and he thought they had the parts. > > No call yet..fingers crossed! > > > > > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE <curtg...@wowway.com> wrote: > > Hello again Joe > > > > do you still have the old split nut? Its just the upper half you need? If so > I may be some help for you. I own a home made tap for the 5/8 x 4 acme > screw. I can tap a piece of durlin (SP?) plastic for you, then you can cut it > to fit... > > Please let me know if you still need help on this? > > more latter. > > > > C.A.G. > > > > _ > > From: "Joe Gassen" <words...@gmail.com> > To: "Legacy Ornamental Mills" <legacy-orna...@googlegroups.com> > Sent: Friday, November 3, 2017 12:07:33 PM > Subject: Need LOM dogs and split nut > > > > I sent an e-mail but later found this board. > > I have an older steel rail LOM and have recently begun to use it again. > > I need at least two of the 4 prong dogs that fit the headstock mad will also > need a split nut in the future for the 5/8 acme. > > Any help will be appreciated since I see Legacy no longer supports the older > LOM s and have also taken down the old training videos. > > Thx all > >
Re: Need LOM dogs and split nut
Hello guys. the face-plate idea is OK. but for the money the indexing hubs are the best tool in the arsenal of tools that Legacy ever made. Hopefully Cindy can come through for you? If not there are others out there that can make them... the Hubs are Simple, Efficient,& Practical... (ESP. or in other woods its KISS. (Keep,It Simple, Stupid.) for the price those hubs are a GREAT DEAL! C.A.G. - Original Message - From: "Joe G" <wordsmit...@gmail.com> To: legacy-ornamental-mills@googlegroups.com Sent: Sunday, November 5, 2017 3:46:56 PM Subject: Re: Need LOM dogs and split nut Faceplate great idea but i'll need 4 for the many steps I do.. On Sun, Nov 5, 2017 at 8:29 AM, Russ Veinot < ru...@yknotwood.com > wrote: Excellent Suggestion !!?!! From: legacy-ornamental-mills@googlegroups.com [mailto: legacy-ornamental-mills@googlegroups.com ] On Behalf Of Michael Kratky Sent: Sunday, November 05, 2017 8:18 AM To: legacy-ornamental-mills@googlegroups.com Subject: RE: Need LOM dogs and split nut There’s always a lathe faceplate: From: legacy-ornamental-mills@googlegroups.com [ mailto:legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe G Sent: Saturday, November 04, 2017 10:12 PM To: legacy-ornamental-mills@googlegroups.com Subject: Re: Need LOM dogs and split nut I have the threaded headstock with looks like a #2 MT I do have 1" X 8 thread check but it only opens to 3" I think. The legs I were turning for a table are 4" and 5" Sq at top On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot < ru...@yknotwood.com > wrote: BUY EXTRA !! :>) Oh, I already said that. Does the headstock have a threaded head for adding a 4 jaw chuck? I rarely use my LOM dogs anymore since adding one to my LOM. Does it have the #1 morse taper headstock? From: legacy-ornamental-mills@googlegroups.com [mailto: legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe Gassen Sent: Saturday, November 04, 2017 7:47 PM To: Legacy Ornamental Mills Subject: Re: Need LOM dogs and split nut Thanks Tim, Ill call back Monday! On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: Call Legacy back and ask for Cindy. She is in charge of the parts for the manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot < ru...@yknotwood.com > wrote: > > BUY EXTRA !! :>) > > > > From: legacy-orna...@googlegroups.com [ > mailto:legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe G > Sent: Friday, November 03, 2017 6:51 PM > To: legacy-orna...@googlegroups.com > Subject: Re: Need LOM dogs and split nut > > > > Thanks guys for the help. I called Legacy and the man that answered said he > would have someone call me back and he thought they had the parts. > > No call yet..fingers crossed! > > > > > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE < curtg...@wowway.com > wrote: > > Hello again Joe > > > > do you still have the old split nut? Its just the upper half you need? If so > I may be some help for you. I own a home made tap for the 5/8 x 4 acme screw. > I can tap a piece of durlin (SP?) plastic for you, then you can cut it to > fit... > > Please let me know if you still need help on this? > > more latter. > > > > C.A.G. > > > > _____ > > From: "Joe Gassen" < words...@gmail.com > > To: "Legacy Ornamental Mills" < legacy-orna...@googlegroups.com > > Sent: Friday, November 3, 2017 12:07:33 PM > Subject: Need LOM dogs and split nut > > > > I sent an e-mail but later found this board. > > I have an older steel rail LOM and have recently begun to use it again. > > I need at least two of the 4 prong dogs that fit the headstock mad will also > need a split nut in the future for the 5/8 acme. > > Any help will be appreciated since I see Legacy no longer supports the older > LOM s and have also taken down the old training videos. > > Thx all > > > > Joe > > > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com . To post to this group, send email to legacy-ornamental-mills@googlegroups.com . Visit this group at https://groups.google.com/group/legacy-ornamental-mills . For more options, visit https://groups.google.com/d/optout . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-
Re: Need LOM dogs and split nut
Faceplate great idea but i'll need 4 for the many steps I do.. On Sun, Nov 5, 2017 at 8:29 AM, Russ Veinot <ru...@yknotwood.com> wrote: > Excellent Suggestion !!?!! > > > > *From:* legacy-ornamental-mills@googlegroups.com [mailto: > legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Michael Kratky > *Sent:* Sunday, November 05, 2017 8:18 AM > *To:* legacy-ornamental-mills@googlegroups.com > *Subject:* RE: Need LOM dogs and split nut > > > > There’s always a lathe faceplate: > > > > [image: https://www.pennstateind.com/mm5/graphics/0001/CF3J_70x70.jpg] > > > > > > *From:* legacy-ornamental-mills@googlegroups.com [ > mailto:legacy-ornamental-mills@googlegroups.com > <legacy-ornamental-mills@googlegroups.com>] *On Behalf Of *Joe G > *Sent:* Saturday, November 04, 2017 10:12 PM > *To:* legacy-ornamental-mills@googlegroups.com > *Subject:* Re: Need LOM dogs and split nut > > > > [image: Inline image 1]I have the threaded headstock with looks like a #2 > MT > > I do have 1" X 8 thread check but it only opens to 3" I think. The legs I > were turning for a table are 4" and 5" Sq at top[image: Inline image 2] > > > > On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot <ru...@yknotwood.com> wrote: > > BUY EXTRA !! :>) > > Oh, I already said that. Does the headstock have a threaded head for > adding a 4 jaw chuck? I rarely use my LOM dogs anymore since adding one to > my LOM. Does it have the #1 morse taper headstock? > > > > *From:* legacy-ornamental-mills@googlegroups.com [mailto: > legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Joe Gassen > *Sent:* Saturday, November 04, 2017 7:47 PM > *To:* Legacy Ornamental Mills > > > *Subject:* Re: Need LOM dogs and split nut > > > > Thanks Tim, Ill call back Monday! > > > > On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: > > Call Legacy back and ask for Cindy. She is in charge of the parts for the > manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot > <ru...@yknotwood.com> wrote: > > > > BUY EXTRA !! :>) > > > > > > > > From: legacy-orna...@googlegroups.com [mailto:legacy-ornamental- > mi...@googlegroups.com <legacy-ornamental-mills@googlegroups.com>] On > Behalf Of Joe G > > Sent: Friday, November 03, 2017 6:51 PM > > To: legacy-orna...@googlegroups.com > > Subject: Re: Need LOM dogs and split nut > > > > > > > > Thanks guys for the help. I called Legacy and the man that answered said > he would have someone call me back and he thought they had the parts. > > > > No call yet..fingers crossed! > > > > > > > > > > > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE <curtg...@wowway.com> > wrote: > > > > Hello again Joe > > > > > > > > do you still have the old split nut? Its just the upper half you need? > If so I may be some help for you. I own a home made tap for the 5/8 x 4 > acme screw. I can tap a piece of durlin (SP?) plastic for you, then you can > cut it to fit... > > > > Please let me know if you still need help on this? > > > > more latter. > > > > > > > > C.A.G. > > > > > > > > _ > > > > From: "Joe Gassen" <words...@gmail.com> > > To: "Legacy Ornamental Mills" <legacy-orna...@googlegroups.com> > > Sent: Friday, November 3, 2017 12:07:33 PM > > Subject: Need LOM dogs and split nut > > > > > > > > I sent an e-mail but later found this board. > > > > I have an older steel rail LOM and have recently begun to use it again. > > > > I need at least two of the 4 prong dogs that fit the headstock mad will > also need a split nut in the future for the 5/8 acme. > > > > Any help will be appreciated since I see Legacy no longer supports the > older LOM s and have also taken down the old training videos. > > > > Thx all > > > > > > > > Joe > > > > > > > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to legacy-ornamental-mills@ > googlegroups.com. > Visit this group at https://groups.google.com/ > group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message becau
RE: Need LOM dogs and split nut
Excellent Suggestion !!?!! From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Michael Kratky Sent: Sunday, November 05, 2017 8:18 AM To: legacy-ornamental-mills@googlegroups.com Subject: RE: Need LOM dogs and split nut There’s always a lathe faceplate: https://www.pennstateind.com/mm5/graphics/0001/CF3J_70x70.jpg From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G Sent: Saturday, November 04, 2017 10:12 PM To: legacy-ornamental-mills@googlegroups.com Subject: Re: Need LOM dogs and split nut Inline image 1I have the threaded headstock with looks like a #2 MT I do have 1" X 8 thread check but it only opens to 3" I think. The legs I were turning for a table are 4" and 5" Sq at topInline image 2 On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot <ru...@yknotwood.com> wrote: BUY EXTRA !! :>) Oh, I already said that. Does the headstock have a threaded head for adding a 4 jaw chuck? I rarely use my LOM dogs anymore since adding one to my LOM. Does it have the #1 morse taper headstock? From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe Gassen Sent: Saturday, November 04, 2017 7:47 PM To: Legacy Ornamental Mills Subject: Re: Need LOM dogs and split nut Thanks Tim, Ill call back Monday! On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: Call Legacy back and ask for Cindy. She is in charge of the parts for the manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot <ru...@yknotwood.com> wrote: > > BUY EXTRA !! :>) > > > > From: legacy-orna...@googlegroups.com > [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G > Sent: Friday, November 03, 2017 6:51 PM > To: legacy-orna...@googlegroups.com > Subject: Re: Need LOM dogs and split nut > > > > Thanks guys for the help. I called Legacy and the man that answered said he > would have someone call me back and he thought they had the parts. > > No call yet..fingers crossed! > > > > > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE <curtg...@wowway.com> wrote: > > Hello again Joe > > > > do you still have the old split nut? Its just the upper half you need? If so > I may be some help for you. I own a home made tap for the 5/8 x 4 acme > screw. I can tap a piece of durlin (SP?) plastic for you, then you can cut it > to fit... > > Please let me know if you still need help on this? > > more latter. > > > > C.A.G. > > > > _ > > From: "Joe Gassen" <words...@gmail.com> > To: "Legacy Ornamental Mills" <legacy-orna...@googlegroups.com> > Sent: Friday, November 3, 2017 12:07:33 PM > Subject: Need LOM dogs and split nut > > > > I sent an e-mail but later found this board. > > I have an older steel rail LOM and have recently begun to use it again. > > I need at least two of the 4 prong dogs that fit the headstock mad will also > need a split nut in the future for the 5/8 acme. > > Any help will be appreciated since I see Legacy no longer supports the older > LOM s and have also taken down the old training videos. > > Thx all > > > > Joe > > > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message
RE: Need LOM dogs and split nut
There’s always a lathe faceplate: https://www.pennstateind.com/mm5/graphics/0001/CF3J_70x70.jpg From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G Sent: Saturday, November 04, 2017 10:12 PM To: legacy-ornamental-mills@googlegroups.com Subject: Re: Need LOM dogs and split nut Inline image 1I have the threaded headstock with looks like a #2 MT I do have 1" X 8 thread check but it only opens to 3" I think. The legs I were turning for a table are 4" and 5" Sq at topInline image 2 On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot <ru...@yknotwood.com> wrote: BUY EXTRA !! :>) Oh, I already said that. Does the headstock have a threaded head for adding a 4 jaw chuck? I rarely use my LOM dogs anymore since adding one to my LOM. Does it have the #1 morse taper headstock? From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe Gassen Sent: Saturday, November 04, 2017 7:47 PM To: Legacy Ornamental Mills Subject: Re: Need LOM dogs and split nut Thanks Tim, Ill call back Monday! On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: Call Legacy back and ask for Cindy. She is in charge of the parts for the manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot <ru...@yknotwood.com> wrote: > > BUY EXTRA !! :>) > > > > From: legacy-orna...@googlegroups.com > [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G > Sent: Friday, November 03, 2017 6:51 PM > To: legacy-orna...@googlegroups.com > Subject: Re: Need LOM dogs and split nut > > > > Thanks guys for the help. I called Legacy and the man that answered said he > would have someone call me back and he thought they had the parts. > > No call yet..fingers crossed! > > > > > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE <curtg...@wowway.com> wrote: > > Hello again Joe > > > > do you still have the old split nut? Its just the upper half you need? If so > I may be some help for you. I own a home made tap for the 5/8 x 4 acme > screw. I can tap a piece of durlin (SP?) plastic for you, then you can cut it > to fit... > > Please let me know if you still need help on this? > > more latter. > > > > C.A.G. > > > > _ > > From: "Joe Gassen" <words...@gmail.com> > To: "Legacy Ornamental Mills" <legacy-orna...@googlegroups.com> > Sent: Friday, November 3, 2017 12:07:33 PM > Subject: Need LOM dogs and split nut > > > > I sent an e-mail but later found this board. > > I have an older steel rail LOM and have recently begun to use it again. > > I need at least two of the 4 prong dogs that fit the headstock mad will also > need a split nut in the future for the 5/8 acme. > > Any help will be appreciated since I see Legacy no longer supports the older > LOM s and have also taken down the old training videos. > > Thx all > > > > Joe > > > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Need LOM dogs and split nut
Hello Joe most of the Legacy's that I have seen have a MT-2 as well as a 1x8 thread on the head-stock/spindle. This means most of the lathe adapters you own should fit the Legacy, the MT-1 is to small for the Legacy, but you can buy MT 1-2 adapters at any machine shop supply house, they are not expensive. C.A.G. - Original Message - From: "Joe G" <wordsmit...@gmail.com> To: legacy-ornamental-mills@googlegroups.com Sent: Saturday, November 4, 2017 10:12:02 PM Subject: Re: Need LOM dogs and split nut I have the threaded headstock with looks like a #2 MT I do have 1" X 8 thread check but it only opens to 3" I think. The legs I were turning for a table are 4" and 5" Sq at top On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot < ru...@yknotwood.com > wrote: BUY EXTRA !! :>) Oh, I already said that. Does the headstock have a threaded head for adding a 4 jaw chuck? I rarely use my LOM dogs anymore since adding one to my LOM. Does it have the #1 morse taper headstock? From: legacy-ornamental-mills@googlegroups.com [mailto: legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe Gassen Sent: Saturday, November 04, 2017 7:47 PM To: Legacy Ornamental Mills Subject: Re: Need LOM dogs and split nut Thanks Tim, Ill call back Monday! On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: Call Legacy back and ask for Cindy. She is in charge of the parts for the manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot < ru...@yknotwood.com > wrote: > > BUY EXTRA !! :>) > > > > From: legacy-orna...@googlegroups.com [mailto: > legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe G > Sent: Friday, November 03, 2017 6:51 PM > To: legacy-orna...@googlegroups.com > Subject: Re: Need LOM dogs and split nut > > > > Thanks guys for the help. I called Legacy and the man that answered said he > would have someone call me back and he thought they had the parts. > > No call yet..fingers crossed! > > > > > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE < curtg...@wowway.com > wrote: > > Hello again Joe > > > > do you still have the old split nut? Its just the upper half you need? If so > I may be some help for you. I own a home made tap for the 5/8 x 4 acme screw. > I can tap a piece of durlin (SP?) plastic for you, then you can cut it to > fit... > > Please let me know if you still need help on this? > > more latter. > > > > C.A.G. > > > > _____ > > From: "Joe Gassen" < words...@gmail.com > > To: "Legacy Ornamental Mills" < legacy-orna...@googlegroups.com > > Sent: Friday, November 3, 2017 12:07:33 PM > Subject: Need LOM dogs and split nut > > > > I sent an e-mail but later found this board. > > I have an older steel rail LOM and have recently begun to use it again. > > I need at least two of the 4 prong dogs that fit the headstock mad will also > need a split nut in the future for the 5/8 acme. > > Any help will be appreciated since I see Legacy no longer supports the older > LOM s and have also taken down the old training videos. > > Thx all > > > > Joe > > > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com . To post to this group, send email to legacy-ornamental-mills@googlegroups.com . Visit this group at https://groups.google.com/group/legacy-ornamental-mills . For more options, visit https://groups.google.com/d/optout . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com . To post to this group, send email to legacy-ornamental-mills@googlegroups.com . Visit this group at https://groups.google.com/group/legacy-ornamental-mills . For more options, visit https://groups.google.com/d/optout . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com . To post to this group, send email to legacy-ornamental-mills@googlegroups.com . Visit this group at https://groups.google.com/group/legacy-ornamental-mills . For more options, visit https://groups.google.com/d/optout . -- You received this message because you are subscribed to the Google G
RE: Need LOM dogs and split nut
You are on the money Bill. The LOM uses the 1”-8TPI headstock with the #2 morse taper almost always, **apparently even yours Jon **. The #1 and #2 tapers are not interchangeable. There might be a #2 to #1 adaptor but don’t bother. The #2 is most common among most wood lathes and LOM’s. You have a 3 choices that comes to mind. 1) You can buy a larger chuck at about $200 or more 2) you can purchase the Penn State industries’ economy chuck ( <https://www.pennstateind.com/store/CUG3418CCX.html> https://www.pennstateind.com/store/CUG3418CCX.html ) for $90 . It comes with a larger flat jaw set you could adapt for your use. 3) If you already have a smaller jaw chuck (Check? :>), you can drill a 1” hole in the end of your stock and glue a 1” dowel ( or less, size doesn’t matter) in it. This can then be used to hold the headstock end of the leg in your chuck. After finishing, cut the dowel off flush. The Penn state chuck comes with a lag screw so you could even drill a proper size hole in the leg and screw the leg on to lag screw (I guess this is kinda #4 choice :>). I really like my Penn State Chuck and rarely use the LOM dogs these days. There are a couple of other solutions that would be more complicated that I could suggest if you want, but these 3 (4) are your easiest possibilities as I see it. Hope this helps Russ P.S. if you buy a new chuck, don’t buy extra :>) From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Bill Bulkeley Sent: Saturday, November 04, 2017 9:39 PM To: legacy-ornamental-mills@googlegroups.com Subject: RE: Need LOM dogs and split nut I think it really depends on the size of your machine larger machines need larger morse tapers to handle heaver operations your machine will do.the larger the morse taper the more surface area it has to drive whatever you put in it But in a medium size lathe or the legacy mill i like a number 2 morse which is as large as you can go and still have your 1inch by 8 threads for your chucks and stuff. You can always use sleeves to make a smaller morse tool fit but not the other way round Just my opinion based on years of working in the metal working industry Bill From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of MWF Sent: Sunday, 5 November 2017 12:53 PM To: legacy-ornamental-mills@googlegroups.com Subject: RE: Need LOM dogs and split nut OK guys - its been kinda "slow" on the LOM discussions lately - so here goes: I'll toss this one out for discussion: How does one determine if the headstock on their lathe (LOM or other brand) is a #1, #2, or a #3 Morse Taper? (Short of having a "known taper" piece of stock and seeing if it "fits" into your headstock.) If given a choice of which taper to have on your device (lathe?) - which will you recommend - and WHY? Thanks. Mac _ _ -Original Message- From: Russ Veinot Sent: Nov 4, 2017 9:40 PM To: legacy-ornamental-mills@googlegroups.com Subject: RE: Need LOM dogs and split nut BUY EXTRA !! :>) Oh, I already said that. Does the headstock have a threaded head for adding a 4 jaw chuck? I rarely use my LOM dogs anymore since adding one to my LOM. Does it have the #1 morse taper headstock? From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe Gassen Sent: Saturday, November 04, 2017 7:47 PM To: Legacy Ornamental Mills Subject: Re: Need LOM dogs and split nut Thanks Tim, Ill call back Monday! On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: Call Legacy back and ask for Cindy. She is in charge of the parts for the manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot <ru...@yknotwood.com > wrote: > > BUY EXTRA !! :>) > > From: legacy-orna...@googlegroups.com > [mailto:legacy-ornamental-mills@googlegroups.com ] On Behalf > Of Joe G > Sent: Friday, November 03, 2017 6:51 PM > To: legacy-orna...@googlegroups.com > Subject: Re: Need LOM dogs and split nut > > Thanks guys for the help. I called Legacy and the man that answered said he > would have someone call me back and he thought they had the parts. > > No call yet..fingers crossed! > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE <curtg...@wowway.com > > wrote: > > Hello again Joe > > do you still have the old split nut? Its just the upper half you need? If so > I may be some help for you. I own a home made tap for the 5/8 x 4 acme > screw. I can tap a piece of durlin (SP?) plastic for you, then you can cut it > to fit... > > Please let me know if you still need help on this? > > more latter. > > C.A.G. > _ > > From: "Joe Gassen&
RE: Need LOM dogs and split nut
I think it really depends on the size of your machine larger machines need larger morse tapers to handle heaver operations your machine will do.the larger the morse taper the more surface area it has to drive whatever you put in it But in a medium size lathe or the legacy mill i like a number 2 morse which is as large as you can go and still have your 1inch by 8 threads for your chucks and stuff. You can always use sleeves to make a smaller morse tool fit but not the other way round Just my opinion based on years of working in the metal working industry Bill From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of MWF Sent: Sunday, 5 November 2017 12:53 PM To: legacy-ornamental-mills@googlegroups.com Subject: RE: Need LOM dogs and split nut OK guys - its been kinda "slow" on the LOM discussions lately - so here goes: I'll toss this one out for discussion: How does one determine if the headstock on their lathe (LOM or other brand) is a #1, #2, or a #3 Morse Taper? (Short of having a "known taper" piece of stock and seeing if it "fits" into your headstock.) If given a choice of which taper to have on your device (lathe?) - which will you recommend - and WHY? Thanks. Mac _ _ -Original Message- From: Russ Veinot Sent: Nov 4, 2017 9:40 PM To: legacy-ornamental-mills@googlegroups.com Subject: RE: Need LOM dogs and split nut BUY EXTRA !! :>) Oh, I already said that. Does the headstock have a threaded head for adding a 4 jaw chuck? I rarely use my LOM dogs anymore since adding one to my LOM. Does it have the #1 morse taper headstock? From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe Gassen Sent: Saturday, November 04, 2017 7:47 PM To: Legacy Ornamental Mills Subject: Re: Need LOM dogs and split nut Thanks Tim, Ill call back Monday! On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: Call Legacy back and ask for Cindy. She is in charge of the parts for the manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot <ru...@yknotwood.com > wrote: > > BUY EXTRA !! :>) > > From: legacy-orna...@googlegroups.com > [mailto:legacy-ornamental-mills@googlegroups.com ] On Behalf > Of Joe G > Sent: Friday, November 03, 2017 6:51 PM > To: legacy-orna...@googlegroups.com > Subject: Re: Need LOM dogs and split nut > > Thanks guys for the help. I called Legacy and the man that answered said he > would have someone call me back and he thought they had the parts. > > No call yet..fingers crossed! > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE <curtg...@wowway.com > > wrote: > > Hello again Joe > > do you still have the old split nut? Its just the upper half you need? If so > I may be some help for you. I own a home made tap for the 5/8 x 4 acme > screw. I can tap a piece of durlin (SP?) plastic for you, then you can cut it > to fit... > > Please let me know if you still need help on this? > > more latter. > > C.A.G. > _ > > From: "Joe Gassen" <words...@gmail.com > > To: "Legacy Ornamental Mills" <legacy-orna...@googlegroups.com > > > Sent: Friday, November 3, 2017 12:07:33 PM > Subject: Need LOM dogs and split nut > > I sent an e-mail but later found this board. > > I have an older steel rail LOM and have recently begun to use it again. > > I need at least two of the 4 prong dogs that fit the headstock mad will also > need a split nut in the future for the 5/8 acme. > > Any help will be appreciated since I see Legacy no longer supports the older > LOM s and have also taken down the old training videos. > > Thx all > > Joe <http://www.avg.com/email-signature?utm_medium=email_source=link_campaign=sig-email_content=emailclient> Virus-free. <http://www.avg.com/email-signature?utm_medium=email_source=link_campaign=sig-email_content=emailclient> www.avg.com -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Need LOM dogs and split nut
I was playing with a design with the spiral but decided the spiral was too fancy for a farm table. Also the "beads" below the spiral were too big so I went with the plain taper. Sure wish I could score the old Legacy "design kit" I have trouble visualizing what a cutter looks like with partial or full cutting depth. On Sat, Nov 4, 2017 at 9:12 PM, Joe G <wordsmit...@gmail.com> wrote: > [image: Inline image 1]I have the threaded headstock with looks like a #2 > MT > I do have 1" X 8 thread check but it only opens to 3" I think. The legs I > were turning for a table are 4" and 5" Sq at top[image: Inline image 2] > > On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot <ru...@yknotwood.com> wrote: > >> BUY EXTRA !! :>) >> >> Oh, I already said that. Does the headstock have a threaded head for >> adding a 4 jaw chuck? I rarely use my LOM dogs anymore since adding one to >> my LOM. Does it have the #1 morse taper headstock? >> >> >> >> *From:* legacy-ornamental-mills@googlegroups.com [mailto: >> legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Joe Gassen >> *Sent:* Saturday, November 04, 2017 7:47 PM >> *To:* Legacy Ornamental Mills >> >> *Subject:* Re: Need LOM dogs and split nut >> >> >> >> Thanks Tim, Ill call back Monday! >> >> >> >> On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: >> >> Call Legacy back and ask for Cindy. She is in charge of the parts for >> the manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ >> Veinot <ru...@yknotwood.com> wrote: >> > >> > BUY EXTRA !! :>) >> > >> > >> > >> > From: legacy-orna...@googlegroups.com [mailto:legacy-ornamental-mill >> s...@googlegroups.com] On Behalf Of Joe G >> > Sent: Friday, November 03, 2017 6:51 PM >> > To: legacy-orna...@googlegroups.com >> > Subject: Re: Need LOM dogs and split nut >> > >> > >> > >> > Thanks guys for the help. I called Legacy and the man that answered >> said he would have someone call me back and he thought they had the parts. >> > >> > No call yet..fingers crossed! >> > >> > >> > >> > >> > >> > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE <curtg...@wowway.com> >> wrote: >> > >> > Hello again Joe >> > >> > >> > >> > do you still have the old split nut? Its just the upper half you need? >> If so I may be some help for you. I own a home made tap for the 5/8 x 4 >> acme screw. I can tap a piece of durlin (SP?) plastic for you, then you can >> cut it to fit... >> > >> > Please let me know if you still need help on this? >> > >> > more latter. >> > >> > >> > >> > C.A.G. >> > >> > >> > >> > _ >> > >> > From: "Joe Gassen" <words...@gmail.com> >> > To: "Legacy Ornamental Mills" <legacy-orna...@googlegroups.com> >> > Sent: Friday, November 3, 2017 12:07:33 PM >> > Subject: Need LOM dogs and split nut >> > >> > >> > >> > I sent an e-mail but later found this board. >> > >> > I have an older steel rail LOM and have recently begun to use it again. >> > >> > I need at least two of the 4 prong dogs that fit the headstock mad will >> also need a split nut in the future for the 5/8 acme. >> > >> > Any help will be appreciated since I see Legacy no longer supports the >> older LOM s and have also taken down the old training videos. >> > >> > Thx all >> > >> > >> > >> > Joe >> > >> > >> > >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >> To post to this group, send email to legacy-ornamental-mills@google >> groups.com. >> Visit this group at https://groups.google.com/grou >> p/legacy-ornamental-mills. >> For more options, visit https://groups.google.com/d/optout. >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >> To post to this group, send email to legacy-ornamental-mills@google >> groups.com. >> Visit this group at https://groups.google.com/grou >> p/legacy-ornamental-mills. >> For more options, visit https://groups.google.com/d/optout. >> > > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Need LOM dogs and split nut
[image: Inline image 1]I have the threaded headstock with looks like a #2 MT I do have 1" X 8 thread check but it only opens to 3" I think. The legs I were turning for a table are 4" and 5" Sq at top[image: Inline image 2] On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot <ru...@yknotwood.com> wrote: > BUY EXTRA !! :>) > > Oh, I already said that. Does the headstock have a threaded head for > adding a 4 jaw chuck? I rarely use my LOM dogs anymore since adding one to > my LOM. Does it have the #1 morse taper headstock? > > > > *From:* legacy-ornamental-mills@googlegroups.com [mailto: > legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Joe Gassen > *Sent:* Saturday, November 04, 2017 7:47 PM > *To:* Legacy Ornamental Mills > > *Subject:* Re: Need LOM dogs and split nut > > > > Thanks Tim, Ill call back Monday! > > > > On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: > > Call Legacy back and ask for Cindy. She is in charge of the parts for the > manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot > <ru...@yknotwood.com> wrote: > > > > BUY EXTRA !! :>) > > > > > > > > From: legacy-orna...@googlegroups.com [mailto:legacy-ornamental-mill > s...@googlegroups.com] On Behalf Of Joe G > > Sent: Friday, November 03, 2017 6:51 PM > > To: legacy-orna...@googlegroups.com > > Subject: Re: Need LOM dogs and split nut > > > > > > > > Thanks guys for the help. I called Legacy and the man that answered said > he would have someone call me back and he thought they had the parts. > > > > No call yet..fingers crossed! > > > > > > > > > > > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE <curtg...@wowway.com> > wrote: > > > > Hello again Joe > > > > > > > > do you still have the old split nut? Its just the upper half you need? > If so I may be some help for you. I own a home made tap for the 5/8 x 4 > acme screw. I can tap a piece of durlin (SP?) plastic for you, then you can > cut it to fit... > > > > Please let me know if you still need help on this? > > > > more latter. > > > > > > > > C.A.G. > > > > > > > > _ > > > > From: "Joe Gassen" <words...@gmail.com> > > To: "Legacy Ornamental Mills" <legacy-orna...@googlegroups.com> > > Sent: Friday, November 3, 2017 12:07:33 PM > > Subject: Need LOM dogs and split nut > > > > > > > > I sent an e-mail but later found this board. > > > > I have an older steel rail LOM and have recently begun to use it again. > > > > I need at least two of the 4 prong dogs that fit the headstock mad will > also need a split nut in the future for the 5/8 acme. > > > > Any help will be appreciated since I see Legacy no longer supports the > older LOM s and have also taken down the old training videos. > > > > Thx all > > > > > > > > Joe > > > > > > > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to legacy-ornamental-mills@google > groups.com. > Visit this group at https://groups.google.com/grou > p/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to legacy-ornamental-mills@google > groups.com. > Visit this group at https://groups.google.com/grou > p/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Need LOM dogs and split nut
Before I turn in for the night, i use what's on the machine, also same size on lathe, so apparently common. If you need to know, Google something. Better yet throw it in here!. You'll get a few rattles; https://en.wikipedia.org/wiki/Machine_taper [https://upload.wikimedia.org/wikipedia/commons/thumb/1/1d/ChuckDrillKeyedKeylessArbor.jpg/1200px-ChuckDrillKeyedKeylessArbor.jpg]<https://en.wikipedia.org/wiki/Machine_taper> Machine taper - Wikipedia<https://en.wikipedia.org/wiki/Machine_taper> en.wikipedia.org A machine taper is a system for securing cutting tools or toolholders in the spindle of a machine tool or power tool. A male member of conical form (that is, with a ... From: legacy-ornamental-mills@googlegroups.com <legacy-ornamental-mills@googlegroups.com> on behalf of MWF <mwfos...@earthlink.net> Sent: Saturday, November 4, 2017 8:52 PM To: legacy-ornamental-mills@googlegroups.com Subject: RE: Need LOM dogs and split nut OK guys - its been kinda "slow" on the LOM discussions lately - so here goes: I'll toss this one out for discussion: How does one determine if the headstock on their lathe (LOM or other brand) is a #1, #2, or a #3 Morse Taper? (Short of having a "known taper" piece of stock and seeing if it "fits" into your headstock.) If given a choice of which taper to have on your device (lathe?) - which will you recommend - and WHY? Thanks. Mac -Original Message- From: Russ Veinot Sent: Nov 4, 2017 9:40 PM To: legacy-ornamental-mills@googlegroups.com Subject: RE: Need LOM dogs and split nut BUY EXTRA !! :>) Oh, I already said that. Does the headstock have a threaded head for adding a 4 jaw chuck? I rarely use my LOM dogs anymore since adding one to my LOM. Does it have the #1 morse taper headstock? From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe Gassen Sent: Saturday, November 04, 2017 7:47 PM To: Legacy Ornamental Mills Subject: Re: Need LOM dogs and split nut Thanks Tim, Ill call back Monday! On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: Call Legacy back and ask for Cindy. She is in charge of the parts for the manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot <ru...@yknotwood.com> wrote: > > BUY EXTRA !! :>) > > From: legacy-orna...@googlegroups.com > [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G > Sent: Friday, November 03, 2017 6:51 PM > To: legacy-orna...@googlegroups.com > Subject: Re: Need LOM dogs and split nut > > Thanks guys for the help. I called Legacy and the man that answered said he > would have someone call me back and he thought they had the parts. > > No call yet..fingers crossed! > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE <curtg...@wowway.com> wrote: > > Hello again Joe > > do you still have the old split nut? Its just the upper half you need? If so > I may be some help for you. I own a home made tap for the 5/8 x 4 acme > screw. I can tap a piece of durlin (SP?) plastic for you, then you can cut it > to fit... > > Please let me know if you still need help on this? > > more latter. > > C.A.G. > _ > > From: "Joe Gassen" <words...@gmail.com> > To: "Legacy Ornamental Mills" <legacy-orna...@googlegroups.com> > Sent: Friday, November 3, 2017 12:07:33 PM > Subject: Need LOM dogs and split nut > > I sent an e-mail but later found this board. > > I have an older steel rail LOM and have recently begun to use it again. > > I need at least two of the 4 prong dogs that fit the headstock mad will also > need a split nut in the future for the 5/8 acme. > > Any help will be appreciated since I see Legacy no longer supports the older > LOM s and have also taken down the old training videos. > > Thx all > > Joe -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com<mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com>. To post to this group, send email to legacy-ornamental-mills@googlegroups.com<mailto:legacy-ornamental-mills@googlegroups.com>. Visit this group at https://groups.google.com/group/legacy-ornamental-mills<https://eur02.safelinks.protection.outlook.com/?url=https%3A%2F%2Fgroups.google.com%2Fgroup%2Flegacy-ornamental-mills=02%7C01%7Cmaxmd%40hotmail.com%7C3ff0e6689f7f46904d6708d523eff0e6%7C84df9e7fe9f640afb435%7C1%7C0%7C636454435804853338=54ZrtDrbO7GJJJHj7RxwCb1P%2Bng4OPuo9tGORFuUd5w%3D=0>. For more
RE: Need LOM dogs and split nut
BUY EXTRA !! :>) Oh, I already said that. Does the headstock have a threaded head for adding a 4 jaw chuck? I rarely use my LOM dogs anymore since adding one to my LOM. Does it have the #1 morse taper headstock? From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe Gassen Sent: Saturday, November 04, 2017 7:47 PM To: Legacy Ornamental Mills Subject: Re: Need LOM dogs and split nut Thanks Tim, Ill call back Monday! On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: Call Legacy back and ask for Cindy. She is in charge of the parts for the manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot <ru...@yknotwood.com > wrote: > > BUY EXTRA !! :>) > > > > From: legacy-orna...@googlegroups.com > [mailto:legacy-ornamental-mills@googlegroups.com ] On Behalf Of > Joe G > Sent: Friday, November 03, 2017 6:51 PM > To: legacy-orna...@googlegroups.com > Subject: Re: Need LOM dogs and split nut > > > > Thanks guys for the help. I called Legacy and the man that answered said he > would have someone call me back and he thought they had the parts. > > No call yet..fingers crossed! > > > > > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE <curtg...@wowway.com > > wrote: > > Hello again Joe > > > > do you still have the old split nut? Its just the upper half you need? If so > I may be some help for you. I own a home made tap for the 5/8 x 4 acme > screw. I can tap a piece of durlin (SP?) plastic for you, then you can cut it > to fit... > > Please let me know if you still need help on this? > > more latter. > > > > C.A.G. > > > > _ > > From: "Joe Gassen" <words...@gmail.com > > To: "Legacy Ornamental Mills" <legacy-orna...@googlegroups.com > > > Sent: Friday, November 3, 2017 12:07:33 PM > Subject: Need LOM dogs and split nut > > > > I sent an e-mail but later found this board. > > I have an older steel rail LOM and have recently begun to use it again. > > I need at least two of the 4 prong dogs that fit the headstock mad will also > need a split nut in the future for the 5/8 acme. > > Any help will be appreciated since I see Legacy no longer supports the older > LOM s and have also taken down the old training videos. > > Thx all > > > > Joe > > > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Need LOM dogs and split nut
Thanks Tim, Ill call back Monday! On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: > > Call Legacy back and ask for Cindy. She is in charge of the parts for the > manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot > <ru...@yknotwood.com > wrote: > > > > BUY EXTRA !! :>) > > > > > > > > From: legacy-orna...@googlegroups.com [mailto: > legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe > G > > Sent: Friday, November 03, 2017 6:51 PM > > To: legacy-orna...@googlegroups.com > > Subject: Re: Need LOM dogs and split nut > > > > > > > > Thanks guys for the help. I called Legacy and the man that answered said > he would have someone call me back and he thought they had the parts. > > > > No call yet..fingers crossed! > > > > > > > > > > > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE <curtg...@wowway.com > > wrote: > > > > Hello again Joe > > > > > > > > do you still have the old split nut? Its just the upper half you need? > If so I may be some help for you. I own a home made tap for the 5/8 x 4 > acme screw. I can tap a piece of durlin (SP?) plastic for you, then you can > cut it to fit... > > > > Please let me know if you still need help on this? > > > > more latter. > > > > > > > > C.A.G. > > > > > > > > _ > > > > From: "Joe Gassen" <words...@gmail.com > > > To: "Legacy Ornamental Mills" <legacy-orna...@googlegroups.com > > > > Sent: Friday, November 3, 2017 12:07:33 PM > > Subject: Need LOM dogs and split nut > > > > > > > > I sent an e-mail but later found this board. > > > > I have an older steel rail LOM and have recently begun to use it again. > > > > I need at least two of the 4 prong dogs that fit the headstock mad will > also need a split nut in the future for the 5/8 acme. > > > > Any help will be appreciated since I see Legacy no longer supports the > older LOM s and have also taken down the old training videos. > > > > Thx all > > > > > > > > Joe > > > > > > > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
RE: Need LOM dogs and split nut
Call Legacy back and ask for Cindy. She is in charge of the parts for the manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot <ru...@yknotwood.com> wrote: > > BUY EXTRA !! :>) > > > > From: legacy-ornamental-mills@googlegroups.com > [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G > Sent: Friday, November 03, 2017 6:51 PM > To: legacy-ornamental-mills@googlegroups.com > Subject: Re: Need LOM dogs and split nut > > > > Thanks guys for the help. I called Legacy and the man that answered said he > would have someone call me back and he thought they had the parts. > > No call yet..fingers crossed! > > > > > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE <curtgeo...@wowway.com> wrote: > > Hello again Joe > > > > do you still have the old split nut? Its just the upper half you need? If so > I may be some help for you. I own a home made tap for the 5/8 x 4 acme > screw. I can tap a piece of durlin (SP?) plastic for you, then you can cut it > to fit... > > Please let me know if you still need help on this? > > more latter. > > > > C.A.G. > > > > _ > > From: "Joe Gassen" <wordsmit...@gmail.com> > To: "Legacy Ornamental Mills" <legacy-ornamental-mills@googlegroups.com> > Sent: Friday, November 3, 2017 12:07:33 PM > Subject: Need LOM dogs and split nut > > > > I sent an e-mail but later found this board. > > I have an older steel rail LOM and have recently begun to use it again. > > I need at least two of the 4 prong dogs that fit the headstock mad will also > need a split nut in the future for the 5/8 acme. > > Any help will be appreciated since I see Legacy no longer supports the older > LOM s and have also taken down the old training videos. > > Thx all > > > > Joe > > > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
RE: Need LOM dogs and split nut
BUY EXTRA !! :>) From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G Sent: Friday, November 03, 2017 6:51 PM To: legacy-ornamental-mills@googlegroups.com Subject: Re: Need LOM dogs and split nut Thanks guys for the help. I called Legacy and the man that answered said he would have someone call me back and he thought they had the parts. No call yet..fingers crossed! On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE <curtgeo...@wowway.com> wrote: Hello again Joe do you still have the old split nut? Its just the upper half you need? If so I may be some help for you. I own a home made tap for the 5/8 x 4 acme screw. I can tap a piece of durlin (SP?) plastic for you, then you can cut it to fit... Please let me know if you still need help on this? more latter. C.A.G. _ From: "Joe Gassen" <wordsmit...@gmail.com> To: "Legacy Ornamental Mills" <legacy-ornamental-mills@googlegroups.com> Sent: Friday, November 3, 2017 12:07:33 PM Subject: Need LOM dogs and split nut I sent an e-mail but later found this board. I have an older steel rail LOM and have recently begun to use it again. I need at least two of the 4 prong dogs that fit the headstock mad will also need a split nut in the future for the 5/8 acme. Any help will be appreciated since I see Legacy no longer supports the older LOM s and have also taken down the old training videos. Thx all Joe 256-seven9seven too three 2 fore -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Need LOM dogs and split nut
Thanks guys for the help. I called Legacy and the man that answered said he would have someone call me back and he thought they had the parts. No call yet..fingers crossed! On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE <curtgeo...@wowway.com> wrote: > Hello again Joe > > do you still have the old split nut? Its just the upper half you need? If > so I may be some help for you. I own a home made tap for the 5/8 x 4 acme > screw. I can tap a piece of durlin (SP?) plastic for you, then you can cut > it to fit... > Please let me know if you still need help on this? > more latter. > > C.A.G. > > -- > *From: *"Joe Gassen" <wordsmit...@gmail.com> > *To: *"Legacy Ornamental Mills" <legacy-ornamental-mills@googlegroups.com> > *Sent: *Friday, November 3, 2017 12:07:33 PM > *Subject: *Need LOM dogs and split nut > > I sent an e-mail but later found this board. > I have an older steel rail LOM and have recently begun to use it again. > I need at least two of the 4 prong dogs that fit the headstock mad will > also need a split nut in the future for the 5/8 acme. > Any help will be appreciated since I see Legacy no longer supports the > older LOM s and have also taken down the old training videos. > Thx all > > Joe > > 256-seven9seven too three 2 fore > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to legacy-ornamental-mills@ > googlegroups.com. > Visit this group at https://groups.google.com/ > group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to legacy-ornamental-mills@ > googlegroups.com. > Visit this group at https://groups.google.com/ > group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Need LOM dogs and split nut
Hello again Joe do you still have the old split nut? Its just the upper half you need? If so I may be some help for you. I own a home made tap for the 5/8 x 4 acme screw. I can tap a piece of durlin (SP?) plastic for you, then you can cut it to fit... Please let me know if you still need help on this? more latter. C.A.G. - Original Message - From: "Joe Gassen" <wordsmit...@gmail.com> To: "Legacy Ornamental Mills" <legacy-ornamental-mills@googlegroups.com> Sent: Friday, November 3, 2017 12:07:33 PM Subject: Need LOM dogs and split nut I sent an e-mail but later found this board. I have an older steel rail LOM and have recently begun to use it again. I need at least two of the 4 prong dogs that fit the headstock mad will also need a split nut in the future for the 5/8 acme. Any help will be appreciated since I see Legacy no longer supports the older LOM s and have also taken down the old training videos. Thx all Joe 256-seven9seven too three 2 fore -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com . To post to this group, send email to legacy-ornamental-mills@googlegroups.com . Visit this group at https://groups.google.com/group/legacy-ornamental-mills . For more options, visit https://groups.google.com/d/optout . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Need LOM dogs and split nut
On Fri, Nov 3, 2017 at 3:07 PM Russ Veinot <ru...@yknotwood.com> wrote: > 5/8th acme was used on my 1200 with aluminum rails. They still sold the > split nut for mine (should be the same) as of a couple of months ago. Hope > this helps. > > > > *From:* legacy-ornamental-mills@googlegroups.com [mailto: > legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Joe Gassen > *Sent:* Friday, November 03, 2017 11:08 AM > *To:* Legacy Ornamental Mills > *Subject:* Need LOM dogs and split nut > > Thanks!! I’ll try them > I sent an e-mail but later found this board. > > I have an older steel rail LOM and have recently begun to use it again. > > I need at least two of the 4 prong dogs that fit the headstock mad will > also need a split nut in the future for the 5/8 acme. > > Any help will be appreciated since I see Legacy no longer supports the > older LOM s and have also taken down the old training videos. > > Thx all > > > > Joe > > > > 256-seven9seven too three 2 fore > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Need LOM dogs and split nut
I sent an e-mail but later found this board. I have an older steel rail LOM and have recently begun to use it again. I need at least two of the 4 prong dogs that fit the headstock mad will also need a split nut in the future for the 5/8 acme. Any help will be appreciated since I see Legacy no longer supports the older LOM s and have also taken down the old training videos. Thx all Joe 256-seven9seven too three 2 fore -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
