RE: CSmagnetic stirrer
I've not seen one that would run at less than 200 RPM Ode At 11:09 AM 11/30/2012 -0800, you wrote: Aggregation is also created by a standard laboratory magnetic stirrer. -- From: Ode Coyote [mailto:odecoy...@windstream.net] Sent: Friday, November 30, 2012 5:13 AM To: silver-list@eskimo.com Subject: Re: CSmagnetic stirrer It spins way too fast for making CS. High velocity particle collisions [DC and AC out gens] enhance aggromeration. DC gens imbedded semi conductive layers in the surface tension of bubbles on the electrode, creating more bubbles on that surface to collect particulates... builds up GreyBeard into the direction of the water flow, the structure getting progressively weaker till the current is strong enough to break it apart and wash chunks into the water Solutions: Use a very small spinner Go to pulse width motor control to keep the starting and low speed torque. Use a gear motor. Just barely moving the water works best. For 7 years Fred Sprague [Smart Silver Jr polarity switching AC generators] had a problem he just couldn't figure out with excessive amounts of large flakes and chunks forming while using a fast stirrer till we traded setups and he used the 30 RPM gear motor stirrer with his gen. Even his pulse width controlled stirrer was too fast. He apologized to me for copying it. Ode At 11:13 AM 11/29/2012 -1000, you wrote: Here's a project for the do-it-yourself craftsmen. Haven't built it, just passing on. Smitty http://tinyurl.com/blu6f73http://tinyurl.com/blu6f73
RE: CSmagnetic stirrer
i have one, a color squid european model with a speed control knob that gets pretty slow... haven't timed it _ From: Ode Coyote [mailto:odecoy...@windstream.net] Sent: Saturday, December 01, 2012 5:36 AM To: silver-list@eskimo.com Subject: RE: CSmagnetic stirrer I've not seen one that would run at less than 200 RPM Ode At 11:09 AM 11/30/2012 -0800, you wrote: Aggregation is also created by a standard laboratory magnetic stirrer.
Re: CSmagnetic stirrer
The Ika squids are advertised at RPM speeds at 0-2500 with 50 RPM increments on the dial which would mean the low speed of these models should be around 50 RPM. doug - Original Message - From: bob Larson To: silver-list@eskimo.com Sent: Saturday, December 01, 2012 1:55 PM Subject: RE: CSmagnetic stirrer i have one, a color squid european model with a speed control knob that gets pretty slow... haven't timed it
Re: CSmagnetic stirrer
It spins way too fast for making CS. High velocity particle collisions [DC and AC out gens] enhance aggromeration. DC gens imbedded semi conductive layers in the surface tension of bubbles on the electrode, creating more bubbles on that surface to collect particulates... builds up GreyBeard into the direction of the water flow, the structure getting progressively weaker till the current is strong enough to break it apart and wash chunks into the water Solutions: Use a very small spinner Go to pulse width motor control to keep the starting and low speed torque. Use a gear motor. Just barely moving the water works best. For 7 years Fred Sprague [Smart Silver Jr polarity switching AC generators] had a problem he just couldn't figure out with excessive amounts of large flakes and chunks forming while using a fast stirrer till we traded setups and he used the 30 RPM gear motor stirrer with his gen. Even his pulse width controlled stirrer was too fast. He apologized to me for copying it. Ode At 11:13 AM 11/29/2012 -1000, you wrote: Here's a project for the do-it-yourself craftsmen. Haven't built it, just passing on. Smitty http://tinyurl.com/blu6f73http://tinyurl.com/blu6f73
Re: CSmagnetic stirrer
Ode Coyote wrote: It spins way too fast for making CS. Solutions: Use a very small spinner Go to pulse width motor control to keep the starting and low speed torque. Use a gear motor. Just barely moving the water works best. Or best of all, just buy a mag stirrer base from you, Ode. LOL. sol -- The Silver List is a moderated forum for discussing Colloidal Silver. Rules and Instructions: http://www.silverlist.org Unsubscribe: mailto:silver-list-requ...@eskimo.com?subject=unsubscribe Archives: http://www.mail-archive.com/silver-list@eskimo.com/maillist.html Off-Topic discussions: mailto:silver-off-topic-l...@eskimo.com List Owner: Mike Devour mailto:mdev...@eskimo.com
RE: CSmagnetic stirrer
Aggregation is also created by a standard laboratory magnetic stirrer. _ From: Ode Coyote [mailto:odecoy...@windstream.net] Sent: Friday, November 30, 2012 5:13 AM To: silver-list@eskimo.com Subject: Re: CSmagnetic stirrer It spins way too fast for making CS. High velocity particle collisions [DC and AC out gens] enhance aggromeration. DC gens imbedded semi conductive layers in the surface tension of bubbles on the electrode, creating more bubbles on that surface to collect particulates... builds up GreyBeard into the direction of the water flow, the structure getting progressively weaker till the current is strong enough to break it apart and wash chunks into the water Solutions: Use a very small spinner Go to pulse width motor control to keep the starting and low speed torque. Use a gear motor. Just barely moving the water works best. For 7 years Fred Sprague [Smart Silver Jr polarity switching AC generators] had a problem he just couldn't figure out with excessive amounts of large flakes and chunks forming while using a fast stirrer till we traded setups and he used the 30 RPM gear motor stirrer with his gen. Even his pulse width controlled stirrer was too fast. He apologized to me for copying it. Ode At 11:13 AM 11/29/2012 -1000, you wrote: Here's a project for the do-it-yourself craftsmen. Haven't built it, just passing on. Smitty http://tinyurl.com/blu6f73
RE: CSmagnetic stirrer
Dunno about getting one from the main man, but you can't buy one from his sidekick here without buying the generator that goes with it, I tried years ago g. N. Date: Fri, 30 Nov 2012 08:55:52 -0700 From: sol...@sweetwaterhsa.com To: silver-list@eskimo.com Subject: Re: CSmagnetic stirrer Ode Coyote wrote: It spins way too fast for making CS. Solutions: Use a very small spinner Go to pulse width motor control to keep the starting and low speed torque. Use a gear motor. Just barely moving the water works best. Or best of all, just buy a mag stirrer base from you, Ode. LOL. sol -- The Silver List is a moderated forum for discussing Colloidal Silver. Rules and Instructions: http://www.silverlist.org Unsubscribe: mailto:silver-list-requ...@eskimo.com?subject=unsubscribe Archives: http://www.mail-archive.com/silver-list@eskimo.com/maillist.html Off-Topic discussions: mailto:silver-off-topic-l...@eskimo.com List Owner: Mike Devour mailto:mdev...@eskimo.com
RE: CSmagnetic stirrer
You won't have that problem with the ones I spoke of, the vortex created in the water is proportionate to the voltage used, but it works perfectly. Won't eliminate that buildup on electrodes, nothing will as far as I'm concerned, but nothing ends up in the water if one pays attention to the process as one would with any other production equipment, excluding the auto polarity switching units of course cos I know nothing about those. N. Date: Fri, 30 Nov 2012 08:12:38 -0500 To: silver-list@eskimo.com From: odecoy...@windstream.net Subject: Re: CSmagnetic stirrer It spins way too fast for making CS. High velocity particle collisions [DC and AC out gens] enhance aggromeration. DC gens imbedded semi conductive layers in the surface tension of bubbles on the electrode, creating more bubbles on that surface to collect particulates... builds up GreyBeard into the direction of the water flow, the structure getting progressively weaker till the current is strong enough to break it apart and wash chunks into the water Solutions: Use a very small spinner Go to pulse width motor control to keep the starting and low speed torque. Use a gear motor. Just barely moving the water works best. For 7 years Fred Sprague [Smart Silver Jr polarity switching AC generators] had a problem he just couldn't figure out with excessive amounts of large flakes and chunks forming while using a fast stirrer till we traded setups and he used the 30 RPM gear motor stirrer with his gen. Even his pulse width controlled stirrer was too fast. He apologized to me for copying it. Ode At 11:13 AM 11/29/2012 -1000, you wrote: Here's a project for the do-it-yourself craftsmen. Haven't built it, just passing on. Smitty http://tinyurl.com/blu6f73
RE: CSmagnetic stirrer
That's good you put that up Smitty, inspired me to explain how I make them supplementary to your link g. If I knew how to put a photo of mine on here I would, but I got this from ideas in the public domain, and there's pictures available as well if one searches DIY mag stirrers. I use kids jewellery boxes, they have a draw for stir bar storage as a bonus.Open lid and rip the mirror off, and everything else out of the top shelf.Cut hole in lid big enough for computer fan to be fixed underneath.Cut the plastic speaker cover from old radio or whatever and fix that on lid top covering the hole above fan.Wire an on/off switch connecting the fan, the switch and a power adaptor plug fixed to the box and that's pretty much it. Computer fans are 12vdc so if one can get a variable voltage power adaptor which can be lowered to lowest voltage setting to keep stir bar spinning you've got a magnetic stirrer. All you need is a hole saw for the lid, some soldering practice, some wire and switch etc. Dead simple to make and works a charm for me. N. Date: Thu, 29 Nov 2012 11:13:04 -1000 From: papad...@gmail.com To: silver-list@eskimo.com Subject: CSmagnetic stirrer Here's a project for the do-it-yourselfcraftsmen. Haven't built it, just passing on.Smitty http://tinyurl.com/blu6f73
Re: CSmagnetic stirrer
How important is a mag stirrer ? I make CS with Maple leaf coins and 4 - 9v batteries. I may make one using your design if you think the brew is better with the stirrer. On Thu, Nov 29, 2012 at 2:56 PM, Neville Munn one.red...@hotmail.comwrote: That's good you put that up Smitty, inspired me to explain how I make them supplementary to your link g. If I knew how to put a photo of mine on here I would, but I got this from ideas in the public domain, and there's pictures available as well if one searches DIY mag stirrers. I use kids jewellery boxes, they have a draw for stir bar storage as a bonus. Open lid and rip the mirror off, and everything else out of the top shelf. Cut hole in lid big enough for computer fan to be fixed underneath. Cut the plastic speaker cover from old radio or whatever and fix that on lid top covering the hole above fan. Wire an on/off switch connecting the fan, the switch and a power adaptor plug fixed to the box and that's pretty much it. Computer fans are 12vdc so if one can get a variable voltage power adaptor which can be lowered to lowest voltage setting to keep stir bar spinning you've got a magnetic stirrer. All you need is a hole saw for the lid, some soldering practice, some wire and switch etc. Dead simple to make and works a charm for me. N. -- Date: Thu, 29 Nov 2012 11:13:04 -1000 From: papad...@gmail.com To: silver-list@eskimo.com Subject: CSmagnetic stirrer Here's a project for the do-it-yourself craftsmen. Haven't built it, just passing on. Smitty *http://tinyurl.com/blu6f73*
RE: CSmagnetic stirrer
Whoa, don't know about being 'better' Smitty, just thought I'd make one when I first got into this EIS making, and it was copied from public domain, the jewellery box was my idea that's all, a draw to store the stir bar g. How important is it? If brewing larger volumes it keeps everything moving, and I believe helps reduce possible larger particle formation whilst brewing. Sorry, I don't pretend to know the exact science of it, just what I think and do. What I will say though is, if I brew anything over 250ml, or 300ml maximum, I most definitely use the stirrer. I normally brew just over a litre a time. With your setup you probly don't brew large volumes do you? So a stirrer may not be necessary in your situation. N. Date: Thu, 29 Nov 2012 15:04:47 -1000 Subject: Re: CSmagnetic stirrer From: papad...@gmail.com To: silver-list@eskimo.com How important is a mag stirrer ?I make CS with Maple leaf coinsand 4 - 9v batteries. I may make one using your designif you think the brew is better with the stirrer. On Thu, Nov 29, 2012 at 2:56 PM, Neville Munn one.red...@hotmail.com wrote: That's good you put that up Smitty, inspired me to explain how I make them supplementary to your link g. If I knew how to put a photo of mine on here I would, but I got this from ideas in the public domain, and there's pictures available as well if one searches DIY mag stirrers. I use kids jewellery boxes, they have a draw for stir bar storage as a bonus.Open lid and rip the mirror off, and everything else out of the top shelf.Cut hole in lid big enough for computer fan to be fixed underneath. Cut the plastic speaker cover from old radio or whatever and fix that on lid top covering the hole above fan.Wire an on/off switch connecting the fan, the switch and a power adaptor plug fixed to the box and that's pretty much it. Computer fans are 12vdc so if one can get a variable voltage power adaptor which can be lowered to lowest voltage setting to keep stir bar spinning you've got a magnetic stirrer. All you need is a hole saw for the lid, some soldering practice, some wire and switch etc. Dead simple to make and works a charm for me. N. Date: Thu, 29 Nov 2012 11:13:04 -1000 From: papad...@gmail.com To: silver-list@eskimo.com Subject: CSmagnetic stirrer Here's a project for the do-it-yourselfcraftsmen. Haven't built it, just passing on.Smitty http://tinyurl.com/blu6f73
Re: CSmagnetic stirrer
I brew a qt. using a pyrex measuring pitcher-type. Works for me. I made a CS maker for my 2 sons and one for my grandaughter's piano teacher. Also one for my brother in Indiana. I'm in Hawaii. They all swear by CS guzzle it when they feel something coming on with their bodies. Nice chatting with you. Smitty On Thu, Nov 29, 2012 at 3:23 PM, Neville Munn one.red...@hotmail.comwrote: Whoa, don't know about being 'better' Smitty, just thought I'd make one when I first got into this EIS making, and it was copied from public domain, the jewellery box was my idea that's all, a draw to store the stir bar g. How important is it? If brewing larger volumes it keeps everything moving, and I believe helps reduce possible larger particle formation whilst brewing. Sorry, I don't pretend to know the exact science of it, just what I think and do. What I will say though is, if I brew anything over 250ml, or 300ml maximum, I most definitely use the stirrer. I normally brew just over a litre a time. With your setup you probly don't brew large volumes do you? So a stirrer may not be necessary in your situation. N. -- Date: Thu, 29 Nov 2012 15:04:47 -1000 Subject: Re: CSmagnetic stirrer From: papad...@gmail.com To: silver-list@eskimo.com How important is a mag stirrer ? I make CS with Maple leaf coins and 4 - 9v batteries. I may make one using your design if you think the brew is better with the stirrer. On Thu, Nov 29, 2012 at 2:56 PM, Neville Munn one.red...@hotmail.comwrote: That's good you put that up Smitty, inspired me to explain how I make them supplementary to your link g. If I knew how to put a photo of mine on here I would, but I got this from ideas in the public domain, and there's pictures available as well if one searches DIY mag stirrers. I use kids jewellery boxes, they have a draw for stir bar storage as a bonus. Open lid and rip the mirror off, and everything else out of the top shelf. Cut hole in lid big enough for computer fan to be fixed underneath. Cut the plastic speaker cover from old radio or whatever and fix that on lid top covering the hole above fan. Wire an on/off switch connecting the fan, the switch and a power adaptor plug fixed to the box and that's pretty much it. Computer fans are 12vdc so if one can get a variable voltage power adaptor which can be lowered to lowest voltage setting to keep stir bar spinning you've got a magnetic stirrer. All you need is a hole saw for the lid, some soldering practice, some wire and switch etc. Dead simple to make and works a charm for me. N. -- Date: Thu, 29 Nov 2012 11:13:04 -1000 From: papad...@gmail.com To: silver-list@eskimo.com Subject: CSmagnetic stirrer Here's a project for the do-it-yourself craftsmen. Haven't built it, just passing on. Smitty *http://tinyurl.com/blu6f73*
Re: CSMagnetic Stirrer RPM
The water will not go faster than the stirrers RPM no matter how big the spinner is. You can slow the water velocity down using a high RPM stirrer and small spinner, but everything [tallness, diameter] becomes interdependent and it can get tricky...plus, there is a tendency to create a vortex funnel in the center while velocity stays fairly low at the edges. Ode At 11:02 AM 1/30/2009 -0500, you wrote: Ode, The size of the stirrer in comparison with the surface of the vessel, influences the amount of mass stirred and the turnover. When defining magnetic stirrer's speeds, one should also include the the size of the stirrer. for instance a 1/2 magnet creates little turnover at 100 rpm. The same rpm with a 2 stirrer may spill the liquid. Best regards Frank Ode Coyote wrote: Any speed that reduces sparklies and grey beard build up on the pressure side of the water currents on round electrodes, or eddy side where pressure turns a corner on flat ones. 10-40 RPM works well. 100 might. Ode At 04:04 PM 1/29/2009 -0600, you wrote: What is a good RPM rate or range for a CS magnetic stirrer? - Steve N No virus found in this incoming message. Checked by AVG. Version: 7.5.552 / Virus Database: 270.10.15/1923 - Release Date: 1/29/2009 -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com -- No virus found in this incoming message. Checked by AVG. Version: 7.5.552 / Virus Database: 270.10.16/1925 - Release Date: 1/30/2009 7:37 AM -- No virus found in this incoming message. Checked by AVG. Version: 7.5.552 / Virus Database: 270.10.16/1925 - Release Date: 1/30/2009 -- No virus found in this outgoing message. Checked by AVG. Version: 7.5.552 / Virus Database: 270.10.16/1926 - Release Date: 1/30/2009
Re: CSMagnetic Stirrer RPM
Any speed that reduces sparklies and grey beard build up on the pressure side of the water currents on round electrodes, or eddy side where pressure turns a corner on flat ones. 10-40 RPM works well. 100 might. Ode At 04:04 PM 1/29/2009 -0600, you wrote: What is a good RPM rate or range for a CS magnetic stirrer? - Steve N No virus found in this incoming message. Checked by AVG. Version: 7.5.552 / Virus Database: 270.10.15/1923 - Release Date: 1/29/2009 -- No virus found in this outgoing message. Checked by AVG. Version: 7.5.552 / Virus Database: 270.10.16/1925 - Release Date: 1/30/2009 -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
Re: CSMagnetic Stirrer RPM
Ode, The size of the stirrer in comparison with the surface of the vessel, influences the amount of mass stirred and the turnover. When defining magnetic stirrer's speeds, one should also include the the size of the stirrer. for instance a 1/2 magnet creates little turnover at 100 rpm. The same rpm with a 2 stirrer may spill the liquid. Best regards Frank Ode Coyote wrote: Any speed that reduces sparklies and grey beard build up on the pressure side of the water currents on round electrodes, or eddy side where pressure turns a corner on flat ones. 10-40 RPM works well. 100 might. Ode At 04:04 PM 1/29/2009 -0600, you wrote: What is a good RPM rate or range for a CS magnetic stirrer? - Steve N No virus found in this incoming message. Checked by AVG. Version: 7.5.552 / Virus Database: 270.10.15/1923 - Release Date: 1/29/2009 -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
RE: CSMagnetic Stirrer RPM
You are absolutely correct in what you say about stirrer size. I was aware of the issue but others may not be. I am just considering some DC gearhead motors at All Electronics surplus and wanted to get one that was in the ballpark range, cheaper than a fish tank filter motor and better suited than the muffin fan commonly used. I will adjust stirrer size and final motor speed as needed. Thanks for the reminder though. Steve N -Original Message- From: frankcuns-r...@comcast.net [mailto:frankcuns-r...@comcast.net] Sent: Friday, January 30, 2009 8:03 AM To: silver-list@eskimo.com Subject: Re: CSMagnetic Stirrer RPM Ode, The size of the stirrer in comparison with the surface of the vessel, influences the amount of mass stirred and the turnover. When defining magnetic stirrer's speeds, one should also include the the size of the stirrer. for instance a 1/2 magnet creates little turnover at 100 rpm. The same rpm with a 2 stirrer may spill the liquid. Best regards Frank Ode Coyote wrote: Any speed that reduces sparklies and grey beard build up on the pressure side of the water currents on round electrodes, or eddy side where pressure turns a corner on flat ones. 10-40 RPM works well. 100 might. Ode At 04:04 PM 1/29/2009 -0600, you wrote: What is a good RPM rate or range for a CS magnetic stirrer? - Steve N No virus found in this incoming message. Checked by AVG. Version: 7.5.552 / Virus Database: 270.10.15/1923 - Release Date: 1/29/2009 -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
RE: CSMagnetic Stirrer RPM
Thanks, Ode. - Steve N -Original Message- From: Ode Coyote [mailto:odecoy...@windstream.net] Sent: Friday, January 30, 2009 7:20 AM To: silver-list@eskimo.com Subject: Re: CSMagnetic Stirrer RPM Any speed that reduces sparklies and grey beard build up on the pressure side of the water currents on round electrodes, or eddy side where pressure turns a corner on flat ones. 10-40 RPM works well. 100 might. Ode At 04:04 PM 1/29/2009 -0600, you wrote: What is a good RPM rate or range for a CS magnetic stirrer? - Steve N -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
Re: CSMagnetic Stirrer RPM
If you have an old record player or turntable, you can put the jar on it, and hang the electrodes down from above. Set to 33 1/3 or 16 rpm if you can. Marshall Norton, Steve wrote: You are absolutely correct in what you say about stirrer size. I was aware of the issue but others may not be. I am just considering some DC gearhead motors at All Electronics surplus and wanted to get one that was in the ballpark range, cheaper than a fish tank filter motor and better suited than the muffin fan commonly used. I will adjust stirrer size and final motor speed as needed. Thanks for the reminder though. Steve N -Original Message- From: frankcuns-r...@comcast.net [mailto:frankcuns-r...@comcast.net] Sent: Friday, January 30, 2009 8:03 AM To: silver-list@eskimo.com Subject: Re: CSMagnetic Stirrer RPM Ode, The size of the stirrer in comparison with the surface of the vessel, influences the amount of mass stirred and the turnover. When defining magnetic stirrer's speeds, one should also include the the size of the stirrer. for instance a 1/2 magnet creates little turnover at 100 rpm. The same rpm with a 2 stirrer may spill the liquid. Best regards Frank Ode Coyote wrote: Any speed that reduces sparklies and grey beard build up on the pressure side of the water currents on round electrodes, or eddy side where pressure turns a corner on flat ones. 10-40 RPM works well. 100 might. Ode At 04:04 PM 1/29/2009 -0600, you wrote: What is a good RPM rate or range for a CS magnetic stirrer? - Steve N No virus found in this incoming message. Checked by AVG. Version: 7.5.552 / Virus Database: 270.10.15/1923 - Release Date: 1/29/2009 -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
Re: CSMagnetic Stirrer RPM
Hi Steve, I've had good luck with ~30 to 40 rpm in a pint wide-mouth jar. The length of the stir-bar can make a difference too; I go for ~ three fourths of an inch, maybe up to 1-1/2. I get magnets from: http://wondermagnet.com/ [a great site with all kinds of neat homebrew stuff info] and use the skinny 1/16 X 1/2 NdBFe pushed inside polyethylene tube, and seal the ends. YMMV of course. Take care, Malcolm On Thu, 2009-01-29 at 16:04 -0600, Norton, Steve wrote: What is a good RPM rate or range for a CS magnetic stirrer? - Steve N -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
RE: CSMagnetic Stirrer RPM
Thanks for the info Malcolm. And that is an interesting site. I hadn't seen it before and will have to browse it a bit. - Steve N -Original Message- From: Malcolm [mailto:s...@asis.com] Sent: Friday, January 30, 2009 10:26 AM To: silver-list@eskimo.com Subject: Re: CSMagnetic Stirrer RPM Hi Steve, I've had good luck with ~30 to 40 rpm in a pint wide-mouth jar. The length of the stir-bar can make a difference too; I go for ~ three fourths of an inch, maybe up to 1-1/2. I get magnets from: http://wondermagnet.com/ [a great site with all kinds of neat homebrew stuff info] and use the skinny 1/16 X 1/2 NdBFe pushed inside polyethylene tube, and seal the ends. YMMV of course. Take care, Malcolm On Thu, 2009-01-29 at 16:04 -0600, Norton, Steve wrote: What is a good RPM rate or range for a CS magnetic stirrer? - Steve N -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
RE: CSMagnetic Stirrer
...the silverpuppy site has a nice one for a good price. cool looking too. i shopped stirrers w/ hotplates on ebay for quite awhile while broke and after experimenting with a hotplate decided that part isn't worth the money since it works best to start out with the water hot but let it cool during the brew process...so i opted for a mag stirrer alone, and would've bought one from silverpuppy except i lucked into a great deal on one with speed control for the same money...ebay works for me, especially when sellers don't know how to best time their auctions' end times and other little details. i do wish i had the coyotes though...single speed is actually fine. -Original Message- From: sickleave48...@aol.com [mailto:sickleave48...@aol.com] Sent: Tuesday, March 13, 2007 6:12 PM To: silver-list@eskimo.com Subject: CSMagnetic Stirrer Bought a magnetic stirrer, works great. I want to buy a second one, forgot who I bought it from. I think it was from some one on list. forgot which site it was from. Bob -- AOL now offers free email to everyone. Find out more about what's free from AOL at AOL.com.
Re: CSMagnetic Stirrer
Won't a magnetic stirrer cause the positive ions to either repel or attract toward the stirrer and maybe even plate to it? I'm assuming the stirrer itself is a plastic covered metal rod of some kind. Cheers, Steven Geigle Cedar Mill, Oregon, USA sgei...@home.com - Original Message - Hello all, It has come to my attention that Hanna Instruments is offering a magnetic stirrer that handles up to 1 litre and stirs from 100-1000 RPM. http://www.hannainst.com/products/promo/hi190_2h.htm Here is a mini-stirrer with the same basic properties: http://www.hannainst.com/products/promo/hi180.htm Special promotional prices for both types are here: http://www.hannainst.com/products/promo/usa/usaprmo.htm Regards, George Martin -- The silver-list is a moderated forum for discussion of colloidal silver. To join or quit silver-list or silver-digest send an e-mail message to: silver-list-requ...@eskimo.com -or- silver-digest-requ...@eskimo.com with the word subscribe or unsubscribe in the SUBJECT line. To post, address your message to: silver-list@eskimo.com Silver-list archive: http://escribe.com/health/thesilverlist/index.html List maintainer: Mike Devour mdev...@id.net
Re: CSMagnetic Stirrer
I've seen hundreds of these devices used in chemistry labs with no cautions I am aware of as to their use. Maybe there is a chemist on the list that can address the issue. But just for the sake of argument lets suppose that either of these two things happen. If the agglomeration occurs on the metal stirrer then that means it isn't floating around in my CS. If the ions are repelled then how does that differ from the movement caused by stirring or brownian movement? Regards, George Martin On Tue, 25 Apr 2000 04:58:15 -0700, Steve geigle wrote: =Won't a magnetic stirrer cause the positive ions to either repel or attract =toward the stirrer and maybe even plate to it? I'm assuming the stirrer =itself is a plastic covered metal rod of some kind. = =Cheers, = =Steven Geigle =Cedar Mill, Oregon, USA =sgei...@home.com =- Original Message - = = Hello all, = It has come to my attention that Hanna Instruments is = offering a magnetic stirrer that handles up to 1 litre and stirs = from 100-1000 RPM. = = http://www.hannainst.com/products/promo/hi190_2h.htm = = Here is a mini-stirrer with the same basic properties: = = http://www.hannainst.com/products/promo/hi180.htm = = Special promotional prices for both types are here: = = http://www.hannainst.com/products/promo/usa/usaprmo.htm = = Regards, = George Martin = ===END FORWARDED MESSAGE=== -- The silver-list is a moderated forum for discussion of colloidal silver. To join or quit silver-list or silver-digest send an e-mail message to: silver-list-requ...@eskimo.com -or- silver-digest-requ...@eskimo.com with the word subscribe or unsubscribe in the SUBJECT line. To post, address your message to: silver-list@eskimo.com Silver-list archive: http://escribe.com/health/thesilverlist/index.html List maintainer: Mike Devour mdev...@id.net
Re: CSMagnetic Stirrer
Everything is chemistry... If the use of a magnetic stirrer doesn't affect 'other' chemical reactions why should CS be any different? In your scenario the charged particles can only move in one direction on the flux line. If so then how is a particle more likely to have a collision with another similarly charged particle moving in the same direction at the same speed? Structuring the water by passing near a strong magnet is different from passing the water near a weak magnetic field (in the stirrer) in what way? Which one is going to have the greatest negative effect (if any)? Regards, George Martin On Tue, 25 Apr 2000 11:31:08 -0400, Marshall Dudley wrote: =Ions cannot move across magnetic lines in a straight line. They receive a =force 90 degrees to the direction of the magnetic line, and thus will spiral =around the line moving down the line. (This is what causes the Northern =Lights as well) If two particles are approaching each other normally they =have 3 degrees of freedom to avoid each other (ie. the 3 dimensions of =space). But if there is a strong magnetic field, they only have one degree =of freedom, which is directly up or down the line. Thus the probability of =a collision between two particles is greatly enhanced when there is a strong =magnetic field. It is a physics field problem, not a chemistry problem, so =it is unlikely that a chemist would know of it unless they are also trained =in physics. = =We magnetize (structure) the water in the CS that we produce. The CS runs =through a clear tube through a strong magnet for a fraction of a second. =Even so, if you look at the tube you will see that the area that runs =through the magnet is black with silver, whereas the rest of the tube is =not. = =Marshall = = = -- The silver-list is a moderated forum for discussion of colloidal silver. To join or quit silver-list or silver-digest send an e-mail message to: silver-list-requ...@eskimo.com -or- silver-digest-requ...@eskimo.com with the word subscribe or unsubscribe in the SUBJECT line. To post, address your message to: silver-list@eskimo.com Silver-list archive: http://escribe.com/health/thesilverlist/index.html List maintainer: Mike Devour mdev...@id.net