[speedtouch] Re: Speedtouch and Fedora Core 3
Hi Jyrki, I got the 330 operational by executing the following steps: 1) split firmware 2) copy 2 firmware parts to the right place 3) edit /etc/chap-secrets, /etc/pap-secrets and /etc/ppp/peers/speedtch 4) edit /etc/resolv.conf 5) connect the ST330 via USB to the PC 6) connect to the provider 7) automate the connection process during the boot process I connect to my provider using PPPoATM (so not PPPoE) and have a purple ST330. sub 1) Compile the firmware program,which you can obtain at http://linux- usb.sourceforge.net/SpeedTouch/firmware/firmware.html, using: $ gcc -o firmware firmware.c -DSTANDALONE_EXTRACTER Attention: this means that you must have the c-compiler installed! Then run the obtained program to split e.g. mgmt.o: $ ./firmware mgmt.o As a result you will have the files speedtouch-[12].bin Sub 2) # cp speedtouch-[12].bin /lib/firmware Sub 3) Add a line to both files (chap-secrets and pap-secrets) that contain your userid/pwd to connect to your provider, e.g.: "[EMAIL PROTECTED]" "*" "your_plain_password" "*" My /etc/ppp/peers/speedtch contains: # To connect to using this configuration file, do # pppd call speedtch lcp-echo-interval 10 lcp-echo-failure 3 noipdefault defaultroute user "[EMAIL PROTECTED]" noauth noaccomp nopcomp noccp novj holdoff 4 persist maxfail 25 updetach usepeerdns plugin pppoatm.so 8.48 Attention: the 8.48 numbers (vpi/vci) depend on the country you are in, verify them... It is also wise to set the access rights of the files properly (if not already done): # chown 0:0 chap-secrets pap-secrets peers/speedtch # chmod 600 chap-secrets pap-secrets peers/speedtch Sub 4) Add the (DNS) nameservers of your ISP to this file. My file contains: nameserver aa.bb.cc.d nameserver aa.bb.cc.e Attention: the aa, bb, cc, d and e should be replaced by the actual numbers of your provider. Sub 5) Make the physical connection. The firmware should be loaded automatically in the device (see LED activity on the modem). Sub 6) # /usr/sbin/pppd call speedtch The feedback on the screen should be something like: Plugin pppoatm.so loaded. PPPoATM plugin_init PPPoATM setdevname_pppoatm - SUCCESS:8.48 Using interface ppp0 Connect: ppp0 <--> 8.48 PAP authentication succeeded local IP address ff.gg.hhh.iii remote IP address jjj.kkk.lll.mm primary DNS address aa.bb.cc.d secondary DNS address aa.bb.cc.e Sub 7) To allow connection at boot I added a line to /etc/rc.d/rc.local: /usr/sbin/pppd call speedtch BTW, the /etc/ppp/options file is not needed, so I renamed it: # mv options options.orig As you will see, I did not follow the page you referred to for 100%, as I use /etc/ppp/peers/speedtch i.s.o. /etc/sysconfig/network- scripts/ifcfg-ppp0. I don't know if this might also solve your problem? I hope this helps you getting connected with FC3. Success! Aad On Tue, 2005-01-25 at 14:06 +, Jyrki Leppanen wrote: > Hi! > > I am trying to set up a new firewall/gateway to connect to the Internet > after a serious hard disk failure in my previous gateway which was set up > more than two years ago with Red Hat 8 and Speedtouch USB modem (the green > manta). As I am now using FC3 I downloaded the necessary files and followed > the instructions given in the > http://linux-usb.sourceforge.net/SpeedTouch/fedora/core-3.html pages, but > something is just not working ok. The pppd seems not be able to communicate > with the modem. The modem initialises ok with the correct sequence of leds. > What am I doing wrong? Here's an extract of the logfile: > I would be very happy of any help, > > Jyrki > > = > > Jan 25 04:24:46 enigma syslogd 1.4.1: restart. > ... > Jan 25 04:24:47 enigma kernel: Linux version 2.6.9-1.667 > ([EMAIL PROTECTED]) (gcc version 3.4.2 20041017 (Red Hat > 3.4.2-6.fc3)) #1 Tue Nov 2 14:41:25 EST 2004 > ... > Jan 25 04:24:47 enigma RFC1483/2684 bridge: Interface "nas0" created > sucessfully > Jan 25 04:24:47 enigma RFC1483/2684 bridge: Communicating over ATM 0.0.35, > encapsulation: LLC > ... > Jan 25 04:24:47 enigma RFC1483/2684 bridge: Interface configured > Jan 25 04:24:48 enigma RFC1483/2684 bridge: RFC 1483/2684 bridge daemon > started > ... > Jan 25 04:24:48 enigma pppd[2301]: Plugin rp-pppoe.so loaded. > ... > Jan 25 04:24:48 enigma pppd[2301]: RP-PPPoE plugin version 3.3 compiled > against pppd 2.4.2 > ... > Jan 25 04:24:48 enigma pppd[2301]: pppd 2.4.2 started by root, uid 0 > ... > Jan 25 04:24:49 enigma pppd[2301]: Using interface ppp0 > Jan 25 04:24:49 enigma pppd[2301]: Couldn't increase MTU to 1500 > ... > Jan 25 04:24:49 enigma pppd[2301]: Couldn't increase MRU to 1500 > Jan 25 04:24:49 enigma pppd[2301]: local IP address 10.112.112.112 > Jan 25 04:24:49 enigma pppd[2301]: remote IP address 10.112.112.113 > ... > Jan 25 04:24:51 enigma kernel: usbcore: registered new driver usbfs > Jan 25 04:24:51 enigma kernel: usbcore: registered new driver
[speedtouch] Re: modem_run problem
Hi, I have the same problem with messages during boot and shutdown (and probably also during operation): Nov 18 12:22:50 localhost kernel: usb x-y: usbfs: process (modem_run) did not claim interface 0 before use So if somebody knows how to get rid if them, please let us know... Aad On Thu, 2004-11-18 at 12:50, [EMAIL PROTECTED] wrote: > Hi everyone, > > I want to thank everybody who helped me and especially Aad: I'm writing this > mail from my Fedora system!! > Thank you a lot! > > I used linux-atm-2.4.1-1.i386.rpm (thank you Gilles Espinasse) and I have not > intalled the ppp daemon > that comes with the speedbundle, I'm using the one that comes with Fedora. > > But... there's another problem: I have my /var/log/messages continuosly filled > by this two lines: > > Nov 18 12:22:50 localhost modem_run[1720]: Error reading interrupts > Nov 18 12:22:50 localhost kernel: usb 3-1: usbfs: process 1720 (modem_run) did > not claim interface 0 before use > > They even fill the screen during the boot. > I found a dirty solution: kill -9 . > Does somebody know which is the cause of this problem and a better solution > for > this? > > Regards, > Marco Antonelli Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: speedbundle cannot find Rules.make
Hi Marco, on my system it can be found at speedbundle-1.0/linux-atm/src/lib/.libs/libatm.so so I presume it is the result of compilation of the linux-atm/src directory. It might be that the change I proposed to the speedbundle-1.0/configure breaks this in your case, whereas I used a different approach (copying atm header files to /usr/include/linux). Maybe you have to add yet another option to the line in speedbundle-1.0/configure: cd linux-atm && ./configure --prefix=/usr --includedir=/usr/src/linux-2.4.9/include --libdir=../../src/lib/.libs && cd .. && \ I doubt if it works, but you could try... Is the so-file also available on your system at the place that I mentioned? Regards, Aad On Wed, 2004-11-17 at 20:30, [EMAIL PROTECTED] wrote: > Hello Aad, > > I did everything and the compliation had got further... thank you sincerely. > But... > It blocks a little further, this is the output: > > gcc -I../../src/include -g -O2 -Wall -Wshadow -Wpointer-arith -Wwrite-strings > -Wstrict-prototypes -o .libs/aread aread.o ../../src/lib/.libs/libatm.so > -lresolv../../src/lib/.libs/libatm.so: undefined reference to `blli_in_use' > collect2: ld returned 1 exit status > make[4]: *** [aread] Error 1 > make[4]: Leaving directory `/root/Desktop/speedbundle-1.0/linux-atm/src/test' > make[3]: *** [all-recursive] Error 1 > make[3]: Leaving directory `/root/Desktop/speedbundle-1.0/linux-atm/src' > make[2]: *** [all-recursive] Error 1 > make[2]: Leaving directory `/root/Desktop/speedbundle-1.0/linux-atm' > make[1]: *** [all-recursive-am] Error 2 > make[1]: Leaving directory `/root/Desktop/speedbundle-1.0/linux-atm' > make: *** [build-stamp] Error 2 > > > I tried to search libatm.so, but it is not in my hd. > May you help me again? > > Marco Antonelli Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: speedbundle cannot find Rules.make
Hello Marco,
On Tue, 2004-11-16 at 00:39, [EMAIL PROTECTED] wrote:
> Hi Aad,
> I have understand something, but surely not everything... :(
> I eliminate those lines in the configure file and the Makefile about the
> kernel
> module and also those ones regarding the ppp daemon (I have the same version,
> 2.4.2, so I don't need a knew one).
If I understood properly some time ago, it really is needed to compile
ppp to make it atm-aware, because the version that is delivered with FC
is not. So I would not disable that part...
> As you said
> > After you disable the lines that contain "kernel_module" in these two
> > files, it will appear that compilation stops at another point (see my
> > mail of Fri, 12 Nov 2004, titled "Speedbundle under Fedora Core 3").
> I had compilation problems with the sapequal.c file.
> So I have to:
> 1a)
> > copying of the atm-header files from /usr/src/linux-2.4.9/include/linux
> > directory to /usr/include/linux.
> I have 19 atm*.h files in /usr/src/linux-2.6.9/include/linux and
> 16 atm*.h in /usr/include/linux, some files are different (like atm.h) and
> others are identic (like atm_eni.h) Is that right?
There are indeed more header files in /usr/src/linux-2.4.9/include/linux
But maybe it is better to redefine the include path for compiling the
linux-atm module (see below).
>
> or better
>
> 1b)
> > change the path to the (system) include files (Makefile
> > variable "includedir") from ${prefix}/include to
> > /usr/src/linux-2.4.9/include in the Makefile in
> > speedbundle-1.0/linux-atm, and maybe also in deeper levels of that
> > directory.
> I opened the speedbundle/linux-atm/
> I found two Makefiles: Makefile.in and Makefile.am
> In the second one is very short, and there are no "includedir" variables.
> In the second one there are these variables:
> includedir = @includedir@
> oldincludedir = /usr/include
>
> That's strange... should I use method "1a"?
I think the way to go here is to edit the line regarding linux-atm in
speedbundle-1.0/configure as follows:
cd linux-atm && ./configure --prefix=/usr
--includedir=/usr/src/linux-2.4.9/include && cd .. && \
(attention: this is one line)
So you should not have to edit any Makefile.
> 2) replacing
> default:
> }
>
> by:
>
> default:
> ;
> }
> in speedbundle-1.0/linux-atm/src/lib/sapequal.c,
> speedbundle-1.0/linux-atm/src/sigd/proto.c, and
> speedbundle-1.0/linux-atm/src/maint/enitune.c
>
> 3)Add the line "#define __user" to the file
> /usr/include/linux/atm.h before the line "#include "
>
> Am I right? Or did I forget something?
> What should I do with the atm headers?
I would edit the file /usr/src/linux-2.4.9/include/linux/atm.h (after
making a backup of the original) so that it contains the #define.
And I think that in order to get everything operational, you really need
to use the documentation link I sent you yesterday.
Success.
Aad
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: speedbundle cannot find Rules.make
Hi Marco,
after looking into your log, I see that you have the kernel module still
enabled in the configure and Makefile. If you look into the explanation
at http://www.4p8.com/eric.brasseur/speedbundle_fedora.html you can see
that this should be disabled for Fedora Core because the kernel module
for the Speedtouch is already provided (also by FC3).
After you disable the lines that contain "kernel_module" in these two
files, it will appear that compilation stops at another point (see my
mail of Fri, 12 Nov 2004, titled "Speedbundle under Fedora Core 3").
I have fixed this, but it seems to be a quick and dirty one, at least
for the copying of the atm-header files from
/usr/src/linux-2.4.9/include/linux directory to /usr/include/linux (see
reply on my mail by FrÃdÃric RUAUDEL). So maybe a better solution for
that part is to change the path to the (system) include files (Makefile
variable "includedir") from ${prefix}/include to
/usr/src/linux-2.4.9/include in the Makefile in
speedbundle-1.0/linux-atm, and maybe also in deeper levels of that
directory.
If you need more help please ask...
Kind regards,
Aad
On Mon, 2004-11-15 at 15:41, [EMAIL PROTECTED] wrote:
> Hallo everyone,
> I've got a Fedora Core 3 and a 2.6.9-1.667 kernel and I have also downloaded
> and
> installed the source of this one.
> when I try to compile the speedbundle, I got this output:
>
> cd kernel_module && make
> make[1]: Entering directory `/root/Desktop/speedbundle-1.0/kernel_module'
> make -C /lib/modules/2.6.9-1.667/build
> SUBDIRS=/root/Desktop/speedbundle-1.0/kernel_module modules
> make[2]: Entering directory `/lib/modules/2.6.9-1.667/build'
> /root/Desktop/speedbundle-1.0/kernel_module/Makefile:23:
> /lib/modules/2.6.9-1.667/build/Rules.make: No such file or directory
> make[3]: *** No rule to make target
> `/lib/modules/2.6.9-1.667/build/Rules.make'.
> Stop.
> make[2]: *** [_module_/root/Desktop/speedbundle-1.0/kernel_module] Error 2
> make[2]: Leaving directory `/lib/modules/2.6.9-1.667/build'
> make[1]: *** [speedtch.o] Error 2
> make[1]: Leaving directory `/root/Desktop/speedbundle-1.0/kernel_module'
> make: *** [build-stamp] Error 2
>
> So I tried to find Rules.make on the hard drive, but it is not present.
> So I asked Google, and I found two answers:
> 1) "You haven't got the kernel source" (but I have it)
> 2) 2.6 kernel haven't got this file anymore... Could this be possible?
>
> Please help me to find a solution,
> Marco Antonelli
>
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Speedbundle under Fedora Core 3
Hello, I have been trying to get the SpeedTouch 330 operational under Fedora Core 3. In the end I succeeded, and want to give some feedback on problems I encountered so that others can benefit from it. Some time ago I read in this list that it was needed to copy the atm header files that belong to the used kernel from /usr/src/linux-some-version/include/linux to /usr/include/linux. Therefore I downloaded the source code of the kernel that came with FC3, and installed it. It appeared to end up in /usr/src/redhat/SOURCES. I untarred linux-2.6.9.tar.bz2 such that the kernel source tree ended up in /usr/src/linux-2.6.9. Then I copied the /usr/src/linux-2.6.9/include/linux/atm*.h files to /usr/include/linux. I commented out the kernel module in configure and Makefile in the "root directory" of speedbundle-1.0, filled in some details in the ppp_scripts (as described in the documentation), and compiled the whole lot: $ make Unfortunately I got compiler errors related to 2 problems: 1) switch statements in the speedbundle sources that had an empty "default" clause 2) __user being in the way in the files /usr/include/linux/atmdev.h and /usr/include/linux/atm.h. sub 1) my compiler (gcc 3.4.2 20041017) did not like nothing after a "default" clause; it generated errors for this (not warnings). In the files speedbundle-1.0/linux-atm/src/lib/sapequal.c, speedbundle-1.0/linux-atm/src/sigd/proto.c, and speedbundle-1.0/linux-atm/src/maint/enitune.c I fixed the problem by replacing: default: } by: default: ; } sub 2) Add the line "#define __user" to the file /usr/include/linux/atm.h before the line "#include ", so that it (__user) is removed by the preprocessor. I do not oversee what is influenced by this, but it did work for me. Does anybody know the purpose of __user? After solving these problems everything compiled (here and there some warnings). Then I removed the existing ppp package with: # rpm -e --nodeps ppp and I installed the stuff: # make install I tested the modem with two commands: # /usr/sbin/modem_run -k -f /usr/lib/speedtouch/firmware.bin wait until the modem lights stay lighting up green continuously, and then: # /usr/sbin/pppd call speedtch The connection was made, so it worked. I saw that DNS did not work (when browsing using the name of the website), so I adapted /etc/resolve.conf to include the IP-addresses of the name servers of my provider. Finally I could browse the web using site names i.s.o. IP-numbers. Regarding my changes: - the first changes I made had to do with incompatibility of the speedbundle sources with the new compiler. You could add my changes to the next release of speedbundle. - the change in the kernel header file atm.h was a quick and dirty one, where I could not completely oversee what could be ruined by this. How should this be fed back to the right people? Kind regards, Aad Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: Fedora Core 2 Test 3 Issues (2.6.5 kernel)
Hi, thanks to you all I have got the Speedtouch operational with the kernel module. This incorporated the following steps: - install kernel-source rpm - apply patches of Duncan for usb - configure the kernel to include ATM, PPP Over ATM support, Speedtouch (and RFC1483/2684 Bridged Protocols, but I doubt if that is required for pppoatm) - Âmake and Âmake modules_install install for the kernel - add new kernel to grub.conf - use speedbundle-1.0, where the kernel-module part is not built/ installed. Then I see still some errors/warnings during boot, but the modem is operational (I sent this mail via FC2 using the kernel module). See the part of /var/log/messages related to the ST330: May 27 07:18:12 localhost kernel: USB Universal Host Controller Interface driver v2.2 May 27 07:18:13 localhost kernel: uhci_hcd :00:04.2: UHCI Host Controller May 27 07:18:13 localhost kernel: uhci_hcd :00:04.2: irq 9, io base d400 May 27 07:18:13 localhost kernel: uhci_hcd :00:04.2: new USB bus registered, assigned bus number 1 May 27 07:18:13 localhost kernel: hub 1-0:1.0: USB hub found May 27 07:18:13 localhost kernel: hub 1-0:1.0: 2 ports detected May 27 07:18:13 localhost kernel: uhci_hcd :00:04.3: UHCI Host Controller May 27 07:18:13 localhost kernel: uhci_hcd :00:04.3: irq 9, io base d000 May 27 07:18:13 localhost kernel: uhci_hcd :00:04.3: new USB bus registered, assigned bus number 2 May 27 07:18:13 localhost kernel: hub 2-0:1.0: USB hub found May 27 07:18:13 localhost kernel: hub 2-0:1.0: 2 ports detected May 27 07:18:13 localhost kernel: usb 1-2: new full speed USB device using address 2 May 27 07:18:13 localhost kernel: hub 1-2:1.0: USB hub found May 27 07:18:13 localhost kernel: device-mapper: 4.1.0-ioctl (2003-12-10) initialised: [EMAIL PROTECTED] May 27 07:18:13 localhost kernel: usb 1-2: control timeout on ep0in May 27 07:18:13 localhost kernel: hub 1-2:1.0: config failed, can't read hub descriptor (err -110) May 27 07:18:13 localhost kernel: usb 2-2: new full speed USB device using address 2 May 27 07:18:13 localhost kernel: hub 2-2:1.0: USB hub found May 27 07:18:13 localhost kernel: hub 2-2:1.0: 4 ports detected May 27 07:18:13 localhost kernel: usb 2-2.2: new full speed USB device using address 3 May 27 07:18:13 localhost kernel: usbcore: registered new driver speedtch May 27 07:18:13 localhost kernel: usb 2-2.2: usbfs: interface 1 claimed while 'modem_run' sets config #1 May 27 07:18:13 localhost kernel: usb 2-2.2: usbfs: interface 2 claimed while 'modem_run' sets config #1 May 27 07:18:13 localhost kernel: usb 2-2.2: bulk timeout on ep5in May 27 07:18:13 localhost kernel: usbfs: USBDEVFS_BULK failed dev 3 ep 0x85 len 512 ret -110 May 27 07:18:13 localhost kernel: usb 2-2.2: usbfs: interface 0 claimed while 'modem_run' sets config #1 May 27 07:18:13 localhost kernel: usb 2-2.2: usbfs: interface 1 claimed while 'modem_run' sets config #1 May 27 07:18:13 localhost kernel: usb 2-2.2: usbfs: interface 2 claimed while 'modem_run' sets config #1 May 27 07:18:22 localhost kernel: usbfs: process 1627 (modem_run) did not claim interface 0 before use May 27 07:18:28 localhost pppd[2533]: Plugin pppoatm.so loaded. May 27 07:18:28 localhost kernel: CSLIP: code copyright 1989 Regents of the University of California May 27 07:18:28 localhost pppd[2533]: PPPoATM plugin_init May 27 07:18:28 localhost pppd[2533]: PPPoATM setdevname - remove unwanted options May 27 07:18:28 localhost kernel: PPP generic driver version 2.4.2 May 27 07:18:28 localhost pppd[2533]: PPPoATM setdevname_pppoatm - SUCCESS:8.48 May 27 07:18:28 localhost pppd[2533]: pppd 2.4.2b3 started by root, uid 0 May 27 07:18:28 localhost pppd[2533]: Using interface ppp0 May 27 07:18:28 localhost pppd[2533]: Connect: ppp0 <--> 8.48 May 27 07:18:31 localhost pppd[2533]: PAP authentication succeeded May 27 07:18:31 localhost pppd[2533]: local IP address xx.xx.xxx.xxx May 27 07:18:31 localhost pppd[2533]: remote IP address xxx.xxx.xxx.xxx May 27 07:18:31 localhost pppd[2533]: primary DNS address xx.xx.xx.x May 27 07:18:31 localhost pppd[2533]: secondary DNS address xx.xx.xx.x Duncan, you told that most of them are due to modem_run.c and are not critical, but the ÂdonÂt look good messages as you called them are still there: May 27 07:18:13 localhost kernel: usb 1-2: control timeout on ep0in May 27 07:18:13 localhost kernel: hub 1-2:1.0: config failed, can't read hub descriptor (err -110) Everything operates however properly. Thanks all for the support! I will give feedback to Eric Brasseur who already has a webpages online with solutions for the Speedtouch 330 on FC1 (kernel space) and FC2 (user space). Regards, Aad Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: Fedora Core 2 Test 3 Issues (2.6.5 kernel)
Hi guys, thanks for all the feedback. Here is some reaction to your suggestions (it is rather long, but I thought the least I can do is to give some response to your efforts): Duncan> actually it seems to have gone fine (the firmware downloading) Does this mean that the errors/warnings can be ignored? May 23 08:07:29 localhost kernel: usb 1-2: control timeout on ep0in May 23 08:07:29 localhost kernel: hub 1-2:1.0: config failed, can't read hub descriptor (err -110) May 23 08:07:29 localhost kernel: usb 2-2.2: usbfs: interface 1 claimed while 'modem_run' sets config #1 May 23 08:07:29 localhost kernel: usb 2-2.2: usbfs: interface 2 claimed while 'modem_run' sets config #1 May 23 08:07:29 localhost kernel: usb 2-2.2: bulk timeout on ep5in May 23 08:07:29 localhost kernel: usbfs: USBDEVFS_BULK failed dev 3 ep 0x85 len 512 ret -110 May 23 08:07:29 localhost kernel: usb 2-2.2: usbfs: interface 0 claimed while 'modem_run' sets config #1 May 23 08:07:29 localhost kernel: usb 2-2.2: usbfs: interface 1 claimed while 'modem_run' sets config #1 May 23 08:07:29 localhost kernel: usb 2-2.2: usbfs: interface 2 claimed while 'modem_run' sets config #1 May 23 08:07:47 localhost kernel: usbfs: process 1608 (modem_run) did not claim interface 0 before use Is there a possibility to solve these warnings? William> I'm using Fedora Core 1, but I'll throw in my 2 cents. The William> first cent is that Fedora Core 2 final is out, so you need William> to get it. I started the thread when using test3, but in the mean time I had downloaded and installed the final version of FC2. In my mail of Sunday 23 May 2004 I was referring to problems with the "final" install. William> Next, it looks like you didn't install everything from William> speedbundle. Then again, neither did I, but you still need William> most of it. Are you sure that everything compiled and William> installed? Did you make sure to get the necessary firmware William> (It's not included with speedbundle!)? I didn't make/install pppd, linux-atm and kernel-module, because I thought that they might conflict with kernel-2.6. When configuring the kernel I selected atm, ppp over atm and the speedtouch kernel driver, so I thought that I didn't need these speedbundle parts. William> You need to move your pppd executables out of the way and William> install the pppd found in speedbundle. This will place the William> necessary pppoatm.so plugin. But read the rest of this William> first. Duncan> You need a pppoa aware pppd. The speedbundle contains one. Frédéric> Like duncan said earlier, you need a pppoa aware pppd Frédéric> daemon. In order to have this, you need to compile Frédéric> linux-atm and pppd present in the speedbundle package. OK, I will try to compile and use the version contained in speedbundle. But how are the linux-atm and pppd "packages" in speedbundle related to the stuff I activated in the kernel configuration? Are they a different way to obtain the same functionality? Frédéric> To work this around, you should (re)move all atm*.h file Frédéric> in /usr/include/linux and replace them with those present Frédéric> in the 2.6.5 kernel sources. Hmmm, good that you mention this. I did not read about this problem before. William> run ./configure from the root of the speedbundle directory. William> It will tell you what values you need to fill in the William> ppp_scripts and if you need the firmware file (you do have the William> firmware file, right?) I have the firmware file, and I made all the required changes in the ppp_scripts files. William> There is a bug in the ppp_scripts, you need to edit speedtch William> and replace the 0.00 with your VPI and VCI numbers for your William> service. Sure, I did that. William> I think that you need the kernel-source package installed, but William> I'm not certain. It's installed. William> Then try to make. If you get an error on the make, do a make William> clean, re-./configure. You will most likely fail on the William> linux-atm or ppp. If that's the case, you don't really need William> linux-atm (someone correct me if I'm wrong; if I'm right, i William> would suggest leaving it out anyways, I think this William> unnecessarily writes over stuff in your existing kernel), so William> you can make and make install on each of the directories William> individually, leaving out linux-atm. If you look at the William> top-level Makefile, you'll see how it does this (you'll want to William> copy its lines). If the make fails on ppp, check the output, William> it is most likely complaining about the kernel. In that case, William> you need to use a standard Linux kernel for the build rather William> than the Fedora Linux kernel (don't forget to move your William> original pppd executeables out of the way before installing the William> new pppd). If you don't want to mess with the standard Linux William> kernel, t
[speedtouch] Re: Fedora Core 2 Test 3 Issues (2.6.5 kernel)
> Duncan, > > I tried something else (see > http://www.4p8.com/eric.brasseur/fc2_speedtouch_usb.html), and that did > work. I have browsed the net with FC2 ;-) > I don't know if this gives you an extra clue as to why that does and the > kernel driver does not work?! > > This solution uses however the user space driver, and I still would like > to get the kernel space driver operational. So my struggle remains... > > Aad Sorry, forgot to mention that this solution worked in combination with the standard kernel that came with FC2 (no reconfiguration whatsoever). Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: Fedora Core 2 Test 3 Issues (2.6.5 kernel)
On Sun, 2004-05-23 at 10:28, Aad Rijnberg wrote: > On Sun, 2004-05-16 at 22:06, Duncan Sands wrote: > > > I have also noticed the problems with FC2 test3, and am willing to try > > > to make the changes in the final version of FC2 which will be released > > > next week. Could you then please send me the required file(s) that I > > > need to check and update? And maybe some pointers where in the source > > > files I need to look... > > > > > > When I get it to work I can post a patch file, so that every FC2 user > > > can enjoy his Speedtouch again. > > > > These should do the trick: > > > > http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED] > > http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED] > > http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED] > > http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED] > > http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED] > > http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED] > > > > Ciao, > > > > Duncan. > > Hi Duncan, > > after applying the patches and running part of speedbundle-1.0, it still > does not work :-( Do you have any suggestions for next steps that I can take? > > Regards, > Aad Duncan, I tried something else (see http://www.4p8.com/eric.brasseur/fc2_speedtouch_usb.html), and that did work. I have browsed the net with FC2 ;-) I don't know if this gives you an extra clue as to why that does and the kernel driver does not work?! This solution uses however the user space driver, and I still would like to get the kernel space driver operational. So my struggle remains... Aad Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: Fedora Core 2 Test 3 Issues (2.6.5 kernel)
On Sun, 2004-05-16 at 22:06, Duncan Sands wrote: > > I have also noticed the problems with FC2 test3, and am willing to try > > to make the changes in the final version of FC2 which will be released > > next week. Could you then please send me the required file(s) that I > > need to check and update? And maybe some pointers where in the source > > files I need to look... > > > > When I get it to work I can post a patch file, so that every FC2 user > > can enjoy his Speedtouch again. > > These should do the trick: > > http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED] > http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED] > http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED] > http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED] > http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED] > http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED] > > Ciao, > > Duncan. Hi Duncan, after applying the patches and running part of speedbundle-1.0, it still does not work :-( I have attached the details of my modifications and results: Steps taken to get the Speedtouch 330 to work: - apply the patches you mentioned to the Fedora Core 2 kernel - cd /usr/src/linux-2.6.5-1.358 - gedit include/linux/usbdevice_fs.h& - gedit drivers/usb/core/inode.c& - gedit drivers/usb/core/devio.c& - reconfigure kernel: - cp configs/kernel-2.6.5-i686.config .config - make oldconfig - make gconfig - Device drivers->Networking Support->Networking options ->Asynchronous Transfer Mode (ATM) : build as module - Then also select RFC1483/2684 Bridged Protocols: build as module and switch off "Per VC IP filter kludge" - Device Drivers->Networking Support->Network Device Support->PPP Support->PPP over ATM: build as module - Device Drivers->USB Support->Alcatel Speedtouch USB Support: build as module - save all modifications - make - make modules_install install - add new kernel to grub.conf - run (part) of speedbundle-1.0 (see also http://www.4p8.com/eric.brasseur/speedbundle_fedora.html): - I don't have a (ethernet) network interface in my computer (no default route/gateway) - Unpack speedbundle - cd speedbundle-1.0 - Do not exchange sonet.h by another one - Put firmware at right place - copy ppp_scripts/speedtch-pppoatm to ppp_scripts/speedtch and edit username and vpi.vci - edit chap-secrets and pap-secrets to include my isp-log-in information - edit Makefile and configure script, to comment out kernel_module, linux-atm and ppp - I did not remove the ppp package - make - make install - reboot to see if everything works correctly - during boot I see the leds flash and in the end both leds are green - then I look into /var/log/messages: May 23 08:07:28 localhost kernel: USB Universal Host Controller Interface driver v2.2 May 23 08:07:28 localhost kernel: uhci_hcd :00:04.2: UHCI Host Controller May 23 08:07:28 localhost kernel: uhci_hcd :00:04.2: irq 9, io base d400 May 23 08:07:28 localhost kernel: uhci_hcd :00:04.2: new USB bus registered, assigned bus number 1 May 23 08:07:28 localhost kernel: hub 1-0:1.0: USB hub found May 23 08:07:28 localhost kernel: hub 1-0:1.0: 2 ports detected May 23 08:07:28 localhost kernel: uhci_hcd :00:04.3: UHCI Host Controller May 23 08:07:28 localhost kernel: uhci_hcd :00:04.3: irq 9, io base d000 May 23 08:07:28 localhost kernel: uhci_hcd :00:04.3: new USB bus registered, assigned bus number 2 May 23 08:07:28 localhost kernel: hub 2-0:1.0: USB hub found May 23 08:07:29 localhost kernel: hub 2-0:1.0: 2 ports detected May 23 08:07:29 localhost kernel: usb 1-2: new full speed USB device using address 2 May 23 08:07:29 localhost kernel: hub 1-2:1.0: USB hub found May 23 08:07:29 localhost kernel: device-mapper: 4.1.0-ioctl (2003-12-10) initial ised: [EMAIL PROTECTED] May 23 08:07:29 localhost kernel: usb 1-2: control timeout on ep0in May 23 08:07:29 localhost kernel: hub 1-2:1.0: config failed, can't read hub descriptor (err -110) May 23 08:07:29 localhost kernel: usb 2-2: new full speed USB device using address 2 May 23 08:07:29 localhost kernel: hub 2-2:1.0: USB hub found May 23 08:07:29 localhost kernel: hub 2-2:1.0: 4 ports detected May 23 08:07:29 localhost kernel: usb 2-2.2: new full speed USB device using address 3 May 23 08:07:29 localhost kernel: usbcore: registered new driver speedtch May 23 08:07:29 localhost kernel: usb 2-2.2: usbfs: interface 1 claimed while 'modem_run' sets config #1 May 23 08:07:29 localhost kernel: usb 2-2.2: usbfs: interface 2 claimed while 'modem_run' sets config #1 May 23 08:07:29 localhost kernel: usb 2-2.2: bulk timeout on ep5in
[speedtouch] Re: Fedora Core 2 Test 3 Issues (2.6.5 kernel)
> > You better raise this issue at the [EMAIL PROTECTED] . Maybe > > somebody on that list can update you on the status of Fedora Core 2 in > > regard to this bug. > > It's a kernel problem and will be fixed in 2.6.7. Maybe the fedora people > can backport the fix (= a bunch of changes in drivers/usb/core/devio.c > by yours truly). > > Ciao, > > Duncan. Duncan, I have also noticed the problems with FC2 test3, and am willing to try to make the changes in the final version of FC2 which will be released next week. Could you then please send me the required file(s) that I need to check and update? And maybe some pointers where in the source files I need to look... When I get it to work I can post a patch file, so that every FC2 user can enjoy his Speedtouch again. Aad Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: Speedtouch 330 under Linux. Is it possible?
Hi, > Is there anybody on this list who can confirm that he uses a SpeedTouch > 330 modem under Linux to access Internet through ADSL? It could be very > usefull for a lot of people who fail in installing propely the access to > know the following : > - which type of Linux distribution and version is used. > - which driver ? : Alcatel's driver for Linux doesn't exist for this USB > ADSL Speedtouch 330 modem. If the driver used has been downloaded from > the official site (sourceforge.net) what was the version used? > - which installation procedure? I can confirm that the Alcatel 330 USB is working under Redhat Linux 8.0 (now running kernel 2.4.18-19.8.0). Steps I did to get it working: 1) I use the Papillault method (driver in user space). I followed his description on how to get it operational. At first it did not work. 2) Then I tried Steve Parker's speedtouch_conf script, still with no success 3) Finally I applied the patch to the Papillault stuff to support the "-e 1" option of modem_run. I have to mention that I could not apply the patch on the source code (probably made for a different version as the one I had). I had to make the patch by hand in the source code. And then finally it worked (after a reboot). I regret not having it written down at the time I was executing each step. It is some time ago now and I can not recall all the details. I would advise you to start of with the Papillault source files, apply the patch, and compile and install it. After that follow his description of what steps need to be taken to get it operational (a.o. the 4 files /etc/ppp/options, /etc/ppp/peers/adsl, /etc/ppp/chap-secrets or /etc/ppp/pap-secret, and finally /etc/modules.conf). If that still does not work, you could try the script of Steve Parker. I my case it only worked after the next reboot. I hope this helps you getting it to work. Regards, Aad Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]?subject=unsubscribe
