Re: [SlimDevices: Unix] piCorePlayer 7.0.0 - Public Beta
Thanks Wirrunna, I just tested my RPi3A+ with wpa_supplicant.config with pCP7.0.0b6 and it worked OK. I don't have a RPi3A to test. Greg Erskine's Profile: http://forums.slimdevices.com/member.php?userid=7403 View this thread: http://forums.slimdevices.com/showthread.php?t=113199 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] piCorePlayer 7.0.0 - Public Beta
another strong release from the Team based on picore 12.x. Best news for all pi enthusiasts. Congratulations and thanks. I clean installed and listened for a few hours to tidal, deezer and spotify and everything worked as expected (i sometimes have an issue with some tidal tracks finishing early but that is possibly an LMS issue and did not happen with 7.0.0) I noticed that The setup command greatly improved there were some changes in packages, crda went and rng-tools came pcp-update finds an update for never_remove many thanks again to all. mcduman's Profile: http://forums.slimdevices.com/member.php?userid=66702 View this thread: http://forums.slimdevices.com/showthread.php?t=113199 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] ANNOUNCE: piCorePlayer 6.0.0
There were several users trying to get the Merus Amp to work. I think I finally cracked it. _Disable_onboard_audio_ dtparm=audio=off _Disable_SPI_ Remove the spi=on from the line Code: deparam=i2c_arm=on,spi=on,i2s=on Then on the Squeezelite page, make sure you limit the sample rate to 48000. Also, make sure you do not play any music until you have turned down the Limit Threashold as described in the docs. If you try to play music with the default Alsa settings, it will likely lockup the amplifier chip requiring a reboot. Once things are set in alsa mixer, then you should save the alsa settings on the "Card Control" Page. I'll see about adding some better controls in pCP7. piCorePlayer a small player for the Raspberry Pi in RAM. Homepage: https://www.picoreplayer.org Please 'donate' (https://www.paypal.com/cgi-bin/webscr?cmd=_donations=U7JHY5WYHCNRU=GB_code=USD=PP%2dDonationsBF%3abtn_donateCC_LG%2egif%3aNonHosted) if you like the piCorePlayer paul-'s Profile: http://forums.slimdevices.com/member.php?userid=58858 View this thread: http://forums.slimdevices.com/showthread.php?t=111787 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] In ceiling set up with Pis
jeroen2 wrote: > You mean power wires to the touch screen? I bought one of 'these' > (https://thepihut.com/products/raspberry-pi-40-pin-gpio-socket-connector-to-labelled-pins-female-150mm) > and just cut off all the others. > (it also helps to not have all the unused pins exposed) Cool idea!Thx for the tip. Will definitely buy this. For my bathroom, will split controller and player. In-ceiling speakers and wires will go in a dedicated technical cupboard hooked to a pi4+AMP2. And in the bathroom, the controller will consist of a SB Touch or a Pi4+Screen. Will need to see if it I hang it or just leave it standing. When powering off from picore interface, does it bring the pi & amp into standby? Cheers! Transporter, Touch, SB3, SB2, Duet, Booms, Radios --- Ipeng & Material --- LMS 8.0.0 - 1588799628 on Pi4 4GB - Max2Play --- Qobuz didjean's Profile: http://forums.slimdevices.com/member.php?userid=2900 View this thread: http://forums.slimdevices.com/showthread.php?t=113022 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] piCorePlayer 7.0.0 - Public Beta
Well Done piCorePlayer Team, Upgraded 2 RPi 3b players with no problems. Then tried a 3a player with wpa_supplicant.conf but it wouldn't connect to WiFi. Re-flashed the SD card and booted a 3b with the card, set up wifi, put the card back into the 3a and it worked, so continued with the setup. A camel is a racehorse designed by a committee. Seen sprayed on the outside wall of the local library - Three things I hate in life : 1. Vandalism 2. Irony 3. Lists Wirrunna's Profile: http://forums.slimdevices.com/member.php?userid=3225 View this thread: http://forums.slimdevices.com/showthread.php?t=113199 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] 'Official' docker container for LMS?
mherger wrote: > >I bumped it to 1.02 for x86_64. I believe aarch still is at 0.95. > Please > update in an hour or two (or from github directly now). Thanks!! lauret's Profile: http://forums.slimdevices.com/member.php?userid=17632 View this thread: http://forums.slimdevices.com/showthread.php?t=111828 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] 'Official' docker container for LMS?
I am seeing Audio::Scan version 0.95 in the official docker image, but I am using some features from subsequent releases. Is 0.95 the latest which has been built for Perl 5.24? I bumped it to 1.02 for x86_64. I believe aarch still is at 0.95. Please update in an hour or two (or from github directly now). -- Michael ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] 'Official' docker container for LMS?
I am seeing Audio::Scan version 0.95 in the official docker image, but I am using some features from subsequent releases. Is 0.95 the latest which has been built for Perl 5.24? lauret's Profile: http://forums.slimdevices.com/member.php?userid=17632 View this thread: http://forums.slimdevices.com/showthread.php?t=111828 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] piCorePlayer 7.0.0 - Public Beta
paul- wrote: > increase the value of waitusb=xxx until your system boots reliably. I have set it to 20 and now it boots. Great! I am near the situation like before with 6.1.0. The boot is a little bit slower but that is the slow stick, the sd-card is faster. So I have to say that you did a great job! Thank you very much for this! Pi4 4GB piCorePlayer with LMS and Squeezelite for USB; Pi3B+ (7" Display, Hifiberry DAC+ Pro) piCoreplayer with Squeezlite/Jivelite for Hifiberry and Bluetooth headphone; two Airport Express carsten_h's Profile: http://forums.slimdevices.com/member.php?userid=69113 View this thread: http://forums.slimdevices.com/showthread.php?t=113199 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] piCorePlayer 7.0.0 - Public Beta
@carsten_h I have just flashed the 64 bit image onto a usb stick for a rpi3b+ using the rpi Imager Here is the boot log > [Starting piCorePlayer v7.0.0b6 startup... > Starting rngd using /dev/hwrng... Done. > Checking for boot files on sda1... > Trying to mount /dev/sda1. > ssh file found on sda1. > newpcp.cfg not found on sda1. > Setting default piCorePlayer repository... > Generating sound card drop-down list... > Loading configuration file... Done. > Loading pcp-lms-functions... Done. > Waiting for soundcard Headphones to populate. Done (1). > Waiting for network... > No network found! Done (52). > Done. > Starting Openssh server... Done. > Starting Squeezelite and/or Shairport-sync... > [ INFO ] Starting Squeezelite player: Squeezelite... > Done. > Auto set timezone settings, can be updated on tweaks page... > There was a problem reaching sites for automatic timezone, please set > manually on tweaks page. > Starting httpd web server... Done. > Starting to Advertise pcp.local... Valid IP address not found.Setting > CPU scaling governor to ondemand... Done. > Creating static footer... Done. > > Finished piCorePlayer v7.0.0b6 startup. > > To setup piCorePlayer, use the web interface via a browser: > > Press [Enter] to access console. > > In the background, ntpd is syncing time between piCorePlayer and the > internet. > A large offset between 1970 and now is normal. > /QUOTE] > > Perhaps use the checksum in the download to see if it is corrupted. > Then maybe try again > It sometimes helps to have a blank sd card loaded in the slot when using > USB for the image. > > ronnie Man in a van's Profile: http://forums.slimdevices.com/member.php?userid=43627 View this thread: http://forums.slimdevices.com/showthread.php?t=113199 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] piCorePlayer 7.0.0 - Public Beta
casten_h, The firmware and kernel access the USB stick differently. While the firmware loads the kernel and boots the system, It takes time for the kernel to find the USB drives. Edit cmdline.txt on the boot partition, and increase the value of waitusb=xxx until your system boots reliably. I've seen some USB devices take 6-8 seconds for the kernel to find them. Paul piCorePlayer a small player for the Raspberry Pi in RAM. Homepage: https://www.picoreplayer.org Please 'donate' (https://www.paypal.com/cgi-bin/webscr?cmd=_donations=U7JHY5WYHCNRU=GB_code=USD=PP%2dDonationsBF%3abtn_donateCC_LG%2egif%3aNonHosted) if you like the piCorePlayer paul-'s Profile: http://forums.slimdevices.com/member.php?userid=58858 View this thread: http://forums.slimdevices.com/showthread.php?t=113199 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] piCorePlayer 7.0.0 - Public Beta
Couple of other thoughts here. pCP has always been a headless type system, with jivelite as the only potential interface. With the revitalization of piCore OS, there has been a lot of improvements in the repos. piCore now supports the rpi vc4-kms-v3d/vc4-kms-v3d-pi4 drivers, which gives full 3d hardware acceleration. In 64 bit mode, currently only the fkms drivers work, but that still give 3d acceleration. Firefox web browser is available (epiphany also) Those wanting a lightweight full desktop interface, that should be easily done now. And provided you are not using LMS on that system, you still get "pull the plug" at anytime support. If there is interest here, we can work on some how-to's piCorePlayer a small player for the Raspberry Pi in RAM. Homepage: https://www.picoreplayer.org Please 'donate' (https://www.paypal.com/cgi-bin/webscr?cmd=_donations=U7JHY5WYHCNRU=GB_code=USD=PP%2dDonationsBF%3abtn_donateCC_LG%2egif%3aNonHosted) if you like the piCorePlayer paul-'s Profile: http://forums.slimdevices.com/member.php?userid=58858 View this thread: http://forums.slimdevices.com/showthread.php?t=113199 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] piCorePlayer 7.0.0 - Public Beta
paul- wrote: > USB will work, but it won't be stable enough for USB audio. Ok, then it is no problem here, because I use a Hifiberry for the 3B+. Only my Pi4 with LMS uses USB output. And for the in place update, it's no problem, I just wanted to know. So I think I can upgrade my 3B+ as there is not so much to configure (only Hifiberry, Jivelite and the 7" display) and and I can easily start from scratch. Pi4 4GB piCorePlayer with LMS and Squeezelite for USB; Pi3B+ (7" Display, Hifiberry DAC+ Pro) piCoreplayer with Squeezlite/Jivelite for Hifiberry and Bluetooth headphone; two Airport Express carsten_h's Profile: http://forums.slimdevices.com/member.php?userid=69113 View this thread: http://forums.slimdevices.com/showthread.php?t=113199 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] piCorePlayer 6.1.0 issues
Something is messed up on your system. You can try to run the "Update Libs" from the web interface. piCorePlayer a small player for the Raspberry Pi in RAM. Homepage: https://www.picoreplayer.org Please 'donate' (https://www.paypal.com/cgi-bin/webscr?cmd=_donations=U7JHY5WYHCNRU=GB_code=USD=PP%2dDonationsBF%3abtn_donateCC_LG%2egif%3aNonHosted) if you like the piCorePlayer paul-'s Profile: http://forums.slimdevices.com/member.php?userid=58858 View this thread: http://forums.slimdevices.com/showthread.php?t=112456 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] piCorePlayer 7.0.0 - Public Beta
carsten_h, Yes, that includes the 3B+. USB will work, but it won't be stable enough for USB audio. All RPI boards before the 4B have a pretty significantly flawed USB implementation. The work around has always been the FIQ driver. Yes, updates will follow. I have it mostly tested out, but right now, I needed to get some extra hands on the new release. I didn't want folks to upgrade in place and have unforeseen problems. I do a lot of testing, but there is only so much Greg and I can test. Paul piCorePlayer a small player for the Raspberry Pi in RAM. Homepage: https://www.picoreplayer.org Please 'donate' (https://www.paypal.com/cgi-bin/webscr?cmd=_donations=U7JHY5WYHCNRU=GB_code=USD=PP%2dDonationsBF%3abtn_donateCC_LG%2egif%3aNonHosted) if you like the piCorePlayer paul-'s Profile: http://forums.slimdevices.com/member.php?userid=58858 View this thread: http://forums.slimdevices.com/showthread.php?t=113199 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] piCorePlayer 6.1.0 issues
Thanks Ronnie It's all rather strange but before posting I rebooted several times whilst I tweaked some settings all to no avail. After your reply I thought I'd give a reboot one last try before trying the reinstall option. On this occasion it worked and I now get 'IO::Socket::SSL: 2.060' as expected. No idea why it didn't work earlier but your input is, as always, much appreciated. Regards Ashley acanning's Profile: http://forums.slimdevices.com/member.php?userid=13303 View this thread: http://forums.slimdevices.com/showthread.php?t=112456 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] piCorePlayer 6.1.0 issues
Hey Ashley this is LMS on rpi4b pCP v6.1 0 > Logitech Media Server Version: 7.9.4 - 1603273368 @ Thu Oct 22 04:21:56 > CEST 2020 > Hostname: LMS > IP: 192.168.1.119 > HTTP Port: 9000 > OS: piCore - EN - utf8 > Platform: armv8l-linux > Perl Version: 5.28.2 - > arm-linux-gnueabihf-thread-multi-64int > Audio::Scan: 1.02 > IO::Socket::SSL: 2.066 > Database Version: DBD::SQLite 1.58 (sqlite 3.22.0) > Total Players Recognized: 2 > > You could first try a LMS restart, if that is no good, then a pCP reboot, if that fails, then go to main Page in pcp and update the pcp version, this should just install over the current version (I know it's the same :D) ronnie Man in a van's Profile: http://forums.slimdevices.com/member.php?userid=43627 View this thread: http://forums.slimdevices.com/showthread.php?t=112456 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] piCorePlayer 6.1.0 issues
Morning All I seem to have an issue with the IO::Socket::SSL on my system. My Pi4 server runs LMS via pCP 6.1.0 with the following info Logitech Media Server Version: 7.9.4 - 1603273368 @ Thu Oct 22 04:21:56 CEST 2020 Hostname: piCoreLMS64 Server IP Address: 192.168.0.16 Server HTTP Port Number: 9000 Operating system: piCore - EN - utf8 Platform Architecture: armv7l-linux Perl Version: 5.28.0 - arm-linux-gnueabihf-thread-multi-64int Audio::Scan: 1.02 IO::Socket::SSL: Nothing Database Version: DBD::SQLite 1.58 (sqlite 3.22.0) Total Players Recognized: 12 I use a variety of players and have Material Skin as my default option. I dont understand the significance but I see that I have nothing against IO::Socket::SSL which doesnt look right? If I putty into my PI4 and enter the command openssl version it reports OpenSSL 1.1.0l 10 Sep 2019 but that isnt showing in LMS. This causing some problems with the BBc iPlayer plugin but I also get these errors on the plugins page Bad repository https://github.com/LMS-Community/lms...extensions.xml - Can't connect to https URL lack of IO::Socket::SSL: https://github.com/LMS-Community/lms...extensions.xml Bad repository http://raw.githubusercontent.com/mol...ter/public.xml - Can't connect to https URL lack of IO::Socket::SSL: https://raw.githubusercontent.com/mo...ter/public.xml Bad repository https://raw.githubusercontent.com/CD...ter/public.xml - Can't connect to https URL lack of IO::Socket::SSL: https://raw.githubusercontent.com/CD...ter/public.xml Bad repository https://sourceforge.net/projects/lms...64/repo_sf.xml - Can't connect to https URL lack of IO::Socket::SSL: https://sourceforge.net/projects/lms...64/repo_sf.xml Can someone please direct me as to how I install the necessary software, I havent noticed this problem before. Many thanks Ashley acanning's Profile: http://forums.slimdevices.com/member.php?userid=13303 View this thread: http://forums.slimdevices.com/showthread.php?t=112456 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
Re: [SlimDevices: Unix] piCorePlayer IR support
OK, I do have an oscilloscope, so will get it out in the next day or so. Thanks for the ideas. Perfect in every way, Modest and Misunderstood! themetman's Profile: http://forums.slimdevices.com/member.php?userid=70203 View this thread: http://forums.slimdevices.com/showthread.php?t=108410 ___ unix mailing list unix@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/unix
