Hello,
I am using dial-patern command in SRST mode, I have made it working ealrier
with dial-pattern command not sure why it's not workign now. Any help will be
higly appreciated..
here is my config...
call-manager-fallback
max-conferences 2 gain -6
transfer-system full-consult
ip
Guys,
Not to labor a point but I have set this up this morning and do not get the
positive results you get.
I have 2821 with pvdm2-32 + nm-hdv with 2 * pvdm-12.
Upgraded IOS to something which support CME conference (12.4.22T)
Run a few tests and as I say don't get quite the same
Put Site A phones in AAR Group say SiteA, location SiteA. Put Site B phones in
AAR Group say SiteB, location SiteB. Set AAR prefix, AAR CSS and route-patterns.
Lower down the b/w and AAR triggers.
jeremy co [EMAIL PROTECTED] wrote: Hi,
assuming following scenario:
Hi kapil,
If I set location on ip phones , hten when I try to call from site A ipphone
I will get out of bandwidth message.
I tried that be4.
Is there any other place to apply location ?
say u want limit your wan to site B just up to 4 calls. where this
limitation on location can be
Hi,
I have a lab today but there is a problem with page
http://proctorlabs.com/; I can open other US pages but not proctorlabs.
Nearly 15 min. passed. I tried to call the number mentioned in the book
(outside US) but all calls are sending me to the VM.
Can I re-schedule, today session?
I have the same problem
Michael Brooks
CCIE#16027 (RS)
On Sun, Nov 16, 2008 at 8:18 AM, M.Deniz KIZILCABOLUK
[EMAIL PROTECTED] wrote:
Hi,
I have a lab today but there is a problem with page
http://proctorlabs.com/; I can open other US pages but not
proctorlabs. Nearly 15 min.
I get the same thing:
M.Deniz KIZILCABOLUK wrote:
Hi,
I have a lab today but there is a problem with page
http://proctorlabs.com/; I can open other US pages but not
proctorlabs. Nearly 15 min. passed. I tried to call the number
mentioned in the book (outside US) but all calls are
Me too ... luckily I looked up my POD number last night. I can get in on
the VPN fine.
Mike Brooks wrote:
I have the same problem
Michael Brooks
CCIE#16027 (RS)
On Sun, Nov 16, 2008 at 8:18 AM, M.Deniz KIZILCABOLUK
[EMAIL PROTECTED] wrote:
Hi,
I have a lab today but there is a
I am in.I had to go through each pod in order to find it...
telnet podX.proctorlabs.com and try your username/password on each pod.
Mike Brooks
CCIE#16027 (RS)
On Sun, Nov 16, 2008 at 8:26 AM, Chris Parker [EMAIL PROTECTED] wrote:
Me too ... luckily I looked up my POD number last
Ok Thanks,
Also How can I access 6500 ? On TS there is no host .. I tried to check from
HQ-R with sh cdp/mac/arp..but telnet doesn't response..
Device ID: SAL09507GSX(VOICE-6500-1)
Entry address(es):
IP address: 192.20.200.5
Host Port Flags Age Type Address(es)
Before you can access the 6500 your VPN connection must be up.
Hopefully you are using ezvpn or you have the right pcf file for your
pod.
Mike Brooks
CCIE#16027 (RS)
On Sun, Nov 16, 2008 at 8:57 AM, M.Deniz KIZILCABOLUK
[EMAIL PROTECTED] wrote:
Ok Thanks,
Also How can I access 6500 ? On TS
IPs I have found for the 6500:
192.20.200.5
192.20.200.7
192.20.200.11
Which one you use depends on you pod. I eneded up telneting into each
and doing a sh port till i found my pod's ports.
M.Deniz KIZILCABOLUK wrote:
Ok Thanks,
Also How can I access 6500 ? On TS there is no host .. I
Hi,
Why I cannot see ipcc express in subsystem menu while I have premium
license?
Any idea?
Jeremy
Hi Mike,
Even I have the POD I need to set trunk and proper vlan on 6500 to reach
CCM. Am I wrong?
Thanks,
Deniz
2008/11/16 Mike Brooks [EMAIL PROTECTED]
Before you can access the 6500 your VPN connection must be up.
Hopefully you are using ezvpn or you have the right pcf file for your
Solved!
On Mon, Nov 17, 2008 at 1:12 AM, jeremy co [EMAIL PROTECTED] wrote:
Hi,
Why I cannot see ipcc express in subsystem menu while I have premium
license?
Any idea?
Jeremy
Hello all,
There was an issue with the Proctor Labs server that caused it to be down
for an hour at the beginning of the 8:00AM session today. We have
identified and resolved the issue so customers should now have access to
there session page. We will be issuing voucher codes for those customers
I'd like to set up the NM-HD-2VE module with a VIC-2MFT-T1 and VIC-1MFT-T1
cards to use in a Cisco 2610 so that I can set up a PSTN switch for my home
lab (this 2610 will also be used as a gatekeeper). I've only just started
looking at the NM-HD-2VE and would like to know if I need to purchase
Jeremy- If you still are having problems getting VM from Unity to CUE, check
the DNS setup.
I recently had this problem in the lab and it behaved the same way you are
describing.
Your FQDN for cue is se-200-0-0-100.cue.voice.com.
Make sure you can ping that from Unity.
You can also try nslookup
Hi chris,
it has 3 on-board DSP with 48 channels. I ran same setup in my lab. I
suggest u to buy following cards:
VIC-2MFT-T1
VIC-2MFT-E1
NM-HD-2VE
since u need some hands-on for E1 as well as T1.
HTH,
On Mon, Nov 17, 2008 at 2:02 AM, Chris Kagadis (kagadis.com)
[EMAIL PROTECTED] wrote:
Hey dude,
Thanks, when it comes to voice , cisco is buggy.
after spending hours last night, I left the problem unsolved.
As u mailed , I try to test it again and it works just required rest!
Cheers
On Mon, Nov 17, 2008 at 2:10 AM, Scott ODonnell [EMAIL PROTECTED]wrote:
Jeremy- If you
I have IPCC configured with both of my HQ phones PH3 (1003) and PH4
(1004) subscribed to the IPCC service. I can log into HQ PH3 as agent
1, but when I attempt to log in to IPCC with HQ PH4 it is already
logged in as agent1. If I log out on HQ PH4 then HQ PH3 logs out as
well. If I log into HQ
Hello,
call-manager-fallback
(...)
alias 1 2002 to 200 preference 1 cfw 91211007 timeout 10
^^^
Isn't it a mistake? Do you really want to route to number 200 not 2001 or
something?
--
Regards,
Bartosz
--
SOLIDEX S.A.
Tel: +48 12 638 04 80
Fax: +48 12 638 04 70
Hi,
I lost badly in JTAPI troubleshooting in ipcc, only thing I can say is jtapi
status is partial service and I cannot see anything added to trace when I
call triger number. e.g. 1700.
So I even donnow how to start troubleshooting for Jtapi problems.
any help would be appreciated.
Jeremy
Did you try to recreate the JTAPI configuration?Are you pointing towards the
SUB or PUB when you create the jtapi stuff?
- Scott
On Sun, Nov 16, 2008 at 11:48 AM, jeremy co [EMAIL PROTECTED] wrote:
Hi,
I lost badly in JTAPI troubleshooting in ipcc, only thing I can say is
jtapi status is
I am only referring to the Second Generation PVDM's (PVDM2)...as far as
the old style DSP's, I posted a similar question a few weeks ago and
never got a definitive answer...My question was how to calculate Extra
resources on the old style PVDM. I was looking for how many Xcoder
sessions will you
Hello,
I have IPCC configured with both of my HQ phones PH3 (1003) and PH4
(1004) subscribed to the IPCC service. I can log into HQ PH3 as agent
1, but when I attempt to log in to IPCC with HQ PH4 it is already
logged in as agent1. If I log out on HQ PH4 then HQ PH3 logs out as
well. If I
yes..thats what it is ...thanks Jacob.
On Sun, Nov 16, 2008 at 3:18 PM, Jacob Owen [EMAIL PROTECTED] wrote:
Mike,
Are you using EZVPN and phones at your house as the HQ Phones 3 4? If so,
i found it could be that both phones are seen from IPCC as the same device
(IP) since technically they
Hi:
If for some reason one of the IP Phones of a branch office can't register to
the SRST gateway we can forward all the calls for the non-registered phone
to a another phone in another Branch office, testing this I found that the
only way to make it work is using the command like this
alias 1
Ryan,
I tried to chase down this answer yesterday. I ended up using the calculator
URL referenced in the SRND. I tried alot of combonations and whether I did
MLPPP o/Frame or FRF.12 , the calculator kept serving up the same answer
whenever I checked the CRTP checkbox on the calculator : 16k
-
Do you have the config?
On Thu, Nov 13, 2008 at 4:45 PM, James Key [EMAIL PROTECTED] wrote:
Are you using the MGCP bind commands? If so, try removing these and
re-add.
James
*From:* [EMAIL PROTECTED] [mailto:
[EMAIL PROTECTED] *On Behalf Of *Erwan Erwan
*Sent:* Thursday, November
hi tks James , yes it work, just remove and re-add bind command
--- On Mon, 11/17/08, Ryan Trauernicht [EMAIL PROTECTED] wrote:
From: Ryan Trauernicht [EMAIL PROTECTED]
Subject: Re: [OSL | CCIE_Voice] MGCP gateway not registered ?
To: James Key [EMAIL PROTECTED]
Cc: [EMAIL PROTECTED],
Hey Barosz,
That's typo please , the command I gave was ---
alias 1 2002 to 2000 preference 1 cfw 91211007 timeout 10
I tried this woth and wothout dial-pattern command under call-manager-fallback
Have you ever made this working please...
Vik - can you please some light on this...can't
Hello Group,
I am doing Task 3.46 of Workbook volume 3.
Not sure in case of MLP LFI do we need the bandwitdh command in serial
subinterface or not please.
Thanks in advance.
Regards,
Anil
33 matches
Mail list logo
