Hi List,
lets assume we are required to configure Unity with 3 Ports + 1 MWI Port.
Normally all Voicemail Ports are in a Line Group. Would you leave the MWI
Voicemail Port also in the Line Group or would you exclude the MWI Voicemail
Port from the Line Group?
/Robert
Should the port connecting to the ATA186 be dot1q or not? Since the 186
doesn't have an ethernet port for a PC I guess its optional?
Hi Chris,
i configure the switchport for the ATA always as access-port. I would only
configure the switchport for dot1q if i am asked to explicitly.
/Robert
Chris Parkercpar...@cparker.us schrieb am Sonntag, 22. Februar 2009 um
14:48
in Nachricht b74096f513403f0e877b6a80074dcdb5:
Should
Hi List,
during my last Remote-Rack Sessions i noticed that the B-Channel Maintenance
Status Parameter is not workking properly. Always when i configured it and
restartet the CCM Srevice and the Gateway itself, it is working for some calls.
And suddenly the Gateway is trying to call out over
Robert is correct. the ATA 186 you should configure as an access port and
not dot1q. The ATA188 (which have a PC port) you would configure as a dot1q
port, but they are not on the lab.
Thank,
Ryan Trauernicht
CCIE Voice #23497
On Sun, Feb 22, 2009 at 8:53 AM, Robert Schuknecht
I would exclude the MWI port in the line group. If it is not answering
calls (you have unchecked that function on the unity side) there is no point
in putting it in the line group.
Thanks,
Ryan Trauernicht
CCIE Voice #23497
On Sun, Feb 22, 2009 at 6:05 AM, Robert Schuknecht
When you try this again what does Perfmon tell you the service of the
channels?
0, 1, 2, 3?
On Sun, Feb 22, 2009 at 11:07 AM, Robert Schuknecht rschukne...@gmx.dewrote:
Hi List,
during my last Remote-Rack Sessions i noticed that the B-Channel
Maintenance Status Parameter is not workking
Did you check off status polling on the device config for the circuit?
On Feb 22, 2009, at 12:10 PM, Ryan Trauernicht wrote:
When you try this again what does Perfmon tell you the service of
the channels?
0, 1, 2, 3?
On Sun, Feb 22, 2009 at 11:07 AM, Robert Schuknecht rschukne...@gmx.de
You can confgure the ATA as an access port or as a trunk- the Opflags
parameter allows for 802.1Q encapsulation and CDP discovery of the Voice or
Auxiliaryvlan. This also allows the ATA to support layer 2 COS- the default
is 3 and 5 for signaling for media.
--
Vik Malhi CCIE #13890, CCSI #31584
I've battled with this service parameter for over 5 years. It doesn't work
properly- I would use Top-Down with a fractional PRI.
But if you are trying to get it working you must ensure that you Enable
Status Poll on the gateway page. Also- you could try including a space
after every 4 bits
The 13 bytes for MLP mentioned on pg 1-15 has been subject for many debates
on this list. Everybody has there own conclusion. Mine is that in the lab I
would treat the 13 bytes as including the FR header and hence this is the
value that I would use. I think if you use the codec calculator tool it
If the MWI port should ONLY be used for MWI and nothing else - then there is
no reason why it should be in the Line Group. Only ports that answer calls
as defined in UTIM should be in the Line Group.
--
Vik Malhi CCIE #13890, CCSI #31584
Senior Technical Instructor - IPexpert, Inc.
Telephone:
Vik,
If thats the case, I'd think it'd be preferable to use the dot1q voice
vlan because if you set the port as an access port, you must trust the
dscp and I believe the ATA does not use CS3 for signaling by default? I
think to have it use CS3 for signaling you must set the TOS parameter to
Sometimes you have to insert the fields S0/ds...@sda000332333241 = 0001
and update. Then, due to a feature, you might have to
remove the field (via cut), click update, and insert the field again (via
paste). Call it the apply, rinse, repeat method.
Also, status
If you are trusting the device - Yes.
--
Vik Malhi CCIE #13890, CCSI #31584
Senior Technical Instructor - IPexpert, Inc.
Telephone: +1.810.326.1444
Fax: +1.810.454.0130
Mailto: vma...@ipexpert.com
Join our free online support and peer group communities:
http://www.IPexpert.com/communities
The parameter tends not to stick properly. In other words, you
configure it but it doesn't seem to work - fix is usually just to go
back to the SP page and take it out, do an update, then put it back
in, do an update. That should fix it. If it doesn't - rinse and
repeat. I have usually
I am connecting to my PODs at PL via EZVPN and have issues when trying to
RDP into the Unity servers (CCM Pub and Sub are fine). When I attempt to
RDP into Unity it opens and I just get a black screen same with VNC. I
actually have to RDP to Unity using the TS client on the Pub or Sub. Anyone
Agreed! It does not work well at all. I typically will have calls
incoming / outgoing the 6608 PRI and make a call 1 hour later to find
that the call fails. After a fitting Microsoft salute (reset), the call
goies through...
Scott Hardesty | Solutions Engineer | MidAtlantic | Presidio
Hey Vik
That's an interesting point. I never thought ATA can also be configured as
Trunk as well as i've always configured it as access port but you've cleared
the confusion. What would you recommend? ATA port to be configured as
Access or Trunk as a best practice?
Regards
- Basant
On Sun,
WHAT IS THE COMMAND FOR BR2 PHONE 3 UNABLE INITIATE A CONFERENCE ?
_
Show them the way! Add maps and directions to your party invites.
http://www.microsoft.com/windows/windowslive/products/events.aspx
Have CCM--- GK Controlled ICT (G.729) -- CME -- CFNA (or direct to
VM) --CUE.
With IOS 12.4(3) call gets to CUE, but no audio. With IOS 12.4(23) call
gets fast busy (tried changing IOS incase DSP firmware issue or bug).
I have xcoders on CME...here is the output of show sccp:
SCCP Admin
21 matches
Mail list logo
