Yes, it is there.
Warm Regards,
Vinay Kumar
From:
Rogers Ochieng rogersochi...@gmail.com
To:
Vinay Kumar6/India/IBM@IBMIN
Cc:
ccie_voice@onlinestudylist.com
Date:
04/29/2011 10:25 AM
Subject:
Re: [OSL | CCIE_Voice] RSVP based CAC
do you have this under your IOS dspfarm profile Mtp
Check your source interface (bind), CUCM must be registered with the same bind
interface mentioned in the mgcp configuration.
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Rrcrumm
Sent: Friday, April 29, 2011 8:05 AM
To: Adil Shaikh
Have you set ip rsvp bandwidth in the serial interface?
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Vinay Kumar6
Sent: Friday, April 29, 2011 9:58 AM
To: Rogers Ochieng
Cc: ccie_voice@onlinestudylist.com
Subject: Re: [OSL |
Following is the config on the routers.
interface Serial0/0/0.1 point-to-point
ip address 10.10.1.1 255.255.255.0
ip ospf mtu-ignore
snmp trap link-status
frame-relay interface-dlci 401
ip rsvp bandwidth 40
dspfarm profile 2 mtp
codec g729r8
codec pass-through
rsvp
maximum sessions
1. show sccp
2. show sccp connections
3. show sccp connections details
4. show sccp connections rsvp
5. show ip rsvp installed
6. show sccp statistics
7. debug sccp all
8. debug call rsvp-sync [events | func-trace]
On 29 April 2011 10:28, Vinay Kumar6 vinayjaisw...@in.ibm.com wrote:
*Following
Here is the link with troubleshooting guid
http://www.cisco.com/en/US/docs/ios/voice/cminterop/configuration/guide/vc_rsvp_agent.pdf
On 29 April 2011 10:32, Rogers Ochieng rogersochi...@gmail.com wrote:
1. show sccp
2. show sccp connections
3. show sccp connections details
4. show sccp
Finally got it worked.
I figured out that actually the call is connecting at h323 GW. I had to
uncheck Wait for far end TCS and same old config it is working perfectly.
Can anyone try.
Here is the router config
voice service voip
allow-connections h323 to h323
allow-connections h323 to
What is the codec between regions? Make sure you're using g729 and disable the
g722 advertising and also the iLBC
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Vinay Kumar6
Sent: Friday, April 29, 2011 11:28 AM
Cc:
Have you checked the status of your MTP on CUCM (make sure It’s registred)
Naoufal
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Naoufal Kerboute
Sent: Friday, April 29, 2011 11:10 AM
To: Rrcrumm; Adil Shaikh
Cc:
Codec is g729 and g722 is disabled in enterprise parameters.
From the debug on the gateways I found a message which says RSVP
Confirmation not required.
Warm Regards,
Vinay
From:
Naoufal Kerboute naou...@mhdinfotech.com
To:
Vinay Kumar6/India/IBM@IBMIN
Cc:
Hey Adil,
Did you add a new sip trunk security profile with allow subscription ticked?
Just double check that.
As well on CUPS in gateway section, did you put CUCM pub or sub? It ha to be
pub.
Only pub generates presence subscription notifications even though on a sip
trunk you might have DP
In CUCME study for 7.1
Sent from my iPad
On 28 Apr 2011, at 22:43, Abel ... midga...@gmail.com wrote:
Hi everyone, the following list is the recommended software to be use on lab,
is ok use the same version under the major release or must be use the higher
version under minor release
Hi Experts,
i am purchasing 4 phones to be used for IP expert Hardware VPN , i will like to
know if i can use 3 additional softphones so as to have 7 phones in all so that
i can practice all configurations.
Thanks for your prompt response
Regards
Pithog Oil
hi george,
thanks for the input.
i have 4 ticks in SIP profile
Accept Presence Subscription Accept Out-of-Dialog REFER Accept Unsolicited
Notification Accept Replaces Header
i have a put PUB as a gateway.
the CUPC is working for one user. also, voicemail is working with web
application
On lab CUCME 7.0 is required since Ben confirmed.
Peter
- Original Message -
From: George Goglidze gogli...@gmail.com
Date: Friday, April 29, 2011 11:16 am
Subject: Re: [OSL | CCIE_Voice] SW Version for Lab
To: Abel ... midga...@gmail.com
Cc: ccie_voice@onlinestudylist.com
Have you checked the status of your MTP on CUCM (make sure It’s registred)
Naoufal
From: Vinay Kumar6 [mailto:vinayjaisw...@in.ibm.com]
Sent: Friday, April 29, 2011 12:33 PM
To: Naoufal Kerboute
Cc: ccie_voice@onlinestudylist.com; ccie_voice-boun...@onlinestudylist.com
Subject: RE: [OSL |
Yes, It is registered.
Apr 29 10:47:45.600: RSVP 10.10.11.1_17198-10.10.10.1_17944[0.0.0.0]:
RESV: no path information for 10.10.10.1
Where 10.10.10.1 is HQ MTP and 10.10.11.1 is BR MTP IP.
because of which the RSVP is not getting initiated.
Not sure how to fix this.
Warm Regards,
Vinay
Can you paste the full config of your HQ and BR1 routers. If you remove the
rsvp, you can make calls between HQ and BR1?
From: Vinay Kumar6 [mailto:vinayjaisw...@in.ibm.com]
Sent: Friday, April 29, 2011 3:10 PM
To: Naoufal Kerboute
Cc: ccie_voice@onlinestudylist.com;
If you bump up the ip rsvp bandwidth command on the routers to a much higher
number (say 120), does the call go through?
If so, do you have any shared lines configured across sites on the phones? I
recall a bug whereby this can trigger a “two call worst case bandwidth”
scenario (e.g., need
Hi Adil - a couple of things to check in CUPS are:
under system / service param / cup proxy
- ensure you have a domain name set
- change authentication module status to 'off'
hth
Brian
On Fri, Apr 29, 2011 at 10:48 AM, Adil Shaikh adil.sha...@gmail.com wrote:
hi george,
thanks for the
Why 7.1 ?
Regards
Sent from my iPad
On 29/04/2011, at 8:59 PM, George Goglidze gogli...@gmail.com wrote:
In CUCME study for 7.1
Sent from my iPad
On 28 Apr 2011, at 22:43, Abel ... midga...@gmail.com wrote:
Hi everyone, the following list is the recommended software to be use on
When your IPPhones register on SRST gateway, gateway learn all ipphones
configuration and translate it into dial-peers. With srst mode
autoprovision all command you can read the built configuration from a show
run thanks to that command.
When UCM is available again, your ipphones unregister from
Because the version of IOS that blueprint says might contain 7.1 version, and
you might as well know it. There are just a few more features...
Blueprint says it can be 12.4T, so if they have 12.4(24)T then they have 7.1
I'm just saying it's possible... As they say any major software release is
Here is the official list of HW and SW in the lab -
https://learningnetwork.cisco.com/docs/DOC-5292
All 7.0, particularly 7.0.1 as others have mentioned below.
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Amit Singh
Sent:
Ben confirmed that the version of IOS that is in the lab is 12.4(20)T2.
Nothing later. Therefore, your version of CUCME is 7.0.1. If you are studying
for CUCME 7.1 then you are studying additional elements which are NOT tested in
the lab. There is already enough to the current blueprint
hi julien,
as per cisco SRND/doc.
there are 3 auto prov (none, dn,all)
and when we back to UCM from SRST, we should see the ephone and dn for auto
prov all. (that is why there is none optio )
Am I misunderstand it ?
On Fri, Apr 29, 2011 at 6:55 AM, Julien Krieger
Can anyone offer experience with attempting to run a SCCP and SIP
phone on CME at the same time?
I keep running into problems getting the phones registered (one as
SCCP and one as SIP)
The only way I've been able to get both to register is to issue no
create profile under voice register global ,
Hi Scott,
It's the first time I hear about this problem... Which IOS are you running?
Can you post the whole configuration?
I'd say could be some bug on a particular platform you're running, but can't be
sure.
Sent from my iPad
On 29 Apr 2011, at 19:51, Scott ODonnell
Hi Scott - CME load upgrades usually relate to version upgrade
incompatabilities, unless being specifically asked to move to use a specfic
version
just take out the load command in telephony-service and voice-register pool.
If you are looking to convert load between SIP/SCCP using CUCM is
Actually, it's not all that difficult.
If you examine the phone load files, they do use common components, except for
three files.
As an example, an SCCP load for version 8.3.3 for a 7962/7942 comprises the
following files:
apps42.8-3-2-27.sbn
cnu42.8-3-2-27.sbn
dsp42.8-3-2-27.sbn
Hello,
no problem here running it
config
voice register global
mode cme
source-address 10.10.202.1 port 5060
max-dn 2
max-pool 2
load 7962 SIP42.8-5-2SR1S
authenticate register
time-format 24
date-format D/M/Y
tftp-path flash:
create profile sync 00875500550A
!
voice register dn
I have used CUCM to load firmware before but always just pointed the phone
completely to the CUCM but if we could proxy off the phone loads on CME that
would be really nice. Can we do that?
On Fri, Apr 29, 2011 at 3:09 PM, Hough, Earl
earl.ho...@pcmallservices.comwrote:
Actually, it's not all
Earl,
I think you got me on the right path now.
I've gotten into trouble having the termxx.default.loads file
referenced in the tftp-server section.
I guess this file really only comes into play if the phone is
auto-registering as a new phone into the system. Is this correct?
I also noticed
does anyone exp proctorlab , very slow now? can't do lab properly
--- On Thu, 4/28/11, Naoufal Kerboute naou...@mhdinfotech.com wrote:
From: Naoufal Kerboute naou...@mhdinfotech.com
Subject: [OSL | CCIE_Voice] Proctor is DOWN
To: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com
34 matches
Mail list logo