Hello John ,
You thinking is correct however as the Packet will traverse over the
wan , it will be always subject to get modified by a lot of SW to
change specially the DSCP Value and so the QOS SRND recommend to Not
trust the packets coming from the wan and so we dont trust in the
Branches route
Hello,
In Workbook 2, Lab 10, question 5.2 it asks you to setup MLP LFI
between HQ and BR1. In the solution guide it has you use auto qos trust
on the HQ side but does not use trust on the BR1 side. The DSG guide
says the reason for not using the trust key word is because of the
following:
Hello Errol ,
This issue usually mean you have incorrect Host/ processNode files in
your PUB or the Sub and so the communication is broken between the PUB
and the SUB and you have to find what table we have corrupted and fix
it , or you have a big timing difference reported by your NTP ,
can you
the issue you facing is a L2 protocol mismatch issue , The ISDN you
using is Qsig so you using Qsig tunneling ? what is your other side
switch talking ? and what do you have configured on the CCM config
page ?
Let me see the debug output please
Deb mgcp pack
deb isdn q921
Ash
On Mon, Jan 16
Change the server address from hostname to ip?
Sent from my iPhone
Pls pardon my fat fingers.
On 17 Jan, 2012, at 7:15 AM, Errol Abrahams wrote:
>
>
> Hi All,
>
> I had a problem with my VMWARE Server and I had to rebuilt the system from
> scratch. I have reloaded PUB,SUB,CUPS,CUC and CUCC
Hi All,
I had a problem with my VMWARE Server and I had to rebuilt the system from
scratch. I have reloaded PUB,SUB,CUPS,CUC and CUCCX and all virtual
addresses are pingable. When I activate the services for the PUB from the
Cisco Unified Serviceability screen, it worked. But, when I try to access
No it wont ignore TP. Its only to provide differenet levels of control based on
need, i.e whether you want it on rp, rl, xformationx
Regards,
Mohammed Al Baqari
Sent from my iPhone
On Jan 12, 2012, at 1:18 AM, datucha123 datucha123 wrote:
> Hello,
>
> Can you please explain the idea of "Use
The idea is that MMoH wont trigger CAC calculation (location or rsvp). So the
stream will pass from CUCM directly to endpoint ignoring CAC.
Regards,
Mohammed Al Baqari
Sent from my iPhone
On Jan 12, 2012, at 5:34 PM, datucha123 datucha123 wrote:
> I have tested today, and Boris is right. The
Sold.
From: Qq Ccie
To: "ccie_voice@onlinestudylist.com"
Sent: Monday, January 16, 2012 2:25 PM
Subject: [OSL | CCIE_Voice] ccie voice lab equipment for sale
Dell PowerEdge T110 for sale with the following setup.
CPU Cores: 4 CPUs x 2.526 GH
Dell PowerEdge T110 for sale with the following setup.
CPU Cores: 4 CPUs x 2.526 GHz
Processor Type: Intel(R) Xeon(R) CPU X3440@ 2.53 GHz
Logical Processors: 8
Memory: 8 G
Hard drive: 1 TB
Software:
VMWare ESXi 4.1.0 (License vSphere 4 En
Hi mercy, did you try to put the DN number on this particular ISDN? Is the
switch-type already correct according to the provider?
Salam,
Suhandi
Sent from Samsung tablet
mercy forall wrote:
this is :-
"show isdn status"
\
Global ISDN Switchtype = primary-qsig
%Q.931 is backhaul
Hi Datucha,
Actually for CUPS you need only line association. you do not need to
specify owner user id.
Misread the question a little bit initially.
the owner user id on the phone is for SNR.
Cheers,
On Mon, Jan 16, 2012 at 4:01 PM, George Goglidze wrote:
> correctisimo :-)
>
>
>
> On Mon,
What is the output of your debug q921 ?
Something like
Q921: User RX <- SABMEp sapi=0 tei=0
Q921: S4_SABME: BACKHAULED & vsc_wants_L2_up = FALSE
If so you have hit the bug
Do a
No mgcp
No mgcp bind control
No mgcp bind media
mgcp
mgcp bind control source-interface GigabitEthernet0/0.1
mgcp
Take a look at the mgcp call agent version. You specify 1.0 but should use
0.1 for callmanager.
On 16 Jan 2012 14:58, "Justin McIntyre"
wrote:
I noticed two things...
1. It seems that the ccm-manager config server is there but not
"ccm-manager config" Not sure if that's absolutely needed or n
correctisimo :-)
On Mon, Jan 16, 2012 at 3:25 PM, datucha123 datucha123 wrote:
> When configuring the simple BLF Speed Dial, we need to configure the
> Subscribe CSS for watching Device. So that it could the the Watched DN.
>
> But, the Owner User ID, Line Association with End User and other
I noticed two things...
1. It seems that the ccm-manager config server is there but not "ccm-manager
config" Not sure if that's absolutely needed or not but I have always put it
in if I am going to let the CM configure the gateway.
2. I see that control is bound to a sub-interface. I'm prett
When configuring the simple BLF Speed Dial, we need to configure the
Subscribe CSS for watching Device. So that it could the the Watched DN.
But, the Owner User ID, Line Association with End User and other kinds of
associations are not required for this BLF, right?
Even for Call List Presence.
Agreed as to how it is configured via TFTP or manually?
Also on 7.0, I have found it better to register without the bind commands,
then once registered then add the bind commands back in
On Mon, Jan 16, 2012 at 8:01 AM, George Goglidze wrote:
> Hi Mercy,
>
> Did you configure this via tftp or m
Hi Mercy,
Did you configure this via tftp or manually?
I'm asking because you've got this: ccm-manager config server x.x.x.x
Can you do:
*debug ccm-manager config-download all
*then do *
no ccm-manager config
ccm-manager config*
And see if you are being able to download the config. paste the ou
this is :-
"show isdn status"
\Global ISDN Switchtype = primary-qsig
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not
apply
ISDN Serial0/2/0:15 interfacedsl 0, interface ISDN Switchtype =
primary-qsig Slave side configuration L
What does the "show isdn status" shows up?
On Mon, Jan 16, 2012 at 5:35 PM, mercy forall wrote:
> Hi,
>
> thanks for your support and good link\
>
> this is my GW configuration , also it is connected to other cisco GW as
> PSTN GW through E1 cross cable
>
> sh run :
> Current configuration : 15
Hi,
thanks for your support and good link\
this is my GW configuration , also it is connected to other cisco GW as PSTN GW
through E1 cross cable
sh run :Current configuration : 15381 bytes!
!version 15.0service timestamps debug datetime msecservice timestamps log
datetime msecno service passwor
Hi,
The card is supported:
http://www.cisco.com/en/US/prod/collateral/routers/ps259/product_data_sheet0900aecd8057f2e0.pdf
Paste your voice gateway configuration, there must be a problem somewhere.
Cheers,
On Sun, Jan 15, 2012 at 8:45 PM, mercy forall wrote:
>
> Hi,
>
> I think the issue from
Hi,
Thanks for the people who unicasted me -> In case anyone google for this
and go thru the same issue I had, the solution was changing the encoding to
UTF-8. A great CSV editor I was working with was XTabulator, you open the
file when exporting data from CCM and it shows perfectly. The free vers
24 matches
Mail list logo
