Hi AllI'm running my lab in W8.1 64bits, vmware workstation 10, core i7, 16GB RAM, 480GB SSD for vmware and 100GB SSD for OS.And works like a champ. It's been some dificult to tune up but is worth.If you go with vmware workstation feel free to ask if you found problems in your way.best regards.On
HiFor telephony-serviceI used:srst mode auto-provision allsrst dn line-mode dualAnd for call-manager-fallback I used:max-ephone 4max-dn 8 dual-lineAm I wrong using these configurations?I avoid octo-lines for the bug mentioned.best regards!AlexOn Oct 17, 2013, at 10:18 AM, Ramcharan Arya
As Dave says, you can book at Tokyo or other location.
I'm from Mexico and can book at RTP in february just one week ago.
More pressure because will be my 2nd and last attempt.
If you are so close to get your CCIE, look for a seat at other location even if
you must pay for travel expenses.
If you pass only the written on voice, you must take the lab before Feb 14th
2014 and pass.
After this date you will stay on ground zero.
best regards
On Sep 19, 2013, at 6:57 AM, Edward Hawkins hawkins.edw...@gmail.com wrote:
So what happens if you only pass the ccie voice written. Does
Hi all
Please share your thoughts.
What option will you do on this one.
Create speed dial *3001 on device and then...
Note: is unity connection
Option 1
Create a dn *3001 with fwd all to vm checked, VM profile mask with to
strip *
Option 2
Create a new partition and CSS
Create a dn
Hello guysCould you please share your thoughts on this simple question.When I used mgcp on a gw the ip phone shows the called number without 9.but if I used H323 the called number on ipphone'sshows the called numberwith 9, because all my dial-peer starts with 9 for SRST.My doubt is when im using a
Hi, Hesham.
Connect the ip phone (black screen) to a PoE switch, turn on debug ip DHCP
server all to see if the ip phone are trying to get an IP address.
If not, I don't know what to do, but If the phone are trying to get an IP
address you can use a CME to put a correct firmware and bring
Hi, All
Is mandatory in Subscriber, TFTP server activated?
I'll activate TFTP on sub until I finished all tasks (hope so)
What do you think?
best regards!
___
For more information regarding industry leading CCIE Lab training, please visit
detailedHthSent from my Windows PhoneFrom: Alex Mendoza Sent: 8/26/2013 10:54 PMTo: CCIE Study Subject: [OSL | CCIE_Voice] LAN QoS on HWIC-4ESWHi All,I'm wondering about QoS on remote site.I just applied auto-qos between HQ and remote site, everything looks fine.When I run this command on both
Hi All.Is there a solution on this...GW (h323) is configured with Outbound Fast Start using IOS MTP software and is working good."Media Termination Point Required" box checked"Enable Outbound FastStart"box checked with G711u-law 64KAlso, I configure Multicast MoH for this site and is working good
Hi All,I'm wondering about QoS on remote site.I just applied auto-qos between HQ and remote site, everything looks fine.When I run this command on both routers, in remote site I can't see packets.HQ Class-map: AutoQoS-VoIP-RTP-Trust (match-any) 11139 packets, 704260 bytes 5 minute offered
Hi colleaguesI set up mva and I think is working good, but I don't know if this is an issue.Calling from my SNR to MVA is working, MVA asks for my pin number, then press 1, after that I dialed internal 4 digit extension but this internal phoneonly shows the caller number and not the caller name.I
Hi All
I configured BR1 as a MGCP gateway, and is working good.
Call takes Bchan 1 on incoming and outgoing calls.
My doubts are with mgcp-fallback. On SRST mode, outgoing calls take bchan 3. I
used the isdn bchan-number-order ascending to fix this.
It's valid use this command or there is
Must check your routes
Try pinging the ip phone's address from CUPC PC.
If it is unsuccessful do a tracert, to see which hop do not know how to reach
the voice vlan.
I think is easy to figure out what is going on.
Best regards
Alejandro Mendoza
Sent from my iPhone
On 24/07/2013, at
, at 22:43, Pavan K pav.c...@gmail.com wrote:
Its most likely a firewall blocking rtp. Cannot be routes as the signaling is
OK (as you have ring back)
On Jul 24, 2013 9:20 PM, Alex Mendoza aa.mend...@icloud.com wrote:
Must check your routes
Try pinging the ip phone's address from CUPC PC
/07/2013, at 23:59, Devakanth Gangavarapu devakanth2...@gmail.com wrote:
If there is a routing issue, the CUPC would not get registered to CUCM :)
Dev
On Thu, Jul 25, 2013 at 3:50 PM, Alex Mendoza aa.mend...@icloud.com wrote:
Could be FW and maybe a wan accelerator as well
But you
Hi
I'm not an expert on this field but I think the problem is the mod-call
signaling
Did you know if the IP address of your CUC is trusted? Maybe this behavior is
for a toll-fraud prevention.
Regards
AM
Sent from my iPhone
On 16/07/2013, at 05:11, Ashok Boinpally ping.as...@gmail.com
Hi I want to do the lab guide for this workbook (UCCXDv3) but I don't know much about DB, and I'm stuck in the lab 3-4.I see in a reference that I need to follow this procedure to create the db that is needed in this workbook ... but the sever does not have installed the MSSQL7, from where do I
Hello,
I finished the kevin's videos, but I have some issues that are not mentioned on
the video (or I missed).
1.- MoH between HQ and BR2 is not working, is this an expected behaviour?
2.- If I call to Br2 phone (4001) from HQ phone (2001) via gatekeeper, and
brph2 divert to voicemail I got
Hello Experts
Silly question,
I'm not looking in deep regarding this but let me ask first maybe is something
easy to resolve.
When I call from PSTN phone to IPCC CSQ (task 9.2 from kevin's videos).
I should hear thank you for calling all representative … instead I hear you
for calling all
Did you know the official date for new version?
I assume that I'll be ready for Sep/oct 2013
Best Regards
AA Mendoza
Sent from my iPhone
On 28/04/2013, at 10:33, Robert Thomas tho...@gmail.com wrote:
Hi,
I'm thinking on buying a home lab to start my studies.
It would run around 3K
Which version of VMware did you use to create this images?
You can use VMware workstation 9 to change the compatibility to open with
esxi5.1
Regards
AA
Sent from my iPhone
On 21/04/2013, at 06:53, Hesham Abdelkereem heshamcentr...@gmail.com wrote:
Dear Experts,
I am building my
Hello partners
Can I do the training lab with this model 7960 ?
I have doubts about the presence tasks
Thanks in advanced
AA
___
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or
I think the GW was associated to a route pattern and as a consequence you can't
see it in the route group configuration page.
When you deleted the GW, the route patter miss the gateway association and then
you can see it in the route group configuration page.
AA Mendoza
Sent from my iPhone
Hi Vir,
I complete this task using a ISR 2851(is the same that I'm using as PSTN),
VWIC2-2MFT-T1/E1 cards and RJ45 cross cables.
Read this blogs/post.
25 matches
Mail list logo