You don't need those commands on site b in the following scenarios:
1-you are using unicast moh
2-you are using moh from flash at site b
You *should* need those commands to achieve multicast moh from site a cucm
over wan to site b phones.
On Aug 22, 2013 2:46 PM, "Karen Johnson" wrote:
>
> all,
all,
i am just curious, my MOH SB for multicast always work without "ip
multicast-routing" and "ip pim dense-mode"
do we really need enable MCAST for moh to work ? And why without Mcats it
also works ?
K___
For more information regarding in
Karen
Do you have ccm-manager music-on-hold configured on the global config?
On Aug 11, 2013 1:35 PM, "Karen Johnson" wrote:
> folks,
>
> I try to configure MOH using multicast for SB site.
>
> here is what i did :
> =
> SB router:
> --
>
> call-manager-fallback
>
folks,
I try to configure MOH using multicast for SB site.
here is what i did :
=
SB router:
--
call-manager-fallback
moh music-on-hold.au
multicast moh 239.1.1.1 po 16384 route 142.1.65.254 142.102.65.254
max-dn 20
max-ephone 10
ip so
e MOH from CUCM ?
Date: Sun, 9 Sep 2012 05:08:17 -0700
From: vinayak_...@yahoo.com
Subject: Re: [OSL | CCIE_Voice] MOH-Multicast not working
To: nehal.ah...@msn.com
nehal,
check the multicast ip address on the audio server, and make sure it is
assigned to the mrgl where site B device pool can see
Dear All,
I am stuck with the MOH Multicast.
I have followed the same steps as defined by IPEXPERT to get the MOH from the
Local Router using MOH. Whan I call from PSTN, I only hear the TOH.
I checked the region relationships for MOH (g711) , Device Pools and MRGLs
manytimes. I restarted the
Ok, In the SRND I see that redundancy is recommended. But the solution is not
describer clearly (for me)
From: Cisco Nut
Sent: Thursday, April 26, 2012 10:47 PM
To: Maik Stokman
Cc: CCIE Voice
Subject: Re: [OSL | CCIE_Voice] MOH Multicast MRG
Maik
I do not think there is any recommendation
Maik
I do not think there is any recommendation on configuring PUB as multicast
and SUB for unicast MOH. Usually its configured based on what is asked in
Practice lab or CCIE Voice Lab.
On Thu, Apr 26, 2012 at 2:22 AM, Maik Stokman wrote:
> Hi,
>
> When using Multicast MOH.
> What is the recomm
Hi,
When using Multicast MOH.
What is the recommended configuration for the Media Resource Groups.
Multicast enabled on PUB moh and placed in a MRG with multicast enabled.
Unicast MOH used on the SUB and placed in a MRG without multicast.
Do we also need to configure to PUB moh server for unica
l baqari ;
>> *To: *Ccie Voice ;
>> *Cc: *CCIE Study ;
>> *Subject: *Re: [OSL | CCIE_Voice] MOH multicast
>> *Sent: *Fri, Oct 14, 2011 3:24:18 PM
>>
>> use the CLI command [show perf query class "Cisco MOH Device"] on CUCM
>> CLI interface. The cou
14, 2011 at 11:44 PM, Ccie Voice wrote:
> But I am using router flash memory Not CUCM
>
> --
> * From: * Mohammed Al baqari ;
> * To: * Ccie Voice ;
> * Cc: * CCIE Study ;
> * Subject: * Re: [OSL | CCIE_Voice] MOH multicast
> * Sent: * Fri,
But I am using router flash memory Not CUCM___
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com
use the CLI command [show perf query class "Cisco MOH Device"] on CUCM CLI
interface. The count as below should be increased. This will reflect in CUCM
and not on BR1 router.
admin:show perf query class "Cisco MOH Device"
==>query class :
- Perf class (Cisco MOH Device) has instances and values:
Hi everybody,
I am trying to configure Multicast MOH in Branch 1 router, I added the file to
router flash and I configure CUCM to use multicast.
when I am calling from one phone to another in BR1 I am able to hear the file
that I uploaded to router flash memory. but if I tried to use the followi
p://www.twitter.com/iwan_ccie
LinkedIn: http://www.linkedin.com/in/iwanhoogendoorn
From: Roger Henderson [mailto:rhender...@gmail.com]
Sent: zaterdag 27 maart 2010 16:20
To: Iwan Hoogendoorn
Cc: Arun Kumar; ar...@ipexpert.com; ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] MOH Multicas
rom:* Roger Henderson [mailto:rhender...@gmail.com]
> *Sent:* zaterdag 27 maart 2010 16:18
> *To:* Iwan Hoogendoorn
> *Cc:* Arun Kumar; ar...@ipexpert.com; ccie_voice@onlinestudylist.com
>
> *Subject:* Re: [OSL | CCIE_Voice] MOH Multicast from Router flash
>
>
>
> Iwan, what di
LinkedIn: http://www.linkedin.com/in/iwanhoogendoorn
From: Roger Henderson [mailto:rhender...@gmail.com]
Sent: zaterdag 27 maart 2010 16:18
To: Iwan Hoogendoorn
Cc: Arun Kumar; ar...@ipexpert.com; ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] MOH Multicast from Router flash
Iwan, what did your tes
In: http://www.linkedin.com/in/iwanhoogendoorn
>
>
>
> *From:* Arun Kumar [mailto:arunv...@gmail.com]
> *Sent:* donderdag 18 maart 2010 7:08
> *To:* Iwan Hoogendoorn
> *Cc:* ccie_voice@onlinestudylist.com
> *Subject:* Re: [OSL | CCIE_Voice] MOH Multicast from Router flash
>
&
edIn: http://www.linkedin.com/in/iwanhoogendoorn
From: Arun Kumar [mailto:arunv...@gmail.com]
Sent: donderdag 18 maart 2010 7:08
To: Iwan Hoogendoorn
Cc: ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] MOH Multicast from Router flash
show ccm-manager music-on-hold
and you will
show ccm-manager music-on-hold
and you will see packet in/out value increasing.
On Thu, Mar 18, 2010 at 1:35 AM, Iwan Hoogendoorn wrote:
> Hello,
>
>
>
> I am trying to multicast MOH from router flash and was wondering if there
> is any way to verify live MOH feed when a call is placed on hol
.ipexpert.com> .
From: Iwan Hoogendoorn
Date: Wed, 17 Mar 2010 16:05:54 -0400
To: "ccie_voice@onlinestudylist.com"
Subject: [OSL | CCIE_Voice] MOH Multicast from Router flash
Hello,
I am trying to multicast MOH from router flash and was wondering if there is
any way to verify live M
Hello,
I am trying to multicast MOH from router flash and was wondering if there is
any way to verify live MOH feed when a call is placed on hold on the Proctorlab
Racks.
According to Proctorlabs there is no way to hear MOH trough Multicast because
of the the EzVPN (IPSec) connection...
So thi
| CCIE_Voice] MOH MULTICAST between ccm to cme is it possible?
Hi Zamuel,
Have you issue the command "ccm-manager music-on-hold" command on the
voice gateway? This command is needed in order for the voice gateway
to successfully receive multicast MoH as instructed by the UCM.
Hi Zamuel,
Have you issue the command "ccm-manager music-on-hold" command on the
voice gateway? This command is needed in order for the voice gateway
to successfully receive multicast MoH as instructed by the UCM.
Cheers,
Danny
zamuel del Toro wrote:
I have a phone on hq site calling to
I have a phone on hq site calling to ccme and hq phn put on hold the call and
the ccme user hear silence. the comunication is via direct gateway h323. and
the gateway have mrgl with moh multicast. when it used a mrgl with unicast mho
work fine.
it it possible use moh multicast?.
___
DO you see an output similar to this? You should do this when you put the
call on hold that is coming from PSTN phone.
PodX-BR1-RTR#show ccm-manager music-on-hold
Current active multicast sessions : 1
Multicast RTP port Packets Call CodecIncoming
Address number in
Create a regioun for g711 only
Create a device pool and assign g711 region to this pool
under services/media resource/ assign this region to one of the MOH server
that is also set up for multicast.
That is it.
On Sat, May 9, 2009 at 12:47 PM, Sowmyashree Mahadevaiah <
sowmyashr...@gmail.com> wrot
DId you put ccm-manager music-on-hold command?
also make sure that you have the g711 assiged to MOH and under
call-manager-fallback you got the routes with multicast moh command.
On Sat, May 9, 2009 at 10:47 AM, zamuel del Toro wrote:
> I have configured the gateway via h323 to psnt and the pstn
I have configured the gateway via h323 to psnt and the pstn phone side not
heard the moh audio. via mgcp work fine.
any ideas?
_
Get 5 GB of storage with Windows Live Hotmail.
http://windowslive.com/Explore/Hotmail?ocid=TXT_TAG
Sounds to me that you do not have multicast streams all the way through. If
you do a "show ip mroute" do you see a multicast stream coming from the
subscriber?
You might want to look at the max number of hops you have for the music on
hold server in CM to make sure it accommodates enough hops to
Hi:
I am testing MOH and using Subscriber as a multicast source and publisher as
a unicast source, everything is working good, however when I am testing the
call from CME in BR2 when I used multicast music on hold I don´t hear
anything in CME IP Phone, when I am using unicast is is working, I ena
Perfection. Thanks.
From: Alex [mailto:[EMAIL PROTECTED]
Sent: Tuesday, 11 November 2008 10:17 a.m.
To: James Jung; Vik Malhi; Ryan Trauernicht;
ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] MOH Multicast failover to Unicast
JamesJ,
You
Re: [OSL | CCIE_Voice] MOH Multicast failover to UnicastJamesJ,
You can configure unicast MOH server to be in a separate location. Then for
this location allow whatever x 24kbps BW for whatever number of unicast MOH
G729 streams you need to activate when multicast MOH server fails.
Rgds
Alex
Sorry, typo, 5 g729 calls.
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of James Jung
Sent: Tuesday, 11 November 2008 9:46 a.m.
To: Vik Malhi; Ryan Trauernicht; ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] MOH Multicast
: Tuesday, 11 November 2008 9:38 a.m.
To: Ryan Trauernicht; ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] MOH Multicast failover to Unicast
The failover should happen transparently.
To test you should stop the IP Voice Media Streaming App service on the
sub.
Unicast MOH is
and CCIE Storage
Lab Certifications.
From: Ryan Trauernicht <[EMAIL PROTECTED]>
Date: Sun, 9 Nov 2008 16:14:39 -0600
To:
Subject: [OSL | CCIE_Voice] MOH Multicast failover to Unicast
I have phone A at the headquarters that has a MRG1 of Sub (multicast) and
MRG2 of Pub (Unicast). Then
I have phone A at the headquarters that has a MRG1 of Sub (multicast) and
MRG2 of Pub (Unicast). Then in my MRGL I have MRG1 then MRG2.
If I shut down the Subscriber I lose all MOH. Am I missing something to
allow a Multicast MOH server failover to a Unicast MOH server?
37 matches
Mail list logo