Does anyone know if route summary is avaliable in rip
(v1/v2) on the cisco router. I know it can be down in
OSPF and EIGRP.
Thanks
Adam
__
Get personalized email addresses from Yahoo! Mail - only $35
a year! http://personal.mail.yahoo.com/
___
Hi Group,
A quick question. If a distribute list has be
established in EIGRP for a while, and you remove the
list. How long will it take for the new route to be
discovered? And how EIGRP is acting in this case.
Thanks in advance.
Adam
__
Do Yo
Hi group,
I have 2 PVCs setup using Frame Relay on a serial
interface with 2 subinterafces, and I want these 2
subinterfaces to backup each other when 1 fails.
I did backup interface s0.2, but it won't allow a
subinterface on the backup command, only the physical
interface. So backup interface
P address is distance 1.
>
> Kelly D Griffin, CCNA, CCDA
> Network Engineer
> Kg2 Network Design
> http://www.kg2.com
>
>
> - Original Message -
> From: "Adam Wang" <[EMAIL PROTECTED]>
> To: <[EMAIL PROTECTED]>
> Sent: Wednesday, Februar
Anyone know a good book on T1.
Thanks
Adam Wang
__
Do You Yahoo!?
Get email at your own domain with Yahoo! Mail.
http://personal.mail.yahoo.com/
_
FAQ, list archives, and subscription info: http
Hi group,
Anybody had done mass puchase with Cisco/its parnters.
Our company is roll out a project of purchasing over
$1 million of cisco equipments. We just want an idea
what discount rate can we get from the cisco list
price with this quantity (some say we can get as much
as 50%), and what di
Hi group
I'm trying to setup a 7100 with a HSSI card to connect
to Internet through a DS3. BGP will be the routing
protocol. Anyone has a sample config that I can use
as a reference? Any special commands for the HSSI
interface and DS3?
Your input will be greatly appreciated.
Adam
___
Hi group
How would I check statistics on a single nat entry
show ip nat statistics will give me the whole picture,
not individual entries.
Thanks
Adam
__
Do You Yahoo!?
Get email at your own domain with Yahoo! Mail.
http://personal.mail.yahoo.co
Hi all,
I want to build an access list on a cisco router that
will log all the denied traffic to a file/server. Can
this be done on the implicit deny statement or I have
to define the deny traffic.
Thanks
Adam
__
Do You Yahoo!?
Get email at yo
Hi,
I have a cat 3524 for an initial setup. I gave the
vlan1 (the management vlan) an ip address, but when I
look at the interface vlan1, the interface is up,
protocol is down. I can not go on to access its web
config page because I can't get this interface up.
Any idea what else I need to do
Hi group,
Passed CCDA today. 72 question, 755 to pass, scored
854. The exam itself is not too hard, but the way
Cisco presents the scenario questions is very
annoying.
4 scenarios are scattered among the 72 questions.
What I mean is you got 1 question on case 1, the next
question on case 4, t
e scenarios in the CCDA exam - by the time
> you have COL, COS and
> QOL, what chance have you got? :-)
>
> JMcL
> -- Forwarded by Jenny
> Mcleod/NSO/CSDA on 24/04/2001
> 09:53 am ---
>
>
> "Adam Wang" @groupstu
3rd day into my CID course with Mentor Tech. The
instructor Bill McInerney, a CCIE, seem to be a
well-rounded knowledgable guy. Good teaching skills
too.
Took a Nortel VPN class with global knowledge a few
weeks back, the instructor was not very knowledgable,
even in the security aspect (misint
Hi group,
I have a 2621 router with a serial and a FT1 WIC card
installed in it. I want to assign different timeslots
to the T1 cotroller, but when I am type controller ?
in the config mode, it tells me it's an unrecogmized
command. Is the controller t1 command not supported
on the FT1 WIC card
ible with
> this card?
>
> -Original Message-
> From: Adam Wang [mailto:[EMAIL PROTECTED]]
> Sent: 18 May 2001 15:37
> To: [EMAIL PROTECTED]
> Subject: trouble configure channle-group on WIC T1
> card [7:4983]
>
>
> Hi group,
>
> I have a 2621 router with a seri
Does anybody know what's the cheapest layer 3 Catalyst
I can get. Port number doesn't matter.
Thanks.
Adam
__
Do You Yahoo!?
Get personalized email addresses from Yahoo! Mail - only $35
a year! http://personal.mail.yahoo.com/
Message Posted
Hi group,
I have a router set up with 3 channel groups on the
serial side, and 3 VLANs using 802.1q on the ethernet
side. I want to use RIP2 for routing.
How would I setup routing so that the traffic always
follow the same path between the serial and ethernet
back and forth.
ie, s0.1 always go
6) 782.1535
> Desk: +1(646) 792.2395
> Mail: [EMAIL PROTECTED]
>
>
> -Original Message-
> From: Adam Wang [mailto:[EMAIL PROTECTED]]
> Sent: Friday, June 15, 2001 2:21 PM
> To: [EMAIL PROTECTED]
> Subject: channlized T1 into different VLAN config
> [7:8783]
>
&
I have a cisco 7206 with an ATM CES module.
The ISP hand off 3 T1s to us for a bundled 4.5 mb ATM
connection
Beside buy an IMA card to bundle the 3 T1s together,
is any other external mux (munufacturer and model)
that I can use for the same purpose with voice
capability?
Thanks
Adam
Hi group,
I have a few 7200 with ATM-CES adapters in them. I
want to depoly them over WAN with a 4.5 meg bandwidth
to each. The telco handed to us 3 T1s. I would
assume an IMA device of some kind is needed here.
However, I still want to use the existing ATM-CES
adapters for this case. How wo
Hi,
I have a question about CCDP certification. After I got a CCNP, do I still
need to take the CCDA plus the CID exam, or I only need to take the CID exam
to become a CCDP.
Thanks.
Adam
___
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
Hi,
I just finished my CCNP and want to move on to CCIE written. What
books/readings are recommended besides all the readings I have done to get
the CCNP.
Thanks.
Adam
___
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives,
Hi group,
Is there a way to filter the SNMP MIB sned out on a
cisco router.
For example, I want a community string only send out
router interface status info.
How would I accomplish this?
Thanks
Adam
__
Do You Yahoo!?
LAUNCH - Your Yahoo! Mus
23 matches
Mail list logo