Hello All,
I wanted to check out the possibility of configuring 2
MSFC for HSRP.
Please give your comments...
Regds
Amit
__
Do You Yahoo!?
Yahoo! Autos - Get free new car price quotes
http://autos.yahoo.com
Message Posted at:
hello All,
I am facing a strange problem with one of our UNIX
Servers.
I am able to ping and telnet from this UNIX machine to
any other server/machine but it pings occasionally the
other way round.
I have checked the speed and duplex settings on the
Cisco Catalyst switch and matched it with
Hello All,
I want to set up an access list on the MSFC so that
traffic from a particular vlan or a range of IP
addresses is forwarded through another serial
interface.
My Ip range is x.x.x.240 - x.x.x.255
We are using a Subnet Mask of /28
Any Clues ?
Thanks in Advance
Regards
Amit
Hello,
I have been booting my 3640 router through the tftp
server.
Recently I have installed a Flash Card and have loaded
the same IOS image in that too.
I want to configure my router to boot from the flash
card as the default option and in case of problems,
boot from the tftp server as a
Hello All,
I am facing some problems in making an end to end VoIP
call over an IPLC.We are using 4 wire em, type 5
signalling
The local loopback/ hairpinning is working fine at one
of the ends but it fails sometimes at the remote
end.The IPLC link is stable and has no errors.
Can someone
Hi Daniel,
We had a similar situation few days back. Users connected on One of our
switches were complaining of intermittent loss in connectivity.
We had a problem with the GBIC port on one of our Catalyst switch.
Regds
Amit
-Original Message-
: Amit Gupta
Reply-To: Amit Gupta
To: [EMAIL PROTECTED]
Subject: Source Quench [7:12477]
Date: Mon, 16 Jul 2001 10:29:14 -0400
Hi All,
I am getting a Source Quench message from one
of
my HP-UX Servers when I try to ping it from an NT
machine / Switch
I am getting the following msg
as far as I can tell.
So, source quench is not obsolete for hosts.
Priscilla
At 10:29 AM 7/16/01, Amit Gupta wrote:
Hi All,
I am getting a Source Quench message from one
of
my HP-UX Servers when I try to ping it from an NT
machine / Switch
I am getting the following msg when I ping
Hi All,
I am getting a Source Quench message from one of
my HP-UX Servers when I try to ping it from an NT
machine / Switch
I am getting the following msg when I ping the server
from the external router
Sending 5, 100-byte ICMP Echos to x.x.x.x timeout is 2
seconds:
Q
However if I
Hi Everyone,
I used the following cmd to get the following output.
Can somebody elaborate on what the parameters
lost/delay shown below indicate.
show call history voice brief
57EB : 288131106hs.11447 +845 +4266 pid:22 Originate
+78877462513
dur 00:00:34 tx:592/11840 rx:749/14980 10
Hi All,
The scenario is such that I have 2 subnets configured
on the LAN. They are x.x.1.0 / 24 and x.x.2.0 / 24.
The IP address for the Routers ethernet port are
x.x.1.1 and x.x.2.1. Similarly workstations in either
subnet point to these addresses ( x.x.1.1 and x.x.2.1
) as their default
Brian
On Thu, 31 May 2001, Amit Gupta
wrote:
Hi Everybody,
I have configured the following
parameters on the
Hi Everybody,
I have configured the following parameters on the
serial interface for VoIP.The quality of the calls is
not very good during working hours you can feel some
delay/small interruptions while using it.
interface serial 0
ip tcp header-compression iphc-format
no ip mroute-cache
no
Hi,
I am upgrading the bandwidth of my ISDN link which is
used as backup.I am adding another ISDN line to have a
bandwith of 256kbps ( 2 lines )
I am currently using ddr with floating static routes
and the remote router dials at our end when the
primary link is down.
I plan to use the foll
Hi,
I am upgrading the bandwidth of my ISDN link which is
used as backup.I am adding another ISDN line to have a
bandwith of 256kbps ( 2 lines )
I am currently using ddr with floating static routes
and the remote router dials at our end when the
primary link is down.
I plan to use the foll
Hi All,
I am using VoIP over a satellite link.
I am planning to configure some queuing mechanism on
the router which can provide dedicated bw to voice
traffic and at the same time use the entire bw for
data traffic when no traffic from higher priority
flows is available( voice )
Please send me
Hi All,
Help needed on the prerequisites in the form of IOS
for configuring VoIP over an International Leased
Private Circuit.
Do the Cisco Routers at both the sides have to have a
minimum IOS version.
We are using the 3640 Router at both ends.
Thanks Regards
Amit
Hi All,
I need some help for making the router SNMP enabled. I
am actually testing it out SNMP Manager Utility.
I am using the following commands on the router
snmp-server community hppublic RO
snmp-server enable traps snmp
snmp-server host x.x.x.x traps hppublic
where x.x.x.x is the IP
Hi All,
Just a thought on Whether Tcp/Ip can run over RS232
Interfaces.
Any comments please ?
Regds
Amit
__
Do You Yahoo!?
Yahoo! Auctions - Buy the things you want at great prices! http://auctions.yahoo.com/
_
(they will or no comms) and the duplex settings
(the most common problem). DO NOT LEAVE THE SWITCH IN AUTO NEGOTIATE
MODE.
Just some thoughts.
Teunis
Hobart, Tasmania
Australia
On Tuesday, January 02, 2001 at 05:25:17 AM, Amit Gupta wrote:
Hi Everybody,
Need some
Hi Everybody,
Need some help on the following problem
I have 2 subnets configured on my LAN say ( x.x.1.0
and x.x.2.0 )with a SM of 255.255.255.0.
There are 2 Catalyst switches ( each one on a
different subnet)
The router is configured with a primary and a
secondary address on the ethernet
Hi everybody,
I need assistance on the VoIP problem I am facing :
We are planning to have a VoIP setup on the already
existing data link between our local and remote
office.
Both sites have Cisco 3640 routers configured for it.
The router on the local site has IOS 11.3(9)T and the
remote
it from there as I think I am walking blindly into
this.
Tai
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]]On Behalf Of
Amit Gupta
Sent: 13 December 2000 11:27
To: [EMAIL PROTECTED]
Subject: Re : ISDN Backup
Hi All,
I am using the following config on my
Hi All,
I am using the following config on my router.
router eigrp xxx
redistribute static
passive-interface BRI1/0
network x.x.x.x
distribute-list 2 out Serial0/0
!
ip route 0.0.0.0 0.0.0.0 Serial0/0
ip route 0.0.0.0 0.0.0.0 bri1/0 150
I am using ISDN as the backup interface.
The
Title: Broadcasts on Serial interface
Hello All,
There has been a slow but steady increase in the number of broadcasts and input errors on the serial interface.
Can someone suggest please..
Thanks Regards
Amit
sh inter serial 0/0
Serial0/0 is up, line protocol is up
Hardware is
Title: Re : MAC Address to IP Address conversion
Hello All,
I am looking for some sniffer software that could show me a list of MAC Address to IP Address mapping of my network.
I checked with the trial copies of CNAPro and Sniffer PRO would could not find the functionality.
Can anyone
Title: RE: Re : MAC Address to IP Address conversion
Got the list from my Router's ARP cache
-Original Message-
From: Amit Gupta (EHPT) IS-IT [SMTP:[EMAIL PROTECTED]]
Sent: Sunday, November 26, 2000 3:19 PM
To: '[EMAIL PROTECTED]'
Subject: Re : MAC Address to IP Address conversion
Hello ,
I am facing a problem of large number of collisions
in the network
and would like to have your help on this
We have 2 Catalyst switches , 5509 and 6009 cascaded
together and all the
ports are configured in the Autonegotiating mode.
The following is the sh interface from the router
Title: RE: question : ethernet collision rule of thumb...
Hi ,
How can I find out the collision rate of .1% ( comparing the collisions with Output packets or bytes)
Here's the output from my ethernet interface
119069488 packets output, 3373784736 bytes, 0 underruns
31 output errors,
Title: CCNP Preparation library
Hi everybody,
Is the CCNP Prep Library ( 2nd Edition ) from Cisco Press available in bookstores in US ?
Thanks Regards
Amit
Hi All,
Need some help in configuring VoIP
I am testing the loopback connectivity between my
router and EPABX by dialing a local extension number.
As Soon as I dial the seizing code I get connected to
the router.
When I dial the destination pattern my call gets
transferred to the router,s next
Title: PAgP Message
Hi,
I am preparing for the CCNP Exams. I would like to know the reason for the following messages i am getting on my 6009 switch.
6000 (enable) 2000 Nov 07 01:39:08 %PAGP-5-PORTFROMSTP:Port 2/46 left bridg
e port 2/46
2000 Nov 07 01:39:10 %PAGP-5-PORTTOSTP:Port 2/46
32 matches
Mail list logo