Dear all,
I am slightly confused about the config of HSRP. More specifically it is the
client default gateway that is confusing me. I have the following config for
redundant Ethernet on Routers 1 / 2:
interface FastEthernet0/1
ip address 10.254.0.1 255.255.255.0
duplex auto
speed auto
By kit I mean questions about the Cisco devices (1200 / 350 / Bridges etc),
and their abilities, specs etc. I had no questions on the CLI at all..
1 cisco wrote in message
news:[EMAIL PROTECTED]
Do you mean cisco interface when talking about the KIT?
Any questions on the cli?
Message
my
AP questions were about 350 series and about 3 or 4 questions on Bridging.
This was just my experience of the test, hope it helps.
Regards,
DW
1 cisco wrote in message
news:[EMAIL PROTECTED]
I am currently studying for my wireless specialization, wondering if
anyone
has taken the new test
Hi all,
I have a 2620 series running IOS (C2600-I-M), Version 12.2(8)T4. I also have
2 x WIC-1T installed. When I do this both of the interfaces show as
interface down / line protocol down. However when I install either interface
on its own (In either slot) they work fine. Is this a limitation of
Hi all,
I have a 2620 series running IOS (C2600-I-M), Version 12.2(8)T4. I also have
2 x WIC-1T installed. When I do this both of the interfaces show as down /
down. However when I install either interface on its own (In either slot)
they work fine. Is this a limitation of the 2600, I cannot find
I have a 3640 router (Pri rate Interface / backup ISDN interfaces) that is
not performing as I thought it would...One of the channelised interfaces
went down yesterday and the backup ISDN for that line kicked in, however I
could no longer ping into the remote site once the backup came up - The
When the primary is up the route table shows:
192.1.1.0/24 is variably subnetted, 2 subnets, 2 masks
S 192.1.1.0/24 is directly connected, Serial0/0:1
C 192.1.1.25/32 is directly connected, Serial0/0:1
When the primary goes down it shows:
192.1.1.0/24 is variably subnetted,
Can I manually change the Flash memory on a 2500 to Read\Write in order to
load an image onto it. It is displaying as Read Only at the moment. I can
load images with the software loader so I am assuming there is a way of
changing the designation.
Sincerely,
DW
Message Posted at:
http
run the test on other configured neworks and they all show consistent
ping response times of up to 32ms, but nothing like what is happening for
this one client.
DW wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
I am running 2 WAN links through the same router and have b
/Max/Avg times fluctuate constantly with one being as bad as
40ms/560ms/75ms.
Robert D. Cluett wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
What type of device?
What layer 2 protocol? PPP or HDLC?
What is the source and destination of the ping?
DW wrote in message
Can anyone help,
I am setting up a WAN link between two sites that will be running Citrix.
There will be quite a lot of TCP/IP print traffic running across the link
and I want to ensure that this does not interfere with the ICA traffic. What
would be the best queuing method to use (If this is
I am running 2 WAN links through the same router and have been have session
disconnect problems recently. I have been running several ping tests across
both of the links (128K FR and 512K Leased line) and they are both showing
response times fluctuating from 30ms to 1400ms (No dropped packets). I
12 matches
Mail list logo
