Look also at the (if used) trunk encapsulation, use ISL prefered else
802.1q, but be sure to use the same at both ends,
Ruud
-Oorspronkelijk bericht-
Van: Chris McCoy [mailto:[EMAIL PROTECTED]]
Verzonden: donderdag 3 augustus 2000 7:33
Aan: David Jones
CC: [EMAIL PROTECTED]
Onderwerp:
It is the multicast address for EIGRP
Ruud
-Oorspronkelijk bericht-
Van: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
Verzonden: zaterdag 29 juli 2000 16:26
Aan: [EMAIL PROTECTED]; [EMAIL PROTECTED]; [EMAIL PROTECTED];
[EMAIL PROTECTED]
Onderwerp: Accesslist/ syslog question?
I have
Title: Trouble with 2501
You
need a new image with the IPX feature set.
Your
image does not include the IPX protocol.
try
IP?
if the
return is only IP then there is no IPX features included
Ruud
-Oorspronkelijk bericht-Van: Anderson, Stuart
[mailto:[EMAIL
There is a default time-out specified, if the IP packet exceeds this it will
cause a time-out (*) of course, if the router has a access-list for ICMP
packets (since trace-route uses ICMP) then you will have a complete time-out
for a hop. (i.e. see 15)
Ruud
-Oorspronkelijk bericht-
Van:
Hi Robert,
I know a Siemens device (called a ULAF) which will convert G.703 to either
X.21 or V.35
It is not managable (as far as I know)ad I also not sure if it is DC
powered.
Ruud
-Oorspronkelijk bericht-
Van: McCallum, Robert [mailto:[EMAIL PROTECTED]]
Verzonden: dinsdag 18 juli
In IP rules it is not possible to use a zero-subnet.
If you wanna overrule this, use it anyway (and why not :-) ) and place a
interface anyway in it you must invoke the ip subnet-zero command.
Try subnetting a IP subnet and without the ip subnet-zero command set an ip
address on a interface in
know that cat5000 will do it for sure... but probab ly not the cheapest
solution?
-Oorspronkelijk bericht-
Van: Nanbo, Kuniaki [mailto:[EMAIL PROTECTED]]
Verzonden: maandag 26 juni 2000 17:52
Aan: Group Study
Onderwerp: L3 switching by 2948G
Hello.
Does Cat2948G(not 2948G-L3) have
yes
there is,
You
must register at the cisco site as a CCNP for that, don't know the URL anymore,
sorry 4 that...
Ruud
-Oorspronkelijk bericht-Van: Nigel Samuel
[mailto:[EMAIL PROTECTED]]Verzonden: donderdag 22 juni 2000
12:40Aan: Cisco Group StudyOnderwerp: cisco
logo
use the ip helper-address command which will translate the broadcast in a
uni-cast address there..
Ruud
-Oorspronkelijk bericht-
Van: NRS Hariharan [mailto:[EMAIL PROTECTED]]
Verzonden: zaterdag 8 juli 2000 18:23
Aan: [EMAIL PROTECTED]
Onderwerp: DHCP Broadcast thru WAN
Hi all,
you cannot upgrade your NVRAM, the / is for dividing your main-/shared
memory, and can be upgraded - 2Mb is factory installed.
Flash mem can be upgraded and is needed if your image exceeds this size.
Note that also your total RAM depends on the software you run, this can be
found on CCO.
Ruud
are you sure about the ring speed?
Ruud
-Oorspronkelijk bericht-
Van: Andrew Lennon [mailto:[EMAIL PROTECTED]]
Verzonden: zaterdag 10 juni 2000 9:05
Aan: 'm. jean stockton'; 'Matt Shell'; [EMAIL PROTECTED]
Onderwerp: RE: Token ring question
knackered media/mau, both router say the
Or try (if the router is not heavily loaded) secondary ip adresses on 1 eth
interface. may be cheaper..
The router will route the 3 subnets, and each subnet wil have it's own
gateway.
Ruud
-Oorspronkelijk bericht-
Van: Apoorva S.Malavia [mailto:[EMAIL PROTECTED]]
Verzonden: vrijdag 7
You may try indeed to configure your int bri0 as you would do normaly, but
if the ISDN line is coming from a PABX it may cause problems there.
If the ISDN interface is not activated it looks dead towards the PABX which
in his side will cause an fatal error and in the worst case disable the
Probably not ;((
if you are using a IRC chat stuff, then the common ip port could be 6667,
you may need to open this one then :)
Ruud
-Oorspronkelijk bericht-
Van: Oladele Ayuba [mailto:[EMAIL PROTECTED]]
Verzonden: zaterdag 8 juli 2000 12:11
Aan: [EMAIL PROTECTED]
Onderwerp: Internet
don't know 4 sure but the FR technique is a point-to-point or multi point
technique.
For each DLCI it is possible to set another subint en choose the p-t-p or
p-t-m stuff.
Why would you wanna do this with HDLC ???
Ruud
-Oorspronkelijk bericht-
Van: Omer [mailto:[EMAIL PROTECTED]]
15 matches
Mail list logo