Hi group,
In Bootstrap protocol, does the PIM router selects the RP with the higest or
lowest IP address (assuming everything else is the same) from the RP-set
list obtained in the RP-discovery message?? I was reading Jeff Doyle's
Routing TCP/IP Vol 2 and pages 491 (first bullet point) and 564
Greetings,
Can I configure the PIX to do both site-to-site and
Remote access VPN at the same time?
I think it is impossible since I can only apply only
one crypto map to the outside interface.
Can someone confirm?
Kim.
__
Do you Yahoo!?
Yahoo!
Greetings,
Can I configure a Cisco PIX firewall to do both
site-to-site and remote access vpn preshares key in
one box?
The reason I asked because after configuring
site-to-site vpn, my remote access vpn stops working.
Kim.
__
Do you Yahoo!?
I am running ios ver 12.1.17 on my 2500 and it
supports TTCP. TTCP also available on MSFC1/MSFC2.
Han.
--- MADMAN wrote:
It's also supported on the 7500 and 7200 series
routers.
Dave
Brad wrote:
I have not been able to find it on ANY platform
other than the 12000 and
1,
__
Do you Yahoo!?
Yahoo! Mail Plus - Powerful. Affordable. Sign up now.
http://mailplus.yahoo.com
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=58907t=58907
--
FAQ, list archives,
r1
|
|
-
| |
| |
r2 r3
In the above configuration, r2 and r3 are configured
with HSRP.
I need to configure iBGP between r1, r2 and R3. Can I
configure neighbor from r1 to r2 and r3 using the
Hi all,
I have an OC-3 155Mbps UBR WAN link between two sites.
When I transfer files between these two sites using
windows explorer or ftp, I only have about 8Mbps.
Sprint told me I need to change the registry:
TcpWindowSize to get better throughput. Have anyone
experienced this before?
Thanks
Looking for a Lab day swap on June 17 at RTP to early
August. Please email me if you are interested.
Kim.
__
Do You Yahoo!?
Yahoo! Health - your guide to health and wellness
http://health.yahoo.com
Message Posted at:
You may want to try exec-timeout 0 0 under line con0
and no exec under line 1 16.
If you console into the 516-CS, it will take 5-10
minutes. It is normal according to Cisco. It take
about 30 sec if you telnet into it instead of using
the console.
Han.
--- [EMAIL PROTECTED] (Timothy Ouellette)
My network has an Internet Border router. The router
has two ISPs connection: UUNET(T3) and SPRINT(T1). We
have a supernet class B: 18x.18x.0.0/16. Can I
configure the router so that only one of the class C
subnet of this supernet for example 18x.18x.1.0/24 to
use the SPRINT link for both inbound
Have anyone successfully installed minicom on Solaris
8? I tried and it failed me when I did: make ; make
install.
Kim.
__
Do You Yahoo!?
Try FREE Yahoo! Mail - the world's greatest free email!
http://mail.yahoo.com/
Message Posted at:
Hi,
Does anyone know where I can find sources to buy
VIC-FXS with good price? I can not find them regularly
on Ebay.
Kim.
__
Do You Yahoo!?
Try FREE Yahoo! Mail - the world's greatest free email!
http://mail.yahoo.com/
Message Posted at:
Nick,
I managed to do some experiment with my home lab. When I ignored the
dialer keyword at the server side, the server end will not treat the
routing updates (ie. sending of routing updates) as interesting. As a
result, the idle timeout (default 120sec) will count down till zero.
Hence, the
Once you solve R1-R4 problem, that should solve R1-R3. On R4, remove the
subi/f 0.1. Just work using the physical interface s0 and turn on
inverse arp like what you have for R3. Also add a map from R4 to R3.
That may help.
Thanks
David
-Original Message-
From: McHugh Randy
Hi group,
What function does the 'dialer' keyword in the 'snapshot server'
command has?? For eg,
snapshot server 5 dialer
As I understand, this keyword is required for snapshot clients to allow
them to dial to servers as only clients dials to servers (Am I right?).
What function it has
Does anyone want to share with me the IPExpert
workbook in DC Metro area? I would like to buy but it
is too much for my budget right now.
Kim.
__
Do You Yahoo!?
Buy the perfect holiday gifts at Yahoo! Shopping.
http://shopping.yahoo.com
From your config, I assume you ping from router 2 to 1 since you only
have dialer map at BRI0 of router 2. I think you are missing this in the
interface config of BRI0 at router 2
ppp pap sent-username ... password .
Hope this helps...
-Original Message-
From: sudhakar
He is teaching at
http://www.netmasterclass.net/Services/Training/training.html
Han.
--- Gus Hussein wrote:
Does any one know Caslow's E-mail or where he
works, he used to teach at
Mentor.
Does anyone know where he working now
Thanks
-
Do
Hi group,
I need some advice on upgrading my 1601, Read from Flash(RFF)
router. It's now running IOS 11.1 on a 4Mb flash card. I have bought a
new 16Mb flash card and loaded IOS 12.1 (size about 10Mb) on my laptop.
Can I swap out the old flash card and insert the new 16Mb and do 'copy
Mark,
Issue the command: clear line . This
will fix the problem.
Han.
--- Mark Rose wrote:
I am trying to get a terminal server working. It was
working several months
ago but when I tried to bring it up today, I get
the message %3 is not an
open connection. I do not have enough
Hi,
I was a bit confused after reading the Ciscopress CCNP Support book and
Caslow's ccie book. Can frame-relay multipoint sub-interfaces support
inverse arp DLCI mappings?? Ciscopress Support book seem to say no (not
directly though) but Caslow's book says yes. Thanks in advance...
David
Hi group,
I am new to this group. Wondering whether someone could help..
I have two routers (2621 and 1601) tied back-to-back using V.35 serial.
Can I simulate a 64K link with this config if I execute bandwidth
64000 at the interface prompt?? What I understand is that this command
is
Have anyone successfully configured the Cisco VPN 3030
concentrator to work with Cisco ACS TACACS+ for
Administration anthentication?
Kim.
__
Do You Yahoo!?
Spot the hottest trends in music, movies, and more.
http://buzz.yahoo.com/
Message
Below is my company Internet connecttion.
+--++--+
| UUNet router |+ Verizon router +
+--++--+
| ||
Hssi0S0 S1
\ //
Hi everyone,
I have a fractional T3 for Internet connection in my
company. I am implementing VPN for user remote
access with Cisco VPN 3030. I think I have a problem
with my FT3 bandwidth ultilization because the
remote user VPN sessions are dropping off at some peak
time during the day. Is
Hi everyone,
Simple ATM configuration question.
I need to use Map-list and Map-group to configure ATM
Multipoint
I DO NOT need to use them to configure ATM Point to
Point?
Am I correct?
Kim.
__
Do You Yahoo!?
Yahoo! Auctions - buy the things you
To the ATM guru,
I have a ATM WAN via SPRINT from the HQ (Chicago) to 4
regional branch office (LA, FL, NY and CO).
The PVC infomations that SPRINT provides to me after
the circuit installation completed has only the
Originating VPI and Terminating VPI. There are no
information about the VCI.
Have anyone experience with Wireless technology for
backup link solution? I have 2 cities: NY city and LA
connected via T1 point to point and looking for a
backup solution that does not cost too much. Is
wireless is a good solution for this backup?
Thanks!
Kim.
I have a switches internetwork with:
S1 S2
C1 C2
D1 D2
A1 A2
S= server farm switch (Routing with MSFC)
C= Core switch (Layer 2 only)
D= Distribution switch (Routing with MSFC)
A= Access switch
A1 (is VLAN2) is connected to both D1 and D2.
A2 (is VLAN3) is connected
Everyone,
I currently have two T-1's to ISP1 and a Fractional T3
to ISP2. I am using static and default routes to
connect them to the internet. There is no automaticaly
fail-over as you know. Therefore, I am changing our
ISPs but keep the BW the same. Two T1's to ISP1 and
FT3 to ISP2 and I would
I have a MS Terminal server (Port 3389) inside a
private subnet. I am using NAT from the router. I am
using a Static NAT access list:
ip nat inside source static tcp 192.168.1.25 3389
200.200.200.1 3389
I still can not access to the terminal server from the
Internet. Can some one tell me what I
Have anyone experienced this:
I issued a SET SPAN VLANxxx 5/1 and all a suddden, all
of my interface VLANs on my MSFC was brought down and
went back up right away but users noticed a delay when
they was flapped. Can anyone explain what happened?
Kim.
I am trying to upgrade my Catalyst 6509 MFSC to
version 12.1.5. When I issued the cmd:
copy tftp flash at the router prompt. It failed and
told me that there are not enough space to upgrade the
new image. Can someone help me with this. I am digging
cisco web site for reading right now. Sorry this
How do I erase the current flash. The erase flash cmd
does not work on the Catalyst 6500. Do I need to
switch to ROMMON to erase the current IOS and upgrade
the new IOS from there?
Kim.
--- VOIP 2000 wrote:
Kim,
You have to delete the old IOS and make sure you
have enough Flash
Hi everyone,
I feel very stupid to ask this question but I can not
find any documentations that show me how to upgrade my
Catalyst 6509 MSFC IOS to 12.1.x. I know how to
upgrade the CatOS on the SUP1A but not the IOS for the
MSFC. Can someone help me?
Thanks.
Kim.
I have a problem with all of my Windows 2000 servers
failed to authenticate into the PDC which is running
Windows NT 4.0 server. The Apps people are saying that
it is the Switches Network that I have. I checked all
of my switches and routers, I can not find of any ACL
or filter that cause their
Hi Everyone,
Have anyone experienced with Wireless T1 WAN using as
a backup link? Please shed me some light or give me
your comment.
Thanks in advance.
Kim.
__
Do You Yahoo!?
Get email at your own domain with Yahoo! Mail.
I have a few questions about the ATM. Hopefully, you
will clear me up on something that I am not so sure.
I am tasked with upgrading my company current T1 WAN
to ATM DS-3 to 7 regional cities in the US. The HQ is
in Chicago. Currently, the requirement is only use
these DS-3 for Data. In the
38 matches
Mail list logo