That is good news.
Like I said a week ago. Porta Power and a button
jack and that thing will get off in a few minutes
Oh my
(even if you miss a set screw). :)
Cheers, Russ
At 04:46 PM 6/5/2020, you wrote:
Well, 3 days of absence allowed the PB Blaster
to work, cause when I went
Excellent!Sent from Samsung tablet.
null___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want to support the list - use PayPal
to send contribution --
Well, 3 days of absence allowed the PB Blaster to work, cause when I went
to the boat today I swear I could see a tiny hairline area where the shaft
had pulled out of the coupling. Each go round of the bolts and I got a few
more flats each and beat on it with a hammer. Pretty soon I was getting
both equally looks like it might make
them bind more.
Michael Brown
Windburn
C 30-1
From: Doug Mountjoy
To: "cnc-list@cnc-list.com"
Sent: 6/1/2020 11:50 AM
Subject: Re: Stus-List Shaft coupler removal
I would give it a try. I have never used Mapp gas. You
I would give it a try. I have never used Mapp gas. You will want to use as
hot of flame as possible.
On Mon, Jun 1, 2020 at 8:21 AM Josh Muckley via CnC-List <
cnc-list@cnc-list.com> wrote:
> You think Map gas will be good enough?
>
> On Mon, Jun 1, 2020, 11:17 Doug Mountjoy via CnC-List <
>
You think Map gas will be good enough?
On Mon, Jun 1, 2020, 11:17 Doug Mountjoy via CnC-List
wrote:
> Josh,
> I used to work in a machine shop where I had to remove gears off of
> shafts. We used an acetylene torch to heat the gear fast, so the shaft
> didn't expand as fast. Using a slow heat
Josh, I used to work in a machine shop where I had to remove gears off of
shafts. We used an acetylene torch to heat the gear fast, so the shaft didn't
expand as fast. Using a slow heat source will heat the coupling and shaft at
about the same rate. You want to expand the coupling faster than
I used a cutting wheel and cut a groove longitudinally down one side being
careful not to score the shaft. Then a few surgical strikes in the groove with
a cold chisel to slightly spread the coupling. Then it slid right off. About a
half an hour minus setup.
Of rick bushie via
CnC-List
Sent: Monday, June 1, 2020 8:01 AM
To: cnc-list@cnc-list.com
Cc: rick bushie
Subject: Re: Stus-List Shaft coupler removal
Josh, I had to cut mine off. Luckily, a ready replacement was available from
Moyer Marine for my A4.
Rick Bushie
Anchovy
1971 30-1
Sent from my iPhone
Cut the coupler parallel to the shaft using an angle grinder with a cut-off
wheel. Try to cut into the key so yuh don’t damage the shaft. I didn’t have
enough room to get all the way among the coupler with the grinder so I used a
multi tool to finish the cut. Then pound a cold chisel into the
Hi Josh,
I had a bear of a coupling removal last fall on the project boat.
We did all the usual things first (heat, bolts
with strongback & socket, swearing, more swearing
& sweating). Lots of peering at it with lights and a mirror too.
Anyhow, got a Porta-Power rig from work with a
List
Cc: Josh Muckley
Subject: Re: Stus-List Shaft coupler removal
How difficult was cutting it off?
On Mon, Jun 1, 2020, 08:02 rick bushie via CnC-List
mailto:cnc-list@cnc-list.com>> wrote:
Josh, I had to cut mine off. Luckily, a ready replacement was available from
Moyer Marine for
How difficult was cutting it off?
On Mon, Jun 1, 2020, 08:02 rick bushie via CnC-List
wrote:
> Josh, I had to cut mine off. Luckily, a ready replacement was available
> from Moyer Marine for my A4.
>
> Rick Bushie
> Anchovy
> 1971 30-1
>
> Sent from my iPhone
>
>
>
Josh, I had to cut mine off. Luckily, a ready replacement was available from
Moyer Marine for my A4.
Rick Bushie
Anchovy
1971 30-1
Sent from my iPhone
___
Thanks everyone for supporting this list with your contributions. Each and
every one is
I think I could use a torch safely. I have ideas for that...
On Mon, Jun 1, 2020, 05:45 Graham Collins via CnC-List <
cnc-list@cnc-list.com> wrote:
> Heat. You don't want to use flame, I get that. How about laying a BBQ
> charcoal lighter on it? You could probably bend the thing to make more
Heat. You don't want to use flame, I get that. How about laying a BBQ
charcoal lighter on it? You could probably bend the thing to make more
contact.
Graham Collins
Secret Plans
C 35-III #11
On 2020-06-01 3:34 a.m., Josh Muckley via CnC-List wrote:
Getting the shaft out of the coupler is
Getting the shaft out of the coupler is turning out to be quite a trick.
I'm using a large socket in the center of the coupler to act as a spacer.
Then I'm using the coupler bolts to act as clamps and draw tights against
the socket. I have lots of penetrating oil in just about every location
17 matches
Mail list logo
