Hello all,
I have had inquiries about the modes of operation for this special
event. I will operate ssb, but at the top of each hour of operation I
will switch over to cw for those K2's that don't have the ssb option and
for those with K1s or KX1s. Here are the frequencies that I will hang
aroun
Original post:
I'm feeling dumber than a rock here, but in following instructions on
alignment of filters using spectrogram I am trying to find how to
turn off
AFIL (and/or SSB?) so that alignment is accurate... What is the
order in the
menu for turning it/them off? Can someone please tell me ea
Hi Don, thanks for responding,
Short coax cable between K2 Ant > Txin IF1
Antenna is connected to transverter Ant plug.
Control cable is connected between K2 and transverter
SSB on 6 meter works fine so cables are ok. Keyer is working fine on HF
bands.
Relay is clicking in the transverter when
I know this is a stupid question...but sometimes the easiest things can go
wrong.
Do you have the rig in CW mode or did you forget and you're still in SSB
mode??? You'll hear relays click in the K2 but there will be no power out
because you're keying the rig in SSB mode with no audio.
Like
Hello Gregg,
in my original e-mail is explained I was using the internal keyer so yes it
was in the cw mode otherwise the keyer doesn't work.
Original case:
I have a K2/100 with a 6 meter transverter. I tried to use it last night in
CW and noticed than on CW the K2 PTT relais is switching and th
Rob,
Assuming you have all the K2 trn 1 menu parameters set correctly and the
transverter properly configured (and you likely have them correct or the
transverter would not work in SSB mode), you have a mystery for me. The
Transverter does not know (and should not know) whether the RF is being
pr
Hello all,
I just updated the website to include some pictures of the covered
bridges I'll activate during the ARCBS Covered Bridge Weekend. If you're
interested, click on the link.
http://www.wa3wsj.com/files/WitnessPage.html
72/73,
Ed, WA3WSJ
___
TRN1 option is set to On and I can see when setting TRN1 to off the 6 meter
transverter switches off and 6 meter is not a selectable band anymore.
Tried 10 meter CW and gives 100 watt output, no problem.
CW is not in test mode but in oper mode
Tried CW keyer in hand mode and dash side of keyer p
My K2's (#3104) RX is quiet on start-up on an intermitent basis. It's the
same sound that one hears when the AGC kicks in, but it seems "stuck". To
get it going, I tap AGC and it springs to life. This usually occurs when I
first turn it on during the day. Subsequent on/off's during the day a
Rob,
I have a K2 (no KPA100) with KIO2, K60XV and XV50 and CW works fine on
6 meters. My 28Mhz band feeds 1 milliwatt through the K60XV to the
transverter; the PTT feeds through the KIO2, same as your setup.
Your jumpers should be set to include the attenuator (JP3 2&3, JP4
2&3) and to exclude t
Rob,
Just as another wild guess - I need to ask if the IF frequency you are
attempting to transmit on is lower than 28 MHz? (i.e. are you attempting to
transmit CW below 50 MHz?) If so, that would place the signal outside the
ham band and the K2 may have no output at that frequency (the firmware
I'm in the process of installing my KIO2. It does not work. I checked
and re-checked all the wiring, location of the components, etc and
everything looks good.
My K2 has the Rev A control board so I had to cut the trace and solder
some wires (that's the one thing I haven't double-checked yet).
12 matches
Mail list logo
