I too would like to see what settings are being used for NR as I seem to get a
large decrease in Audio volume when NR is engaged.
I hope those having success with the new NR can enlighten the rest of us...:-)
Gary
VK4WT/P
Sent via BlackBerry® from Telstra
Just want to inform other builders that I'm currently starting to bring K1 SN
002761 alive, no questions so far.
I will check the mail regurlarly, and if helpfull share my experience.
Currently I'm close to finalizing the filter board.
73
PE1FJN
QTH: Zwolle, The Netherlands
JO32BL
Marc
Gary,Jim and Robin,I am pretty satisfied with 3.27 NR and I will answer all
your questions off the group and also I will send you guys a MP3's for CW and
SSB showing how well my K3 works when engaged the NR but right now I a not at
home,I am at my work office,tonight when I be back I will
Benny Aumala-2 wrote:
Thank you, Dick
Programming was not what I intended to learn.
Now the quickest way goes like this:
=Open Elecraft K3 Utility
=open Edit / Command tester Macros
=Type for Macro 1 - Text to send - pc005; (do not forget semicolon)
=Type for Macro 2 - Text to send
I've read all the messages I could find posted about the P3 while I was away,
and one question that doesn't seem to have been asked is: will it be
available in modular kit form like the K3 or only ready built?
-
Julian, G4ILO. K2 #392 K3 #222.
* G4ILO's Shack - http://www.g4ilo.com
* KComm
I was interested to read in the discussion about the ADAT transceiver that it
used adaptive predistortion to improve the linearity of the TX. As the K3 is
also an SDT could this be a future enhancement?
-
Julian, G4ILO. K2 #392 K3 #222.
* G4ILO's Shack - http://www.g4ilo.com
* KComm -
The K2 NB works very well with light-dimmer noise. If you have a
light-dimmer to test it the results should be dramatic.
73,
Drew
AF2Z
On Thu, 27 Aug 2009 13:20:22 -0700 (PDT), Eric WD6DB(lost in noise)
wrote:
I built my K2 some months back with the KNB2 option. The noise blanker has
never
David,
I cannot fully answer your questions right now, BUT I must give you a
caution. The K2 AUX IO connector is *not* an RS-232 port - that is why
it is labeled AUX IO.
To avoid damage to your K2, use ONLY the cable shown in the KIO2 manual
to connect your K2 to the Rigblaster Pro.
In other
I agree with Gary, it would be helpful if the settings that are proving
useful for some could be shared with all of us. Thanks, I am learning from
this thread prior to installing the software update and then installing the
sub rx. This forum is most helpful and one of the many reasons my K3
Joe Planisky wrote:
Some times you can't satisfy all the people all the time with one
road.
Truer words were never spoken!
I'm a full time CW operator (well, 99.9% CW, 0.1% digital modes.) I
played with the pre-3.25 NR quite a bit and I was never able to find a
setting that made a
Hector
I think a lot of folks would be interested in your findings and those of
others, so, you would do us all a favour if you could put those answers and
clips in a place we can all view: perhaps the Elecraft site?
David
G3UNA
Gary,Jim and Robin,I am pretty satisfied with 3.27 NR and I
I'm still playing with the 3.27 NR, but I like it alot. I operate CW
only and have been using the F1-x filter section mostly because it
seems that F2 through F4 are minor variations on the F1 theme, so to
speak; but I will try them later. With CW signals of course there is
not as much subtlety
I'm hopeful it will be in kit form. If it costs more than an SDR-IQ, I will
have second thoughts about getting one,
Julian, G4ILO wrote:
I've read all the messages I could find posted about the P3 while I was
away, and one question that doesn't seem to have been asked is: will it be
Both. :-)
73, Eric
Julian, G4ILO wrote:
I've read all the messages I could find posted about the P3 while I was away,
and one question that doesn't seem to have been asked is: will it be
available in modular kit form like the K3 or only ready built?
I must be getting old...
I can't find a picture of the P3 anywhere...
--
Dave G. KK7SS Richland, WA
'06 Honda Civic Hybrid
'65 MK III A-H Sprite
'76 MKIV 1500 Midget
If I wake up in the morning, and I hurt, it means that I'm still
alive !!
Here are links to the P3 and K3 with the P3 in full spectrum display mode.
(Note that our text fonts are now larger than that shown and are very
easy to read. We will have selectable font sizes on the release version
of P3.)
Thank you, Eric...
A gentleman. as always ;-))
--
Dave G. KK7SS Richland, WA
'06 Honda Civic Hybrid
'65 MK III A-H Sprite
'76 MKIV 1500 Midget
If I wake up in the morning, and I hurt, it means that I'm still
alive !!
__
For those of you that noticed the unexpected increase in low end bass
response in the last release, and then its removal in the current
release, stay tuned. We are properly including it in in the next beta
release.
In the prior beta test release it was an unexpected bug/side effect that
only
You mean, those *really* arent the Droids I was looking for,
Obi Won?
:)
-lu-
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
Thank goodness for bugs!
I wonder if anyone understands why the bass was cut off in the first place?
BTW: NR seems to work really well for CW now. It's actually helping the copy
of the weak ones. 73
Steve
N4LQ
n...@carolina.rr.com
- Original Message -
From: Eric Swartz - WA6HHQ, Elecraft
On Fri, 28 Aug 2009 09:58:00 -0700, Eric Swartz - WA6HHQ, Elecraft
e...@elecraft.com wrote:
For those of you that noticed the unexpected increase in low end bass
response in the last release, and then its removal in the current
release, stay tuned. We are properly including it in in the next
Yo! Put the rig in the Civic with a 500W (audio) amp, an 18 woofer
and some Monster cables, tune it down to 50 Hz, and all my homies can
be DX'in me from 5 blocks away.
On Aug 28, 2009, at 9:58 AM, Eric Swartz - WA6HHQ, Elecraft wrote:
For those of you that noticed the unexpected increase
Excellent!
Will the P3 case be available for purchase, on its own, with blank front and
rear panels, for home constructed accessories?
Eric Swartz -WA6HHQ, Elecraft wrote:
Both. :-)
73, Eric
-
Julian, G4ILO. K2 #392 K3 #222.
* G4ILO's Shack - http://www.g4ilo.com
* KComm -
This is strange...
A lot of people (including me) have noticed and pointed out K3's initial
lack of LF response compared to other sets. Also, a lot of energy has been
put into finding causesremedies both by users and developers.
Now *a solution* is presented as a pleasant coincedental
Please select one:
Option 1 - Those who would like a little extra low end audio frequency
available, a little extra headroom over the 100w limit when necessary, and
those would like to be able to transmit AM/FM and ESSB through their wide
roofing filter.
Option 2 - Those that would prefer
Not at this time. Possibly later is there is a large demand.
73, Eric
Julian, G4ILO wrote:
Excellent!
Will the P3 case be available for purchase, on its own, with blank front and
rear panels, for home constructed accessories?
I'd purchase a pair of P3 blank cases for speakers.
Perhaps Elecraft will produce an S3 speaker in
the P3 case ... with the logo, of course.
73! Ken Kopp - K0PP
elecraftcov...@rfwavwe.net
http://tinyurl.com/7lm3m5
__
Elecraft
I loaded the new firmware and the DSP is 2.24, the web site show 2.25.
The FW is 3.27.
I hope I did not miss this mentioned already.
Rich
K3RWN
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
I haven't seen it mentioned, but I'm seeing the same thing.
73,
Ken K3IU
~~
bearcat wrote:
I loaded the new firmware and the DSP is 2.24, the web site show 2.25.
The FW is 3.27.
I hope I did not miss this mentioned already.
I just checked. The current .zip in the beta directory has 2.25. We made
a minor change in DSP 2.25 to fix a rare case of DSP instability in NR
when AGC was cycled off and on.
73, Eric
bearcat wrote:
I loaded the new firmware and the DSP is 2.24, the web site show 2.25.
The FW is 3.27.
I would also purchase a case, when availiable.
Philip LaMarche
LaMarche Enterprises, Inc.
www.instantgourmetspices.com
www.w9dvm.com
800-395-7795 pin 02
727-944-3226
FAX 727-937-8834
NASFT 30210
K3 #1605
CCA 98 00827
CRA 1701
W9DVM
-Original Message-
From:
I have 3.27 FW, the latest. So you can change the resoltion to .1.
When I go into the menu and try, it just states n/a. Any ideas?
Karl N6XVT
Sent from my iPhone
__
Elecraft mailing list
Home:
I finally found the cause of my inability to align the band filter in my
K1 under construction. I installed the RF board U2 backwards :-[ . I've
managed to suck the solder from the holes on the bottom of the board,
but still have some on the top. I'm trying to salvage the IC (product
detector)
Hello List and Robin,
Robin asked for some of my settings that I use on my K3 regarding the
new NR in Firmware 3.27, and I thought that it may help the Group to
post them here.
These are answers to Robins questions, so keep this in mind.
AND...I use my K3 almost 100% as an IF for VHF Bands,
Yeah, I agree with what you are saying. I like the NB on CW, but on SSB
even at F1-1 it sounds somewhat like being in a tunnel. I would like to see
a NB setting that is less aggressive and that doesn't change the audio as
much.
Also it would be nice if the audio didn't reduce in volume when
but still have some on the top. I'm trying to salvage the IC (product
detector) so am begging for advice on how to successfully free up the
solder from the top of the board. This is an 8 pin DIP.
You run the risk of damaging PCB pads if you try to extract it all at once.
It might be worth
Thanks to all that replied on and off list. I've tried a wick and the RS
solder sucker and have the bottom clean and clear but there is still
just a bit but enough solder on the top of the board to hold the IC in
place. Think I'll go the safe route and order a replacement from
Elecraft and
Got to love the color too!
73,
Bill
K9YEQ
K2 #35; KX1 #35; K3 #1744; mini mods
ATS-3B
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Eric Swartz - WA6HHQ,
Elecraft
Sent: Friday, August 28, 2009 11:44 AM
To:
Thanks, I'll try it.
Karl. N6XVT
Sent from my iPhone
On Aug 28, 2009, at 2:43 PM, Ron W3ZV w...@verizon.net wrote:
I got bit by the same thing. Need to be in CW or DATA. Not available
in SSB.
Ron W3ZV
Karl Marderian wrote:
I have 3.27 FW, the latest. So you can change the resoltion
Looking for a Elecraft MH2 mic for my K2, please email off line to
k...@yahoo.com with price/condition shipped to 75163.
73
Paul
--
View this message in context:
http://n2.nabble.com/WTB-MH2-mic-for-K2-tp3539005p3539005.html
Sent from the [K2] mailing list archive at Nabble.com.
I changed my audio equalizer from where it was and that makes a huge
difference for me. I tried to remove some of the noise with the equalizer
and that caused the sound to be very hollow.
73,
Bill
K9YEQ
K2 #35; KX1 #35; K3 #1744; mini mods
ATS-3B
-Original Message-
From:
I'm running version 3.27/2.25 on K3 #384. I live in a high noise suburb of
NYC. When I tap the NR button, the noise just about disappears, and the
signal remains, SSB or CW. Magic!
The difference is more noticeable on SSB, of course, because I usually have
the pass band set to 500 Hz for
Gary,
Good decision.
Just think of it this way - even if it costs $25 to $30 to order one (or
2 or 3) from an electronics distributor like DigiKey or Mouser or
others, that is a small price compared to the price of a board and the
rest of the components that are mounted on it. In this
Tony,
Did you mean NR when you stated NB? I find no audio reduction when
turning on the NB unless I have the IF NB cranked up to maximum.
I first thought the new NR was reducing the audio, but I found it was
not so when one is tuned to a signal. The noise reduction is so
effective that in my
There are no bugs!
Merely undocumented features ;)
David Wilburn
NM4M
Sent from my Verizon Wireless BlackBerry
-Original Message-
From: pd0psb p.s.bijp...@gmail.com
Date: Fri, 28 Aug 2009 14:02:08
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 -extended- low end Bass
Just finished my KX1. Unfortunately, it won't produce any output on
transmit. Receive is excellent. Toroids are solid. Board was carefully
inspected with good magnifier. All solder joints are solid and clean.
I get the following voltages in tun mode:
Q6: B=0v C=12.67v E=0v
Q5: C=12.67v
On Fri, 2009-08-28 at 14:51 -0700, Gary W. Marklund wrote:
I finally found the cause of my inability to align the band filter in my
K1 under construction. I installed the RF board U2 backwards :-[ . I've
managed to suck the solder from the holes on the bottom of the board,
but still have
I agree with N6MQL, after working with 3.27 awhile now, 3.25 made CW better.
I only have the 250Hz filter, and it doesn't do as well with NR as wide
settings... and the wide filter setting makes the NR shine. It may even work
better than 3.25 NR narrow overall, I don't know.
My constant
Doug,
Except for the voltages on Q4, the DC voltages look OK. Check R9 and
R26. The voltage at both ends of R26 should be near 6 volts.
Did you put the jumper between J7 pins 1 and 3?
How do the toroid leads look? Well stripped and tinned with a bit of
tinned lead showing on the toroid side
~
N2CQ QRP CONTEST CALENDAR
September 2009
~
SLOVENIA CONTEST CLUB RTTY Championship .. 100W Category
Aug 29, 1200z to Aug 30, 1159z
Rules:
I am confused on the X1 Crystal, cylindrical 32.768 crystal. I have two. One
is labeled S573 and the other is labeled S793. I don't think there are
supposed to be two and I am not familiar with these. I gues the 793 is closest
to the 32.768 but some advice would be nice or am I overlooking
Ivan,
I don't know if there is a significant difference between the 2 crystals
or not, but I suspect that either will work.
The crystal is only for the Real Time Clock. Put one crystal in and
keep tabs on the time display for a few days. If it is off drastically,
try the other crystal. If
How does one test this without a calibrated signal source?
Why was 80M chosen for the test frequency? Most ops have preamp off and
many have attenuation in.
It appears one needs something like an 80db over S9 sig for it to cut in.
73 de Brian/K3KO
No virus found in this outgoing message.
There are others like myself who may be interested in your answers.
Bud, K9ZT
Original Message
Subject:Re: [Elecraft] NR for Dummys
Date: Fri, 28 Aug 2009 04:07:30 -0700 (PDT)
From: Hector Padron ad4c2...@yahoo.com
To: elecraft@mailman.qth.net
Gary,Jim and
54 matches
Mail list logo