I have both DXLab and the MK2R+ set up per the documentation in both. Yet,
the MK2R+ busy light indicating two radios on same band comes on constantly.
The second radio is never turned on, yet the problem occurs constantly.
Cycling power on the MK2R+ solves the problem for a few minutes - any QSY o
I have taken it up with both on the DXLab reflector. Dave said he can't
investigate SO2R box issues and I understand that. Joe referred me to the
documentation for MK2R+ with DXLabs and I changed all settings to that
document, problem still occurs. I sent Joe some log files but no solution.
John K
Is the KAT500 hefty enough such that the KPA500 can be placed on top of it?
That is the way I'd like to stack/arrange the two in my station.
Phil - AD5X
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
He
I was kind of hoping it would be in a small box with the same height like
the k3, P3, & KPA500 so they could all be lined up in uniform together but I
see that won't happen. That would really look nice.
Jim KE4WY
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-
The KTA500 Advance Order Form does NOT exist, but I suspect the title of this
message attracts some interest. Is Elecraft ready to post an Advance order
Form for the KAT500 as was the case with the KX3? Thank you, and please
e-mail me the first KAT500 Advance Order Form in gratitude for my
suggesti
Using microHAM 2R+ - DXLab - N1MM combo with 2 K3s and the setup works
exactly like Joe describes it.
No problems.
Larry/K2GN - http://k2gn.com
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of John K3TN
Sent: Saturday, Mar
Isn't the KIO included? I do plan to hook up to the PC also to the
sound for psk, DRM and SSTV
In the future the transverter adapter is probably one of the earlier
add-ons for the RX antenna and then some additional filters.then
later the sub receiver. more.
not sure if I need th
Yes, the KIO3 board is a part of the basic K3. You do not need to include it
with your order, nor is it even an option on the order page.
73,
Bruce, N1RX
> Isn't the KIO included? I do plan to hook up to the PC also to the
> sound for psk, DRM and SSTV
As I recall, you are not configuring the Commander portion of DXLab
Suite correctly - specifically, you are not configuring the radios
(K3 and TS-2000) individually on separate ports with Commander's
"Multi-Radio" tab and selecting radios with the radio buttons on
Commander's primary screen.
Howe
Larry,
There are possible reasons why one station works and another does not, and
there seems to be little that can be done about it without knowing specific PC
hardware being used and what other software might be in use.
Matthew Pitts
N8OHU
___
I have been noticing that sometimes if I cycle through the modes on the K3 from
USB back through to USB (including cw, data, AM, FM and back to USB) or turn on
either Power SDR or Na3p my filter settings change and sometimes considerably.
This can happen if I stay within the same band or when I
Every K3 includes the KIO3 I/O interface that provides connectivity to a PC.
Every K3 owner needs this to install firmware. It's standard.
The K2 (not K3) has an optional KIO2 interface. Perhaps that's the source of
the confusion.
73 de Dick, K6KR
-Original Message-
From: elecraft-boun.
Takes too much deskspace, Jim.
As Eric or Wayne noted a few weeks ago it was designed to sit on top of the
KPA500 (or K3 for that matter, same footprint). Ventilation will be no
problem with this positioning, they took care of that.
Vy 73, Olli - DH8BQA
http://www.dh8bqa.de
- Original M
Ron,
there was no advance order form for the KX3. You could only subscribe to an
info mailing list where the link to order was posted first (and copied to
the main Elecraft reflector just a minute later).
Vy 73, Olli - DH8BQA
http://www.dh8bqa.de/
- Original Message -
From: "KM4VX"
Thank you to all who helped (and offered to help) my group of six Boy Scouts
complete their first amateur radio QSOs this morning on 20 Meters, and earn
their Radio merit badge in the process. Each was able to overcome mic fright
and were thrilled when they received responses to their CQs from M
Unfortunately, NaP3 sets filter widths (high/low cut) on the K3
when changing modes rather than simply follow the values as set
on the K3.
There is nothing that can be done about that unless the author of
NaP3 provides an option to *not* set filter (high/Low cut) on the
K3 and simply follow (disp
Joe,
Thanks for answering my question so quickly. So even though this is annoying it
is normal and not a malfunction of the K3.
Thanks,
Keith
AG6AZ
Sent from my iPhone please excuse typos
On Mar 31, 2012, at 7:37 AM, "Joe Subich, W4TV" wrote:
>
> Unfortunately, NaP3 sets filter widths (hig
On Fri, Mar 30, 2012 at 6:42 PM, Steve KC8QVO wrote:
> I know what you're saying. I ordered later on the second day (12/28).
> Steve, KC8QVO
>
>
> Hi Steve, Since you ordered early I would expect you to be wearing the KX3
at the HFPack net in Dayton this year instead of the Kenwood TS-2000 the
fi
On Sat, Mar 31, 2012 at 9:37 AM, Joe Subich, W4TV wrote:
>
> Unfortunately, NaP3 sets filter widths (high/low cut) on the K3
=
Keith, did you turn off "Poll Filter Width" on the front page of NaP3 setup?
Tony KT0NY
__
Elecraf
Tony,
I will need to check that setting again but I thought I did. When I get down
to the shack I will check first thing.
Keith
AG6AZ
Sent from my iPhone please excuse typos
On Mar 31, 2012, at 7:57 AM, "Tony Estep" wrote:
> On Sat, Mar 31, 2012 at 9:37 AM, Joe Subich, W4TV wrote:
>>
>> U
Keith,
I think you'll find that it is NaP3 that is doing this. NaP3 has default
filter settings for each mode and restores those filter settings every
time you change modes. This happens regardless of whether the mode
change is initiated from NaP3, from the radio, or from other control
softwar
Bravo, Mark! Well done and Congrats to you and the lads.
73, Bert
"...and all the pieces matter."
-- Det. Lester Freamon, BPD
Sent from my Verizon Wireless 4GLTE smartphone
- Reply message -
From: "Mark Volstad"
To:
Subject: [Elecraft] Boy Scouts need your help [than
All I can say is Thank you Elecraft Forum for being so helpful.
I was on another forum and asked for help and was bombarded with personal
emails like "I had to figure it out so you need to also."
Not a friendly place for a new to digital user.
Here is my question about the K3 rig.
I have to s
You will have to turn off CAT Polling for both "Filter Width" and
"Filter Shift" in the NaP3 Setup. Doing this stops NaP3 from changing
the filter settings on mode changes, but it also disables filter control
from NaP3, and (understandably, since polling is disabled) the filter
display on the N
GM Keith: Notwithstanding Joe's comments related to Na3p, I've noticed a K3
software "memory" problem which may or may not be related.
There seems to be two instances of when the K3 appears to "loose its mind".
(BTW its s/n 2432 using 4.47 and 2.73 FW.)
1st is when I've set up the Norm I and I
The weekly Elecraft SSB net will meet tomorrow (4/1) at 1800Z on 14.3035MHz.
Dale, WC7S, will be the net control station from WY. I'll be back next
week. Enjoy.
73,
Phil, NS7P
__
Elecraft mailing list
Home: http://mailman.qth.net/mail
>From one BSA Radio Merit Badge Counselor to another, keep up the good work!
... And sorry for missing the opportunity!
73,
Mike, N0SO
BSA Merit Badge Counselor for:
Backpacking, Electricity, Electronics and Radio
PS: If you get the opportunity to backpack at the Philmont Scout Ranch, carry
a
Sorry for misleading anyone about the KIO board. It was late Hi!
I got both my K3's without the TCXO option and you will notice some
drift until the rig warms up. I broke down and got the TCXO options for
both. I am happy I did.
Good luck with the K3 you will love it!
Mike W0MU
W0MU-1 CC
I think the KAT500 may be sturdy enough for the KPA500 to sit on top of it,
but I am a bit nervous about interrupting the air flow around the amp. I
think, during my recent discussion with Eric, he suggested it be set on, or
under, the K3. Airflow is important there too, but not as critical pe
I've wonderedand asked this question before but never saw a response.
Can anyone answer this one?? Will the KAT500 be a solder kit,
bolt together kit, or assembled??
73...de...Fred N9TA
>My apologies if this has been asked/
The KPA500 draws in air from the top, and exhausts it out the back. So
placing the KAT500 under the amplifier shouldn't affect KPA500 air flow.
Phil - AD5X
"I think the KAT500 may be sturdy enough for the KPA500 to sit on top of it,
but I am a bit nervous about interrupting the air flow around
On Sat, Mar 31, 2012 at 10:28 AM, Richard Ferch wrote:
> You will have to turn off CAT Polling for both "Filter Width" and
> "Filter Shift" in the NaP3 Setup. Doing this stops NaP3 from changing
> the filter settings on mode changes, but it also disables filter control
> from NaP3...
===
Y
FWIW, I had some goofy things happening like this during a contest. I was
having trouble tuning my antenna and thought it was just due to ice on it.
After the contest was over, I looked out the window to find part of my loop was
laying in the snow.
That was causing RF in the shack. I no longe
Good to know, as I'm betting that the KAT500 is not going to weigh nearly as
much as the KPA500! Placing it on top of the amp, with three fat RG-8 cables
hanging out the back of it would (IMHO) tend to make the tuner susceptible to
tipping backwards. Locating it under the K3 is not an option at
You can change the filter centre frequency in any mode by using the
SHIFT control. Tapping this control will switch between SHIFT/WIDTH and
LO/HI CUT modes, and will also briefly display the current FC or LO
setting in the VFO B display. The default or "normal" FC is marked with
an asterisk (*)
> The default filter centre frequencies in CW and in AFSK A/FSK D can be
> adjusted using the K3's PITCH control.
More specifically, one can adjust the default CW offset and the AFSK A
or FSK D *Mark* frequency. using the "Pitch" control. CW pitch is the
center of the filter but AFSK A/FSK D p
> What is really needed is a way to disable the automated filter control
> that takes place on mode changes but without disabling polling and
> manual control of filter settings.
This is the key - NaP3 should be able to *read* the K3 filter settings
without changing the filter settings. Readi
Modular kit like the K3 and KPA500.
73,
Eric
www.elecraft.com
_..._
On Mar 31, 2012, at 9:05 AM, "Fred Bennett N9TA" wrote:
> I've wonderedand asked this question before but never saw a response.
>
> Can anyone answer this one?? Will the KAT500 be a solder kit,
>
> bolt together kit
There should be no interaction issues between the KAT500 and the KPA500 when
the KAT is under the amp. We also beefed up the KAT500 cabinet to handle the
weight of the KPA500.
Also, placing it on top of the amp does not raise amp PA transistor temp
significantly for most casual duty cycle use,
I hope there is a wish list for the P-3 Utility. It really eases the process of
upgrading firmware, etc.
Please add:
- "Save P3 Configuration"
- "Reload P3 Configuration"
This would be the same feature set as in the K3 Utility.
Thanks for the great little utility!
Jack - WE5ST
___
So the official word is that the KAT500 can be positioned either under, or
on top of, the KPA500. It can take the weight of the KPA500. That's good to
have settled.
Of course, now one needs to mull over what to do if you've had custom covers
made by Rose Kopp or RadioDustCovers.com... Would you
> Elecraft eMail LIST GUIDELINES 2012
>
> For those of you who are new to the list, (and for those of us who have
> rapidly failing memories.. ;-) , here is a quick list of things to remember
> when posting to this list. Please save this for future reference.
>
> The most important thing to rem
> Top posting is the official standard for this list, and its especially
> important for those of us who also read our email on Android PDA phones,
> iPads etc. Scrolling though a long thread before getting to the reply text is
> impracticable on these devices and costs us a lot of time.
>
> R
> If you have misplaced your elecraft list password, or if you never received
> it, here is how to get it sent to you again.
>
> Go to: http://mailman.qth.net/mailman/listinfo/elecraft
>
> and scroll to the bottom of the page. Enter your email address (the one you
> used for the list) and clic
Now Rose can make covers for the various stacking set ups. Two items
protected by one cover.
Nelson, K8DJC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: ma
I've always wanted an accessory tuning knob. A good friend just bought
a K3 to replace his Orion II and the ONE thing he mentions all the time
that he misses is the lack of a remote tuning knob like he had on his Orion.
Which got me to thinking
With the introduction of the P3SVGA option bo
I recently became aware of the Rev D upgrade kit for the KPA100 at
Elecraft. Where can I find a description of the changes and a
recommendation of why I would want to install this kit in my Rev A
amplifier which works FB.
Thanks. Syd WB4W
_
Look up K-Tune by G4ILO. Julian has not done any development on it for
a while - and probably won't - but the basics are applicable to either
the Griffin or Shuttle knobs.
73,
... Joe, W4TV
On 3/31/2012 3:58 PM, Gary K9GS wrote:
> I've always wanted an accessory tuning knob. A good frie
If the KAT500 is placed below the KPA500, this combination will have to sit
level on the desk because the KAT500 doesn't appear to have a bale. If the
KAT500 sits on top with one or more coax connections and the KPA500 bale is
extended, it seems this might cause the tuner to slide backwards as
Syd,
If your KPA100 has red toroid cores at L15 and L16, install KPA100UPKT.
That kit will upgrade any level KPA100 to the latest. If you do not
have a shield over the speaker magnet, add the KPA100SHLDKT as well to
upgrade your shield.
Those mods will add significantly to the stability of
Hello Joe,
Yes, I've seen that. It seems like there is a lot of functionality left
on the table. I was thinking some Elecraft engineering brain-power is
what's needed.
On 3/31/2012 3:47 PM, Joe Subich, W4TV wrote:
> Look up K-Tune by G4ILO. Julian has not done any development on it for
> a
Yes Gary,
I agree with him.
I have been suggesting for years that Elecraft do a blatant copy of the Ten-Tec
knob complete with keypad and perhaps function keys that could be set with
macros.
I loved using it with my Omni's and still miss it.
Maybe someday they will surprise us!
Rick
K6LE
O
I have just taken delivery of P3 kit S/N 2008, firmware version 01.13. I am
using this with K3 S/N 1465 mcu firmware version 04.39. The P3 and K3 work
fine together. However, I cannot establish any communication between the K3
and my PC running HRD v 5 when the P3 is powered on. Other users have
re
Yes, put the desired p3 firmware file in a folder by itself and navigate in the
P3 utility to that folder. Then press send all firmware.
Dick, K6KR
On Mar 31, 2012, at 15:21, G4DJJ wrote:
> I have just taken delivery of P3 kit S/N 2008, firmware version 01.13. I am
> using this with K3 S/N 14
Well I went and did it!
Just ordered my KX3 - been saving my pennies and selling some stuff - now just
a matter of time.
Been "lurking" for a couple of weeks and really appreciate the group's wisdom
and collegiality.
Joe, w9jc
__
Elecr
The only place I want to see one is in my shack. Where it rests I
don't care. I'm ready guys...
K9IL
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.h
Folks,
Before I get more questions indicating confusion, let me clarify in
detail --
In my response below, I ignored the poster's reference to a "Rev D
Upgrade kit". There is no Rev D KPA100 - the closest I can imagine to
Rev D is the manual revision, which is now Rev E.
The manual's rev let
I was just scolded for using the original poster's terminology (it's a
KPA100UPKT, not a Rev D upgrade) but I'm glad Don finally answered my
question about the shields.
It's hard for regular people (i.e. everyone except Elecraft) to know
about rev levels and which mod kits to order (I'd bet things
*Phil,
Withe bail in the up position and I imagine the light weight of the KAT-500
I wonder if the trick will be to place the KAT-500 on top either the K3 or
KPA-500 and NOT have it slide off the back?
I run portable everyday and bench top area is very limited so I am in a
quandry as to how I can
I was not annoyed, but wanted to produce clarity for everyone. Sorry if
I was harsh, I didn't mean it that way.
I do realize that the level of Elecraft gear can be confusing for those
who do not work with it regularly.
I am here to help, not criticize, but to be clear we all have to refer
to th
Anyone know the range for the 100w amp?
--
Mike W0MU
W0MU-1 CC Cluster w0mu.net
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.ne
*Eric,
Well that answered my concerns regarding placing under the K3/KPA-500
nicely.
Thanks a bunch.
Gary
*
On 1 April 2012 04:29, Eric Swartz WA6HHQ - Elecraft wrote:
> There should be no interaction issues between the KAT500 and the KPA500
> when the KAT is under the amp. We also beefed up th
I would not bet on the KAT500 being a lightweight. Those large toroid
cores are heavy. Certainly not as heavy as the KPA500, but not a
lightweight either.
The KAT100 had little brackets that could be placed so as to capture the
rear feet of the K2, so maybe some similar bracket will be provid
Range?
Eric
www.elecraft.com
_..._
On Mar 31, 2012, at 5:06 PM, W0MU Mike Fatchett wrote:
> Anyone know the range for the 100w amp?
>
> --
> Mike W0MU
>
> W0MU-1 CC Cluster w0mu.net
>
> __
> Elecraft mailing list
> Home: http://
Ballpark price? If it is on the web I am blind! Hi!
Mike W0MU
W0MU-1 CC Cluster w0mu.net
On 3/31/2012 6:22 PM, Eric Swartz WA6HHQ - Elecraft wrote:
> Range?
>
> Eric
>
> www.elecraft.com
> _..._
>
>
>
> On Mar 31, 2012, at 5:06 PM, W0MU Mike Fatchett wrote:
>
>> Anyone know the range for the
The KAT500 uses steel panels for rigidity and extra weight. It won't
move around under normal circumstances.
Wayne
N6KR
On Mar 31, 2012, at 5:12 PM, Don Wilhelm wrote:
> I would not bet on the KAT500 being a lightweight. Those large toroid
> cores are heavy. Certainly not as heavy as the KP
First let me say that I do not work for Elecraft. I do NOT have any inside
information. This is just a wild GUESS.
KXPA100 $499.95 plus tax and shipping
And OBTW It is NOT April 1 yet either!
73,
Bill - K6WLM
__
Elecraft mai
I bet I could throw it a good 20-25 feet.
On Sat, 31 Mar 2012, Eric Swartz WA6HHQ - Elecraft wrote:
> Range?
>
> On Mar 31, 2012, at 5:06 PM, W0MU Mike Fatchett wrote:
>
>> Anyone know the range for the 100w amp?
--
Hisashi T Fujinaka - ht...@twofifty.com
BSEE(6/86) + BSChem(3/95) + BAEnglish
We haven't set the price yet, as we are still working on it and will have
to,look at the final rollup for the manufactured cost.
Stay tuned!
73,
Eric
www.elecraft.com
_..._
On Mar 31, 2012, at 5:28 PM, W0MU Mike Fatchett wrote:
> Ballpark price? If it is on the web I am blind! Hi!
>
>
Good Evening,
A soggy day spent reading by the fire is a good day. Not much snow
last night and today it is all gone. Propagation has been all over the
map lately. One day it is great the next you cannot hear a thing. The
sun has been mildly active but sunspot 1429 is back to wreak havoc
The KX3 Software page, with the latest KX3 Utility, is now up on our web page.
Its linked to from our main Software & F/W page, and from the KX3 page.
The direct address is:
http://www.elecraft.com/KX3/KX3_software.htm
73, Eric
www.elecraft.com
_..._
___
71 matches
Mail list logo