Re: [Elecraft] Announcing the KX2 80-10 m, SSB/CW/Data transceiver

Ron, Mike's question was "Will the Begali "Adventure" paddles fit the KX2 as well as the KX3?" Is your answer for the Adventure or for the KXPD3? My take is that it's safe to assume that the Adventure screws might be even longer than the longest one on the KXPD3 -- lacking an input from

Re: [Elecraft] PL-259 connectors

Used PL259s on my 432 array,, was up for 15 year and taped and coated with silicon seal,, looked like new when I took them down and the match was 1.1 good connectors Bob K3DJC > On connections open to the air (on a ship that meant constant salt > spray) we > carefully sealed the

Re: [Elecraft] KX2 no assembly?

The KX2 options can be added at any time in the field. No return to factory required. 73, Lyle KK7P Can the ATU and RTC be added later or are they only factory fit at > build/purchase ? > __ Elecraft mailing list Home:

Re: [Elecraft] Announcing the KX2 80-10 m, SSB/CW/Data transceiver

Engineering tells me they clear, even with the long tip, but the long one is only a few mil away from an inductor, so a good tightening could end up hitting the inductor and damaging the main board. You can order a second short screw to replace the longer one with. That also eliminates any

Re: [Elecraft] KX2 no assembly?

Can the ATU and RTC be added later or are they only factory fit at build/purchase ? 73, Warren vk3byd > > Message: 27 > Date: Thu, 19 May 2016 17:21:49 -0400 > From: Wayne Burdick > To: Jim Finan > Cc: Ron D'Eau Claire , Martin Sole

Re: [Elecraft] PL-259 connectors

That was my experience servicing radio installation on board large ships. We used whatever the local supplier had on hand. After all, it's just a simple two-circuit connector designed for 28 MHz or so (back then "UHF" was 28 MHz and above, but there was really nothing above about 50 MHz before

[Elecraft] K3s arrived today

I had it assembled in a few hours and only one glitch - one of the TMP coax connectors had an intermittent so I was getting no Reference to the synth board. I re-crimped the connector and voila! it all came to life. Now I'm just letting it burn in overnight and I'll calibrate it using a GPSDO

Re: [Elecraft] PL-259 connectors

I have used Generic PL259's for decades, and while I have had a few bad ones, they usually failed while I was soldering them. But for amateur use, they are fine. Correctly soldered, a connector shouldn't have an issue holding your body weight. :) (Flame retardant suit on) Mike va3mw On Thu,

Re: [Elecraft] Announcing the KX2 80-10 m, SSB/CW/Data transceiver

Mike, From the KX2 FAQ http://www.elecraft.com/manual/KX2%20FAQ%20v-1-1a.pdf "Q: Can I use a KXPD3 with the KX2? A: Yes; however, you may need to update the KXPD3. If your KXPD3 has one thumb screw that’s longer than the other, order part no. E700425 to replace the original left-hand

[Elecraft] New KX2?

Hello Walter, Eric is a smart business man and Wayne is an elite engineer. Both KX2 and K3S are product life cycle extension to fully utilize the existing R  These products are only evolution and not revolution. I trust Elecraft will use the cash generated from the above products to produce a

Re: [Elecraft] Dayton

Anyone who looks at the order page knows. It is $749, factory assembled. Not available as a kit. ATU and battery options take it over $1000. http://www.elecraft.com/elecraft_prod_list.htm#kx2 wunder K6WRU Walter Underwood CM87wj

Re: [Elecraft] New 200 Hz K3 filter

I just bought the new 200Hz filter and I really like it. I have no issues with the gain setting; I have it set to 3 and it's running fine. 73, Gary KA1J > Was there ever a response to the question: > Is there enough IF gain to compensate for the loss of this filter? > > If one used

Re: [Elecraft] Dayton

Anyone know how much NK 9G Sent from my iPad > On May 19, 2016, at 1:51 PM, Lynn W. Taylor, WB6UUT > wrote: > > Besides the exciting KX2? > >> On 5/19/2016 8:14 AM, wa9fvp wrote: >> Anything new @ Dayton? >> > >

Re: [Elecraft] Feature request: Mini-banana ground jack for KX3

Put a BNC grounding lug under the BNC connector and clip to it. http://www.amphenolrf.com/031-10152-rfx.html wunder K6WRU Walter Underwood CM87wj http://observer.wunderwood.org/ (my blog) > On May 19, 2016, at 3:37 PM, Bob N3MNT

Re: [Elecraft] Feature request: Mini-banana ground jack for KX3

I am thinking a simple terminal lug modified with a female mini-bananna plug connector that can be secured under one of the four case screws would solve this issue. -- View this message in context:

[Elecraft] Feature request: Mini-banana ground jack for KX3

Hi Elecraft folks, Not sure how feasible it might be, but adding a mini-banana ground jack to the KX3, just like as on the new KX2, would be a huge upgrade in my estimation. Thanks again, and keep innovating. Bruce __ Elecraft mailing

Re: [Elecraft] Announcing the KX2 80-10 m, SSB/CW/Data transceiver

Will the Begali "Adventure" paddles fit the KX2 as well as the KX3? Mike KD8RQE In a message dated 5/19/2016 5:37:10 P.M. Eastern Daylight Time, n...@elecraft.com writes: Introducing the Elecraft KX2 transceiver -- the newest member of our compact KX Line. The KX2 has features very

Re: [Elecraft] Announcing the KX2 80-10 m, SSB/CW/Data transceiver

Hi Mike, manual, FAQs, etc. are now quite prominently on Elecraft's main page. ;-) To answer some of your questions (per the manual): 2. No. 3. Backed up by 2 "super cap" holding data for about 2 hours which should be enough to recharge the battery pack. 73, Olli - DH8BQA Contest, DX &

Re: [Elecraft] Announcing the KX2 80-10 m, SSB/CW/Data transceiver

To answer some of my own questions ... (just found the online manual): a.) Seems not. :-( b.) Yes. c.) Still unanswered. Not meaning 0 but real measurements (important for transverter use). d.) Listening to AM signals in SSB mode only. Hmm ... e.) No FM. Still a pity as just a firmware option

[Elecraft] Panadapters for a MM station using 4 K3s

I'm looking for some input on the best and most cost effective way to add panadapters to my MM contest station with four K3's. I currently have one of the four station outfitted with a LP PAN2 and NaP3 SW and it works fine with the internal sound card with 48Khz bandwidth. I would like to

Re: [Elecraft] Announcing the KX2 80-10 m, SSB/CW/Data transceiver

Wayne wrote: > Introducing the Elecraft KX2 transceiver -- the newest member of our compact > KX Line. > ... > For further details, please visit www.elecraft.com. But...some useful links are still hidden! Phil Genera posted these **most** helpful URLs: > Manual:

Re: [Elecraft] Announcing the KX2 80-10 m, SSB/CW/Data transceiver

Amazing news, Wayne. Allow me a couple of questions: a.) Will it support the 8 kHz IF shift as in the KX3? Otherwise probably the same trouble as with the KX3 with AM breakthrough (which is a problem here in Europe and rendered my KXFL3 useless lot's of times as I had to switch on the IF

Re: [Elecraft] KX2 no assembly?

Yes to both. Wayne http://www.elecraft.com > On May 19, 2016, at 4:15 PM, Jim Finan wrote: > > Speaking of assembly, is the KX2 built/assembled in the US like other > Elecraft gear? Was wondering the same about the K-pod since it comes > assembled also. > > 73, >

[Elecraft] Hamvention discounts

Any advantage to ordering during the Hamvention? If so, do the same discounts apply to phone or internet orders or do you have to be physically present in Dayton to take advantage? Thanks. 73 Mike KD8RQE __ Elecraft mailing list

Re: [Elecraft] K3/K3S option request

Yes please. I thought this was already on "the list". On May 19, 2016, at 9:26 AM, Peter Pauly wrote: > Related request - can we please save the filter bandwidth per mode? > > On Thu, May 19, 2016 at 9:59 AM, Kjeld Holm wrote: > >> Dear Elecraft >>

[Elecraft] For sale: KX3-4M-NOAT

Hello.. Bought new 4m module for use in my KX3 on DXpedition, but could not get license, so unit never used. $225 shipped CONUS. Dick, K5AND __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft

Re: [Elecraft] KX2 no assembly?

The KX2 uses state-of-the-art, high density construction techniques. We felt that some builders might have difficulty with the small hardware and connectors, so we're only offering it factory assembled. 73, Wayne N6KR http://www.elecraft.com > On May 19, 2016, at 11:03 AM, Martin Sole

Re: [Elecraft] KX2 no assembly?

Speaking of assembly, is the KX2 built/assembled in the US like other Elecraft gear? Was wondering the same about the K-pod since it comes assembled also.  73, Jim Jim Finan AB4AC  Sent from my BlackBerry 10 smartphone.   Original Message   From: Ron D'Eau Claire Sent: Thursday, May 19, 2016

Re: [Elecraft] KX2 no assembly?

So far, but like other Elecraft rigs customers can easily add options such as the ATU. 73 Ron AC7AC -Original Message- From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Martin Sole Sent: Thursday, May 19, 2016 9:04 AM To: elecraft@mailman.qth.net Subject: [Elecraft]

[Elecraft] Creative Lab EMU-0202

I just re-installed my EMU-0202 sound card. I wanted to see if I could make it play with Windows 10 and everything else I have running, Win4K3, CW Skimmer, and HRD. I've always liked the fact that there was less "garbage" being displayed on the spectrum display. What I found it that Windows 10

[Elecraft] Announcing the KX2 80-10 m, SSB/CW/Data transceiver

Introducing the Elecraft KX2 transceiver -- the newest member of our compact KX Line. The KX2 has features very similar to the KX3, at about half the size and weight. It fits easily in a jacket pocket. It can even be used hand-held, with a built-in mic to facilitate HT-style operation.

[Elecraft] New KX2 - Field Test Photos

Nice photos compliments of Steve WG0AT and Wayne N6KR... http://www.zerobeat.net/wb8yqj/ft1.jpg http://www.zerobeat.net/wb8yqj/ft2.jpg http://www.zerobeat.net/wb8yqj/ft3.jpg Great price point and KX2 will be available at Dayton and via online orders.  de Don wb8yqj

Re: [Elecraft] New KX2?

Not sure what you mean by "rugged". It's a very similar case to the KX3, just smaller. Opens clamshell-like just like the KX3 only with two thumbscrews instead of four. Not waterproof, but like the KX3 its pretty well "shockproof" when packed with camping gear or sitting on a rock for an operating

Re: [Elecraft] New 200 Hz K3 filter

It's about the same as the 5-pole filter. Wayne N6KR http://www.elecraft.com > On May 19, 2016, at 1:14 PM, brian wrote: > > Was there ever a response to the question: > Is there enough IF gain to compensate for the loss of this filter? > > If one used spectrogram

[Elecraft] [K3/P3] OT - For Sale

Please respond directly to me to keep list FOD down. After much contemplation and my operating habits changing, I have decided to sell my K3/P3 combo (I am keeping my KX3 and will upgrade to the PX3 and, later, the KXPA100). Here’s what I have: K3 S/N: 59xx 100W kit (bought in November 2011)

[Elecraft] New 200 Hz K3 filter

Was there ever a response to the question: Is there enough IF gain to compensate for the loss of this filter? If one used spectrogram to try and set filter gains, there barely was enough gain with the old 200Hz filter to achieve same peak audio output within 1db of a carrier relative to the

Re: [Elecraft] [ KX2] KXBT2 Charger

I charged my Li-ion batteries by a voltage regulator LM317 set to 12.6V. Never a problem and the battery lasted but the regulator needs a sink. It would be really convenient to be able to charge (even slower) without removing the battery. It would really be nice to add internal Li-Ion option to

Re: [Elecraft] Dayton

All we got at Visalia was a knob. ;) 73 jeff wk6i On Thu, May 19, 2016 at 10:51 AM, Lynn W. Taylor, WB6UUT < k...@coldrockshotbrooms.com> wrote: > Besides the exciting KX2? > > On 5/19/2016 8:14 AM, wa9fvp wrote: > >> Anything new @ Dayton? >> >> >

Re: [Elecraft] Dayton

Besides the exciting KX2? On 5/19/2016 8:14 AM, wa9fvp wrote: Anything new @ Dayton? __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

Re: [Elecraft] New KX2?

There is some sort of myth about the KX3 not being rugged. It was designed for trail use. With around 10,000 sold, I haven’t heard any reports of problems with ruggedness. My KX3 has fallen hard enough to bend the BNC connector and it works fine. I would expect the KX2 to be slightly more

Re: [Elecraft] KAT500 with KX3

Yes Bill, I believe that is correct but I want it to band follow so that the solution will be set to the last correct solution for the current frequency when only receiving. It follows the K3/KPA500 and the the question is “how do I implement this with the KX3? Michael Blake > On May

Re: [Elecraft] K3/K3S option request

Related request - can we please save the filter bandwidth per mode? On Thu, May 19, 2016 at 9:59 AM, Kjeld Holm wrote: > Dear Elecraft > > Two questions from a very satisfied user of K3. > > Would it be possible to save the AF setting for each VFO (A resp. B)? > Reason

Re: [Elecraft] KAT500 with KX3

I believe it will sense RF on a dit or two. So only the coax is required. Sent from my iPhone ...nr4c. bill > On May 19, 2016, at 11:06 AM, Michael Blake wrote: > > Which data connection(s) do I use to control the band/frequency settings on > the KAT500 when the transceiver

Re: [Elecraft] [ KX2] KXBT2 Charger

I feel kind of stupid buying a charger when I have a very expensive bench power supply. Does that battery pack have a balancing circuit and over voltage protection? On Thu, May 19, 2016 at 11:54 AM, Jerry Moore wrote: > KXBT2 Charger: Can the charger be connected to a

[Elecraft] KX2 no assembly?

Looks like only factory fully assembled. Another first for Elecraft? __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This

[Elecraft] [ KX2] KXBT2 Charger

KXBT2 Charger: Can the charger be connected to a DC power source without an inverter to charge the KXBT2 Li-Ion battery pack? Considering the intended POU is pedestrian I can see a great need/use for solar to power the charger/recharge the battery pack. Depending upon circuit design it should be

Re: [Elecraft] New KX2?

Looks cool. What I'm really curious about is if it is more "rugged " than the kx3. La4tta Erlend 19. mai 2016 17:23 skrev "Phil Genera" : > Manual: http://www.elecraft.com/manual/KX2%20owner's%20man%20A4.pdf > FAQ: http://www.elecraft.com/manual/KX2%20FAQ%20v-1-1a.pdf > >

Re: [Elecraft] KX2 on the way...

Real nifty! Makes one wish one did camping or mountain climbing or something that would require toting a little rig around... I'll be in line for a K4 if it comes out. I'm just as happy that it isn't this year; there is still a lot of use left in the old K3... 73, Drew AF2Z On 05/19/16

Re: [Elecraft] PL-259 connectors

Believe I read somewhere that Amphenol connectors are being made in Mexico...not sure how long ago that got started. 73, Joe W2KJ I QRP, therefore I am On May 19, 2016, at 11:05 AM, Drew AF2Z wrote: > It was an 83-1sp I recently bought that had

Re: [Elecraft] New KX2?

Manual: http://www.elecraft.com/manual/KX2%20owner's%20man%20A4.pdf FAQ: http://www.elecraft.com/manual/KX2%20FAQ%20v-1-1a.pdf -- Phil On Thu, May 19, 2016 at 11:10 AM, Jim Finan wrote: > Up on Order page with a link to the spec sheet. > > Didn't see it listed yet in 'Order

Re: [Elecraft] PL-259 connectors

On Thu,5/19/2016 8:05 AM, Drew AF2Z wrote: It was an 83-1sp I recently bought that had defective threading. I've seen this as well in perhaps 1% or less of the Amphenol 83-1SPs that I've bought and installed. The symptom is that the height of the thread is shorter than it should be, and you

[Elecraft] Dayton

Anything new @ Dayton? - Jack WA9FVP Sent from my TRS-80 :-) -- View this message in context: http://elecraft.365791.n2.nabble.com/Dayton-tp7617618.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft

Re: [Elecraft] New KX2?

Up on Order page with a link to the spec sheet.  Didn't see it listed yet in 'Order Status'. Jim  Jim Finan AB4AC  Sent from my BlackBerry 10 smartphone.   Original Message   From: Edward R Cole Sent: Thursday, May 19, 2016 4:22 AM To: Elecraft@mailman.qth.net Subject: Re: [Elecraft] New KX2?

[Elecraft] KAT500 with KX3

Which data connection(s) do I use to control the band/frequency settings on the KAT500 when the transceiver is a KX3? The amplifier is a low drive modified ALS-600 which seems like a straight forward keying connection but I am not sure about the data connection from the KX3’s E980232 "Cable

Re: [Elecraft] PL-259 connectors

It was an 83-1sp I recently bought that had defective threading. Let's face it: the name brand products of the past are not what they used to be, quality-wise. (Some others I will never buy again: Grundig, Levis, Herman boots...) Mental note to self regarding PL-259's-- check for defective

[Elecraft] KX2 Leaked 9 Years Ago!

I don't know what the big deal is about the KX2. It was leaked in this thread 9 years ago! 73, Alan N5NA __ Elecraft mailing list Home:

[Elecraft] KX2 stable enough for JT9 ??

Any intelligence on narrow Digit modes? Dan VA3MA __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by:

Re: [Elecraft] RFI and Direct tv or Dish network

On Thu,5/19/2016 6:41 AM, Warren Merkel wrote: Thanks for the note Jim, However I've already got multiple passes of the OCF Feedline fed through a stack of five 2.4" #31 donuts, per your very own, excellent RFI-Ham.pdf article. Picture on my QRZ page. https://www.qrz.com/db/KD4Z But that

[Elecraft] K3/K3S option request

Dear Elecraft Two questions from a very satisfied user of K3. Would it be possible to save the AF setting for each VFO (A resp. B)? Reason for asking: I am nearly always controlling my K3 from HRD with the physical AF knobs at zero. Often I am using a digital mode (JT65) on the one VFO and CW on

Re: [Elecraft] RFI and Direct tv or Dish network

Thanks for the note Jim, However I've already got multiple passes of the OCF Feedline fed through a stack of five 2.4" #31 donuts, per your very own, excellent RFI-Ham.pdf article. Picture on my QRZ page. https://www.qrz.com/db/KD4Z The RG6 has a stack of three donuts with a large number

Re: [Elecraft] PL-259 connectors

Type N connectors are great! I just don't see where is any gain to using them on HF! They will make NO difference on either end of your QSO. Most of the PL259's I see for sale today are crap. I'm a professional in the communications industry so I use both styles on a Dailey basis The 83-1SP's

Re: [Elecraft] PL-259 connectors

Unfortunately probably no manufacture is using Amphenol jacks. I have had N jack failures in equipment where non-Amphenol connectors lost their spring and I previously owned an Acom amp that had very loose fitting SO-239's. John KK9A from: Barry w2up Thu May 19 08:01:25 EDT 2016 Do you think

[Elecraft] Irrelevant post about KX2

In the new spirit of posting irrelevant or non-technical posts, I have decided to contribute my own. I am pleased to state that I received the first KX2, out of the first batch of 26, in 1982, and have used it successfully for the past 34 years. I currently use it with my Elecraft K3 to work

Re: [Elecraft] PL-259 connectors

Do you think whatever you're plugging into uses Amphenol SO-239's? Barry W2UP -- View this message in context: http://elecraft.365791.n2.nabble.com/PL-259-connectors-tp7617598p7617605.html Sent from the Elecraft mailing list archive at Nabble.com.

Re: [Elecraft] PL-259 connectors

I used Amphenol exclusively until they moved their manufacturing from the USA to Mexico. Now the 83-1SP is no longer stamped, (Engraved.) its printed. (Ink?) Same quality? It could be, but it doesn't appear to be. (Cheaper phenolic/Teflon?) I have a sizeable stash of USA-made Amphenol and J

Re: [Elecraft] PL-259 connectors

I was lucky enough to purchase a master box of 1000 of those 83-1SP's back in the late 70's when they were REALLY silver plated. I have enough for a life time GREAT connectors and with them, no fool would ever need a Type N W5SUM -Original Message- From: Todd Ruby Sent:

Re: [Elecraft] New KX2?

Guess if it is unveiled at Dayton - more excitement! Quick look-over and doesn't appear to replace my KX3 which has more to offer me. I don't do SOTA so don't need super-small. Will enjoy reading about it once details are published. 73, Ed - KL7UW http://www.kl7uw.com "Kits made by

Re: [Elecraft] RFI and Direct tv or Dish network

First off, the Dish-NET receiver produced no RFI. It was not digital satellite so used s-video connections to Home Theater receiver which was connected to TV via HDMI. New Direct-TV receiver is high-def digital receiver so it uses HDMI interconnect to home theater. TV/home theater is on