Doesn't the K3 automatically save settings every so often via a timer? So it
would only revert to an earlier state if the power fails 'shortly' after making
a change.
Vic 4X6GP
> On 1 Jun 2016, at 3:41 AM, Jim Brown wrote:
>
>> On Tue,5/31/2016 4:22 AM,
I used to just cut power,, but the K3 really didnt like that
but I got away with it always turn off before cutting power
Bob K3DJC
On Tue, 31 May 2016 22:37:02 -0400 Don Wilhelm
writes:
> The K3 (K3S) can also be turned off safely (and store the current
>
I forgot to add that if you permanently connect the ACC POWER_ON pin to
ground, you will not be able to turn the K3 off with the PS0 command.
It may glitch to a power off state, but will come back on almost
immediately.
73,
Don W3FPR
On Tue,5/31/2016 7:09 PM, j...@kk9a.com wrote:
I ask this because during my second contest ever with my new K3S and I had
two power failures. So it goes back to the state that it was in when last
properly shut off - That works for me!
I run all the 12V gear in my shack from batteries, so the
The K3 (K3S) can also be turned off safely (and store the current
settings) by using the PS0 command - see the Programmer's Reference.
That command cannot be used to turn it on (there is no power to the K3),
so the POWER_ON pin in the ACC connector can be pulled low by an
external device.
If
I ask this because during my second contest ever with my new K3S and I had
two power failures. So it goes back to the state that it was in when last
properly shut off - That works for me!
John KK9A
Jim Brown jim at audiosystemsgroup.com
Tue May 31 20:41:39 EDT 2016
]
On Tue,5/31/2016 4:22 AM,
Hi all,
We could use a few more current KX2 owners to load the new code. Have to make
sure I haven't fixed what wasn't broken.
To load firmware, you'll need to install KX2 Utility on a PC, Mac, etc.
Please contact me off-list.
tnx
Wayne
N6KR
On Tue,5/31/2016 4:22 AM, j...@kk9a.com wrote:
How do you save the current settings? I think most of us at some point in
our lives have had a power failure while operating.
Turn the K3 off with its power switch and turn it back on. You will, of
course, have to do that each time you change
Same here. It works quite well and has rear hole centers for the AMPS
pattern (ball-mount).
73,
matt W6NIA
On 5/31/2016 5:29 PM, WD4SDC wrote:
Larry,
I used this to do a KX3 dash mount, but it may also work using a pole mount:
I use the aux out on my SignaLink USB to go to my powered speakers. I
can hear simultaneously what I'm decoding using the built in sound
card. I found this is the easiest to do and requires nothing other
than invoking the digital software I use, no cable changes.
Yes, you can use a "splitter"
Larry I will have one that works great in just a few weeks. look at some
posting on my web site.
GEMS Home Page
| |
| | | | | | | |
| GEMS Home PageI am Scott AK6Q. |
| |
| View on www.gemsproducts... | Preview by Yahoo |
| |
| |
Scott AK6Q
On Tuesday, May 31, 2016
> We looked at this in independent reviews and our in-house plots. The
> keying BW looks pretty much the same on all three rigs. The 100 W K3
> may be a tiny bit better, but there's nowhere near "twice" the
> difference.
While the graphs in QST are not the best in the world, I'm comparing
the
Larry,
I used this to do a KX3 dash mount, but it may also work using a pole mount:
http://www.gpscity.com/ram-mount-plastic-universal-finger-grip-clamping-cradle.html
It "finger grips" the radio. I've had it in an out of the car on almost a
daily basis (because I can't be without my KX3 ;) )
I am setting up my K3 with N1MM, so far I have the K3 transmitting and
receiving on RTTY, using the Microham.
But my problem is The router and N1mm are not seeing the K3 to report the
frequency etc.
Can someone please let me know what settings in the router and N1MM will ensure
that they talk
Have you configured the K3 for DATA A, MENU:MIC SEL=LINE IN and set
up audio levels in microKEYER and your sound card as documented in
"Setting Audio Levels" in the MK Users Manual?
I have no experience with M110A but MK and the K3 should operate the
same way for any audio based data mode. I
what he said. Bob W3DK
> -Original Message-
> From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Tony
> G6GLP
> Sent: Tuesday, May 31, 2016 5:07 PM
> To: elecraft@mailman.qth.net
> Subject: [Elecraft] K-Pod order status
>
> Hi All,
>
> With all this talk about the KX2
This is near the top of the firmware list for both radios.
Wayne
On May 31, 2016, at 4:47 PM, thelastdb wrote:
> I'll second this request.
> Myron WVØHPrinted on Recycled Data Original message From:
> John Oppenheimer Date: 5/31/2016
I'll second this request.
Myron WVØHPrinted on Recycled Data Original message From: John
Oppenheimer Date: 5/31/2016 2:15 PM (GMT-06:00) To:
elecraft@mailman.qth.net Subject: Re: [Elecraft] Suggested KX3 "upgrade"
My general operating style is to use a CW
Took a new ham & friend (who’s interested in learn code and using it in the
filed) up Mt Herman this morning to experience his first SOTA activation! We
were on 17/20m SSB. Stellar morning sunny 60s with a few white puffy clouds.
I set up the KX2 on 17m, thru a wire up a tree and took the
Does anyone have a good mounting bracket for the KX3? I want to mount it to
a pole in my 2006 Expedition so need a bracket from the KX3 to the pole. I
don't have the pole yet so if you have a pole you like, please tell me what
that is as well.
Regards,
Larry
KG7ZSB
You cannot live a
Hi All,
With all this talk about the KX2 and its order status the mention of the
K-POD seems to have lost focus in the list here. I hope the KX2 status
will or is not having an impact on the delivery status of the K-POD. The
info I have is it will start shipping around 13 June a short two
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of TFJM
via Elecraft
Sent: 30 May 2016 23:39
To: elecraft@mailman.qth.net
Subject: [Elecraft] KX3 & Loop Antennas
Has anyone had much success using either an Alex Loop or Chameleon P Loop
antenna with
This is on the wish-list.
tnx
Wayne
N6KR
On May 31, 2016, at 1:06 PM, Scott Dupuie wrote:
> Wayne,
>
> Have you ever considered implementing an audible SWR indicator (lower tones
> better SSR, higher tones worse SWR, or something like that)? I would find
> this very handy
Hi everyone,
Its been a busy last couple of weeks at Elecraft! We are still recovering from
Dayton and are working on entering all of the latest KX2 web orders .
At the moment we are overloaded by all the email requests for KX2 order status
(some just a couple of days after order.) This in
Joe,
The KX3, KX2, and K3/K3S should have virtually the same keying bandwidth. They
all use the same raised-cosine keying envelope shape, and this is by far the
dominant factor unless the transmit final amplifier is being overdriven.
We looked at this in independent reviews and our in-house
Hi Terry
I never saw anyone answer your question and I just got home from work so I
could not do it earlier. I just took my KX3, PX3 and PA3 camping this week end
and had the exact same problem you describe. I had one cable in the wrong place
so here is what you need to make sure you do. The
We just completed the first phase of accessibility improvements for the KX2.
The CW audio-tone interface now covers all front panel switches and knobs
(except frequency memory store/recall), bringing the KX2 up to the same level
as the KX3. Menu and frequency memory accessibility is also
Has anyone been able to get the MARS soundcard mode M110A working with their K3
and an original microKeyer? I tried to get the program working using DATA A,
but I get almost no output power. With the K3 set to 50 watts, I get maybe 5
watts output as monitored with a Bird wattmeter.
M110A
Hi everyone,
Its been a busy last couple of weeks at Elecraft! We are still recovering from
Dayton and are working on entering all of the latest KX2 web orders .
At the moment we are overloaded by all the email requests for KX2 order status
(some just a couple of days after order.) This in
Joe,
I use the aux out on my SignaLink USB to go to my powered speakers.
I can hear simultaneously what I'm decoding using the built in sound
card. I found this is the easiest to do and requires nothing other than
invoking the digital software I use, no cable changes. There is one
My general operating style is to use a CW memory REPEAT for sending CQ,
both at home and during field operations.
I sure would be nice to end the memory with a tap of the key and not
send an element. Both my new KX2 and KX3.
John KN5L
On 05/30/2016 06:27 PM, Jim Rodenkirch wrote:
> Could
The P3 has been sold. Thanks to everyone who inquired.
Dick, N5XRD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list
I don't know if this is the proper place to offer things for sale, however, I
have a P3, with the P3SVGA-F video adapter installed for sale. I
operate PSK f rom my apartment on a small antenna and don't need or use the
P3. If interested eMail me at: rhemi...@sbcglobal.net Thanks
Dick
If I could get rid of the pauses, I could use the K3s built-in USB
sound card. The KX3 doesn't have one, so I'd need an external audio
interface or sound card if I wanted total voice automation with that
rig.
Unfortunately, since the KX3 (and KX2) lack dedicated Line In/Ln Out
jacks,
Selling my K3. Serial # 6625.
Includes the following options:
KPA3 100 watt amp module
KAT3 Antenna Tuner module
KXV3 RX Antenna, XVRTR interface, IF Tap board
PR6 6 meter preamp
400Hz 8 pole CW Filter
2.8 kHz 8 pole SSB filter
13 kHz AM/FM 8 pole filter
MH2 Hand Mic
Power cable
Computer
The KX3 (no "-") requires a lot less assembly than a k3. And it connects almost
like K3 to computer. Major missing items are no DTR-RTS available on serial
connector and no dedicated Lin In/Out.
Sent from my iPhone
...nr4c. bill
> On May 31, 2016, at 11:40 AM, Mike Kasrich
On 5/31/2016 11:40 AM, Mike Kasrich wrote:
Has anyone put together a KX-3 kit. Is any more or less involved that
putting together a K-3?
I assembled both. The K3 is more involved than the KX3, but both were
straightforward. The instructions and parts lists are top-notch for both
rigs.
True, NR4C...BUTwhy should one have to push a button on the
radiothat places more stress on whichever button is employedI'd much
rather see, hopefully, some sort of fix via firmware mod, where one can use
the key to do that without adding a "wear and tear" element to expensive
KX3 is a bunch easier to build and takes much less time than the K3/K3s.
Depending on your options there are some small connectors to deal with but not
too bad. Compared to working on a cell phone it is a piece of cake.
You can download the manual(s) from the Elecraft website and check it out.
Has anyone put together a KX-3 kit. Is any more or less involved that
putting together a K-3? Anyone use a KX-3 in a contest and interfaced
with N1MM+? Any quirks/tips? and finally I am looking for a KX-3 trying
to decide between new and used. Anyone have a KX-3 they are looking to
part with?
KX1 has been sold.
Hi All,
After getting my KX3 I no longer use my KX1 and am selling it.
I built my KX1 kit in 2011 and am a very experienced builder, the radio
works perfectly. The KX1 has been always kept in my non-smoking home.
Selling the KX1 with the KXAT1 internal antenna tuner. The
Hi
Anyone got a spare KSB2, built or unbuilt kit , they want to get rid of?
E mail me off reflector please.
73 Bob G3PJT
PS repeat post as subject format error
__
Elecraft mailing list
Home:
Any button will definitely stop it, but (and this includes the K3, K3S,
KX3 and possibly the KX2 as well) oft times you will get a partial (dot
or dash) sent even when pressing a button. Even when calling CQ looking
for a general QSO this can be annoying and confusing to both the sending
I think pressing any button the KX3 will terminate the msg repeat.
Sent from my iPhone
...nr4c. bill
> On May 31, 2016, at 10:17 AM, Jim Rodenkirch wrote:
>
> My apologies for NOT stipulating my range of operations when I submitted the
> original postI feel like
My apologies for NOT stipulating my range of operations when I submitted the
original postI feel like others have posted a request for this sort of
"improvement" earlierJim R. K9JWV
--
View this message in context:
Hi
Anyone got a spare KSB2, built or unbuilt kit , they want to get rid of?
E mail me off reflector please.
73 Bob G3PJT
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Perfect, thanks!
On Tue, May 31, 2016, 02:46 Peter Pauly wrote:
> I think it's this one:
>
> http://www.amazon.com/dp/B002EQ6E9E
>
> On Tue, May 31, 2016 at 1:06 AM, Bruce Nourish wrote:
>
>> Does anyone know what model microphone Frank is using for SSB
I KNEW someone wud introduce N1MM as the answer to my "problem"/request and,
without knowing my operating "style"/focus and making an assumption, the
suggestion of using a contesting program is sorta expected.
I didn't mention "full blown contests" as a supporting argument for my
"needy
How do you save the current settings? I think most of us at some point in
our lives have had a power failure while operating.
John KK9A
Jim Brown jim at audiosystemsgroup.com
Mon May 30 21:56:46 EDT 2016
Yes. When you turn the K3 off with its power switch, it writes current
conditions to its
I think it's this one:
http://www.amazon.com/dp/B002EQ6E9E
On Tue, May 31, 2016 at 1:06 AM, Bruce Nourish wrote:
> Does anyone know what model microphone Frank is using for SSB around the
> 0:30 mark?
>
> On Mon, May 30, 2016 at 3:49 PM Peter Pauly wrote:
>
50 matches
Mail list logo