We start the outdoor QRP Season each year with FYBO in February.
The there's a long wait until the Spring Classics - QRP To The Field and the
Cookie Crumble Contest. Then in the heat of the Summer the Bumblebees and the
Skeeters take flight. In the Fall we get nutty with our NoGA friends in the
Bias on and off applies to the front panel mic Pin 1 as well as the tip
of the rear panel jack. It depends on whether you have the FP or the RP
selected.
Some Kenwood desk mics do use the power pin, but those Kenwood mics use
pin 5 instead of pin 6 for power, so you would have to re-wire the
If using a dynamic mike you should not have any connection to pin #6
anyway. So it would make no difference. The BIAS On and Off applies
to the back panel mike connection.
73
Bob, K4TAX
On 8/24/2018 10:53 AM, TL_Netvision wrote:
Hello all,
While trying different front microphones
Good for parts. The front panel board is defective. It come with a new spare
TFT color display. $160 shipped. PayPal preferred.
73, John N1JM
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home:
Hi,
By default, Avast will move any unknown file to the locker. This includes
new software like the utility. In the Avast settings, one of the first
entries is Enable CyberCapture. Set this to "allow me to decide".
Once you have done this, it will not automatically be sent to the locker,
Have no fear, it’s a “false positive”. Two of the hits are defined as
“FileRepMalware” which after some research basically means the KPA1500 Utility
has not been seen widely by the virus detection engine., which is not
unsurprising as 1.14 was brand new, and isn’t widely distributed.
Its
They splatter nicely when hit with anything over about .30 cal.
73, Charlie k3ICH
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of Bob Rennard via Elecraft
Sent: Friday, August 24, 2018 11:52 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] Recycling replaced
Oops... I think I messed up...It's the voltage to MIC input pin 1 that's
affected by bias on off.
Isaac, 4Z1TL
-הודעה מקורית-
מאת: TL_Netvision
נשלח: Friday, 24 August 2018 18:54
אל: 'elecraft@mailman.qth.net'
נושא: FP Mic 8 volts
Hello all,
While trying different front
Where I live in MO there are several local E-waste recyclers.
Here is a link that may find you one in your area -
https://allgreenrecycling.com/drop-off-locations/
Their website is not responsive to your Zip code, but web search finds -
All Green Electronics Recycling - Washington,
Hello all,
While trying different front microphones (Dynamic & Electret) I noticed that
8v on pin 6 of the mic socket is always present no matter if I set bias to
on or to off.
What am I missing please?
73, Isaac, 4Z1TL
---
This email has been checked for viruses by Avast antivirus
Dan,
The KDSP2 does quite well for SSB. Check your settings against the
defaults shown in the KDSP2 manual. Particularly the bandpass low and
high frequencies.
Secondly, make sure the 'nr' and 'nt' is set to off (no dots before them
on the display. If those are set on, they can be expected
I've had the DSP module installed in my K2 (ser. no. 03957)since I built it.
After a long hiatus, I've fired it up, realigned it successfully using
Spectragram , and the audio still sounds horrible. I've come to realize that
the parameters used for the DSP are probably not optimized for SSB.
Keep both of the old boards. They are your backup spares, and can
also be useful diagnostic aids.
Remember that your K3 requires two synthesizer boards of the same
type, so you would always need to swap them both.
73 from Ian GM3SEK
>-Original Message-
>From:
I've replaced to two synthesizer boards in my K3.
Is there a way (or does Elecraft provide a service) to recycle them, as I'm
sure they have no value?
I don't want to simply throw them into the landfill.
Thanks,
Eric W3DQ
14 matches
Mail list logo
