Good morning,
I am looking for assistance to be able to properly complete the reference
oscillator calibration.
Situation: despite moving C22 I don't see any change or correction when I
try to zero beat signal from RWM (9,996.00)
Performed procedure:
1. I tuned the K2 with the RWM signal. I was a
Great video, Frank. Thanks for sharing. I had no idea cold shrink could
potentially perform that well.
Is that what you're using on buried cables?
73
Lyn, W0LEN
> -Original Message-
> From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of
donov..
of the current situation, but wow…
I have been going back and forth with tech support via email (which of course
is half the problem) for 3 weeks now. I send an email, it gets passed to the
K3S expert, he gets a garbled message, I get a response that makes no sense, I
send another message, it
ONLY 3 weeks? Mine started 7 April and is still going on. The longest
delays seem to be between our contact person and the "K3 expert".
Eliminating the middle man would help a LOT.
K3s #11894 Overdrive Faults
--
73,
Mike Cizek W0VTT
-Original Message-
From: elecraft-boun...@mailman.q
Dave,
So, are these mods documented somewhere on the Elecraft site? I have been
unable to locate them. Further, I can't even get Elecraft to respond about when
they will provide schematics for the KPA1500.
Thanks
Mike
K7PI
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Hi Al,
The VFO tuning of the K2 is drivin by its low phase noise PLL and a
lookup table (created by CAL PLL) as well as the values stored for the
BFO settings (CAL FIL). Therefore, after adjusting the 4MHz oscillator
via C22, those routines must also be run as they depend on the new
crystal f
I have successfully used a method of water-proofing a coax splice by first
coating the outside of the connectors with silicone (di-electric) grease, then
wrapping about 18" X 5" (or?) piece of plain plastic garbage bag around the
junction.
The next step is to wrap that with several layers of goo
"As has been mentioned - shouldn't be too difficult to do this with an external
Arduino based controller. "
My brain needed something to do while I was watching 30 m for new DX so I
created a rough draft proposal for "power per frequency bin". I created this
to stimulate discussion not becaus
On 6/4/2020 8:50 PM, Ed Tanton wrote:
> I should have mentioned that. I strip 5 or 6 inches of insulation. That
> was why I cleaned the top of the ground rod and sprayed it with
> electrical lubricant. I used a stainless steel hose clamp to hold the
> stripped wires against the ground rod at each
Al,
The C22 setting does nothing to change the K2 display - you must run CAL
PLL and CAL FIL (for all filters) before any change in the display takes
place. Normally, the reference oscillator only serves as a clock for
the MCU - the frequency display does not depend on it.
See the K2 Dial C
I was operating on FT8 20 meters for quite a long time with my KPA500
running about 400 watts and heard a few pops (like something arching).
Heard it a few more times then the amp went off.
Now it will not power on. No lights, nothing. I checked the fuse and
it is OK.
Can you tell me whe
Cad-weld isn’t expensive — $11-15 per weld depending on where you buy the
stuff. Typically sold in kits of 6 one-shot crucibles, and available for
varying ground wire sizes on 1/2” or 5/8” ground rods.
Grant NQ5T
> On Jun 5, 2020, at 11:17 AM, Phil Kane wrote:
>
> On 6/4/2020 8:50 PM, Ed Tan
First time I've ever heard of this product and it's quite intriguing. Where
is this available from in quantities a typical home station would use? I go
through a 3 foot section of .75" marine grade heat shrink in about 3-5
years.
- pjd
-Original Message-
From: elecraft-boun...@mailman.qt
My whole ground system is Cadweld bonded. I bought the new style shots and
purchased the igniter from Joel and the RF Connection in MD. Couldn't have been
happier. And they're fun to fire off, too!
- pjd
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of Grant Yo
DigiKey has it in 6” or 8” pieces of various diameters. It runs around $25.00
per piece, with quantity discounts. Not inexpensive …
Grant NQ5T
> On Jun 5, 2020, at 12:13 PM, Peter Dougherty wrote:
>
> First time I've ever heard of this product and it's quite intriguing. Where
> is this avail
"Can you tell me where to start looking?"
A report of a similar event was posted just a few weeks ago. Some of us were
assuming it was a KPA500 failure but it turned out to be a failure of the input
AC voltage.
Is AC power present? Does the KPA500 power up if connected to a known good
power
With all due respect, if you don't know where to start looking, then
please don't.
Unless you really know what you're doing, then you should not remove the
lid. Fault finding could easily result in the need to power up and
expose yourself to many hidden dangers.
It's been suggested that lack
Recently I'vetried to add K6XX Cw Indicator and W3FPR Fixed Audio Output to my
K2 (# above 4000).
Something went wrong when I was soldering wiresto Control Board and Front
Panel Board and the result is following:
- radio freezes at startup,
- when R5 (RIT) pot is fully CW display stops wi
Hi Lynn,
I have no buried cable splices in my ham station. The only splices
I once had failed years ago:
- The buried AC power feed from the street was fabricated from two
spliced cables. The neutral wire splice failed causing a near-catastrophe
in my home
- the buried 240 volt AC power
Fuses!
400 Watts “for quite a long time”? Bet the fans were happy.
Sent from my iPhone
...nr4c. bill
> On Jun 5, 2020, at 12:07 PM, Tom Berry wrote:
>
> I was operating on FT8 20 meters for quite a long time with my KPA500
> running about 400 watts and heard a few pops (like something ar
Hi Phil,
I use Erico One Shot cad welds on my workshop grounding system. Everything is
tied together with cad welded bare 6 AWG and I have 8 foot ground rods,
although I had to drive them in at an angle. Our house is on top of a mountain
in TN and soil depth varies from probably 6 ft deep to ex
Ouch! I'll get a few of these but reserve them for anything in the air that's
difficult to access. I still have about 5 feet of the Ancor marine heat shrink
for anything at ground level.
- pjd
-Original Message-
From: Grant Youngman
DigiKey has it in 6” or 8” pieces of various diam
I meant to add I couldn't get the shots to fire with the sparking tool I
purchased so I ran down to a fireworks store and purchased a box of sparklers.
They do a ***fantastic*** job at ignition.
Then when you're done after things cool a few gentle taps with a hammer breaks
off the thin ceramic
On 6/5/2020 9:05 AM, Grant Youngman wrote:
> Cad-weld isn’t expensive — $11-15 per weld depending on where you buy
> the stuff. Typically sold in kits of 6 one-shot crucibles, and
> available for varying ground wire sizes on 1/2” or 5/8” ground rods.
Agreed, but how many of us would go through t
There’re a couple things in series with the transformer primaries that look
like thermistors. Wonder about them. They’re labeled T and SL 1, and SL 2.
Chuck Jack Hawley
KE9UW
Sent from my iPhone, cjack
> On Jun 5, 2020, at 12:08 PM, Nr4c wrote:
>
> Fuses!
>
> 400 Watts “for quite a long t
Yeah, maybe I'm one of the exceptions. I just used 20 of them to build a
lightning ground system for a new tower install. Easy to use and considerable
peace of mind knowing the joints created will last a long time underground.
--
Art Greenberg
WA2LLN
a...@artg.tv
On Fri, Jun 5, 2020, at 13:32,
Tom,
The best place to start is with your AC Power. If that is OK, the next
step is to email supp...@elecraft.com.
73,
Don W3FPR
On 6/5/2020 12:04 PM, Tom Berry wrote:
I was operating on FT8 20 meters for quite a long time with my KPA500
running about 400 watts and heard a few pops (like s
Cad-weld seems a easier than the other approach described. It is more robust
against corrosion, plus it is fun.
I just don’t see a downside. :-)
wunder
K6WRU
Walter Underwood
CM87wj
http://observer.wunderwood.org/ (my blog)
> On Jun 5, 2020, at 10:32 AM, Phil Kane wrote:
>
> On 6/5/2020 9:05
On 6/5/2020 8:17 AM, Phil Kane wrote:
For our commercial and public safety
communication site grounding systems our firm insists on cad-weld at all
exposed and buried connection points but I would suspect that very few
hams, let alone residential or even commercial electricians, would go to
that
On 6/5/2020 9:33 AM, Alan - G4GNX wrote:
Unless you really know what you're doing, then you should not remove the
lid. Fault finding could easily result in the need to power up and
expose yourself to many hidden dangers.
Ummm -- we're hams, and are supposed to have at least some technical
bac
On 6/5/2020 10:23 AM, Chris Waldrup wrote:
This is probably overkill for QRP but I wanted to do it right like we used to
do in broadcast.
The primary purpose of grounding bonding has NOTHING to do with radio --
it's for LIGHTNNG PROTECTION!
On 6/5/2020 10:46 AM, Walter Underwood wrote:
> C
Yes, we're supposed to have some technical background, but by asking
"where do I start" tends to indicate that there might just be an
insufficiency of necessary knowledge. I would hate to see someone die,
because I had failed to speak out. :-)
I also built several Elecraft products, including
Hey Jim,
If you think Cad-Welding a ground rod is fun to watch, take a look at
thermite welding of railroad tracks:
www.youtube.com/watch?v=5uxsFglz2ig
73
Frank
W3LPL
- Original Message -
From: "Jim Brown"
To: elecraft@mailman.qth.net
Sent: Friday, June 5, 2020 6:07:22 PM
Right sir I understand. I just mean I don't have large towers and big antennas.
Just want be protected since we are up high.
Chris
> On Jun 5, 2020, at 1:09 PM, Jim Brown wrote:
>
> On 6/5/2020 10:23 AM, Chris Waldrup wrote:
>> This is probably overkill for QRP but I wanted to do it right l
Neat!
Jim
On 6/5/2020 11:13 AM, donov...@starpower.net wrote:
Hey Jim,
If you think Cad-Welding a ground rod is fun to watch, take a look at
thermite welding of railroad tracks:
www.youtube.com/watch?v=5uxsFglz2ig
__
Elecraft mai
You say you checked the "fuse" and it is OK. In fact, there are two
fuses. If either has failed the amp won't power on. Then check the
voltage at the outlet from where the amp is powered.
If you don't know where to start looking,.if the above two items
are OK, then I suggest sendi
On 6/5/2020 2:02 PM, Jim Brown wrote:
On 6/5/2020 9:33 AM, Alan - G4GNX wrote:
Unless you really know what you're doing, then you should not remove
the lid. Fault finding could easily result in the need to power up
and expose yourself to many hidden dangers.
Ummm -- we're hams, and are suppos
Anyone that would desire to have a proper and reliable installation for
connecting a conductor to a ground rod. Me for one!
To that end, I've visited many ham stations where it seems there is a
mish mash of equipment connected in a hap hazard manner. I view this
is far from good engineer
On 6/5/2020 2:10 PM, Alan - G4GNX wrote:
Yes, we're supposed to have some technical background, but by asking
"where do I start" tends to indicate that there might just be an
insufficiency of necessary knowledge. I would hate to see someone die,
because I had failed to speak out. :-)
I also b
Just look at $11.00 per ground rod connection for Cad-Weld as compared
to $1.98 for a mechanical clamp. Which do you think a ham will choose ?
73
Bob, K4TAX
On 6/5/2020 12:46 PM, Walter Underwood wrote:
Cad-weld seems a easier than the other approach described. It is more robust
against c
In the mid-60's, on the other side of the planet, we ran missions
putting a transportable TACAN on the air for as long as the JP-4 for the
400 Hz turbine alternators lasted [~10-15 days]. Then, we piled all the
gear on top, several thermite packs on that, and pulled the tapes. It
reduced EVER
On 6/5/2020 2:41 PM, Bob McGraw K4TAX wrote:
You say you checked the "fuse" and it is OK. In fact, there are two
fuses. If either has failed the amp won't power on. Then check the
voltage at the outlet from where the amp is powered.
If you don't know where to start looking,.if the
I agree with Jim, K9YC on this. Grounding is for lightning
protection. To be effective, it should be outside of the
structure/house and be very low resistance. And all driven grounds
must be bonded back to the AC Mains ground. This is per NEC. Your
equipment, your house, and your life ma
Helping a friend to try to get the most out of his 2m equipped K3
especially for EME.
Is it recommended to use the internal preamp when the internal
transverter is in use? I'm guessing "no" due to to 20db transverter RX
gain.
On page 21 of the P3 Owners Manual it describes the integration of the
Actually four. There are two on the power supply board that protect the low
voltage supply. Since the front panel appears not to be powering up, it is
possible that one or both of these may be blown.
I don’t really have any suggestions for what might be wrong, so the best thing
to do is to cont
WOW!!! That was so-o-o neat!!!
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of
donov...@starpower.net
Sent: Friday, June 05, 2020 2:14 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] Self-fusing liquid electrical tape
That is why I used the mechanical clamps. I have 10 ground rods for a
perimeter ground wire around the house, 6 on the perimeter ground around
the workshop building (where the antenna feedlines first enter) and
another 4 in the antenna field. A total of 20 Cad Welds would have
exceeded my b
While I use an external transverter with my K3S, I do not suggest using
the K3 internal preamp. The transverter has adequate gain and also a
good low noise front end.
73
Bob, K4TAX
On 6/5/2020 2:03 PM, Jim Miller wrote:
Helping a friend to try to get the most out of his 2m equipped K3
espe
1 TOWER 6000-20 k 1HOLE WITH CONCRETE $1000
HUNDREDS OF FEET OF LMR 600 , RG213 ETC
4 ANTENNAS $1600
ROTOR 1600
cadwelds for the 9 10 BURIED ground rodsat the tower and few more
at the house MUST be in the budget.
why stray from a great job for a few hundred bucks.
To my mind, false economy.
Sent from my iPad
> On Jun 5, 2020, at 3:36 PM, Don Wilhelm wrote:
>
>
> That is why I used the mechanical clamps. I have 10 ground rods for a
> perimeter ground wire around the house, 6 on the perimeter ground around the
> workshop building (where the antenna f
Don, Are those all 8 ft ground rods driven vertical in ground without help
from a rock drill? Lots of rock in your area? Mike AC5P
On Friday, June 5, 2020, 03:10:11 PM CDT, W2xj wrote:
To my mind, false economy.
Sent from my iPad
> On Jun 5, 2020, at 3:36 PM, Don Wilhelm wrote:
It sure is! This was my first one, so I didn't really know what to
expect. I was a bit more casual with the rest, I admit:
https://youtu.be/j3MwokpxSco
On Fri, Jun 5, 2020 at 10:48 AM Walter Underwood wrote:
>
> Cad-weld seems a easier than the other approach described. It is more robust
> aga
All my ground rods are below ground level. I didn't want to take a chance of
failure so used 23 one-shots with #4 solid copper wire. Maybe that is one of
the reasons why I get away with never unhooking coax even when I watch
lightning strike the tower. One point ground for everything, lightning
Mike,
They are all 8 foot rods and were driven vertically with a fence post
driver and then finished off with a sledge.
I was 20 years younger at that time, I could not do it today. 3 or 4
rods in a day was all the shoulders could manage.
Yes, we hit some small rocks, but they will split is h
Or expense? Lessee... 20 (ground rods including 5 at the tower) times
$4 per clamp, vs $11-15 for little discernible gains.. adding over $300
in my grounding solution. Not a huge amount, but those costs add up
quickly. I went with clamps, all buried below grade.
I opted to tie the shop (bar
Now that was cool. Actually very hot 😊
N2TK, Tony
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of donov...@starpower.net
Sent: Friday, June 5, 2020 2:14 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] Self-fusing liquid electrical tape
Hey Jim,
If you t
On 6/5/2020 12:01 PM, Bob McGraw K4TAX wrote:
> I agree with Jim, K9YC on this. Grounding is for lightning
> protection. To be effective, it should be outside of the
> structure/house and be very low resistance. And all driven grounds
> must be bonded back to the AC Mains ground. This is per
This mornings setup.
https://youtu.be/yvPY6I6Uk0Y
--
Sent from my iPhone X
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
Thi
Tom -
I had the same experience a few months back. I talked with Elecraft Support,
and they had me check a few things. There was no obvious cause, except the
power supply board was dead.
They asked me to send it in, which I did, and they replaced the board.
Fortunately I got it back a coupl
I have 12 ground rods in the ring ground system around my house with the
radios in one room inside. the ground rods are all tied to each other
and the power ground. I agree the Cad welds can get expensive, that is
why I high temperature silver soldered the wire and ground rods
together. Not nor
A way for us no longer young people to drive ground rods is with a SDS
construction hammer and a ground rod driving bit. that is what
electricians use. I have a layer of shale about 2 feet deep where I live
and it takes less that 10 minutes per 8 foot ground rod driven below the
surface with th
Well, Dan, now you've gone and done it. I'm going to have to escape the lab to
do a little /PM outing with the KX2.
Also a bit jealous of your RV :)
Wayne
N6KR
> On Jun 5, 2020, at 2:22 PM, Dan Baker wrote:
>
> This mornings setup.
>
> https://youtu.be/yvPY6I6Uk0Y
>
> --
> Sent from my
Lyn,
On your KAT500, do contact support about it, and if they want you to
send it in, do so. Many techs are working from home, and while the time
from receipt at Elecraft until it is shipped may be longer, the process
still is working.
Who knows when this coronavirus thing will subside and th
Huh? I don't sell them...
73, and thanks,
Dave (NK7Z)
https://www.nk7z.net
ARRL Volunteer Examiner
ARRL Technical Specialist
ARRL Asst. Director, NW Division, Technical Resources
On 6/5/20 10:53 AM, Jim Brown wrote:
On 6/5/2020 8:17 AM, Phil Kane wrote:
For our commercial and public safety
co
Anyone know what those green wires are on each RR cross tie?
73, and thanks,
Dave (NK7Z)
https://www.nk7z.net
ARRL Volunteer Examiner
ARRL Technical Specialist
ARRL Asst. Director, NW Division, Technical Resources
On 6/5/20 12:28 PM, Edward T. Tanton wrote:
WOW!!! That was so-o-o neat!!!
-
I'm colorblind. If you're talking about the doobers at the end of each
tie over the foot of the rail, they're hold downs for the rails on
concrete ties. They take the place of spikes in wood ties whose purpose
is to maintain proper separation ["gauge"] between the rails. The rails
stand up b
Hi all,
so sorry to bother with that over here.
I did not found it in manual so I am trying to ask...
Can someone let me guide how to change the LCD brightness on KX3 please?
I do not means LCD backlight and I do not means LED brightness...
Thanks, Petr
-
73 - Petr, OK1RP
"Apple & Elecraf
HI, Due to the limited interest I have have decided not offer my KX3
equipment for sale at this time.
Sincerely
R Gilley
AD1G
> On Jun 4, 2020, at 19:49, richard gilley wrote:
>
> HI,
> I have a KX3 and PX3 with a KXPA100 available as a complete set up.
> Purchased September 2018.
LCDs are “on” or “off.” All they do is turn the substrate opaque.
The backlight heightens this contrast but you specifically aren’t asking
about the backlight.Possibly applying more voltage to the sense inputs
may make the contrast darker, but they may also smoke the display which
could ruin
Tonight my K-3 failed after being on for about an hour when I was
away.It displays ERR EE2.When powered on again the same ERR EE2 is
displayed.Tapping any button on the radio brings up a different error
message, such as DS1, FPF LOAD PENDING, BP1, LPF, IO3, IF1, and on and
on.Firmware reload is
Brain cramp -- I meant KF7P.
73, Jim K9YC
On 6/5/2020 4:06 PM, Dave Cole wrote:
Huh? I don't sell them...
73, and thanks,
Dave (NK7Z)
https://www.nk7z.net
ARRL Volunteer Examiner
ARRL Technical Specialist
ARRL Asst. Director, NW Division, Technical Resources
On 6/5/20 10:53 AM, Jim Brown wro
I spent a summer during my college years silver-soldering 120 radials to
ground screens for each of the 4-tower array of WSAZ.
73, Jim K9YC
On 6/5/2020 2:41 PM, Roger Steyaert wrote:
that is why I high temperature silver soldered the wire and ground rods
together. Not normal soft solder but th
try a 10 tower array. :-)
Sent from my iPad
> On Jun 5, 2020, at 10:33 PM, Jim Brown wrote:
>
> I spent a summer during my college years silver-soldering 120 radials to
> ground screens for each of the 4-tower array of WSAZ.
>
> 73, Jim K9YC
>
>> On 6/5/2020 2:41 PM, Roger Steyaert wrote:
Jim,
The K3 manual downloaded tonight, on page 69 says ...
==
ERR EE2
==
External EEPROM read/write test failed
EEPROM may be defective (front panel).
Cold shrink tubing is widely available on eBay, usually about ten dollars each
- Original Message -
From: "Peter Dougherty"
To: donov...@starpower.net, "Elecraft Reflector"
Sent: Friday, June 5, 2020 4:13:03 PM
Subject: RE: [Elecraft] FIXED--was NOT the feedline
First time I've ev
Ted, thanks for the note. I checked the error list immediately after
the failure and thought about that EPROM failure as a possibility. The
power supply is fine. The radio had been powered up and failed while I
had dinner. I know there are some pin connectors to the front panel
that could b
Jim,
1) Try an EEINIT ref pp66 of K3 owners manual rev D10.
2) Try to force a firmware down load, ref pp45 of K3 owners manual rev D10.
73 de Ben W4SC
Sent from Mail for Windows 10
__
Elecraft mailing list
Home: http://mailman.qth.net/
The only thing that would concern me about buying this (NOS) material of
unknown date of manufacture from eBay is that it does have a shelf life of 5
years in its pre-stretched state when properly stored (50-80 deg F at less than
75% relative humidity). If it’s been stored in someone’s hot humi
Hi Bill,
I have the K3 working again, currently going great stuff on 10m to give
it a good workout. Problem was one of those silly ones but also one that
I have just recently read about on the reflector, the case of a loose
TMP coax. In my case it turned out to be J7 on the KREF3 board.
Mart
79 matches
Mail list logo